IllustrationDRIVING ON HIGHWAY AT 65 MILES WENT CAR WOULD LOSE POWER AND COULDN'T ACCELERATE AND CAR STARTED TO SHAKE WHEN CAME TO A STOP, CUT CAR OFF, WAITED A MIN, CUT CAR ON, TOOK A COUPLE EXTRA CRANKS BEFORE TURNING OVER, AND CAR WORKED FINE THIS HAD HAPPENED 3 TIMES AND IS VERY RANDOM AND DANGEROUS. *TR
2011 Ford Fusion
Owner reports · Recalls · Investigations
More warning signs than most Fusion years
Owner complaints for the 2011 Ford Fusion are substantially higher than the model-year median of 1,109.
About this comparison →How this year compares
Owner complaints by model year
Compare all Fusion years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1720–25K
43925–50K
47850–75K
34375–100K
422100–150K
235150K+
2,089 reports with mileage · 696 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 1,428 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 330 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 276 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
80 crash reports10 fire reports37 injury reports
Power Train complaints
268 reportsAS WE WERE DRIVING IN THE FREEWAY AT ABOUT 70 MPH ON APRIL 7TH 2013, THE CAR LOST POWER AND STALLED OUT IN THE MIDDLE LANE OF THE FREEWAY. AT THAT EXACT MOMENT THE CAR FELT LIKE IT JERKED HARD AND THEN STALLED AND THE LIGHT WITH THE WRENCH SYMBOL CAME ON IN THE DASHBOARD. THEN IT IMMEDIATELY DISAPPEARED AFTER BEING ON WHEN THE C…
Read full complaint
AS WE WERE DRIVING IN THE FREEWAY AT ABOUT 70 MPH ON APRIL 7TH 2013, THE CAR LOST POWER AND STALLED OUT IN THE MIDDLE LANE OF THE FREEWAY. AT THAT EXACT MOMENT THE CAR FELT LIKE IT JERKED HARD AND THEN STALLED AND THE LIGHT WITH THE WRENCH SYMBOL CAME ON IN THE DASHBOARD. THEN IT IMMEDIATELY DISAPPEARED AFTER BEING ON WHEN THE CAR JERKED AND STALLED. MANAGE TO PUT HAZZARD LIGHTS ON AND MAKE IT SAFELY TO THE FREEWAY SHOULDER WHERE THE CAR AFTER A COUPLE OF MINUTES TRYING AND WAITING STARTED AGAIN AS IF NOTHING HAPPENED. AFTER TURNING THE CAR OFF THE CAR WOULD NOT TURN BACK ON AND SOUNDED LIKE THE ENGINE WAS STRUGGLING TO KEEP UP AFTER THE CAR WAS JUMP STARTED. THE CAR THEN WAS MAKING SOUNDS IN THE ENGINE BAY AND MANAGED TO MAKE IT TO A GAS STATION COUPLE FEET AWAY AND THE CAR DIED AGAIN AFTER TURNING IT OFF TO REFUEL ONCE AGAIN HAD TO GET THE CAR JUMP STARTED. CAR ONCE AGAIN STARTED TO FEEL AND SOUND AS IF IT WAS STRUGGLING TO STAY STABLE. HAD THE CAR TOWED THE NEXT MORNING TO LOCAL FORD DEALERSHIP WHERE THEY REPLACED THE BATTERY AND INSTALL A NEW THROTTLE BOX. COMPUTER CODE AT DEALERSHIP DETERMINED CAUSE OF PROBLEM WAS DUE TO FAULTY THROTTLE BOX. *TR
