NHTSA owner reports · September 18, 2026 snapshot.
Engine complaints
700 reportsClear category filterMileage unknown · Jul 22, 2013
EngineFuel/propulsion System
VEHICLE GOES INTO "LIMP-HOME" MODE SUDDENLY AND UNEXPECTEDLY. HAPPENED ON I-95 AND WAS LUCKY I COULD PULL OVER WITHOUT GETTING KILLED. DEALER COULD NOT FIND PROBLEM ALTHOUGH THIS SHOULD HAVE BEEN WELL-KNOWN TO THEM BY THEN. HAPPENED SEVERAL TIMES SINCE AND GOT WORSE AND NOW CAR IS IMMOBILE AND TOO DANGEROUS TO DRIVE. APPARENTLY …
Read full complaint
VEHICLE GOES INTO "LIMP-HOME" MODE SUDDENLY AND UNEXPECTEDLY. HAPPENED ON I-95 AND WAS LUCKY I COULD PULL OVER WITHOUT GETTING KILLED. DEALER COULD NOT FIND PROBLEM ALTHOUGH THIS SHOULD HAVE BEEN WELL-KNOWN TO THEM BY THEN. HAPPENED SEVERAL TIMES SINCE AND GOT WORSE AND NOW CAR IS IMMOBILE AND TOO DANGEROUS TO DRIVE. APPARENTLY A PROBLEM WITH FUEL INJECTION THROTTLE BODY WHICH FORD IS WELL AWARE OF AND PART IS BACK-ORDERED 7-10 DAYS (THEY SAY). NHTSA INITIATED AN INVESTIGATION OF PROBLEM IN FEB 2013 BUT FORD HAS NOT INFORMED CUSTOMERS OF THIS VERY DANGEROUS SITUATION NOR OFFERED ANY FIX. SEEMS UNCONSCIONABLE TO ME. WHAT DOES NHTSA PROPOSE TO DO ABOUT THIS AND WHY HASN'T IT DONE SO? THIS SITUATION IS LITERALLY WITHOUT EXAGGERATION A DANGER TO HUMAN LIFE AND THE MANUFACTURER DOES NOTHING. WHAT IS NHTSA FOR? *TR
NHTSA ODI #10526162
63,000 miles · Jul 22, 2013
EnginePower Train
I WAS AT A LEFT TURN LIGHT AND WHEN I DROVE THROUGH THE LIGHT TO MAKE THE LEFT TURN MY CAR STARTED SHAKING AND THE WRENCH LIGHT CAME OUT. WHEN I WAS HITTING THE GAS IT DIDN'T GO SO I PULLED OVER AND TURNED THE CAR OFF. I WAITED A WHILE AND TURNED IT ON AND IT STARTED UP FINE. SO I STARTED DRIVING A LITTLE MORE AND IT DID IT AGAI…
Read full complaint
I WAS AT A LEFT TURN LIGHT AND WHEN I DROVE THROUGH THE LIGHT TO MAKE THE LEFT TURN MY CAR STARTED SHAKING AND THE WRENCH LIGHT CAME OUT. WHEN I WAS HITTING THE GAS IT DIDN'T GO SO I PULLED OVER AND TURNED THE CAR OFF. I WAITED A WHILE AND TURNED IT ON AND IT STARTED UP FINE. SO I STARTED DRIVING A LITTLE MORE AND IT DID IT AGAIN. I TURNED THE CAR OFF FOR A WHILE AND I TURNED IT BACK ON AND WAS ABLE TO DRIVE IT HOME SINCE I LIVED CLOSE BY. THE WRENCH LIGHT TURNED OFF BUT THE ENGINE LIGHT STAYED ON. I GOT UP THAT MORNING AND DROVE IT TO A NEIGHBORHOOD SHOP AND THEY SAID THE ONLY THING WRONG WITH IT WAS A SECURITY ERROR AND THAT IT WAS FINE. I PICKED IT UP FROM THE SHOP AND I WAS ABLE TO GET DOWN THE STREET WHEN MY CAR CUT OFF. RADIO AND ALL THE INTERIOR LIGHTS WERE ON BUT THE CAR ITSELF CUT OFF AND THE BATTERY LIGHT SHOWED UP. I WAS ABLE TO AGAIN DRIVE IT HOME. I DID SOME RESEARCH AND I DIDN'T REALIZE HOW MANY OTHER PEOPLE WERE HAVING THIS SAME ISSUE AND THEY SAID IT'S THE THROTTLE BODY WHICH WOULD COST ABOUT 600 - 800 DOLLARS TO FIX. THERE SHOULD BE A RECALL ON THIS BECAUSE THIS IS HAPPENING TO WAY TOO MANY PEOPLE AND THIS IS A THREE YEAR OLD CAR. I HAD MY DAUGHTER IN THE CAR BOTH TIMES. *TR
NHTSA ODI #10526124
55,400 miles · Jul 21, 2013
Electrical SystemEngineVehicle Speed Control
