NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
343 reportsMileage unknown · Dec 20, 2021
Forward Collision AvoidanceLane Departure
While driving on thruway, it began to snow.. One. by one the safety sensors reported failure due to being blocked. Even basic criosese control stopped working. As conditions cleared none of the sensors recovered. I pulled off at an exit to clear any remaining snow that may have been blocking the sensors. The sensors were already…
Read full complaint
While driving on thruway, it began to snow.. One. by one the safety sensors reported failure due to being blocked. Even basic criosese control stopped working. As conditions cleared none of the sensors recovered. I pulled off at an exit to clear any remaining snow that may have been blocking the sensors. The sensors were already clear, yet still reported. being blocked. I pulled into a car wash and. had the car washed and dried to make sure that every sensor was unobstructed. All of the sensors were still in a failure state. Not one sensor recovered. I had to turn off the car and restart to clear the sensor failures. This is a big problem when driving on a long trip. Every time it snows and a sensor fails, I have to exit the thruway and find a place to pull over and restart the car. In instances where roads are wet, cars ahead spray road mud and block the sensors. This happens constantly in upstate NY. Every few miles when the sensors is blocked the car will lose cruise control and most of the safety features. The only way to recover is pull off of the road to restart the car. It happened, several times on 50 mile drive. It's unnerving when it does. When weather conditions are poor, I want to get to my destination safely, without extra driving caused by exiting to restart and merging back on the thruway multiple times. Any other modern vehicle that I have driven will clear a sensor failure when the condition no longer exists, without restarting the car. The Mach-E refuses to clear sensors unless it's restarted. I do believe this compromises the safety of the driver and passengers by causing unnecessary extra driving with multiple instances of stopping and restarting while road conditions are ready poor.
NHTSA ODI #11444409
Mileage unknown · Dec 15, 2021
Visibility
The contact owns a 2021 Ford Mach-E. The contact received notification of NHTSA Campaign Numbers: 21V711000 (Visibility) and 21V712000 (Visibility) however, the dealer had not been returning the contact's calls to schedule the recall repair. The contact stated that the manufacturer had exceeded a reasonable amount of time for t…
Read full complaint
The contact owns a 2021 Ford Mach-E. The contact received notification of NHTSA Campaign Numbers: 21V711000 (Visibility) and 21V712000 (Visibility) however, the dealer had not been returning the contact's calls to schedule the recall repair. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repairs. The manufacturer was notified of the issue but did not provide any assistance. The contact had not experienced a failure. Parts distribution disconnect. Dealer did not have the parts to do the recall.
NHTSA ODI #11443932
Mileage unknown · Dec 8, 2021
Visibility
The contact owns a 2021 Ford Mustang Mach-E. The contact received notification of NHTSA Campaign Number: 21V711000 (Visibility) and 21V712000 (Visibility) however, the parts to do the recall repair were not yet available. The contact took the vehicle to the local dealer and it was confirmed that the parts were not yet available.…
Read full complaint
The contact owns a 2021 Ford Mustang Mach-E. The contact received notification of NHTSA Campaign Number: 21V711000 (Visibility) and 21V712000 (Visibility) however, the parts to do the recall repair were not yet available. The contact took the vehicle to the local dealer and it was confirmed that the parts were not yet available. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repairs. The manufacturer was made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
NHTSA ODI #11443132
Mileage unknown · Nov 11, 2021
Power Train
Second time in less than two weeks: Vehicle started making grinding noise, and a warning came up on the screen SHIFT SYSTEM FAULT, service soon. But the car came to a halt a hundred feet later, then would not get in or out of any gear, parking brake could not be released, vehicle could not get into Neutral so not able to push or…
Read full complaint
Second time in less than two weeks: Vehicle started making grinding noise, and a warning came up on the screen SHIFT SYSTEM FAULT, service soon. But the car came to a halt a hundred feet later, then would not get in or out of any gear, parking brake could not be released, vehicle could not get into Neutral so not able to push or roll it. I was barely able to get out of an intersection today (Nov 11), and rolled into a parking area on Oct 30 with the same fault. After about a half hour, vehicle could be moved but would show the fault shortly afterwards, locked up. Vehicle was towed on Oct 31 to dealership, they checked fault codes, performed some software updates and test drove 4 miles. They returned the car. Today, same thing happened. Car was at an intersection. Called AAA and still waiting for them to schedule a tow truck (required wheel lift and dolly). Fortunately I was on back roads today but this is a serious problem which would have been much worse on a highway. Car is not drivable. Again, this is the second time in two weeks!
