NHTSA owner reports · September 18, 2026 snapshot.
Fuel/propulsion System complaints
47 reportsClear category filterMileage unknown · Apr 19, 2024
Electrical SystemFuel/propulsion System
On April 10, 2024, my vehicle experienced a warning message to service vehicle and a sudden loss of power while I was driving on the freeway. The issue was caused by a failure in my high voltage battery junction block. Something that Ford had already issued a software update vehicle to my vehicle for a recall. However clearly …
Read full complaint
On April 10, 2024, my vehicle experienced a warning message to service vehicle and a sudden loss of power while I was driving on the freeway. The issue was caused by a failure in my high voltage battery junction block. Something that Ford had already issued a software update vehicle to my vehicle for a recall. However clearly the software update was not an appropriate fix for the issue and should not be considered fulfillment of the recall. In fact, Ford has an open recall for the extended battery configuration of my vehicle to proactively replace this defective part. I am reporting this issue to the NHTSA because clearly the software ‘fix’ did not resolve the safety issue AND it’s scary that standard range batteries are neglected from the overall recall that applied to the rest of the model. Ford needs to be proactively addressing this issue for all affected model years, not just certain configurations. Frankly it is wild that the NHTSA accepted a software update as an appropriate recall fix for a hardware component overheating and melting while driving. It didn’t work and should not be considered a fix.
NHTSA ODI #11584119
Mileage unknown · Apr 17, 2024
Fuel/propulsion SystemService BrakesSteering
This is a follow up to ODI 11510437 that was filed via the phone in 2/2023 related to now NHTSA Recall 23V687. The vehicle in question experienced exactly the issue described in the recall notice. Our incident was part of the NHTSA investigation. The vehicle had its high voltage battery junction box replaced in +/- March 2023…
Read full complaint
This is a follow up to ODI 11510437 that was filed via the phone in 2/2023 related to now NHTSA Recall 23V687. The vehicle in question experienced exactly the issue described in the recall notice. Our incident was part of the NHTSA investigation. The vehicle had its high voltage battery junction box replaced in +/- March 2023, but the new box was the same design as the old box that is poorly engineered. Notices sent out in Fall of 2023 indicating that there was a recall were not sent to us for this vehicle. Similarly, the notice sent in April 2024 informing Mach E owners to schedule appointments at their dealer was not sent to us for this vehicle. Upon contacting Ford, they indicated that this vehicle is not part of this recall. After insisting on speaking to a supervisor, he claimed that it was now a part of the recall but refused to provide me any written acknowledgment of this. When pressed further he then said that our vehicle was not part of the recall because the part was already replaced. When I explained that the part replace was the same defective part he told me to call the dealership or NHTSA because he would do nothing further. He went on to say that there was nothing further he would or could do, nor would it transfer me to anybody at Ford that could address our unique circumstances. Upon calling NHTSA they advised, (amongst other things), that we file a complaint via this portal.
NHTSA ODI #11583689
Mileage unknown · Oct 6, 2023
Fuel/propulsion SystemPower Train
Dashboard warnings about the high-voltage battery due to a fault. There is a known issue with the HVBJB (high-voltage battery junction box) plus a powertrain malfunction warning..
NHTSA ODI #11548691
Mileage unknown · Sep 29, 2023
Electrical SystemFuel/propulsion System
We came out to our parked car and got a message that said Stop Safely Now. The vehicle would not shift into gear. The dealership had confirmed that the high voltage junction box has failed. We did not get the Service Vehicle Soon warning prior to the failure, despite having had the recall software update applied. The first sign …
Read full complaint
We came out to our parked car and got a message that said Stop Safely Now. The vehicle would not shift into gear. The dealership had confirmed that the high voltage junction box has failed. We did not get the Service Vehicle Soon warning prior to the failure, despite having had the recall software update applied. The first sign of failure was a loss of motive power. This is a safety issue because loss of motive power while driving can result in loss of control of the vehicle. The loss of heating and cooling combined with the loss of motive power is also a significant safety risk if the failure occurs in a remote location experiencing extreme temperatures. The part has yet to be replaced, but I’m sure Ford will be retaining it for inspection.