CAR STARTED ROUGH, HAD VERY LITTLE POWER WHEN PULLING OUT OF GARAGE AND THE WRENCH LIGHT CAME ON. I COULD HARDLY MAKE IT TO THE NEXT DRIVE. PUT IN REVERSE AND PUT CAR BACK IN GARAGE. WHEN I TOOK IT INTO FORD FOR SERVICE THERE WERE NO CODES BUT THEY UPDATED THE COMPUTER HOPING IT WOULD FIX THE GLITCH. ON APRIL 4, 2011 IT HAPPE…
Read full complaint
CAR STARTED ROUGH, HAD VERY LITTLE POWER WHEN PULLING OUT OF GARAGE AND THE WRENCH LIGHT CAME ON. I COULD HARDLY MAKE IT TO THE NEXT DRIVE. PUT IN REVERSE AND PUT CAR BACK IN GARAGE. WHEN I TOOK IT INTO FORD FOR SERVICE THERE WERE NO CODES BUT THEY UPDATED THE COMPUTER HOPING IT WOULD FIX THE GLITCH. ON APRIL 4, 2011 IT HAPPENED AGAIN. THIS TIME I WAS STOPPED AT A LIGHT ON A HIGHWAY WHEN I GAVE IT GAS IT STARTED FORWARD, THE WRENCH LIGHT CAME ON AND ONCE AGAIN LITTLE TO NO POWER WHEN PRESSING ON THE ACCELERATOR. (I WAS LUCKY TO NOT GET REAR-ENDED.) I OUT ON THE HAZARDS AND SLOWLY COASTED INTO A PARKING LOT. I CALLED FORD AND HAD IT TOWED BACK TO THE DEALER. THIS TIME IT THREW CODES SO THEY WERE ABLE TO DETERMINE THE ISSUE WHICH WAS THE THROTTLE BODY AND IT WAS REPLACED. (THANKFULLY THIS WAS ALL UNDER WARRANTY.) THIS IS A VERY DANGEROUS ISSUE. I WAS 3 LIGHTS AWAY FROM GETTING ONTO THE INTERSTATE DURING RUSH HOUR TRAFFIC. I HATE TO THINK WHAT WOULD HAVE HAPPENED IF THIS HAD OCCURRED ON THE INTERSTATE. *TR
WHILE DRIVING ON CRUISE CONTROL APPROXIMATELY 70 MPH, THE CAR LOST ALL ACCELERATION. THE ENGINE IS 4 CYL. ENGINE LIGHT CAME ON. COASTED TO RIGHT OF FREEWAY AND CAME TO A STOP. TURNED IGNITION KEY TO OFF AND THEN RESTARTED CAR. PLACED IN DRIVE AND DROVE AND ACCELERATED FINE THERE AFTER. *TR
I WAS GOING THROUGH A SCHOOL ZONE ON MY WAY TO WORK. WHEN I REACHED THE END OF SCHOOL ZONE I ATTEMPTED TO ACCELERATE BUT THE ENGINE WOULD NOT. THERE WAS NO THROTTLE RESPONSE AND THE ENGINE WAS IN A VERY ROUGH IDLE. I PULLED OVER, SHUT THE CAR OFF, WAITED ABOUT 5 MIN AND STARTED IT BACK UP. ON START-UP, THE ENGINE CRANKED A FEW …
Read full complaint
I WAS GOING THROUGH A SCHOOL ZONE ON MY WAY TO WORK. WHEN I REACHED THE END OF SCHOOL ZONE I ATTEMPTED TO ACCELERATE BUT THE ENGINE WOULD NOT. THERE WAS NO THROTTLE RESPONSE AND THE ENGINE WAS IN A VERY ROUGH IDLE. I PULLED OVER, SHUT THE CAR OFF, WAITED ABOUT 5 MIN AND STARTED IT BACK UP. ON START-UP, THE ENGINE CRANKED A FEW EXTRA TIMES BEFORE IT FINALLY TURNED OVER. I WAS ABLE TO DRIVE AGAIN AFTER THAT BUT NOTICED THAT THE RPMS JUMPED AROUND WHEN I WAS IN THIRD GEAR BETWEEN 1500-2000 RPM. SEEING THE RPMS JUMP AROUND LIKE THAT MADE ME THINK THAT THE ENGINE WAS GOING TO LOSE POWER AGAIN, AS IT IS CHARACTERISTIC OF THIS PROBLEM. THIS IS THIRD TIME THIS HAS HAPPENED TO THE CAR. *TR