NHTSA ODI #11440157
Mileage unknown · Oct 18, 2021
Unknown Or Other
The issue I'm describing is an inherent design flaw. This has not been discussed with third parties. The shift knob on this vehicle is a rotary knob with a configuration of PRND. The knob does not have positive stops in any direction and is only interlocked from moving out of park when the vehicle is not on. What this means: T…
Read full complaint
The issue I'm describing is an inherent design flaw. This has not been discussed with third parties. The shift knob on this vehicle is a rotary knob with a configuration of PRND. The knob does not have positive stops in any direction and is only interlocked from moving out of park when the vehicle is not on. What this means: To enter reverse from park: Turn knob one stop clockwise. To enter reverse from drive: Turn knob two stops counterclockwise. Forget you are in drive: Turn knob one stop clockwise and drive forward into the nearest object. There is nothing to stop you from doing this. I have owned the car for 6 months and have had several incidents where muscle memory has led me to nearly drive forward into a wall or other cars while parking.
NHTSA ODI #11437242
800 miles · Sep 23, 2021
Structure
The contact owns a 2021 Ford Mustang Mach-E. The contact stated while washing the vehicle he noticed a structural issue with the rear hatch not aligned properly on the vehicle. The contact called the local dealer who informed the contact that all vehicles under the model Mach-E were manufactured alike and there was no repair or …
Read full complaint
The contact owns a 2021 Ford Mustang Mach-E. The contact stated while washing the vehicle he noticed a structural issue with the rear hatch not aligned properly on the vehicle. The contact called the local dealer who informed the contact that all vehicles under the model Mach-E were manufactured alike and there was no repair or fix for the structural design. The vehicle was not repaired. The manufacturer was made aware of the issue. The failure mileage was approximately 800.
NHTSA ODI #11434086
Mileage unknown · Sep 14, 2021
Electrical System
The tailgate on our 2 Mustang Mach E’s have spontaneously opened on their own several times. One time narrowly missing one of our 2 year grandsons and another time impacting a closed garage door resulting in approximately $1,500 in damage (State Farm Insurance Claim). The issue was not able to be reproduced at the Ford Service …
Read full complaint
The tailgate on our 2 Mustang Mach E’s have spontaneously opened on their own several times. One time narrowly missing one of our 2 year grandsons and another time impacting a closed garage door resulting in approximately $1,500 in damage (State Farm Insurance Claim). The issue was not able to be reproduced at the Ford Service Department but has been reported to have occurred by several additional Mach E owners on the Mach E Forum. Both cars are available for inspection.
NHTSA ODI #11432909
Mileage unknown · Aug 25, 2021
Electrical System
This vehicle is sold with a single key FOB and an option to use Phone As A Key software. This feature has been a continual source of problems, as reported by almost every purchaser. It has been updated numerous times, including a dealer installed software update. This is a serious safety issue. To unlock the key, you can use …
Read full complaint
This vehicle is sold with a single key FOB and an option to use Phone As A Key software. This feature has been a continual source of problems, as reported by almost every purchaser. It has been updated numerous times, including a dealer installed software update. This is a serious safety issue. To unlock the key, you can use the traditional keypad on the door handle. This works consistently. However, once inside the vehicle, it can be impossible to have the car recognize the phone in my hand. Many owners report having to have the phone in a certain position, out of pocket or at a certain location in the car. Rebooting the phone, starting and stopping Bluetooth, getting out of the car, locking it and starting over again have all been mentioned. These work in a very hit or miss approach. I truly believe this software feature is still very much in its beta stages and should not be relied upon in lieu of a second key fob which is standard on every other Ford vehicle. To purchase the second FOB requires a purchase of the key and a programming service from the dealer, a $300 investment. While I understand there will always be software issues, and the Sync 4 center console certainly has them, the ability to start my car should not be part of this roadblock. Carrying the single FOB with me simply makes it more likely to be lost, and no way to have any assistance available to start my car and get me home safely. My fear is that anyone could easily be stranded in an isolated / dangerous location as a result of the failure of PAAK. The feature also requires a cell signal at the location to make it successfully validate the phone. This implies that driving the car in any desert or mountain area requires use of the actual FOB. I am requesting that Ford supply a second key FOB at no cost after I made a $60,000 investment. Consumer stated after several updates software still functions erratically.*JB
NHTSA ODI #11430567
Mileage unknown · Aug 22, 2021
Unknown Or Other
MachE relies on drivers using their phones as a key to get in and drive their vehicle. Ford does this and encourages drivers to not use the key fob, of which they provide only 1, less than the industry standard of 2. The app has a propensity for randomly failing as happened to me today. Could not use the app to get in the …
Read full complaint
MachE relies on drivers using their phones as a key to get in and drive their vehicle. Ford does this and encourages drivers to not use the key fob, of which they provide only 1, less than the industry standard of 2. The app has a propensity for randomly failing as happened to me today. Could not use the app to get in the vehicle, no amount of rebooting or other phone tests could get me in the vehicle. There is a backup code, but I forgot mine. Luckily I was able to reach my wife and use hers, but that is an unreasonable expectation. What if my wife were incapacitated and I needed to reach her? My car was immobile and Ford believes that is ok? They need to pick one option. Make the phone as key product work or call it an experiment (which it is) and provide all MachE customers two key fobs. There is serious safety impact of this middle road and consumers expect the “key” they are told to use to ALWAYS WORK!!!