NHTSA ODI #11547361
Mileage unknown · Aug 22, 2023
Fuel/propulsion SystemPower Train
Shortly after entering the freeway on August 18, 2023, my vehicle experienced a powertrain malfunction and displayed a Service Vehicle Soon warning light along with a vehicle with an exclamation point light and a wrench light. Motive power was reduced. I received a Diagnostic Test Code of P0ADA, indicating that there was a hybri…
Read full complaint
Shortly after entering the freeway on August 18, 2023, my vehicle experienced a powertrain malfunction and displayed a Service Vehicle Soon warning light along with a vehicle with an exclamation point light and a wrench light. Motive power was reduced. I received a Diagnostic Test Code of P0ADA, indicating that there was a hybrid powertrain fault. The dealer has confirmed the code and is ordering a replacement part.
NHTSA ODI #11540062
Mileage unknown · Aug 22, 2023
Electrical SystemFuel/propulsion SystemSteering
I am filing this complaint regarding the potential failure of the High Voltage Battery Junction Box. There have been many failures reported on the forums some experiencing multiple failures. Ford provided a software update that supposedly predicts an impending failure reducing available propulsion power. I do not feel comfortabl…
Read full complaint
I am filing this complaint regarding the potential failure of the High Voltage Battery Junction Box. There have been many failures reported on the forums some experiencing multiple failures. Ford provided a software update that supposedly predicts an impending failure reducing available propulsion power. I do not feel comfortable driving a vehicle with a ticking time bomb. Losing propulsion power while driving at highway speeds could result in a serious safety senerio. I would like to see Ford provide a real fix.
NHTSA ODI #11540005
Mileage unknown · Aug 22, 2023
Electrical SystemFuel/propulsion SystemSuspension
The HVBJB subassembly in ALL Ford Mach-e vehicles has known defects with 'under-designed' main contacts that are known to fail under normal charging and driving conditions as outlined in current open Ford recall notice. Unfortunately, the internal damage to contactors is not visible externally, and warning notices on display on…
Read full complaint
The HVBJB subassembly in ALL Ford Mach-e vehicles has known defects with 'under-designed' main contacts that are known to fail under normal charging and driving conditions as outlined in current open Ford recall notice. Unfortunately, the internal damage to contactors is not visible externally, and warning notices on display only AFTER the damage has occurred, and can result in sudden loss of propulsion power at highway speed, loss of power steering, and power brakes... and failure of other 12v systems due to failure to charge the 12v battery properly after contacts are damaged. Less catastrophic results can include failure to start; which can 'strand' driver's and passengers in remote areas, bad weather conditions, as well as cause loss of use for weeks due to delays in replacement parts and local Dealerships needing equipment and training to effect removal/replacement of faulty unit with a new HVBJB having re-designed 'beefier' components. My complaint is that Ford's recall notice 22s41 is a software-only attempt to prevent future damage, and does not require removal of the part(s) which are KNOWN TO FAIL to be replaced with the re-designed components which are available, and have been used to repair failures under warranty. I have no way of inspecting the original equipment to evaluate current condition; and failure can result in sudden and unexpected loss of power, steering, and braking as well as potentially 'stranding me' in unsafe conditions unable to re-start my vehicle. I would like to see NHTSA strengthen the Ford recall to include both improved software AND removal/replacement of the HVBJB sub-assembly with the new 'beefier' parts.
NHTSA ODI #11539965
Mileage unknown · Aug 21, 2023
Electrical SystemFuel/propulsion System
After receiving the remedy to NHTSA campaign 22V-412 on Aug 5, 2022 via a Ford Power-Up over-the-air update, my high-voltage battery contactors still overheated and failed on Oct 25, 2022, requiring warrantied replacement by my Ford dealer on Oct 27, 2022.
NHTSA ODI #11539925
Mileage unknown · Aug 21, 2023
Electrical SystemFuel/propulsion SystemPower Train
On Friday 8/18/23 I was driving down a major freeway and my Mach-E jolted violently. I then received a "Stop Safely Now" and "Service Vehicle Soon" message. The vehicle lost all power at this time. Being on a very busy freeway my safety was at risk and I was luckily able to coast over to the right shoulder. The car refused to "s…
Read full complaint
On Friday 8/18/23 I was driving down a major freeway and my Mach-E jolted violently. I then received a "Stop Safely Now" and "Service Vehicle Soon" message. The vehicle lost all power at this time. Being on a very busy freeway my safety was at risk and I was luckily able to coast over to the right shoulder. The car refused to "start" after pulling over however the 12v battery did work so I was able to use accessories. Once towed to the dealer I was able to confirm a P0AA2 TSB code that indicated that a conductor was stuck open on the high voltage junction box. This was supposed to be fixed by a previous recall software update that FORD uploaded to my car however that was not the case. I am now without a car for 2 weeks but more importantly I am concerned for the safety of other Mach-E drivers as I am reading that this can happen again even after a hardware fix.