WHILE DRIVING, ENGINE COMPLETELY LOSES POWER AND WRENCH LIGHT ILLUMINATES ON DASHBOARD. PULL OFF OF ROAD AND STOP CAR AND REALLY ROUGH IDLE. TURN ENGINE OFF AND RESTART AND WRENCH LIGHT GOES OUT. ENGINE RUNS FINE AFTER. THIS CONTINUES TO OCCUR ON INTERMITTENT BASIS. SOMETIMES HAPPENS 3-4 TIMES WITHIN ABOUT 10 MILES. OTHER TIMES …
Read full complaint
WHILE DRIVING, ENGINE COMPLETELY LOSES POWER AND WRENCH LIGHT ILLUMINATES ON DASHBOARD. PULL OFF OF ROAD AND STOP CAR AND REALLY ROUGH IDLE. TURN ENGINE OFF AND RESTART AND WRENCH LIGHT GOES OUT. ENGINE RUNS FINE AFTER. THIS CONTINUES TO OCCUR ON INTERMITTENT BASIS. SOMETIMES HAPPENS 3-4 TIMES WITHIN ABOUT 10 MILES. OTHER TIMES IT HAS GONE HUNDREDS OF MILES BETWEEN INCIDENTS. *TR
HAD THE VEHICLE FOR ABOUT A MONTH BUT HAD ONLY DRIVEN IT ABOUT 600 MILES. (FEB. 21, 2013 - 21,700 MILES) MY WIFE WAS DRIVING ALONG A 4 LANE ROAD DOING ABOUT 50 MPH WHEN SHE NOTICED THE CAR SUDDENLY LOSING POWER. SHE WAS IN THE LEFT HAND LANE WITH NO SHOULDER OR ROOM TO MOVE TO THE RIGHT LANE BECAUSE OF TRAFFIC AND WAS ALMO…
Read full complaint
HAD THE VEHICLE FOR ABOUT A MONTH BUT HAD ONLY DRIVEN IT ABOUT 600 MILES. (FEB. 21, 2013 - 21,700 MILES) MY WIFE WAS DRIVING ALONG A 4 LANE ROAD DOING ABOUT 50 MPH WHEN SHE NOTICED THE CAR SUDDENLY LOSING POWER. SHE WAS IN THE LEFT HAND LANE WITH NO SHOULDER OR ROOM TO MOVE TO THE RIGHT LANE BECAUSE OF TRAFFIC AND WAS ALMOST REAR-ENDED BY A DUMP TRUCK WHO HAD NO IDEA SHE WAS RAPIDLY SLOWING DOWN BECAUSE SHE WASN'T PUTTING ON ANY BRAKE TO INDICATE THIS. SHE BROUGHT THE VEHICLE TO A STOP BUT IT WOULD NOT MOVE EVEN WHEN THE GAS PEDAL WAS DEPRESSED. SHE THOUGHT IT HAD STALLED BUT LATER TOLD ME SHE DIDN'T NOTICE ANY DASH LIGHTS ON. SHE TURNED THE KEY OFF AND RESTARTED IT AND IT RAN FINE THE REST OF THE WAY HOME. CALLED FORD DEALERSHIP WHERE IT WAS PURCHASED AND HE ASKED ABOUT ENGINE CODE LIGHTS (OF WHICH NONE WERE SHOWING ). HE SAID WITHOUT A CODE HE COULDN'T DO ANYTHING. ( MARCH 7, 2013 - 22,400 MILES ) TURNING A CORNER FROM A STOP THE CAR ACCELERATED AND THEN LOST POWER, ENGINE SEEMED TO SPUTTER AND RUN ROUGH, PULLED OVER AND STOPPED. WRENCH LIGHT ON DASH WAS ON, DEPRESSED ACCELERATOR PEDAL BUT NOTHING HAPPENED. ENGINE WAS RUNNING BUT TACHOMETER DIDN'T MOVE AT ALL WHEN ACCELERATOR WAS DEPRESSED. TURNED ENGINE OFF, RESTARTED, WRENCH LIGHT WENT OFF AND RAN OK. HAVE ALSO NOTED THAT TRANSMISSION SHIFTING IS NOT ALWAYS SHIFTING AS SMOOTH AS WHEN WE FIRST STARTED DRIVING IT. IT SEEMS TO JUMP OR LURCH IN AT LEAST ONE OF THE GEARS BUT THIS IS JUST AN INTERMITTENT PROBLEM RIGHT NOW. I WILL TAKE NOTE OF THIS AND REPORT BACK. [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR
