NHTSA owner reports · September 18, 2026 snapshot.
Steering complaints
1,660 reportsClear category filter85,000 miles · Jul 12, 2015
Electrical SystemSteering
FOR MONTHS I HAVE BEEN RESETTING MY CARS "POWER STEERING ASSIST FAULT" BY TURNING MY CAR OFF AND TURNING IT BACK ON AND THE POWER STEERING WOULD SUDDENLY WORK AGAIN. LAST NIGHT MY CAR TOOK A COUPLE TURNS ON AND OFF FOR IT TO WORK WHICH IS THE FIRST TIME IT TOOK MORE THAN ONCE TO RESET. TODAY AFTER CHURCH I TURNED MY CAR ON AND O…
Read full complaint
FOR MONTHS I HAVE BEEN RESETTING MY CARS "POWER STEERING ASSIST FAULT" BY TURNING MY CAR OFF AND TURNING IT BACK ON AND THE POWER STEERING WOULD SUDDENLY WORK AGAIN. LAST NIGHT MY CAR TOOK A COUPLE TURNS ON AND OFF FOR IT TO WORK WHICH IS THE FIRST TIME IT TOOK MORE THAN ONCE TO RESET. TODAY AFTER CHURCH I TURNED MY CAR ON AND OFF 10 TIMES AND IT STILL WOULDN'T RESET SO I WAS FORCED TO DRIVE MY CAR HOME WITH NO POWER STEERING, THINKING ABOUT THE FACT THAT IF A CAR SERVED OR A KID RAN OUT IN FRONT OF ME, I WOULDN'T BE ABLE TO SWERVE TO AVOID THEM. BESIDES THE FACT THAT I CAN'T DRIVE MY CAR TO GET TO AND FROM WORK THIS WAY, I DON'T HAVE 1500 DOLLARS TO FIX A PROBLEM THAT SHOULD BE RECALLED IN MY 2010 FORD FUSION AS WELL AS THE 2011-2012 YEARS. THIS PROBLEM IS OBVIOUSLY A RESULT OF FAULTY EQUIPMENT USED IN MANUFACTURING AND NOT BECAUSE OF THE DRIVER.
NHTSA ODI #10733479
92,000 miles · Jul 7, 2015
Electronic Stability Control (esc)Steering
I WAS DRIVING HOME FROM WORK, HAD TO STOP AND DROP SOME ITEMS OFF FOR MY DAUGHTER AT SUMMER CAMP. WHEN I WAS LEAVING CAMP THE STEERING FELT LIKE IT WANTED TO PULL TO THE RIGHT, A FEW MILES DOWN THE ROAD ALL POWER STEERING WAS LOST. SERVICE ADVANC-TRAC WARNING MESSAGE WAS BEING DISPLAYED ON THE DASH BOARD. I PULLED OVER AT A CONV…
Read full complaint
I WAS DRIVING HOME FROM WORK, HAD TO STOP AND DROP SOME ITEMS OFF FOR MY DAUGHTER AT SUMMER CAMP. WHEN I WAS LEAVING CAMP THE STEERING FELT LIKE IT WANTED TO PULL TO THE RIGHT, A FEW MILES DOWN THE ROAD ALL POWER STEERING WAS LOST. SERVICE ADVANC-TRAC WARNING MESSAGE WAS BEING DISPLAYED ON THE DASH BOARD. I PULLED OVER AT A CONVENIENT STORE TO INVESTIGATE THE PROBLEM, COULD NOT FIND ANYTHING. IT WAS RAINING SO I CAREFULLY DROVE HOME WITHOUT ANY POWER STEERING. TOOK CAR TO LOCAL DEALERSHIP WHERE THEY DIAGNOSED THE PROBLEM AS A RACK& PINION FAILURE, TOTAL COST TO REPAIR $1,641.00. THE DEALER STATED THEY HAD NOT SEEN THIS PROBLEM BEFORE. AFTER A SHORT SEARCH I FOUND HUNDREDS OF SIMILAR PROBLEMS REPORTED. I READ WHERE THIS SAME PROBLEM INITIATED A RECALL ON THE 2011 FORD FUSION, BUT NO HELP REFERENCED TO THE 2010 FORD FUSIONS. IF THEY IDENTIFIED THE DEFECT IN THE 2011 MODELS, SHOULDN'T THEY FIX THE PROBLEM FROM THE PREVIOUS MODELS WITH THE ADVANCE-TRAC SYSTEM. NO DEALER WILL TOUCH THIS VEHICLE WITH ITS DEFECT AS A TRADE-IN, MEANWHILE I'M STILL PAYING ON A CAR THAT I CAN NOT DRIVE SAFELY.