NHTSA ODI #11430057
Mileage unknown · Aug 18, 2021
Unknown Or Other
Possible stability control system problem. Driving on wet road, following several other vehicles so my speed could not have been excessive. About half way through the corner experienced what felt like the start of a skid. I corrected it and continued on. My concern is that I am wondering if the stability control system ma…
Read full complaint
Possible stability control system problem. Driving on wet road, following several other vehicles so my speed could not have been excessive. About half way through the corner experienced what felt like the start of a skid. I corrected it and continued on. My concern is that I am wondering if the stability control system malfunctioned and it thought that it needed to do something which then actually started to put me into a skid. I have been driving for about 60 years including significant driving on snow and ice and have never experienced anything quite like what occurred. I only have about 2000 miles on the 2021Mach E so the tires are virtually new.
NHTSA ODI #11429641
Official recalls
13Jun 30, 2026
Ford Motor Company (Ford) is recalling certain 2021-2023 Mustang Mach E vehicles. The rear differential pinion shaft may fracture.
Consequence & remedy
Consequence: Differential pinion shaft fracture may result in a loss of drive power, or unintended vehicle movement if the vehicle is in park without the parking brake applied, increasing the risk of a crash.
Remedy: Dealers will repair or replace the rear differential assembly as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed July 13, 2026. Additional letters will be sent once the remedy is available, anticipated in late December 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S50.
Aug 8, 2025
Ford Motor Company (Ford) is recalling certain 2021 Mach-E vehicles that were repaired incorrectly under recall 24V777. An Over-The-Air (OTA) update to the Anti-lock Braking System (ABS) may result in a loss of power brake assist, ABS, Electronic Stability Control, Traction Control, and driver assistance features.
Consequence & remedy
Consequence: A loss of power brake assist can increase the distance required to stop the vehicle. Additionally, a disabled antilock brake system and/or stability control system can result in a loss of vehicle control. Either of these scenarios can increase the risk of a crash.
Remedy: Dealers will update the ABS calibration software, free of charge. Owner notification letters were mailed September 18, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S81.
Jun 13, 2025
Ford Motor Company (Ford) is recalling certain 2021-2025 Mustang Mach E vehicles. In the event of a low battery charge, the electronic door latches may remain locked once the driver or front passenger exits and shuts the door, possibly trapping someone who is unable to use the inside door release handles, such as a child in the back seat.
Consequence & remedy
Consequence: The inability to enter or exit the vehicle in an emergency increases the risk of injury.
Remedy: Dealers will update the Powertrain Control Module (PCM) and the Secondary On-Board Diagnostic Control Module C (SOBDMC) software, free of charge. Owner notification letters were mailed to 2021-2025 Mustang Mach-E owners September 12, 2025. Additionally, Owner notification letters were mailed to 2024-2025 Mustang Mach-E owners July 10, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S65.
Additional source detail variants (2)
Electrical System:body Control Module:software
Ford Motor Company (Ford) is recalling certain 2021-2025 Mustang Mach E vehicles. In the event of a low battery charge, the electronic door latches may remain locked once the driver or front passenger exits and shuts the door, possibly trapping someone who is unable to use the inside door release handles, such as a child in the back seat.
Consequence: The inability to enter or exit the vehicle in an emergency increases the risk of injury.
Remedy: Dealers will update the Powertrain Control Module (PCM) and the Secondary On-Board Diagnostic Control Module C (SOBDMC) software, free of charge. Owner notification letters were mailed to 2021-2025 Mustang Mach-E owners September 12, 2025. Additionally, Owner notification letters were mailed to 2024-2025 Mustang Mach-E owners July 10, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S65.