I WAS DRIVING ON THE HIGHWAY AND I STARTED TO FEEL THE CAR JERK FORWARD SLIGHTLY ABOUT ONCE EVERY TEN SECONDS. ABOUT A MINUTE OR SO LATER I COULD NO LONGER ACCELERATE AND THE AMBER WRENCH LIGHT WAS ILLUMINATED. I COASTED TO A STOP AND PULLED OVER ONTO THE SHOULDER. WHEN I CAME TO A STOP THE RPMS WERE VERY ERRATIC AND BOUNCING BE…
Read full complaint
I WAS DRIVING ON THE HIGHWAY AND I STARTED TO FEEL THE CAR JERK FORWARD SLIGHTLY ABOUT ONCE EVERY TEN SECONDS. ABOUT A MINUTE OR SO LATER I COULD NO LONGER ACCELERATE AND THE AMBER WRENCH LIGHT WAS ILLUMINATED. I COASTED TO A STOP AND PULLED OVER ONTO THE SHOULDER. WHEN I CAME TO A STOP THE RPMS WERE VERY ERRATIC AND BOUNCING BETWEEN 500-1000. I SHUT THE VEHICLE, WAITED A MINUTE, THEN STARTED IT BACK UP. ON START UP THE ENGINE CRANKED A COUPLE MORE TIMES THAN USUAL BUT FINALLY TURNED OVER. THE CAR RAN FINE AND I WAS ABLE TO CONTINUE DRIVING. *TR
WHILE DRIVING AT HIGHWAY SPEED ON AN INCLINE, THE CAR LOST ALL PROPULSION POWER. AFTER SEVERAL SECONDS, THE CHECK ENGINE WRENCH LIGHT TURNED ON AND I PULLED OVER TO THE SIDE. SHUTTING DOWN THE VEHICLE, WAITING 1 MINUTE AND RESTARTING CLEARED THE CHECK ENGINE LIGHT AND RESTORED POWER. THE SAME THING HAPPENED 6 WEEKS LATER, WHILE …
Read full complaint
WHILE DRIVING AT HIGHWAY SPEED ON AN INCLINE, THE CAR LOST ALL PROPULSION POWER. AFTER SEVERAL SECONDS, THE CHECK ENGINE WRENCH LIGHT TURNED ON AND I PULLED OVER TO THE SIDE. SHUTTING DOWN THE VEHICLE, WAITING 1 MINUTE AND RESTARTING CLEARED THE CHECK ENGINE LIGHT AND RESTORED POWER. THE SAME THING HAPPENED 6 WEEKS LATER, WHILE IDLING AT A TRAFFIC LIGHT. AFTER RESTARTING, THE SYSTEM FAILED AGAIN 2 MINUTES LATER WHILE DRIVING ON LEVEL ROAD AT 15 MPH. THE CAR RESTED FOR 2 HOURS AND WAS THEN DRIVEN WITHOUT INCIDENT TO THE DEALER FOR REPAIRS. THE SERVICE TECHNICIAN PERFORMED EEC TEST, PPT AND COMPONENT TESTS, THEN REPLACED THE THROTTLE BODY. NO SUBSEQUENT INCIDENTS AFTER 1 WEEK. *TR
WHILE DRIVING TO WORK ONE DAY MY CAR SHUT OFF RIGHT AFTER A TURN GOING DOWN A HILL, THE DASH WAS ILLUMINATED AND NO LIGHTS WERE ON OTHER THAN THE DASH. I PUT THE CAR INTO PARK AND TURNED IT OFF THEN STARTED IT RIGHT BACK UP, IT RAN FINE AFTER THAT. THERE IS ANOTHER ISSUE AS WELL THOUGH, WHILE DRIVING IT HESITATED BY SHIFTING AT …
Read full complaint