NHTSA ODI #10732360
100,000 miles · Jun 30, 2015
Electrical SystemSteering
I HAVE HAD SAME STERRING ISSUE AS THE 2011 FUSIONS AND WAS TOLD THE ONLY RECORSE WAS TO REPLACE THE WHOLE RACK. AND THE RACK I PUT IN HAD THE SAME ISSUE. THE RECALL NEEDS TO BE EXTENDED TO EVERY CAR AND YEAR THAT HAS THAT TYPE OF UNIT IN IT
NHTSA ODI #10731158
99,500 miles · Jun 27, 2015
Steering
WHILE DRIVING MY 2010 FORD FUSION INTO PARKING LOT, THE SERVICE ADVANCE TRAC WARNING APPEARED. I PARKED AND WENT INTO A STORE. AFTER SHOPPING, I WAS READY TO BACK OUT OF THE PARKING SPACE AND COULDN'T. I HAD NO POWER STEERING AND THE WARNING LIGHT SAID "SERVICE POWER STEERING NOW". I HAD MY YOUNG DAUGHTER AND MY MOTHER WITH …
Read full complaint
WHILE DRIVING MY 2010 FORD FUSION INTO PARKING LOT, THE SERVICE ADVANCE TRAC WARNING APPEARED. I PARKED AND WENT INTO A STORE. AFTER SHOPPING, I WAS READY TO BACK OUT OF THE PARKING SPACE AND COULDN'T. I HAD NO POWER STEERING AND THE WARNING LIGHT SAID "SERVICE POWER STEERING NOW". I HAD MY YOUNG DAUGHTER AND MY MOTHER WITH ME, SO THANK GOD WE WERE ALREADY IN A PARKING LOT AND NOT IN TRAFFIC OR AT A HIGHER SPEED!! (I'M ALSO SO THANKFUL MY NEWLY LICENSED SON WASN'T DRIVING DOWN THE HIGHWAY WHEN THIS HAPPENED.) I HAD TO LEAVE MY CAR THERE SINCE IT'S NOT SAFE TO DRIVE AND CALL FOR A RIDE. I WILL BE TAKING IT FOR SERVICE ON MONDAY, MOST LIKELY BY TOW TRUCK. I HAVE FOUND MANY OTHER CASES ONLINE JUST LIKE MINE WHERE THE EXACT SAME THING HAS HAPPENED. I CAN ALMOST BET THE PROBLEM IS THE POWER STEERING RACK. WITH SO MANY REPORTS, WHY HASN'T FORD ISSUED A RECALL FOR THIS? THIS SEEMS LIKE A VERY EXPENSIVE PROBLEM AND I THINK FORD SHOULD HAVE TO PAY TO HAVE IT FIXED. WHEN I BOUGHT THIS CAR IN 2011, I DID NOT EXPECT TO HAVE TO WORRY ABOUT MAJOR SAFETY ISSUES LIKE THIS. I REALLY THOUGH I WAS GETTING ONE OF THE SAFEST CARS ON THE MARKET, BUT APPARENTLY NOT.
NHTSA ODI #10730771
55,000 miles · Jun 25, 2015
Steering
TL* THE CONTACT OWNS A 2010 FORD FUSION. WHILE DRIVING AT 10 MPH, THE POWER STEERING FAILED. THE INSTRUMENT PANEL INDICATED THAT THE POWER STEERING ASSIST FAILED. THE CONTACT TURNED OFF THE VEHICLE AND RESTARTED THE ENGINE AND THE WARNING INDICATOR DISAPPEARED. THE CONTACT WAS ABLE TO DRIVE NORMALLY FOR ABOUT TWO MORE MILES BEFO…
Read full complaint
TL* THE CONTACT OWNS A 2010 FORD FUSION. WHILE DRIVING AT 10 MPH, THE POWER STEERING FAILED. THE INSTRUMENT PANEL INDICATED THAT THE POWER STEERING ASSIST FAILED. THE CONTACT TURNED OFF THE VEHICLE AND RESTARTED THE ENGINE AND THE WARNING INDICATOR DISAPPEARED. THE CONTACT WAS ABLE TO DRIVE NORMALLY FOR ABOUT TWO MORE MILES BEFORE THE FAILURE RECURRED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 55,000. UPDATED 8/31/15*CN UPDATED 10/30/2017*CN
NHTSA ODI #10730405
55,000 miles · Jun 17, 2015
Steering
THE POWER STEERING FROZE AND I WAS UNABLE TO STEER THE CAR. THE POWER STEERING FAULT INDICATOR CAME ON IN THE DISPLAY AREA. I HAVE EXPERIENCED THIS, BRIEFLY, MANY TIMES RIGHT AFTER STARTING THE CAR. THIS WAS THE FIRST TIME WHILE THE CAR WAS ALREADY IN GEAR. LUCKILY I WAS JUST TRYING TO GET OFF MY DRIVEWAY AT THE TIME.