Latches/locks/linkages:doors:latch
Ford Motor Company (Ford) is recalling certain 2021-2025 Mustang Mach E vehicles. In the event of a low battery charge, the electronic door latches may remain locked once the driver or front passenger exits and shuts the door, possibly trapping someone who is unable to use the inside door release handles, such as a child in the back seat.
Consequence: The inability to enter or exit the vehicle in an emergency increases the risk of injury.
Remedy: Dealers will update the Powertrain Control Module (PCM) and the Secondary On-Board Diagnostic Control Module C (SOBDMC) software, free of charge. Owner notification letters were mailed to 2021-2025 Mustang Mach-E owners September 12, 2025. Additionally, Owner notification letters were mailed to 2024-2025 Mustang Mach-E owners July 10, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S65.
May 9, 2025
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to delay, freeze, or not display when the vehicle is in reverse.
Consequence & remedy
Consequence: A frozen or missing rearview camera image can reduce the driver's view behind the vehicle, increasing the risk of a crash.
Remedy: The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49.
Feb 28, 2025
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles previously repaired incorrectly under recall number 22V-412. The high voltage battery main contactors may overheat.
Consequence & remedy
Consequence: An overheated high voltage battery contactor may cause the vehicle to lose drive power, increasing the risk of a crash.
Remedy: Dealers will update the on-board software, free of charge. Owner notification letters were mailed April 11, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S14.
Oct 18, 2024
Ford Motor Company (Ford) is recalling certain 2021 Mach-E vehicles. An Over-The-Air (OTA) update to the Anti-lock Braking System (ABS) may result in a loss of power brake assist, ABS, Electronic Stability Control, Traction Control, and driver assistance features.
Consequence & remedy
Consequence: A loss of power brake assist can extend the distance required to stop the vehicle. Additionally, a disabled antilock brake system and/or stability control system can result in a loss of vehicle control. Either of these scenarios can increase the risk of a crash.
Remedy: Dealers will update the ABS calibration, free of charge. Owner notification letters were mailed November 5, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S65.
Oct 13, 2023
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles equipped with an extended range battery. The high voltage battery main contactors may overheat.
Consequence & remedy
Consequence: An overheated high voltage battery contactor can result in a loss of drive power, increasing the risk of a crash.
Remedy: Dealers will replace the high voltage battery junction box, free of charge. Owner notification letters were mailed December 29, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S56. Vehicles included in this recall that were previously repaired under recall 22V-412 will need to have the new remedy completed.
Jun 10, 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles. The high voltage battery main contactors may overheat.
Consequence & remedy
Consequence: An overheated high voltage battery contactor may cause the vehicle to lose drive power, increasing the risk of a crash.
Remedy: Dealers will update the on-board software, free of charge. Owner notification letters were mailed on July 8, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S41.
May 13, 2022
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles equipped with all-wheel drive. The powertrain control module (PCM) functional safety software may fail to detect a software error, resulting in unintended acceleration, unintended deceleration, or a loss of drive power.
Consequence & remedy
Consequence: Unintended acceleration, unintended deceleration, or a loss of drive power increases the risk of a crash.
Remedy: The PCM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed June 9, 2022. Owners may contact Ford customer service at 1-800-436-7332. Ford's number for this recall is 22S29.
Additional source detail variants (2)
Power Train:automatic Transmission:control Module:software
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles equipped with all-wheel drive. The powertrain control module (PCM) functional safety software may fail to detect a software error, resulting in unintended acceleration, unintended deceleration, or a loss of drive power.
Consequence: Unintended acceleration, unintended deceleration, or a loss of drive power increases the risk of a crash.
Remedy: The PCM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed June 9, 2022. Owners may contact Ford customer service at 1-800-436-7332. Ford's number for this recall is 22S29.
Vehicle Speed Control
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles equipped with all-wheel drive. The powertrain control module (PCM) functional safety software may fail to detect a software error, resulting in unintended acceleration, unintended deceleration, or a loss of drive power.
Consequence: Unintended acceleration, unintended deceleration, or a loss of drive power increases the risk of a crash.
Remedy: The PCM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed June 9, 2022. Owners may contact Ford customer service at 1-800-436-7332. Ford's number for this recall is 22S29.
Dec 16, 2021
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E and 2022 Maverick vehicles. The rear seat belt buckles may not be properly attached to the rear floor assembly. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 208, "Occupant Crash Protection," and 210, "Seat Belt Assembly Anchorages."