NHTSA ODI #11539803
Mileage unknown · Mar 10, 2023
Electrical SystemFuel/propulsion SystemVehicle Speed Control
Unintended acceleration from a stop when pushing accelerator. Has happened 2 times in the last 2 days. I touched the throttle from a stop 2 time and it took off like I put the accelerator to full throttle (which I didn’t). Very dangerous situation in parking lots or around pedestrians. I have scheduled an apt with my local deale…
Read full complaint
Unintended acceleration from a stop when pushing accelerator. Has happened 2 times in the last 2 days. I touched the throttle from a stop 2 time and it took off like I put the accelerator to full throttle (which I didn’t). Very dangerous situation in parking lots or around pedestrians. I have scheduled an apt with my local dealer.
NHTSA ODI #11511215
Official recalls
13Jun 30, 2026
Ford Motor Company (Ford) is recalling certain 2021-2023 Mustang Mach E vehicles. The rear differential pinion shaft may fracture.
Consequence & remedy
Consequence: Differential pinion shaft fracture may result in a loss of drive power, or unintended vehicle movement if the vehicle is in park without the parking brake applied, increasing the risk of a crash.
Remedy: Dealers will repair or replace the rear differential assembly as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed July 13, 2026. Additional letters will be sent once the remedy is available, anticipated in late December 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S50.
Aug 8, 2025
Ford Motor Company (Ford) is recalling certain 2021 Mach-E vehicles that were repaired incorrectly under recall 24V777. An Over-The-Air (OTA) update to the Anti-lock Braking System (ABS) may result in a loss of power brake assist, ABS, Electronic Stability Control, Traction Control, and driver assistance features.
Consequence & remedy
Consequence: A loss of power brake assist can increase the distance required to stop the vehicle. Additionally, a disabled antilock brake system and/or stability control system can result in a loss of vehicle control. Either of these scenarios can increase the risk of a crash.
Remedy: Dealers will update the ABS calibration software, free of charge. Owner notification letters were mailed September 18, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S81.
Jun 13, 2025
Ford Motor Company (Ford) is recalling certain 2021-2025 Mustang Mach E vehicles. In the event of a low battery charge, the electronic door latches may remain locked once the driver or front passenger exits and shuts the door, possibly trapping someone who is unable to use the inside door release handles, such as a child in the back seat.
Consequence & remedy
Consequence: The inability to enter or exit the vehicle in an emergency increases the risk of injury.
Remedy: Dealers will update the Powertrain Control Module (PCM) and the Secondary On-Board Diagnostic Control Module C (SOBDMC) software, free of charge. Owner notification letters were mailed to 2021-2025 Mustang Mach-E owners September 12, 2025. Additionally, Owner notification letters were mailed to 2024-2025 Mustang Mach-E owners July 10, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S65.
Additional source detail variants (2)
Electrical System:body Control Module:software
Ford Motor Company (Ford) is recalling certain 2021-2025 Mustang Mach E vehicles. In the event of a low battery charge, the electronic door latches may remain locked once the driver or front passenger exits and shuts the door, possibly trapping someone who is unable to use the inside door release handles, such as a child in the back seat.
Consequence: The inability to enter or exit the vehicle in an emergency increases the risk of injury.
Remedy: Dealers will update the Powertrain Control Module (PCM) and the Secondary On-Board Diagnostic Control Module C (SOBDMC) software, free of charge. Owner notification letters were mailed to 2021-2025 Mustang Mach-E owners September 12, 2025. Additionally, Owner notification letters were mailed to 2024-2025 Mustang Mach-E owners July 10, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S65.
Latches/locks/linkages:doors:latch
Ford Motor Company (Ford) is recalling certain 2021-2025 Mustang Mach E vehicles. In the event of a low battery charge, the electronic door latches may remain locked once the driver or front passenger exits and shuts the door, possibly trapping someone who is unable to use the inside door release handles, such as a child in the back seat.
Consequence: The inability to enter or exit the vehicle in an emergency increases the risk of injury.
Remedy: Dealers will update the Powertrain Control Module (PCM) and the Secondary On-Board Diagnostic Control Module C (SOBDMC) software, free of charge. Owner notification letters were mailed to 2021-2025 Mustang Mach-E owners September 12, 2025. Additionally, Owner notification letters were mailed to 2024-2025 Mustang Mach-E owners July 10, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S65.