WHILE DRIVING TO WORK ONE DAY MY CAR SHUT OFF RIGHT AFTER A TURN GOING DOWN A HILL, THE DASH WAS ILLUMINATED AND NO LIGHTS WERE ON OTHER THAN THE DASH. I PUT THE CAR INTO PARK AND TURNED IT OFF THEN STARTED IT RIGHT BACK UP, IT RAN FINE AFTER THAT. THERE IS ANOTHER ISSUE AS WELL THOUGH, WHILE DRIVING IT HESITATED BY SHIFTING AT HIGHER RPM'S THAN IT SHOULD AND TOOK IT TO DEALER ON MONDAY FEBRUARY 25, 2013 AND THEY STILL HAVE IT WITH NO EXPLANATION AS TO WHY IT DID ANY OF THOSE THINGS THAT I MENTIONED. THE ONLY THING THAT THE SERVICE GUY SAYS IS "WELL UNTIL IT IS BILLED OUT I DO NOT KNOW WHAT IS GOING ON WITH THE CAR." I AM VERY FRUSTRATED AND JUST BOUGHT THIS CERTIFIED PRE OWNED TWO WEEKS AGO. THERE SHOULD BE A LEMON LAW ON CERTIFIED PRE OWNED CARS, THIS IS NOT COOL. IT HAS CAUSED A HEADACHE FOR ME AND NOW I AM STUCK PAYING FOR A CAR I CANNOT EVEN DRIVE RIGHT NOW. *TR
Official recalls
721V158000 · Air Bags:frontal:driver Side:inflator Module
Mar 10, 2021
Ford Motor Company (Ford) is recalling certain 2007-2011 Ranger, 2006-2012 Fusion, Lincoln Zephyr, Lincoln MKZ, 2006-2011 Mercury Milan, 2007-2010 Ford Edge, and Lincoln MKX vehicles. The driver's side air bag inflator may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will replace the driver-side airbag inflator or module with an alternate one, free of charge. Owner notification letters were mailed on April 9, 2021 for the passenger side, and November 14, 2022 for the driver side. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S12.
21V081000 · Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
Feb 16, 2021
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Additional source detail variants (3)
Air Bags:frontal:passenger Side:inflator Module
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Air Bags:frontal:driver Side:inflator Module
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Air Bags:frontal
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
19V001000 · Air Bags:frontal:passenger Side:inflator Module
Jan 7, 2019
Ford Motor Company (Ford) is recalling certain 2014 Ford Mustang vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is recalling certain 2011 Ford Ranger and Mercury Milan vehicles, 2011-2012 Ford Fusion and Lincoln Zephyr/MKZ vehicles and 2011-2014 Ford Mustang vehicles sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Ford is also recalling certain 2010 Ford Edge and Lincoln MKX vehicles, 2010-2011 Ford Ranger and Mercury Milan vehicles, 2010-2012 Ford Fusion and Lincoln Zephyr/MKZ vehicles, and 2010-2014 Ford Mustang vehicles sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 13, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall 19S01.