Consequence & remedy
Consequence: Improperly attached seat belts may not adequately restrain an occupant in a crash, increasing the risk of injury.
Remedy: Dealers will repair the rear seat belt buckle attachments, free of charge. Owner notification letters were mailed January 28, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C36.
Sep 14, 2021
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 212, "Windshield Mounting."
Consequence & remedy
Consequence: A windshield that separates from a vehicle during a crash can increase the risk of injury.
Remedy: Dealers will remove and reinstall the windshield, free of charge. Owner notification letters were mailed on October 29, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C22.
Additional source detail variants (2)
Visibility:windshield:critical Fasteners
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 212, "Windshield Mounting."
Consequence: A windshield that separates from a vehicle during a crash can increase the risk of injury.
Remedy: Dealers will remove and reinstall the windshield, free of charge. Owner notification letters were mailed on October 29, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C22.
Visibility:windshield
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 212, "Windshield Mounting."
Consequence: A windshield that separates from a vehicle during a crash can increase the risk of injury.
Remedy: Dealers will remove and reinstall the windshield, free of charge. Owner notification letters were mailed on October 29, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C22.
Sep 14, 2021
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles. The vehicle's panoramic roof glass panel may not have been properly bonded to the vehicle, which could allow it to detach.
Consequence & remedy
Consequence: A roof panel that separates from a vehicle can become a road hazard, increasing the risk of a crash or injury.
Remedy: Dealers will apply additional urethane adhesive, free of charge. Owner notification letters were mailed October 29, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S42.
Mar 5, 2021
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles. The front subframe bolts may not have been tightened properly during assembly, which could result in loose bolts.
Consequence & remedy
Consequence: Loose subframe bolts may reduce the vehicle's performance in a crash, increasing the risk of injury.
Remedy: Ford will notify owners, and dealers will inspect the front subframe bolts and tighten them as necessary, free of charge. The recall began April 2, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S09.
Additional source detail variants (2)
Structure:frame And Members
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles. The front subframe bolts may not have been tightened properly during assembly, which could result in loose bolts.
Consequence: Loose subframe bolts may reduce the vehicle's performance in a crash, increasing the risk of injury.
Remedy: Ford will notify owners, and dealers will inspect the front subframe bolts and tighten them as necessary, free of charge. The recall began April 2, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S09.
Suspension:subframe/mounting Bracket
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles. The front subframe bolts may not have been tightened properly during assembly, which could result in loose bolts.
Consequence: Loose subframe bolts may reduce the vehicle's performance in a crash, increasing the risk of injury.
Remedy: Ford will notify owners, and dealers will inspect the front subframe bolts and tighten them as necessary, free of charge. The recall began April 2, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S09.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4EA25001 · Collisions Involving Ford Bluecruise
Opened Jan 17, 2025 · No close date supplied
Status: open (inferred from source dates) · Electrical System:adas
On April 25, 2024, NHTSA’s Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24012) to assess BlueCruise, a partial driving automation system available on certain vehicles manufactured by Ford Motor Company (Ford). NHTSA opened the investigation after the agency received notice of two fatal collisions involving BlueCruise-equipped Ford Mustang Mach-E vehicles. Based on the incidents, NHTSA scoped the investigation to 2021-2024 Mustang Mach-E vehicles equipped with BlueCruise. In June 2024, ODI sent an Information Request (IR) letter to Ford requiring that it provide certain information pertaining to crashes, non-crash reports, and technical specifications that relate to BlueCruise, as well as other Ford partial driving automation systems that offer lane and speed maintenance. In its response to ODI’s IR, Ford stated that there are 2,539,962 Ford and Lincoln vehicles (including subject and peer vehicles) equipped with a partial driving automation system within the scope of the request. The majority of these vehicles are equipped with a system that Ford calls Lane Centering Assist (LCA), which is a hands-on partial driving automation system that combines longitudinal control authority governed by Adaptive Cruise Control (ACC) and lateral control authority