60 MPH ON HIGHWAY. WRENCH LIGHT CAME ON. LOST POWER. COASTED TO SIDE OF ROAD (LUCKILY SAFELY). TURNED CAR OFF. RESTARTED AFTER A FEW MINUTES. CONTINUED ABOUT 1/2 MILE. HAPPENED AGAIN. DID SAME THING. CONTINUED ANOTHER 1/2 MILE. DID IT AGAIN. ENGINE SHUTTERED THIS TIME. CHECK ENGINE LIGHT REMAINS ON. WAS ABLE TO …
Read full complaint
60 MPH ON HIGHWAY. WRENCH LIGHT CAME ON. LOST POWER. COASTED TO SIDE OF ROAD (LUCKILY SAFELY). TURNED CAR OFF. RESTARTED AFTER A FEW MINUTES. CONTINUED ABOUT 1/2 MILE. HAPPENED AGAIN. DID SAME THING. CONTINUED ANOTHER 1/2 MILE. DID IT AGAIN. ENGINE SHUTTERED THIS TIME. CHECK ENGINE LIGHT REMAINS ON. WAS ABLE TO RESTART VEHICLE AND GET HOME (APPROXIMATELY 2 MILES). HAPPENED ONCE SHORTLY AFTER USED VEHICLE PURCHASE IN 2011 BUT NEVER DID AGAIN UNTIL NOW. INTERNET SEARCH INDICATES DEFECTIVE THROTTLE BODY PART IS CAUSE. VERY UNSAFE PARTICULARLY IN HIGHWAY DRIVING WHEN THIS HAPPENS! JUST PURCHASED A SECOND 2011 FORD FUSION SE (2011) FOR OUR TEENAGER. CONCERNED ABOUT OUR CHILD'S SAFETY. FORD NEEDS TO ISSUE A RECALL!. *TR
NHTSA ODI #10525966
49,824 miles · Jul 20, 2013
Engine
LEAVING DRIVEWAY VEHICLE APPEARED TO LOOSE ALL POWER FROM THE ENGINE, IT DID NOT STALL, ENGINE INDICATOR LIGHT CAME ON THE FIRST ATTEMPT TO LEAVE BACKED CAR UP INTO DRIVE WAY. CHECKED ALL FLUIDS ENGINE OIL, TRANSMISSION OIL WERE BOTH IN THE APPROPRIATE RANGE. RESTARTING THE CAR ENGINE LIGHT CLEARED, SECOND ATTEMPT TO LEAVE CAR H…
Read full complaint
LEAVING DRIVEWAY VEHICLE APPEARED TO LOOSE ALL POWER FROM THE ENGINE, IT DID NOT STALL, ENGINE INDICATOR LIGHT CAME ON THE FIRST ATTEMPT TO LEAVE BACKED CAR UP INTO DRIVE WAY. CHECKED ALL FLUIDS ENGINE OIL, TRANSMISSION OIL WERE BOTH IN THE APPROPRIATE RANGE. RESTARTING THE CAR ENGINE LIGHT CLEARED, SECOND ATTEMPT TO LEAVE CAR HESITATED AND THEN DID STALL CHECK ENGINE LIGHT RETURNED AND STAYED ILLUMINATED. RESTARTING THE VEHICLE AND RETURNED HOME. LET VEHICLE SET ABOUT TEN MINUTES, RESTARTED ENGINE LIGHT STAYED ON, DROVE CAR SHORT DISTANCE ABOUT .25 MILES DID NOT STALL OR HESITATE HOWEVER CHECK ENGINE LIGHT REMAINED ILLUMINATED. *TR
NHTSA ODI #10525947
47,670 miles · Jul 20, 2013
EnginePower Train
TRAFFIC SLOWED SUDDENLY FROM ABOUT 65MPH TO ABOUT 20-30 MPH SO I HAD TO APPLY MY BRAKES VERY SUDDENLY AND HARD TO AVOID REAR ENDING SOMEONE. TRAFFIC KEPT MOVING AND I REGAINED A SPEED OF ABOUT 40 MPH JUST AFTER THIS I FELT THE CAR MAKE A SUDDEN HARD JERK AND CAR STARTED DECELERATING ON IT'S OWN. I TRIED PUSHING THE GAS PETAL, BU…
Read full complaint
TRAFFIC SLOWED SUDDENLY FROM ABOUT 65MPH TO ABOUT 20-30 MPH SO I HAD TO APPLY MY BRAKES VERY SUDDENLY AND HARD TO AVOID REAR ENDING SOMEONE. TRAFFIC KEPT MOVING AND I REGAINED A SPEED OF ABOUT 40 MPH JUST AFTER THIS I FELT THE CAR MAKE A SUDDEN HARD JERK AND CAR STARTED DECELERATING ON IT'S OWN. I TRIED PUSHING THE GAS PETAL, BUT NOTHING HAPPENED IT WOULD NOT SPEED UP IT KEPT LOOSING SPEED AND EVENTUALLY GOT DOWN TO 1 - 2 MPH. I PULLED THE CAR OVER INTO THE EDGE OF THE RIGHT LANE SO I WAS PARTIALLY ON GRASS AND ON PART OF THE ROAD. I PUT MY HAZARDS