May 9, 2025
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to delay, freeze, or not display when the vehicle is in reverse.
Consequence & remedy
Consequence: A frozen or missing rearview camera image can reduce the driver's view behind the vehicle, increasing the risk of a crash.
Remedy: The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49.
Feb 28, 2025
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles previously repaired incorrectly under recall number 22V-412. The high voltage battery main contactors may overheat.
Consequence & remedy
Consequence: An overheated high voltage battery contactor may cause the vehicle to lose drive power, increasing the risk of a crash.
Remedy: Dealers will update the on-board software, free of charge. Owner notification letters were mailed April 11, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S14.
Oct 18, 2024
Ford Motor Company (Ford) is recalling certain 2021 Mach-E vehicles. An Over-The-Air (OTA) update to the Anti-lock Braking System (ABS) may result in a loss of power brake assist, ABS, Electronic Stability Control, Traction Control, and driver assistance features.
Consequence & remedy
Consequence: A loss of power brake assist can extend the distance required to stop the vehicle. Additionally, a disabled antilock brake system and/or stability control system can result in a loss of vehicle control. Either of these scenarios can increase the risk of a crash.
Remedy: Dealers will update the ABS calibration, free of charge. Owner notification letters were mailed November 5, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S65.
Oct 13, 2023
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles equipped with an extended range battery. The high voltage battery main contactors may overheat.
Consequence & remedy
Consequence: An overheated high voltage battery contactor can result in a loss of drive power, increasing the risk of a crash.
Remedy: Dealers will replace the high voltage battery junction box, free of charge. Owner notification letters were mailed December 29, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S56. Vehicles included in this recall that were previously repaired under recall 22V-412 will need to have the new remedy completed.
Jun 10, 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E vehicles. The high voltage battery main contactors may overheat.
Consequence & remedy
Consequence: An overheated high voltage battery contactor may cause the vehicle to lose drive power, increasing the risk of a crash.
Remedy: Dealers will update the on-board software, free of charge. Owner notification letters were mailed on July 8, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S41.
May 13, 2022
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles equipped with all-wheel drive. The powertrain control module (PCM) functional safety software may fail to detect a software error, resulting in unintended acceleration, unintended deceleration, or a loss of drive power.
Consequence & remedy
Consequence: Unintended acceleration, unintended deceleration, or a loss of drive power increases the risk of a crash.
Remedy: The PCM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed June 9, 2022. Owners may contact Ford customer service at 1-800-436-7332. Ford's number for this recall is 22S29.
Additional source detail variants (2)
Power Train:automatic Transmission:control Module:software
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles equipped with all-wheel drive. The powertrain control module (PCM) functional safety software may fail to detect a software error, resulting in unintended acceleration, unintended deceleration, or a loss of drive power.
Consequence: Unintended acceleration, unintended deceleration, or a loss of drive power increases the risk of a crash.
Remedy: The PCM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed June 9, 2022. Owners may contact Ford customer service at 1-800-436-7332. Ford's number for this recall is 22S29.
Vehicle Speed Control
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles equipped with all-wheel drive. The powertrain control module (PCM) functional safety software may fail to detect a software error, resulting in unintended acceleration, unintended deceleration, or a loss of drive power.
Consequence: Unintended acceleration, unintended deceleration, or a loss of drive power increases the risk of a crash.
Remedy: The PCM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed June 9, 2022. Owners may contact Ford customer service at 1-800-436-7332. Ford's number for this recall is 22S29.
Dec 16, 2021
Ford Motor Company (Ford) is recalling certain 2021-2022 Mustang Mach-E and 2022 Maverick vehicles. The rear seat belt buckles may not be properly attached to the rear floor assembly. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 208, "Occupant Crash Protection," and 210, "Seat Belt Assembly Anchorages."
Consequence & remedy
Consequence: Improperly attached seat belts may not adequately restrain an occupant in a crash, increasing the risk of injury.
Remedy: Dealers will repair the rear seat belt buckle attachments, free of charge. Owner notification letters were mailed January 28, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C36.
Sep 14, 2021
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 212, "Windshield Mounting."
Consequence & remedy
Consequence: A windshield that separates from a vehicle during a crash can increase the risk of injury.