NHTSA ODI #10725715
117,000 miles · Jun 15, 2015
Power TrainSteering
ADVANCE STEERING SERVICE LIGHT CAME ON, ONCE I STOPPED AND RESTARTED THE CAR HAD NO POWER STEERING. I LET THE CAR DIE AND LET IT RESET ITSELF (BATTERY DISCONNECTED) AND PUT IT BACK TOGETHER STILL NO STEERING WENT TO A SHOP THEY SAW 2 CODES ONE WAS TO DUE WITH THE ELECTRONIC STEERING THE OTHER WAS TRANSMISSION FAILURE DUE TO THE …
Read full complaint
ADVANCE STEERING SERVICE LIGHT CAME ON, ONCE I STOPPED AND RESTARTED THE CAR HAD NO POWER STEERING. I LET THE CAR DIE AND LET IT RESET ITSELF (BATTERY DISCONNECTED) AND PUT IT BACK TOGETHER STILL NO STEERING WENT TO A SHOP THEY SAW 2 CODES ONE WAS TO DUE WITH THE ELECTRONIC STEERING THE OTHER WAS TRANSMISSION FAILURE DUE TO THE THE STEERING CODE ISSUE.
NHTSA ODI #10725359
56,787 miles · Jun 14, 2015
Steering
MY WIFE WAS DRIVING HOME FROM WORK WHEN SUDDENLY SHE EXPERIENCED A LOSS OF POWER STEERING IN HER VEHICLE. AFTER TRYING TO KEEP FROM BEING IN AN ACCIDENT SHE WAS ABLE TO PULL HER 2010 FORD FUSION INTO A PARKING LOT. AFTER SHE TURNED INTO THE PARKING LOT SHE TURNED OFF THE VEHICLE AND LET IT SIT FOR A FEW SECONDS THEN SHE RESTART…
Read full complaint
MY WIFE WAS DRIVING HOME FROM WORK WHEN SUDDENLY SHE EXPERIENCED A LOSS OF POWER STEERING IN HER VEHICLE. AFTER TRYING TO KEEP FROM BEING IN AN ACCIDENT SHE WAS ABLE TO PULL HER 2010 FORD FUSION INTO A PARKING LOT. AFTER SHE TURNED INTO THE PARKING LOT SHE TURNED OFF THE VEHICLE AND LET IT SIT FOR A FEW SECONDS THEN SHE RESTARTED THE VEHICLE AND SHE WAS ABLE TO PROCEED A LITTLE FURTHER. THEN IT HAPPENED FOR A SECOND TIME. ONCE AGAIN SHE TURNED THE IGNITION OFF, LET IT SIT FOR A FEW MOMENTS THEN RESTARTED THE VEHICLE. SHE WAS ABLE TO DRIVE A LITTLE FURTHER UNTIL IT ONCE AGAIN HAPPENED AS SHE WAS TURNING INTO OUR DRIVEWAY. ON THE MORNING OF SATURDAY 6/13/2015 I WENT OUT TO THE VEHICLE AND STARTED IT UP AND TRIED TO BACK IT OUT OF OUR DIVE WAY WHEN THE SERVICE THE ADVANCE TRAC SYSTEM MESSAGE APPEARED. I TURNED THE VEHICLE OFF THE RESTARTED THE VEHICLE AND THEN A DIFFERENT MESSAGE APPEARED. THIS TIME IT WAS THE SERVICE POWER STEERING ASSIST MESSAGE. I THEN TURNED OFF THE VEHICLE AND CONTACTED THE LOCAL FORD DEALER AND WAS TOLD THAT IT WAS A COMMON PROBLEM WITH THE FUSION AND THAT I WOULD NEED TO SCHEDULE AN APPOINTMENT TO HAVE THE POWER STEERING RAC REPLACED AND IT WOULD COST AROUND $1,800 TO REPLACE. I TOLD THE MAN THAT WAS RIDICULOUS FOR A VEHICLE THAT HAS ONLY 56,787 MILES ON IT. I HAVE RESEARCHED THIS AND HAVE FOUND THAT MANY OTHER OWNERS HAVE EXPERIENCED THIS SAME ISSUE. I FEEL THAT THIS IS A MAJOR SAFETY ISSUE AND IF IT WAS NOT FOR MY WIFE'S QUICK THINKING SHE MAY HAVE BEEN INVOLVED IN AN ACCIDENT. PLEASE RESEARCH THIS ISSUE BEFORE IT HAPPENS TO SOMEONE ELSE AND UNFORTUNATELY COST SOMEONE THEIR LIFE. PLEASE FEEL FREE TO CONTACT ME ANYTIME FOR ADDITIONAL INFORMATION.