16V384000 · Air Bags:frontal:passenger Side:inflator Module
May 31, 2016
Ford Motor Company (Ford) is recalling certain model year 2007-2011 Ford Ranger vehicles, 2006-2011 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2007-2010 Ford Edge, Lincoln MKX vehicles, 2005-2006 Ford GT vehicles, and 2005-2011 Ford Mustang vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Ford is recalling certain model year 2007-2008 Ford Ranger, Edge and Lincoln MKX vehicles, 2006-2008 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2005-2006 Ford GT vehicles and 2005-2008 Ford Mustang vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Any vehicle not included in "Zone A", or "Zone B" is not included in the safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Ford mailed interim letters informing owners that parts are not yet available on July 15, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
15V793000 · Fuel System, Gasoline:storage:auxillary Tank
Nov 24, 2015
Ford Motor Company (Ford) is recalling certain model year 2010-2011 Ford Fusion vehicles manufactured July 21, 2008, to March 4, 2011, and 2010-2011 Mercury Milan vehicles manufactured July 23, 2008, to December 10, 2010. The affected vehicles have fuel vapor canisters whose purge valves may not operate properly resulting in abnormal pressure changes in the fuel tank.
Consequence & remedy
Consequence: The pressure changes may cause the tank to crack and leak fuel. A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy: Ford will notify owners, and dealers will update the vehicle powertrain control modules and inspect the vehicle for any diagnostic trouble codes (DTCs) for this issue and perform a leak test on the Canister Purge Valve (CPV). The fuel tank will be inspected for cracks. The CPV and fuel tank will be replaced as necessary. These repairs will be performed free of charge. The recall began on January 15, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S34.
15V340000 · Steering:electric Power Assist System
Jun 2, 2015
Ford Motor Company (Ford) is recalling certain model year 2011-2012 Ford Fusion vehicles without a 3.5L engine and Lincoln MKZ hybrid electric vehicles, 2011 Mercury Milan vehicles, 2011-2012 Ford Taurus, Ford Flex, Lincoln MKS, and Lincoln MKT vehicles equipped with a 3.5L GTDI engine and 2013 Ford Taurus, Ford Flex, Lincoln MKS, and Lincoln MKT vehicles equipped with any available engine. The affected vehicles have electric power steering assist systems that may shut down as a result of a steering motor sensor fault.
Consequence & remedy
Consequence: If the vehicle experiences a loss of power steering assist, extra steering effort will be required at lower speeds, increasing the risk of a vehicle crash.
Remedy: Ford will notify owners, and dealers will check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTC). If dealers find any loss of steering assist DTCs, the steering gear will be replaced, free of charge. If, no codes are found during the PSCM inspection, the PSCM software will be updated, free of charge. The recall began on July 21, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S18.
11V574000 · Wheels:lugs/nuts/bolts/studs
Dec 7, 2011
FORD IS RECALLING CERTAIN MODEL YEAR 2010-2011 FORD FUSION AND MERCURY MILAN VEHICLES EQUIPPED WITH 17 INCH STEEL WHEELS AND BUILT FROM APRIL 1, 2009, THROUGH APRIL 30, 2009, AND FROM DECEMBER 1, 2009, THROUGH NOVEMBER 13, 2010. THE WHEEL STUDS MAY FRACTURE, POTENTIALLY CAUSING A WHEEL TO SEPARATE.