Remedy: Dealers will remove and reinstall the windshield, free of charge. Owner notification letters were mailed on October 29, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C22.
Additional source detail variants (2)
Visibility:windshield:critical Fasteners
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 212, "Windshield Mounting."
Consequence: A windshield that separates from a vehicle during a crash can increase the risk of injury.
Remedy: Dealers will remove and reinstall the windshield, free of charge. Owner notification letters were mailed on October 29, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C22.
Visibility:windshield
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 212, "Windshield Mounting."
Consequence: A windshield that separates from a vehicle during a crash can increase the risk of injury.
Remedy: Dealers will remove and reinstall the windshield, free of charge. Owner notification letters were mailed on October 29, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C22.
Sep 14, 2021
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles. The vehicle's panoramic roof glass panel may not have been properly bonded to the vehicle, which could allow it to detach.
Consequence & remedy
Consequence: A roof panel that separates from a vehicle can become a road hazard, increasing the risk of a crash or injury.
Remedy: Dealers will apply additional urethane adhesive, free of charge. Owner notification letters were mailed October 29, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S42.
Mar 5, 2021
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles. The front subframe bolts may not have been tightened properly during assembly, which could result in loose bolts.
Consequence & remedy
Consequence: Loose subframe bolts may reduce the vehicle's performance in a crash, increasing the risk of injury.
Remedy: Ford will notify owners, and dealers will inspect the front subframe bolts and tighten them as necessary, free of charge. The recall began April 2, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S09.
Additional source detail variants (2)
Structure:frame And Members
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles. The front subframe bolts may not have been tightened properly during assembly, which could result in loose bolts.
Consequence: Loose subframe bolts may reduce the vehicle's performance in a crash, increasing the risk of injury.
Remedy: Ford will notify owners, and dealers will inspect the front subframe bolts and tighten them as necessary, free of charge. The recall began April 2, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S09.
Suspension:subframe/mounting Bracket
Ford Motor Company (Ford) is recalling certain 2021 Mustang Mach-E vehicles. The front subframe bolts may not have been tightened properly during assembly, which could result in loose bolts.
Consequence: Loose subframe bolts may reduce the vehicle's performance in a crash, increasing the risk of injury.
Remedy: Ford will notify owners, and dealers will inspect the front subframe bolts and tighten them as necessary, free of charge. The recall began April 2, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S09.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4EA25001 · Collisions Involving Ford Bluecruise
Opened Jan 17, 2025 · No close date supplied
Status: open (inferred from source dates) · Electrical System:adas
On April 25, 2024, NHTSA’s Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24012) to assess BlueCruise, a partial driving automation system available on certain vehicles manufactured by Ford Motor Company (Ford). NHTSA opened the investigation after the agency received notice of two fatal collisions involving BlueCruise-equipped Ford Mustang Mach-E vehicles. Based on the incidents, NHTSA scoped the investigation to 2021-2024 Mustang Mach-E vehicles equipped with BlueCruise. In June 2024, ODI sent an Information Request (IR) letter to Ford requiring that it provide certain information pertaining to crashes, non-crash reports, and technical specifications that relate to BlueCruise, as well as other Ford partial driving automation systems that offer lane and speed maintenance. In its response to ODI’s IR, Ford stated that there are 2,539,962 Ford and Lincoln vehicles (including subject and peer vehicles) equipped with a partial driving automation system within the scope of the request. The majority of these vehicles are equipped with a system that Ford calls Lane Centering Assist (LCA), which is a hands-on partial driving automation system that combines longitudinal control authority governed by Adaptive Cruise Control (ACC) and lateral control authority governed by a steerable path. LCA is offered on a wide range of Ford and Lincoln models beginning in model year 2019. Vehicles that are equipped with BlueCruise, the focus of this investigation, have LCA capability and additionally offer hands-free partial driving automation when certain conditions are met. Hands-free BlueCruise operation is only offered on