governed by a steerable path. LCA is offered on a wide range of Ford and Lincoln models beginning in model year 2019. Vehicles that are equipped with BlueCruise, the focus of this investigation, have LCA capability and additionally offer hands-free partial driving automation when certain conditions are met. Hands-free BlueCruise operation is only offered on certain roadways and system availability is geofenced using vehicle GPS. BlueCruise-equipped vehicles employ a camera-based driver monitoring system to determine driver attentiveness to the roadway. BlueCruise was introduced in model year 2021 and is currently available in a select range of Ford and Lincoln vehicles. For BlueCruise- and LCA-equipped vehicles, both ACC and Pre-Collision Assist (PCA) features use a combination of camera and radar sensing technologies to detect and classify objects. ACC is specifically designed to detect vehicles (including cars, trucks, and motorcycles) and bicycles in front of the subject vehicle which are either stationary or moving in the same direction as the subject vehicle. Through this investigation, limitations in the detection of stationary vehicles in certain conditions have been identified. Specifically, due to the potential for false detection of stationary objects at long distances, Ford designed ACC to inhibit any response to reported stationary objects when the subject vehicle’s approach speed is at or above 62 mph. Additionally, system performance may be limited when there is poor visibility due to insufficient illumination. In addition to reviewing Ford’s response to ODI’s IR, the agency conducted a review of crash and non-crash reports identified collectively through Ford’s IR response, incident reporting through Standing General Order 2021-01 (SGO), and NHTSA vehicle owner questionnaires. In total, 32 crashes and 2,004 non-crash reports on subject and peer Ford vehicles were identified across manufacturer and ODI data sources. A detailed analysis of each crash was conducted including the review of any available police reports, photographs, data recovered from in-vehicle event data recorders, connected vehicle data, and/or other information. In both fatal collisions referenced in the PE24012 opening resume, the subject Ford Mustang Mach-E vehicle was traveling over 70 mph on a controlled-access highway during nighttime lighting conditions with hands-free BlueCruise engaged when it collided with a stationary vehicle. Analysis of data imaged from the vehicles’ event data recorders demonstrates that in each incident, the driver did not apply the brakes or take evasive steering action, and no deceleration was initiated by either the BlueCruise system or PCA prior to impact. Through the agency’s crash analysis, four additional frontal collisions were identified where the subject Ford impacted a stopped or slow-moving lead vehicle or another stationary object located in the travel lane. Two of these four incidents involved BlueCruise-equipped Ford Mustang Mach-E vehicles (included in the failure report summary along with the fatal collisions discussed above), while the other two involved other Ford models equipped with the LCA system. Additionally, a trend was identified through analysis of the non-crash reports relating to allegations that ACC (the longitudinal component of both BlueCruise and LCA) failed to detect and/or respond to a stopped or slow-moving lead vehicle. In these reports, consumers often describe that the absence of deceleration initiated by ACC was unexpected and required harsh manual braking or intervention from the PCA to avoid a frontal collision with the lead vehicle. Based on NHTSA’s analysis, system limitations relating to the detection of stationary vehicles while traveling at highway speeds and in nighttime lighting conditions appear to be factors in collisions under investigation and several apparently similar near-miss, non-crash reports. This Engineering Analysis (EA) is being opened to further investigate these system limitations and to evaluate drivers’ ability to respond to scenarios that exceed system limitations. During the EA, the agency expects to, among other things, perform vehicle evaluations, review additional technical information, and perform additional analysis of related crashes and non-crash reports. The crashes included in the failure report summary can be found at NHTSA.gov under the following SGO report identification numbers: 502-7268, 502-7426, 502-6852, 502-8738.
PE24012 · Collisions Involving Ford Bluecruise
Opened Apr 25, 2024 · Closed Jan 17, 2025
Status: closed (inferred from source dates) · Electrical System:adas