NHTSA ODI #10725177
55,000 miles · Jun 14, 2015
Steering
WHILE MY WIFE WAS DRIVING HOME FROM WORK ON 6/12 THE POWER STEERING WENT OUT. SHE HAD A VERY DIFFICULT TIME TRYING TO STEER THE CAR. IT HAPPENS TWICE ON HER WAY HOME FIRST TIME NEARLY CAUSED AN ACCIDENT BUT SHE WAS ABLE TO COAST IT INTO AN EMPTY PARKING LOT. SHE TURNED THE CAR OFF AND LET IT SIT FOR A FEW. SHE THEN STARTED IT …
Read full complaint
WHILE MY WIFE WAS DRIVING HOME FROM WORK ON 6/12 THE POWER STEERING WENT OUT. SHE HAD A VERY DIFFICULT TIME TRYING TO STEER THE CAR. IT HAPPENS TWICE ON HER WAY HOME FIRST TIME NEARLY CAUSED AN ACCIDENT BUT SHE WAS ABLE TO COAST IT INTO AN EMPTY PARKING LOT. SHE TURNED THE CAR OFF AND LET IT SIT FOR A FEW. SHE THEN STARTED IT UP AGAIN AND TRIED TO CONTINUE HOME WHEN SHE GOT A BLOCK AWAY IT HAPPENED AGAIN I HAD ONE HELL OF A TIME TRYING TO GET IT TO TURN INTO OUR DRIVEWAY. GOT UP THE NEXT MORNING AS STILL THE SAME ISSUE ADVANCE TRAC NEEDS SEVICED. IF FORD WANTS TO TURN OUT A SUBSTANDARD PART I WON'T BE BUYING ANOTHER FORD PRODUCT AGAIN. NO I'M BEING TO IT NEEDS A NEW RACK AT 55000 MILES AND WILL COST AROUND $1800. THIS IS COMPLETE BS FOR A VEHICLE TO NEED A NEW RACK AT THAT LOW OF MILES. THIS IS VERY DANGEROUS A FORD NEEDS TO HAVE A RECALL FOR THIS ISSUE BEFORE SOMEONE GETS HURT OR CAUSES AN ACCIDENT. IF NOT SOUNDS LIKE I NEED TO CONTACT AN ATTORNEY.
NHTSA ODI #10725130
125,000 miles · Jun 8, 2015
Steering
DRIVING 2010 FORD FUSION SEL V6 HOME AT NIGHT AT AROUND 70 MPH, SUDDENLY MESSAGE CAME UP "ADVANCE TRACK , SERVICE POWER STEERING NOW". WE HAD SEEN THIS MESSAGE BEFORE. THIS IS THE FIFTH OCCURRENCE. THE VEHICLE MAINTAINS ITS STEERING ABILITY (GOING 70 MPH), BUT UPON ARRIVAL AT OUR DESTINATION, AND THE SHUT OFF OF THE ENGINE, A…
Read full complaint
DRIVING 2010 FORD FUSION SEL V6 HOME AT NIGHT AT AROUND 70 MPH, SUDDENLY MESSAGE CAME UP "ADVANCE TRACK , SERVICE POWER STEERING NOW". WE HAD SEEN THIS MESSAGE BEFORE. THIS IS THE FIFTH OCCURRENCE. THE VEHICLE MAINTAINS ITS STEERING ABILITY (GOING 70 MPH), BUT UPON ARRIVAL AT OUR DESTINATION, AND THE SHUT OFF OF THE ENGINE, ALL POWER-STEERING ASSIST IS LOST. THIS HAS HAPPENED FIVE TIMES BEFORE. THE FORD DEALER CAN CLEAR ALL OF THE ERROR MESSAGES AND THE CAR WILL HAVE ITS POWER STEERING ABILITY AGAIN; HOWEVER, WHEN THE FORD MECHANIC DIAGNOSED THE ERROR MESSAGES AND THE PROBLEM, HIS SOLUTION WAS TO REPLACE THE ELECTRICAL RACK AND PINION STEERING ASSIST AT A COST OF $1200 PLUS LABOR. I DECLINED, AS I AM SURE THAT THE PROBLEM WILL RECUR. HOW DO I GET RID OF THIS CAR? HOW CAN I SELL IT AND NOT DECLARE ITS UGLY PERSISTENT PROBLEM?? WHY DOESN'T FORD ACT ON THIS? THE MECHANIC STATED THAT HE DIDN'T KNOW OF ANY OTHER CARS WITH THIS PROBLEM.