certain roadways and system availability is geofenced using vehicle GPS. BlueCruise-equipped vehicles employ a camera-based driver monitoring system to determine driver attentiveness to the roadway. BlueCruise was introduced in model year 2021 and is currently available in a select range of Ford and Lincoln vehicles. For BlueCruise- and LCA-equipped vehicles, both ACC and Pre-Collision Assist (PCA) features use a combination of camera and radar sensing technologies to detect and classify objects. ACC is specifically designed to detect vehicles (including cars, trucks, and motorcycles) and bicycles in front of the subject vehicle which are either stationary or moving in the same direction as the subject vehicle. Through this investigation, limitations in the detection of stationary vehicles in certain conditions have been identified. Specifically, due to the potential for false detection of stationary objects at long distances, Ford designed ACC to inhibit any response to reported stationary objects when the subject vehicle’s approach speed is at or above 62 mph. Additionally, system performance may be limited when there is poor visibility due to insufficient illumination. In addition to reviewing Ford’s response to ODI’s IR, the agency conducted a review of crash and non-crash reports identified collectively through Ford’s IR response, incident reporting through Standing General Order 2021-01 (SGO), and NHTSA vehicle owner questionnaires. In total, 32 crashes and 2,004 non-crash reports on subject and peer Ford vehicles were identified across manufacturer and ODI data sources. A detailed analysis of each crash was conducted including the review of any available police reports, photographs, data recovered from in-vehicle event data recorders, connected vehicle data, and/or other information. In both fatal collisions referenced in the PE24012 opening resume, the subject Ford Mustang Mach-E vehicle was traveling over 70 mph on a controlled-access highway during nighttime lighting conditions with hands-free BlueCruise engaged when it collided with a stationary vehicle. Analysis of data imaged from the vehicles’ event data recorders demonstrates that in each incident, the driver did not apply the brakes or take evasive steering action, and no deceleration was initiated by either the BlueCruise system or PCA prior to impact. Through the agency’s crash analysis, four additional frontal collisions were identified where the subject Ford impacted a stopped or slow-moving lead vehicle or another stationary object located in the travel lane. Two of these four incidents involved BlueCruise-equipped Ford Mustang Mach-E vehicles (included in the failure report summary along with the fatal collisions discussed above), while the other two involved other Ford models equipped with the LCA system. Additionally, a trend was identified through analysis of the non-crash reports relating to allegations that ACC (the longitudinal component of both BlueCruise and LCA) failed to detect and/or respond to a stopped or slow-moving lead vehicle. In these reports, consumers often describe that the absence of deceleration initiated by ACC was unexpected and required harsh manual braking or intervention from the PCA to avoid a frontal collision with the lead vehicle. Based on NHTSA’s analysis, system limitations relating to the detection of stationary vehicles while traveling at highway speeds and in nighttime lighting conditions appear to be factors in collisions under investigation and several apparently similar near-miss, non-crash reports. This Engineering Analysis (EA) is being opened to further investigate these system limitations and to evaluate drivers’ ability to respond to scenarios that exceed system limitations. During the EA, the agency expects to, among other things, perform vehicle evaluations, review additional technical information, and perform additional analysis of related crashes and non-crash reports. The crashes included in the failure report summary can be found at NHTSA.gov under the following SGO report identification numbers: 502-7268, 502-7426, 502-6852, 502-8738.
PE24012 · Collisions Involving Ford Bluecruise
Opened Apr 25, 2024 · Closed Jan 17, 2025
Status: closed (inferred from source dates) · Electrical System:adas
On April 25, 2024, NHTSA’s Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24012) to assess BlueCruise, a partial driving automation system available on certain vehicles manufactured by Ford Motor Company (Ford). NHTSA opened the investigation after the agency received notice of two fatal collisions involving BlueCruise-equipped Ford Mustang Mach-E vehicles. Based on the incidents, NHTSA scoped the investigation to 2021-2024 Mustang Mach-E vehicles equipped with BlueCruise. In June 2024, ODI sent an Information Request (IR) letter to Ford requiring that it provide certain information pertaining to crashes, non-crash reports, and technical specifications that relate to BlueCruise, as well as other Ford partial driving automation systems that