On April 25, 2024, NHTSA’s Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24012) to assess BlueCruise, a partial driving automation system available on certain vehicles manufactured by Ford Motor Company (Ford). NHTSA opened the investigation after the agency received notice of two fatal collisions involving BlueCruise-equipped Ford Mustang Mach-E vehicles. Based on the incidents, NHTSA scoped the investigation to 2021-2024 Mustang Mach-E vehicles equipped with BlueCruise. In June 2024, ODI sent an Information Request (IR) letter to Ford requiring that it provide certain information pertaining to crashes, non-crash reports, and technical specifications that relate to BlueCruise, as well as other Ford partial driving automation systems that offer lane and speed maintenance. In its response to ODI’s IR, Ford stated that there are 2,539,962 Ford and Lincoln vehicles (including subject and peer vehicles) equipped with a partial driving automation system within the scope of the request. The majority of these vehicles are equipped with a system that Ford calls Lane Centering Assist (LCA), which is a hands-on partial driving automation system that combines longitudinal control authority governed by Adaptive Cruise Control (ACC) and lateral control authority governed by a steerable path. LCA is offered on a wide range of Ford and Lincoln models beginning in model year 2019. Vehicles that are equipped with BlueCruise, the focus of this investigation, have LCA capability and additionally offer hands-free partial driving automation when certain conditions are met. Hands-free BlueCruise operation is only offered on certain roadways and system availability is geofenced using vehicle GPS. BlueCruise-equipped vehicles employ a camera-based driver monitoring system to determine driver attentiveness to the roadway. BlueCruise was introduced in model year 2021 and is currently available in a select range of Ford and Lincoln vehicles. For BlueCruise- and LCA-equipped vehicles, both ACC and Pre-Collision Assist (PCA) features use a combination of camera and radar sensing technologies to detect and classify objects. ACC is specifically designed to detect vehicles (including cars, trucks, and motorcycles) and bicycles in front of the subject vehicle which are either stationary or moving in the same direction as the subject vehicle. Through this investigation, limitations in the detection of stationary vehicles in certain conditions have been identified. Specifically, due to the potential for false detection of stationary objects at long distances, Ford designed ACC to inhibit any response to reported stationary objects when the subject vehicle’s approach speed is at or above 62 mph. Additionally, system performance may be limited when there is poor visibility due to insufficient illumination. In addition to reviewing Ford’s response to ODI’s IR, the agency conducted a review of crash and non-crash reports identified collectively through Ford’s IR response, incident reporting through Standing General Order 2021-01 (SGO), and NHTSA vehicle owner questionnaires. In total, 32 crashes and 2,004 non-crash reports on subject and peer Ford vehicles were identified across manufacturer and ODI data sources. A detailed analysis of each crash was conducted including the review of any available police reports, photographs, data recovered from in-vehicle event data recorders, connected vehicle data, and/or other information. In both fatal collisions referenced in the PE24012 opening resume, the subject Ford Mustang Mach-E vehicle was traveling over 70 mph on a controlled-access highway during nighttime lighting conditions with hands-free BlueCruise engaged when it collided with a stationary vehicle. Analysis of data imaged from the vehicles’ event data recorders demonstrates that in each incident, the driver did not apply the brakes or take evasive steering action, and no deceleration was initiated by either the BlueCruise system or PCA prior to impact. Through the agency’s crash analysis, four additional frontal collisions were identified where the subject Ford impacted a stopped or slow-moving lead vehicle or another stationary object located in the travel lane. Two of these four incidents involved BlueCruise-equipped Ford Mustang Mach-E vehicles (included in the failure report summary along with the fatal collisions discussed above), while the other two involved other Ford models equipped with the LCA system. Additionally, a trend was identified through analysis of the non-crash reports relating to allegations that ACC (the longitudinal component of both BlueCruise and LCA) failed to detect and/or respond to a stopped or slow-moving lead vehicle. In these reports, consumers often describe that the absence of deceleration initiated by ACC was unexpected and required harsh manual braking or intervention from the PCA to avoid a frontal collision with the lead vehicle. Based on NHTSA’s analysis, system limitations relating to the detection of stationary vehicles while traveling at highway speeds and in nighttime lighting conditions appear to be factors in collisions under investigation and several apparently similar near-miss, non-crash reports. This Preliminary Evaluation is being upgraded to an Engineering Analysis (EA25001) to further investigate these system limitations and to evaluate drivers’ ability to respond to scenarios that exceed system limitations. During the EA, the agency expects to, among other things, perform vehicle evaluations, review additional technical information, and perform additional analysis of related crashes and non-crash reports. The crashes included in the failure report summary can be found at NHTSA.gov under the following SGO report identification numbers: 502-7268, 502-7426, 502-6852, 502-8738.