NHTSA ODI #10724083
Official recalls
11Mar 10, 2021
Ford Motor Company (Ford) is recalling certain 2007-2011 Ranger, 2006-2012 Fusion, Lincoln Zephyr, Lincoln MKZ, 2006-2011 Mercury Milan, 2007-2010 Ford Edge, and Lincoln MKX vehicles. The driver's side air bag inflator may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will replace the driver-side airbag inflator or module with an alternate one, free of charge. Owner notification letters were mailed on April 9, 2021 for the passenger side, and November 14, 2022 for the driver side. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S12.
Feb 16, 2021
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Additional source detail variants (3)
Air Bags:frontal:passenger Side:inflator Module
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Air Bags:frontal:driver Side:inflator Module
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Air Bags:frontal
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Dec 18, 2019
Ford Motor Company (Ford) is recalling certain 2006-2010 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ vehicles. The valves within the ABS Hydraulic Control Units (HCU) may react with brake fluids containing specific corrosion preventative additives. This reaction may cause the valves to not close properly.
Consequence & remedy
Consequence: If the valves do not properly close, additional brake pedal travel may be required to stop the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will flush the brake system with DOT 4 fluid and install a new brake fluid reservoir cap. In addition, the HCU will be tested to detect a possible stuck valve condition, replacing the HCU as necessary. All services will be performed free of charge. The recall began April 1, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S54.
Jan 7, 2019
Ford Motor Company (Ford) is recalling certain 2014 Ford Mustang vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is recalling certain 2011 Ford Ranger and Mercury Milan vehicles, 2011-2012 Ford Fusion and Lincoln Zephyr/MKZ vehicles and 2011-2014 Ford Mustang vehicles sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Ford is also recalling certain 2010 Ford Edge and Lincoln MKX vehicles, 2010-2011 Ford Ranger and Mercury Milan vehicles, 2010-2012 Ford Fusion and Lincoln Zephyr/MKZ vehicles, and 2010-2014 Ford Mustang vehicles sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 13, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall 19S01.
Nov 1, 2018
Ford Motor Company (Ford) is recalling certain 2010 Ford Fusion, Mercury Milan and 2010-2012 Lincoln MKZ vehicles that previously received a replacement passenger air bag under recall 16V-384, 17V-024 or 18V-046. In the event of a crash requiring deployment of the passenger air bag, the bracket that secures the air bag inflator to the module housing may deform, allowing the gas that inflates the air bag to leak out.
Consequence & remedy
Consequence: If the air bag does not inflate as intended, there is an increased risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began November 21, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S34.
Jan 11, 2018
Ford Motor Company (Ford) is recalling certain 2013 Ford Mustang vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is recalling certain 2010 Ford Edge, Fusion, Mustang and Ranger, Lincoln MKX and Zephyr/MKZ, and Mercury Milan vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Ford is also recalling certain 2009 Ford Edge, Fusion, Mustang and Ranger, Lincoln MKX and Zephyr/MKZ, and Mercury Milan vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
May 31, 2016
Ford Motor Company (Ford) is recalling certain model year 2007-2011 Ford Ranger vehicles, 2006-2011 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2007-2010 Ford Edge, Lincoln MKX vehicles, 2005-2006 Ford GT vehicles, and 2005-2011 Ford Mustang vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Ford is recalling certain model year 2007-2008 Ford Ranger, Edge and Lincoln MKX vehicles, 2006-2008 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2005-2006 Ford GT vehicles and 2005-2008 Ford Mustang vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Any vehicle not included in "Zone A", or "Zone B" is not included in the safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Ford mailed interim letters informing owners that parts are not yet available on July 15, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
Nov 24, 2015
Ford Motor Company (Ford) is recalling certain model year 2010-2011 Ford Fusion vehicles manufactured July 21, 2008, to March 4, 2011, and 2010-2011 Mercury Milan vehicles manufactured July 23, 2008, to December 10, 2010. The affected vehicles have fuel vapor canisters whose purge valves may not operate properly resulting in abnormal pressure changes in the fuel tank.
Consequence & remedy
Consequence: The pressure changes may cause the tank to crack and leak fuel. A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy: Ford will notify owners, and dealers will update the vehicle powertrain control modules and inspect the vehicle for any diagnostic trouble codes (DTCs) for this issue and perform a leak test on the Canister Purge Valve (CPV). The fuel tank will be inspected for cracks. The CPV and fuel tank will be replaced as necessary. These repairs will be performed free of charge. The recall began on January 15, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S34.
Dec 7, 2011
FORD IS RECALLING CERTAIN MODEL YEAR 2010-2011 FORD FUSION AND MERCURY MILAN VEHICLES EQUIPPED WITH 17 INCH STEEL WHEELS AND BUILT FROM APRIL 1, 2009, THROUGH APRIL 30, 2009, AND FROM DECEMBER 1, 2009, THROUGH NOVEMBER 13, 2010. THE WHEEL STUDS MAY FRACTURE, POTENTIALLY CAUSING A WHEEL TO SEPARATE.