offer lane and speed maintenance. In its response to ODI’s IR, Ford stated that there are 2,539,962 Ford and Lincoln vehicles (including subject and peer vehicles) equipped with a partial driving automation system within the scope of the request. The majority of these vehicles are equipped with a system that Ford calls Lane Centering Assist (LCA), which is a hands-on partial driving automation system that combines longitudinal control authority governed by Adaptive Cruise Control (ACC) and lateral control authority governed by a steerable path. LCA is offered on a wide range of Ford and Lincoln models beginning in model year 2019. Vehicles that are equipped with BlueCruise, the focus of this investigation, have LCA capability and additionally offer hands-free partial driving automation when certain conditions are met. Hands-free BlueCruise operation is only offered on certain roadways and system availability is geofenced using vehicle GPS. BlueCruise-equipped vehicles employ a camera-based driver monitoring system to determine driver attentiveness to the roadway. BlueCruise was introduced in model year 2021 and is currently available in a select range of Ford and Lincoln vehicles. For BlueCruise- and LCA-equipped vehicles, both ACC and Pre-Collision Assist (PCA) features use a combination of camera and radar sensing technologies to detect and classify objects. ACC is specifically designed to detect vehicles (including cars, trucks, and motorcycles) and bicycles in front of the subject vehicle which are either stationary or moving in the same direction as the subject vehicle. Through this investigation, limitations in the detection of stationary vehicles in certain conditions have been identified. Specifically, due to the potential for false detection of stationary objects at long distances, Ford designed ACC to inhibit any response to reported stationary objects when the subject vehicle’s approach speed is at or above 62 mph. Additionally, system performance may be limited when there is poor visibility due to insufficient illumination. In addition to reviewing Ford’s response to ODI’s IR, the agency conducted a review of crash and non-crash reports identified collectively through Ford’s IR response, incident reporting through Standing General Order 2021-01 (SGO), and NHTSA vehicle owner questionnaires. In total, 32 crashes and 2,004 non-crash reports on subject and peer Ford vehicles were identified across manufacturer and ODI data sources. A detailed analysis of each crash was conducted including the review of any available police reports, photographs, data recovered from in-vehicle event data recorders, connected vehicle data, and/or other information. In both fatal collisions referenced in the PE24012 opening resume, the subject Ford Mustang Mach-E vehicle was traveling over 70 mph on a controlled-access highway during nighttime lighting conditions with hands-free BlueCruise engaged when it collided with a stationary vehicle. Analysis of data imaged from the vehicles’ event data recorders demonstrates that in each incident, the driver did not apply the brakes or take evasive steering action, and no deceleration was initiated by either the BlueCruise system or PCA prior to impact. Through the agency’s crash analysis, four additional frontal collisions were identified where the subject Ford impacted a stopped or slow-moving lead vehicle or another stationary object located in the travel lane. Two of these four incidents involved BlueCruise-equipped Ford Mustang Mach-E vehicles (included in the failure report summary along with the fatal collisions discussed above), while the other two involved other Ford models equipped with the LCA system. Additionally, a trend was identified through analysis of the non-crash reports relating to allegations that ACC (the longitudinal component of both BlueCruise and LCA) failed to detect and/or respond to a stopped or slow-moving lead vehicle. In these reports, consumers often describe that the absence of deceleration initiated by ACC was unexpected and required harsh manual braking or intervention from the PCA to avoid a frontal collision with the lead vehicle. Based on NHTSA’s analysis, system limitations relating to the detection of stationary vehicles while traveling at highway speeds and in nighttime lighting conditions appear to be factors in collisions under investigation and several apparently similar near-miss, non-crash reports. This Preliminary Evaluation is being upgraded to an Engineering Analysis (EA25001) to further investigate these system limitations and to evaluate drivers’ ability to respond to scenarios that exceed system limitations. During the EA, the agency expects to, among other things, perform vehicle evaluations, review additional technical information, and perform additional analysis of related crashes and non-crash reports. The crashes included in the failure report summary can be found at NHTSA.gov under the following SGO report identification numbers: 502-7268, 502-7426, 502-6852, 502-8738.