ON AND KEPT COASTING BECAUSE IT FELT LIKE THE CAR WAS GOING TO STALL IT WAS SHAKING AND JERKING LIKE IT WANTED TO STALL OUT. I STOPPED THE CAR AND LEFT IT RUNNING I WAS AFRAID IF I SHUT THE CAR COMPLETELY OFF THAT IT WOULD NOT RE-START AGAIN. I THEN DROVE THE CAR HOME WITH MY HAZARDS ON DOING 1 TO 5 MPH ON THE WAY HOME FOR ABOUT 2 MILES. THE WRENCH TOOL LIGHT HAD COME ON WHEN THIS HAPPENED. ONCE I GOT THE CAR HOME I SHUT IT OFF AND RESTARTED AND JUST DROVE BACK AND FORTH IN MY DRIVEWAY. I SHUT THE CAR OFF AND ON ABOUT 3 TIMES AND THEN IT SEEMED TO BE RUNNING NORMAL AND THE TOOL WRENCH LIGHT SHUT OFF. NOT GOING TO DRIVE IT UNTIL I CAN GET IT TO THE FORD DEALER TO HAVE IT LOOKED AT. *TR
NHTSA ODI #10525944
45,000 miles · Jul 20, 2013
EngineVehicle Speed Control
I WAS DRIVING MY CAR AND HAD GONE APPROX 1-1/2 - 2 MILES DOWN THE ROAD AND THE CAR WAS DRIVING FINE THEN ALL OF A SUDDEN MY CAR STARTED TO HESITATE AND WOULD BARELY MOVE. I PULLED OVER ON A SIDE ROAD AND TURNED MY CAR OFF AND RESTARTED IT SOUNDED FINE I TURNED AROUND AND PULLED ONTO MAIN ROAD AGAIN AND AGAIN THE CAR STARTED PUT…
Read full complaint
I WAS DRIVING MY CAR AND HAD GONE APPROX 1-1/2 - 2 MILES DOWN THE ROAD AND THE CAR WAS DRIVING FINE THEN ALL OF A SUDDEN MY CAR STARTED TO HESITATE AND WOULD BARELY MOVE. I PULLED OVER ON A SIDE ROAD AND TURNED MY CAR OFF AND RESTARTED IT SOUNDED FINE I TURNED AROUND AND PULLED ONTO MAIN ROAD AGAIN AND AGAIN THE CAR STARTED PUTTERING AND WOULD BARELY MOVE I MANAGED TO GET CAR OFF THE ROAD. I HAD IT TOWED TO TASCA FORD WHERE THEY SAID THE THROTTLE BODY NEEDED TO BE REPLACED. IT HAS BEEN A WEEK NOW AND I STILL DON'T HAVE MY CAR AND THEY CAN'T TELL ME WHEN THE NEW PART WILL COME IN BECAUSE IT IS BEING MANUFACTURED? THEY ARE ALSO STATING THEY HAVE 18 - 20 CARS WAITING FOR THIS SAME PART. *TR
NHTSA ODI #10525931
62,297 miles · Jul 20, 2013
EngineVehicle Speed Control
FIRST INCIDENT: ON 05/21/2013 CAR HESITATED WHEN PUSHING ACCELERATOR PEDAL AFTER GOING DOWNHILL TO A STOP AND THEN ATTEMPTING TO REACH NORMAL SPEED IN OUR HOUSING DEVELOPMENT (SEE EARLIER REPORT ON 07/18/2013 FOR CONFIRMATION NUMBER: 10525593 AND CAR DEALER RECEIPTS ENCLOSED FOR 05/21/2013). ...UPDATED 08/16/13 *BF SECOND IN…
Read full complaint
FIRST INCIDENT: ON 05/21/2013 CAR HESITATED WHEN PUSHING ACCELERATOR PEDAL AFTER GOING DOWNHILL TO A STOP AND THEN ATTEMPTING TO REACH NORMAL SPEED IN OUR HOUSING DEVELOPMENT (SEE EARLIER REPORT ON 07/18/2013 FOR CONFIRMATION NUMBER: 10525593 AND CAR DEALER RECEIPTS ENCLOSED FOR 05/21/2013). ...UPDATED 08/16/13 *BF SECOND INCIDENT: ON 06/21/2013 CAR DID NOT RESPOND BEYOND IDLE SPEED AFTER PUSHING ACCELERATOR PEDAL TO MOVE FROM STOP LIGHT AND DRIFTED TO NEARBY PARKING LOT WITH NO ACCELERATOR PEDAL RESPONSE BEYOND IDLE POWER (SEE EARLIER REPORT ON 07/18/2013 FOR CONFIRMATION NUMBER: 10525593 AND CAR DEALER RECEIPTS ENCLOSED FOR 06/21/2013) ...UPDATED 08/16/13 *BF *TR
NHTSA ODI #10525877
63,745 miles · Jul 19, 2013
EngineFuel System, GasolineVehicle Speed Control