Consequence & remedy
Consequence: WHILE DRIVING, MULTIPLE STUD FRACTURES COULD OCCUR AT THE WHEEL LOCATION, AND THE OPERATOR MAY EXPERIENCE VEHICLE VIBRATION AND/OR WHEEL SEPARATION, INCREASING THE RISK OF A CRASH.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT THE REAR BRAKE DISC SURFACE FOR FLATNESS AND REPLACE THE DISCS AS NECESSARY. ADDITIONALLY, THE WHEEL LUG NUTS WILL BE REPLACED ON ALL FOUR WHEELS. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR ABOUT JANUARY 24, 2012. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
May 24, 2010
FORD IS RECALLING CERTAIN MODEL YEAR 2010 FUSION, MILAN, AND ESCAPE VEHICLES MANUFACTURED FROM FEBRUARY 27, THROUGH MARCH 26, 2010. THE PARK ROD GUIDE RETENTION PIN MAY NOT HAVE BEEN PROPERLY INSTALLED WHICH FAILS TO CONFORM TO THE REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 114, "THEFT PROTECTION AND ROLLAWAY PREVENTION".
Consequence & remedy
Consequence: A VEHICLE PARKED WITHOUT AN ENGAGED PARK PAWL AND WITHOUT AN APPLIED PARKING BRAKE MAY HAVE UNINTENDED MOVEMENT WHICH MAY CAUSE A CRASH.
Remedy: FORD WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 28, 2010. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332 AND FOR THE HEARING IMPAIRED CALL 1-800-232-5952 (TDD). REPRESENTATIVES ARE AVAILABLE MONDAY THROUGH FRIDAY: 8:00AM - 5:00PM.
Apr 20, 2010
FORD IS RECALLING CERTAIN MODEL YEAR 2010 FUSION, EXPLORER, EXPLORER SPORT TRAC, AND MERCURY MILAN AND MOUNTAINEER VEHICLES MANUFACTURED BETWEEN DECEMBER 15, 2009 THROUGH FEBRUARY 3, 2010 EQUIPPED WITH FRONT SEAT MANUAL RECLINERS. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 202, "HEAD RESTRAINT." THE RECLINER GEAR PLATE TEETH MAY BE OUT OF DIMENSION SPECIFICATION WHICH COULD RESULT IN LIMITED PAWL TO GEAR PLATE TOOTH ENGAGEMENT.
Consequence & remedy
Consequence: IN THE EVENT OF A CRASH, THE SEATBACK AND HEAD RESTRAINT MAY MOVE REARWARD, INCREASING THE RISK OF INJURY.
Remedy: DEALERS WILL REPLACE THE MANUAL RECLINERS FOR BOTH POWER AND MANUAL SEATS FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE APRIL 30, 2010. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
9EA17004 · Power Steering Failure
Opened Nov 20, 2017 · Closed Feb 9, 2024
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:rack And Pinion; Steering:rack And Pinion:rack
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (4)
Steering:electric Power Assist System
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering:rack And Pinion
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering:rack And Pinion:rack
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE16011 · Power Steering Failure
Opened Sep 28, 2016 · Closed Dec 25, 2017
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
Additional source detail variants (2)
Steering:electric Power Assist System
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
Steering
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
PE14030 · Electric Power Steering Failure
Opened Oct 2, 2014 · Closed Sep 10, 2015
Status: closed (inferred from source dates) · Steering:electric Power Assist System
The Office of Defects Investigation (ODI) opened a preliminary evaluation to investigate complaints of the loss of power steering while driving. The subject vehicles are equipped with a rack mounted Electric Power Assisted Steering (EPAS) unit.Some of the complaints alleged that the steering assist failed and resulted in increased steering efforts that contributed to a loss of control and in some cases a crash.The EPAS system was manufactured by TRW Automotive for Ford and was designated as Generation I.These units were first produced and put into vehicle production in July 2008 beginning with the model year (MY) 2010 Ford Fusion and Mercury Milan.The system is comprised of a mechanical steering rack-and-pinion gear with torque sensor, electric assist motor, motor position sensor and a power steering control module (PSCM). The PSCM is self-monitoring and designed to detect faults within the system and can store diagnostic trouble codes (DTCs) if a problem is detected.There are 29 potential DTCs the system can detect.Many of these allow the system to go into reduced-assist steering mode by using the default vehicle speed signal should the live speed signal be lost, if voltage to EPAS system falls below 10.7 or goes above 17 volts, the temperature at the PSCM goes above 105C (221F), or if high friction is detected.Some DTCs will cause the system to go into manual steering mode (no assist). On July 1, 2015, Ford filed a Defect Information Report (DIR) identifying a safety related defect in TRW GEN I EPAS systems installed in some of the subject vehicles (NHTSA Recall 15V-340, Ford No. 15S18).The DIR indicated that intermittent electrical connections caused by quality issues associated with conformal coat contamination and ribbon cable pin misalignment within the steering gear motor may lead to a loss of the motor position sensor signal, resulting in a sudden loss of power assist while driving.The recall covers approximately 393,623 vehicles built from September 2010 through February 2012:2011-12 Fusion built SEP 2010 - FEB 2012; 2011-12 Lincoln MKZ built SEP 2010 - FEB 2012; 2011 Milan built SEP 2010 - DEC 2010; 2011-13 Taurus built SEP 2010 - FEB 2012; 2011-13 Flex with 3.5L GTDI engine built SEP 2010 - FEB 2012; and 2011-13 MKS, MKT with 3.5L GTDI