RQ23004 · High Voltage Battery Contactor Failure
Opened Aug 17, 2023 · Closed Dec 6, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System:traction Battery:management System/energy Control Module (bms/becm):software; Engine And Engine Cooling:engine:engine Control Module (ecu/ecm):software
On August 17, 2023, the Office of Defects Investigations (ODI) opened RQ23-004 to investigate instances of loss of motor power due to overheating high voltage battery contactors in model year (MY) 2021-2022 Ford Mustang Mach-E vehicles (subject vehicles). This Recall Query (RQ) was opened after receiving 12 consumer complaints alleging a high voltage battery main contactor failure in subject vehicles that were included in Recall 22V-412 and remedied prior to the reported incidents. The remedy in 22V-412 was a Secondary On-Board Diagnostic Control Module (SOBDMC) software update to monitor contactor temperature and reduce battery power to prevent damage to the contactor, and a Battery Energy Control Module (BECM) software update to monitor contactor resistance to identify an overheated contactor and reduce vehicle power to prevent further damage. On October 13, 2023, Ford filed Recall 23V-687 of 34,762 2021-2022 Ford Mustang Mach-E vehicles produced from May 27, 2020 to May 24, 2022 with recalled Bussed Electrical Center parts NK48-10C666-AA, NK48-10C666-BA, or LK98-10C666-AB. Affected vehicles are equipped with the extended range battery. Ford stated that preexisting damage to the contactors caused by heat and accumulated wear may reduce the effectiveness of the software update remedy in 22V-412. The remedy of 23V-687 is to complete a replacement of the Bussed Electrical Center, or High Voltage Battery Junction Box. In addition, Ford stated that subject vehicles equipped with standard range batteries, in comparison to vehicles equipped with extended range batteries, are less at risk of experiencing this failure due to their smaller battery capacity and lower output electric drive motors. In view of the recall action taken by Ford, ODI is closing this investigation. ODI will continue to monitor reports of this failure in both extended range and standard range models. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Electrical System:propulsion System:traction Battery:management System/energy Control Module (bms/becm):software
On August 17, 2023, the Office of Defects Investigations (ODI) opened RQ23-004 to investigate instances of loss of motor power due to overheating high voltage battery contactors in model year (MY) 2021-2022 Ford Mustang Mach-E vehicles (subject vehicles). This Recall Query (RQ) was opened after receiving 12 consumer complaints alleging a high voltage battery main contactor failure in subject vehicles that were included in Recall 22V-412 and remedied prior to the reported incidents. The remedy in 22V-412 was a Secondary On-Board Diagnostic Control Module (SOBDMC) software update to monitor contactor temperature and reduce battery power to prevent damage to the contactor, and a Battery Energy Control Module (BECM) software update to monitor contactor resistance to identify an overheated contactor and reduce vehicle power to prevent further damage. On October 13, 2023, Ford filed Recall 23V-687 of 34,762 2021-2022 Ford Mustang Mach-E vehicles produced from May 27, 2020 to May 24, 2022 with recalled Bussed Electrical Center parts NK48-10C666-AA, NK48-10C666-BA, or LK98-10C666-AB. Affected vehicles are equipped with the extended range battery. Ford stated that preexisting damage to the contactors caused by heat and accumulated wear may reduce the effectiveness of the software update remedy in 22V-412. The remedy of 23V-687 is to complete a replacement of the Bussed Electrical Center, or High Voltage Battery Junction Box. In addition, Ford stated that subject vehicles equipped with standard range batteries, in comparison to vehicles equipped with extended range batteries, are less at risk of experiencing this failure due to their smaller battery capacity and lower output electric drive motors. In view of the recall action taken by Ford, ODI is closing this investigation. ODI will continue to monitor reports of this failure in both extended range and standard range models. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine And Engine Cooling:engine:engine Control Module (ecu/ecm):software
On August 17, 2023, the Office of Defects Investigations (ODI) opened RQ23-004 to investigate instances of loss of motor power due to overheating high voltage battery contactors in model year (MY) 2021-2022 Ford Mustang Mach-E vehicles (subject vehicles). This Recall Query (RQ) was opened after receiving 12 consumer complaints alleging a high voltage battery main contactor failure in subject vehicles that were included in Recall 22V-412 and remedied prior to the reported incidents. The remedy in 22V-412 was a Secondary On-Board Diagnostic Control Module (SOBDMC) software update to monitor contactor temperature and reduce battery power to prevent damage to the contactor, and a Battery Energy Control Module (BECM) software update to monitor contactor resistance to identify an overheated contactor and reduce vehicle power to prevent further damage. On October 13, 2023, Ford filed Recall 23V-687 of 34,762 2021-2022 Ford Mustang Mach-E vehicles produced from May 27, 2020 to May 24, 2022 with recalled Bussed Electrical Center parts NK48-10C666-AA, NK48-10C666-BA, or LK98-10C666-AB. Affected vehicles are equipped with the extended range battery. Ford stated that preexisting damage to the contactors caused by heat and accumulated wear may reduce the effectiveness of the software update remedy in 22V-412. The remedy of 23V-687 is to complete a replacement of the Bussed Electrical Center, or High Voltage Battery Junction Box. In addition, Ford stated that subject vehicles equipped with standard range batteries, in comparison to vehicles equipped with extended range batteries, are less at risk of experiencing this failure due to their smaller battery capacity and lower output electric drive motors. In view of the recall action taken by Ford, ODI is closing this investigation. ODI will continue to monitor reports of this failure in both extended range and standard range models. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
Illustration