WHILE ACCELERATING, CRUISING OR AT IDLE, THE ENGINE STALLS THEN DIES. WHEN RESTARTING ENGINE STUMBLES BADLY AND DIES. THIS HAPPENS IN TRAFFIC, ACCELERATING INTO INTERSECTIONS, AT HIGHWAY SPEEDS, ETC. MIL IS NOW ON CONSTANTLY. VEHICLE IS COMPLETELY UNUSABLE BECAUSE IT IS PAST THE WARRANTY PERIOD. WE WILL BE REPLACING THE THROTTLE…
Read full complaint
WHILE ACCELERATING, CRUISING OR AT IDLE, THE ENGINE STALLS THEN DIES. WHEN RESTARTING ENGINE STUMBLES BADLY AND DIES. THIS HAPPENS IN TRAFFIC, ACCELERATING INTO INTERSECTIONS, AT HIGHWAY SPEEDS, ETC. MIL IS NOW ON CONSTANTLY. VEHICLE IS COMPLETELY UNUSABLE BECAUSE IT IS PAST THE WARRANTY PERIOD. WE WILL BE REPLACING THE THROTTLE BODY AT OUR OWN EXPENSE, BUT WOULD LIKE FORD TO REIMBURSE US. *TR
NHTSA ODI #10525819
38,300 miles · Jul 19, 2013
EngineFuel System, GasolinePower Train
I WAS DRIVING ON MY WAY TO WORK WHEN MY CAR LOST POWER I PULLED OVER TURNED THE CAR OFF. UPON RESTARTING IT THE CHECK ENGINE LIGHT WAS ON, I PRECEDED TO WORK. WHEN I GOT OFF OF WORK AND WENT HOME THE CHECK ENGINE LIGHT WAS OFF. A WEEK LATER THE SYMPTOMS HAPPENED AGAIN THIS TIME IT WAS MORE THEN ONCE. CLOSE TO A TOTAL OF 10 TIMES…
Read full complaint
I WAS DRIVING ON MY WAY TO WORK WHEN MY CAR LOST POWER I PULLED OVER TURNED THE CAR OFF. UPON RESTARTING IT THE CHECK ENGINE LIGHT WAS ON, I PRECEDED TO WORK. WHEN I GOT OFF OF WORK AND WENT HOME THE CHECK ENGINE LIGHT WAS OFF. A WEEK LATER THE SYMPTOMS HAPPENED AGAIN THIS TIME IT WAS MORE THEN ONCE. CLOSE TO A TOTAL OF 10 TIMES IN A ONE HOUR PERIOD. *TR
NHTSA ODI #10525816
46,900 miles · Jul 19, 2013
EngineVehicle Speed Control
I WAS DRIVING DOWN A HIGHWAY WHEN THE ENGINE SUDDENLY LOST POWER WITHOUT WARNING. I QUICKLY WENT FROM 70 MPH TO 50 MPH AND CONTINUED TO SLOW. THE VEHICLE ENGINE LIGHT CAME ON THE INSTRUMENT PANEL AND MY RPMS DROPPED BELOW 500. I WAS ABLE TO SAFELY PULL OVER TO THE SHOULDER. I TURNED THE CAR OFF, WAITED A FEW MINUTES, AND STA…
Read full complaint
I WAS DRIVING DOWN A HIGHWAY WHEN THE ENGINE SUDDENLY LOST POWER WITHOUT WARNING. I QUICKLY WENT FROM 70 MPH TO 50 MPH AND CONTINUED TO SLOW. THE VEHICLE ENGINE LIGHT CAME ON THE INSTRUMENT PANEL AND MY RPMS DROPPED BELOW 500. I WAS ABLE TO SAFELY PULL OVER TO THE SHOULDER. I TURNED THE CAR OFF, WAITED A FEW MINUTES, AND STARTED IT. THE CAR STARTED AND IDLED JUST FINE. I REVVED THE ENGINE A FEW TIMES. RPMS STAYED IN THE NORMAL RANGE. I PUT THE CAR IN GEAR AND STARTED TO MOVE. IMMEDIATELY THE ENGINE LIGHT CAME BACK ON AND THE RPMS DROPPED AGAIN. I HAD THE CAR TOWED TO A REPAIR SHOP WHERE THEY INFORMED ME THE THROTTLE BODY HAD FAILED AND IT REQUIRED REPLACEMENT. THE TOW AND REPAIRS COST ME OVER $500. *TR
NHTSA ODI #10525749
Official recalls
11Mar 10, 2021
Ford Motor Company (Ford) is recalling certain 2007-2011 Ranger, 2006-2012 Fusion, Lincoln Zephyr, Lincoln MKZ, 2006-2011 Mercury Milan, 2007-2010 Ford Edge, and Lincoln MKX vehicles. The driver's side air bag inflator may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will replace the driver-side airbag inflator or module with an alternate one, free of charge. Owner notification letters were mailed on April 9, 2021 for the passenger side, and November 14, 2022 for the driver side. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S12.