engine built SEP 2010 - FEB 2012.The repair consists of updating the PSCM software to prevent a loss of steering assist while driving. The revised software will provide audible and visual warnings to the driver. If one or more of the following DTCs are stored, C1B00-62, C200B-2F, C200B-61, C200B-62, C200C-2F, C200D-49, U0300-00, U2011-49, U2011-61, U3000-46, U3000-49, U3000-61, U3000-72, U3000-96, P07AE-09, the dealer will replace the EPAS system at no charge to the owner.ODI's analysis of failure data for this PE identified a total of 2,584 complaints to ODI and Ford and 9,967 Ford warranty claims related to the alleged defect.The recalled vehicles account for 1,634 of the complaints and 7,311 of the warranty claims.ODI's analysis identified 40 complaints alleging crashes that may be related to loss of steering assist while driving, 20 of which involved vehicles included in Ford's recall.The information available for the alleged crashes were not sufficient to assess specific causes of the incidents or to verify EPAS malfunctions in each case.Most of the crashes were low-speed impacts with curbs or roadside objects resulting in wheel or minor body damage.None of the injury claims indicated medical attention was required.In addition, statistical modeling of the failure data by NHTSA's National Center for Statistics and Analysis projected 10-year failur
PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
EA12009 · Floor Mat Interference With Accelerator
Opened Dec 12, 2012 · Closed Jun 12, 2014
Status: closed (inferred from source dates) · Vehicle Speed Control; Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Additional source detail variants (2)
Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Vehicle Speed Control
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
EA11009 · Wheel Mounting Stud Fracture
Opened Jul 26, 2011 · Closed Jan 20, 2012
Status: closed (inferred from source dates) · Wheels:lugs/nuts/bolts/studs
To date, the agency is aware of 84 consumer complaints and 361 warranty claims related to the alleged defect in the subject vehicles.In total, 382 subject vehicles reportedly experienced one or more wheel stud fractures, resulting in 7 alleged wheel separation incidents.Most of the reported wheel stud fractures occurred on subject vehicles originally equipped with 17 inch diameter steel wheels (368 of 382) as did all 7 alleged wheel separation incidents.Of the 7 alleged wheel separation incidents, 5 reportedly involved a wheel becoming detached from the subject vehicle's rear axle.The subject vehicles are designed with a safety margin that requires validation of proper wheel joint function with one missing lug nut and all other lug nuts at the minimum torque specification.If multiple stud fractures occur at a wheel location, analysis of reports indicates that the operator may observe vehicle vibration. If the vibration is ignored and the vehicle continues to be driven the remaining studs may fracture, resulting in a wheel separation.By letter dated December 5, 2011, the manufacturer notified the agency that it will conduct a safety recall (identified by NHTSA Recall No.11V-574 and Ford Recall No. 11S23) on certain 2010 and 2011 model year Ford Fusion and Mercury Milan vehicles to address the potential for wheel separation.The recall vehicles were originally equipped with 17 inch diameter steel wheels and were built from April 1, 2009, through April 30, 2009, and from December 1, 2009, through November 13, 2010.Approximately 128,616 vehicles are potentially affected as well as approximately 2,940 service steel wheels distributed to authorized Ford dealers.Ford has identified two distinct root causes of wheel stud fracture in the recall vehicles.First, certain steel wheel centers may have been stamped improperly such that the mounting pad lacks the necessary concavity, which reduces the diameter of the outermost radial points of contact with the brake rotor.This reduces the Belleville washer effect, which reduces the clamp load of the joint.Second, the wheel mounting face on certain rear brake discs may have been machined improperly due to a damaged dust boot on a gauge that measures rear brake rotor parallelism (flatness), resulting in a wheel mounting face that is convex.One or both conditions may induce bending fatigue in the wheel studs.Ford's analysis of manufacturing process information showed that one or both of these two conditions may have been out of control during parts of one or both production ranges covered by the recall.Owners will be notified by mail and instructed to take their vehicles to an authorized Ford or Lincoln dealer to have the lug nuts replaced on all four wheels with new lug nuts treated with a proprietary low-friction coating that improves clamp load given the same applied torque value, and to have the rear brake discs inspected for wheel mounting surface flatness and replaced, if required.Ford will instruct dealers to notify customers who purchased service steel wheels, where information is available, to return vehicles for lug nut replacement.Accordingly, this investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers: 10364337, 10373257, 10378953, 10381431, 10389641, 10389940, 10392373, 10395676, 10396577, 10400071, 10402309, 10416653, 10419175, 10419734, 10420116, 10424191, 10432393, 10434188, 10436471, 10438725 and 10440830.