Consequence & remedy
Consequence: WHILE DRIVING, MULTIPLE STUD FRACTURES COULD OCCUR AT THE WHEEL LOCATION, AND THE OPERATOR MAY EXPERIENCE VEHICLE VIBRATION AND/OR WHEEL SEPARATION, INCREASING THE RISK OF A CRASH.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT THE REAR BRAKE DISC SURFACE FOR FLATNESS AND REPLACE THE DISCS AS NECESSARY. ADDITIONALLY, THE WHEEL LUG NUTS WILL BE REPLACED ON ALL FOUR WHEELS. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR ABOUT JANUARY 24, 2012. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4EA17004 · Power Steering Failure
Opened Nov 20, 2017 · Closed Feb 9, 2024
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:rack And Pinion; Steering:rack And Pinion:rack
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (4)
Steering:electric Power Assist System
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering:rack And Pinion
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering:rack And Pinion:rack
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE14030 · Electric Power Steering Failure
Opened Oct 2, 2014 · Closed Sep 10, 2015
Status: closed (inferred from source dates) · Steering:electric Power Assist System
The Office of Defects Investigation (ODI) opened a preliminary evaluation to investigate complaints of the loss of power steering while driving. The subject vehicles are equipped with a rack mounted Electric Power Assisted Steering (EPAS) unit.Some of the complaints alleged that the steering assist failed and resulted in increased steering efforts that contributed to a loss of control and in some cases a crash.The EPAS system was manufactured by TRW Automotive for Ford and was designated as Generation I.These units were first produced and put into vehicle production in July 2008 beginning with the model year (MY) 2010 Ford Fusion and Mercury Milan.The system is comprised of a mechanical steering rack-and-pinion gear with torque sensor, electric assist motor, motor position sensor and a power steering control module (PSCM). The PSCM is self-monitoring and designed to detect faults within the system and can store diagnostic trouble codes (DTCs) if a problem is detected.There are 29 potential DTCs the system can detect.Many of these allow the system to go into reduced-assist steering mode by using the default vehicle speed signal should the live speed signal be lost, if voltage to EPAS system falls below 10.7 or goes above 17 volts, the temperature at the PSCM goes above 105C (221F), or if high friction is detected.Some DTCs will cause the system to go into manual steering mode (no assist). On July 1, 2015, Ford filed a Defect Information Report (DIR) identifying a safety related defect in TRW GEN I EPAS systems installed in some of the subject vehicles (NHTSA Recall 15V-340, Ford No. 15S18).The DIR indicated that intermittent electrical connections caused by quality issues associated with conformal coat contamination and ribbon cable pin misalignment within the steering gear motor may lead to a loss of the motor position sensor signal, resulting in a sudden loss of power assist while driving.The recall covers approximately 393,623 vehicles built from September 2010 through February 2012:2011-12 Fusion built SEP 2010 - FEB 2012; 2011-12 Lincoln MKZ built SEP 2010 - FEB 2012; 2011 Milan built SEP 2010 - DEC 2010; 2011-13 Taurus built SEP 2010 - FEB 2012; 2011-13 Flex with 3.5L GTDI engine built SEP 2010 - FEB 2012; and 2011-13 MKS, MKT with 3.5L GTDI engine built SEP 2010 - FEB 2012.The repair consists of updating the PSCM software to prevent a loss of steering assist while driving. The revised software will provide audible and visual warnings to the driver. If one or more of the following DTCs are stored, C1B00-62, C200B-2F, C200B-61, C200B-62, C200C-2F, C200D-49, U0300-00, U2011-49, U2011-61, U3000-46, U3000-49, U3000-61, U3000-72, U3000-96, P07AE-09, the dealer will replace the EPAS system at no charge to the owner.ODI's analysis of failure data for this PE identified a total of 2,584 complaints to ODI and Ford and 9,967 Ford warranty claims related to the alleged defect.The recalled vehicles account for 1,634 of the complaints and 7,311 of the warranty claims.ODI's analysis identified 40 complaints alleging crashes that may be related to loss of steering assist while driving, 20 of which involved vehicles included in Ford's recall.The information available for the alleged crashes were not sufficient to assess specific causes of the incidents or to verify EPAS malfunctions in each case.Most of the crashes were low-speed impacts with curbs or roadside objects resulting in wheel or minor body damage.None of the injury claims indicated medical attention was required.In addition, statistical modeling of the failure data by NHTSA's National Center for Statistics and Analysis projected 10-year failur
PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
EA12009 · Floor Mat Interference With Accelerator
Opened Dec 12, 2012 · Closed Jun 12, 2014
Status: closed (inferred from source dates) · Vehicle Speed Control; Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Additional source detail variants (2)
Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Vehicle Speed Control
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.