RQ23004 · High Voltage Battery Contactor Failure
Opened Aug 17, 2023 · Closed Dec 6, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System:traction Battery:management System/energy Control Module (bms/becm):software; Engine And Engine Cooling:engine:engine Control Module (ecu/ecm):software
On August 17, 2023, the Office of Defects Investigations (ODI) opened RQ23-004 to investigate instances of loss of motor power due to overheating high voltage battery contactors in model year (MY) 2021-2022 Ford Mustang Mach-E vehicles (subject vehicles). This Recall Query (RQ) was opened after receiving 12 consumer complaints alleging a high voltage battery main contactor failure in subject vehicles that were included in Recall 22V-412 and remedied prior to the reported incidents. The remedy in 22V-412 was a Secondary On-Board Diagnostic Control Module (SOBDMC) software update to monitor contactor temperature and reduce battery power to prevent damage to the contactor, and a Battery Energy Control Module (BECM) software update to monitor contactor resistance to identify an overheated contactor and reduce vehicle power to prevent further damage. On October 13, 2023, Ford filed Recall 23V-687 of 34,762 2021-2022 Ford Mustang Mach-E vehicles produced from May 27, 2020 to May 24, 2022 with recalled Bussed Electrical Center parts NK48-10C666-AA, NK48-10C666-BA, or LK98-10C666-AB. Affected vehicles are equipped with the extended range battery. Ford stated that preexisting damage to the contactors caused by heat and accumulated wear may reduce the effectiveness of the software update remedy in 22V-412. The remedy of 23V-687 is to complete a replacement of the Bussed Electrical Center, or High Voltage Battery Junction Box. In addition, Ford stated that subject vehicles equipped with standard range batteries, in comparison to vehicles equipped with extended range batteries, are less at risk of experiencing this failure due to their smaller battery capacity and lower output electric drive motors. In view of the recall action taken by Ford, ODI is closing this investigation. ODI will continue to monitor reports of this failure in both extended range and standard range models. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Electrical System:propulsion System:traction Battery:management System/energy Control Module (bms/becm):software
On August 17, 2023, the Office of Defects Investigations (ODI) opened RQ23-004 to investigate instances of loss of motor power due to overheating high voltage battery contactors in model year (MY) 2021-2022 Ford Mustang Mach-E vehicles (subject vehicles). This Recall Query (RQ) was opened after receiving 12 consumer complaints alleging a high voltage battery main contactor failure in subject vehicles that were included in Recall 22V-412 and remedied prior to the reported incidents. The remedy in 22V-412 was a Secondary On-Board Diagnostic Control Module (SOBDMC) software update to monitor contactor temperature and reduce battery power to prevent damage to the contactor, and a Battery Energy Control Module (BECM) software update to monitor contactor resistance to identify an overheated contactor and reduce vehicle power to prevent further damage. On October 13, 2023, Ford filed Recall 23V-687 of 34,762 2021-2022 Ford Mustang Mach-E vehicles produced from May 27, 2020 to May 24, 2022 with recalled Bussed Electrical Center parts NK48-10C666-AA, NK48-10C666-BA, or LK98-10C666-AB. Affected vehicles are equipped with the extended range battery. Ford stated that preexisting damage to the contactors caused by heat and accumulated wear may reduce the effectiveness of the software update remedy in 22V-412. The remedy of 23V-687 is to complete a replacement of the Bussed Electrical Center, or High Voltage Battery Junction Box. In addition, Ford stated that subject vehicles equipped with standard range batteries, in comparison to vehicles equipped with extended range batteries, are less at risk of experiencing this failure due to their smaller battery capacity and lower output electric drive motors. In view of the recall action taken by Ford, ODI is closing this investigation. ODI will continue to monitor reports of this failure in both extended range and standard range models. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine And Engine Cooling:engine:engine Control Module (ecu/ecm):software
On August 17, 2023, the Office of Defects Investigations (ODI) opened RQ23-004 to investigate instances of loss of motor power due to overheating high voltage battery contactors in model year (MY) 2021-2022 Ford Mustang Mach-E vehicles (subject vehicles). This Recall Query (RQ) was opened after receiving 12 consumer complaints alleging a high voltage battery main contactor failure in subject vehicles that were included in Recall 22V-412 and remedied prior to the reported incidents. The remedy in 22V-412 was a Secondary On-Board Diagnostic Control Module (SOBDMC) software update to monitor contactor temperature and reduce battery power to prevent damage to the contactor, and a Battery Energy Control Module (BECM) software update to monitor contactor resistance to identify an overheated contactor and reduce vehicle power to prevent further damage. On October 13, 2023, Ford filed Recall 23V-687 of 34,762 2021-2022 Ford Mustang Mach-E vehicles produced from May 27, 2020 to May 24, 2022 with recalled Bussed Electrical Center parts NK48-10C666-AA, NK48-10C666-BA, or LK98-10C666-AB. Affected vehicles are equipped with the extended range battery. Ford stated that preexisting damage to the contactors caused by heat and accumulated wear may reduce the effectiveness of the software update remedy in 22V-412. The remedy of 23V-687 is to complete a replacement of the Bussed Electrical Center, or High Voltage Battery Junction Box. In addition, Ford stated that subject vehicles equipped with standard range batteries, in comparison to vehicles equipped with extended range batteries, are less at risk of experiencing this failure due to their smaller battery capacity and lower output electric drive motors. In view of the recall action taken by Ford, ODI is closing this investigation. ODI will continue to monitor reports of this failure in both extended range and standard range models. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
Illustration