PE11003 · Wheel Stud Fracture
Opened Jan 21, 2011 · Closed Jul 26, 2011
Status: closed (inferred from source dates) · Wheels:lugs/nuts/bolts/studs
On January 21, 2011, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE11-003) to investigate alleged wheel stud fractures in certain model year (MY) 2010 Ford Fusion vehicles.ODI sent the manufacturer an information request letter dated February 8, 2011 and Ford responded by letter dated March 25, 2011.Ford provided a supplemental response by letter dated July 15, 2011.To date, ODI is aware of 29 complaints related to the alleged defect in the subject vehicles, which now include certain MY2010 Mercury Milan vehicles that are the same or substantially similar to the subject Ford Fusion vehicles in regards to the alleged defect.In total, ODI is aware of 4 reported wheel separation incidents related to the alleged defect in the subject vehicles.The manufacturer's investigation into the root cause of the alleged defect is ongoing.Accordingly, this investigation has been upgraded to an Engineering Analysis (EA11-009) to further study the alleged defect.
AQ10001 · Fleet Vehicle Recall Completion Audit
Opened Nov 18, 2010 · Closed Dec 28, 2015
Status: closed (inferred from source dates) · Unknown Or Other
On November 18, 2010, NHTSA's Recall Management Division (RMD) opened an audit query (AQ10-001) to investigate recall remedy completion by rental car companies on safety recall campaigns.It was expected to provide the agency an indication of how completely and how quickly rental car fleets perform necessary recall-related remedies on the vehicles owned and then rented/leased for use on the roadways.RMD queried three (3) major motor vehicle manufacturers (Ford, Chrysler, and General Motors) and requested data regarding completion figures for fifteen (15) discreet safety recalls.Analysis of this data demonstrated that rental car recalls completion was neither complete nor consistent.The rental car companies representing the largest market share in the industry were then queried as to their respective policies for the rental, lease, and sale of vehicles with open recalls.The data and responses from the manufacturers and the rental car companies can be found in the document repository by accessing the ?Associated Documents link above.In December 2015, Congress enacted the Fixing America's Surface Transportation (FAST) Act.One section of the Act prohibits rental car companies from renting, leasing, or selling motor vehicles subject to open safety recalls.With the passage of the FAST Act and its prohibition, there is no continuing need for the agency to investigate rental car recall completions.Accordingly, this investigation is closed.The agency reserves the right to open any future investigations, including audits of individual recalls, or groups of recalls, or rental car companies, to examine more closely safety recalls performance and completion issues in this area.
PE10019 · Accel Pedal Interference - Acc Floormat
Opened May 28, 2010 · Closed Jan 11, 2013
Status: closed (inferred from source dates) · Vehicle Speed Control:accelerator Pedal
Unsecured mats may interfere with accelerator pedal return to idle. A heel blocker in the floor pan provides a platform that may lift an unsecured mat into contact with the pedal. Ford introduced new pedals as a running change early in model year (MY) 2010 vehicles. Analysis of complaints received by ODI and Ford show elevated rates of pedal entrapment incidents in MY 2008 through early 2010 production vehicles. Incidents typically occur following hard pedal applications to pass slower traffic or when merging into faster traffic. Drivers allege continued high engine power after releasing the accelerator pedal and difficulty braking, including reports that the incident was controlled by shifting to neutral or turning the engine off. Drivers and service technicians reference observing evidence of mat interference or note unsecured Ford or aftermarket all weather floor mats in post-incident inspections.Based on information gathered during the Preliminary Evaluation the population being investigated has been narrowed to model years 2008 to 2010.This investigation has been upgraded to an engineering analysis on MY 2008 through early-2010 vehicles (produced through September 2009) to further assess the scope, frequency and safety consequences of the alleged defect.The VOQs associated with the opening of this Engineering Analysis are: 10479693, 10415911, 10379562, 10372674, 10345830, 10342572, 10339330, 10335336, 10334211, 10332233, 10331160, 10329659, 10327597, 10320011, 10232027, 10214131
Illustration