Feb 16, 2021
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Additional source detail variants (3)
Air Bags:frontal:passenger Side:inflator Module
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Air Bags:frontal:driver Side:inflator Module
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Air Bags:frontal
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Dec 18, 2019
Ford Motor Company (Ford) is recalling certain 2006-2010 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ vehicles. The valves within the ABS Hydraulic Control Units (HCU) may react with brake fluids containing specific corrosion preventative additives. This reaction may cause the valves to not close properly.
Consequence & remedy
Consequence: If the valves do not properly close, additional brake pedal travel may be required to stop the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will flush the brake system with DOT 4 fluid and install a new brake fluid reservoir cap. In addition, the HCU will be tested to detect a possible stuck valve condition, replacing the HCU as necessary. All services will be performed free of charge. The recall began April 1, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S54.
Jan 7, 2019
Ford Motor Company (Ford) is recalling certain 2014 Ford Mustang vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is recalling certain 2011 Ford Ranger and Mercury Milan vehicles, 2011-2012 Ford Fusion and Lincoln Zephyr/MKZ vehicles and 2011-2014 Ford Mustang vehicles sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Ford is also recalling certain 2010 Ford Edge and Lincoln MKX vehicles, 2010-2011 Ford Ranger and Mercury Milan vehicles, 2010-2012 Ford Fusion and Lincoln Zephyr/MKZ vehicles, and 2010-2014 Ford Mustang vehicles sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 13, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall 19S01.
Nov 1, 2018
Ford Motor Company (Ford) is recalling certain 2010 Ford Fusion, Mercury Milan and 2010-2012 Lincoln MKZ vehicles that previously received a replacement passenger air bag under recall 16V-384, 17V-024 or 18V-046. In the event of a crash requiring deployment of the passenger air bag, the bracket that secures the air bag inflator to the module housing may deform, allowing the gas that inflates the air bag to leak out.
Consequence & remedy
Consequence: If the air bag does not inflate as intended, there is an increased risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began November 21, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S34.
Jan 11, 2018
Ford Motor Company (Ford) is recalling certain 2013 Ford Mustang vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is recalling certain 2010 Ford Edge, Fusion, Mustang and Ranger, Lincoln MKX and Zephyr/MKZ, and Mercury Milan vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Ford is also recalling certain 2009 Ford Edge, Fusion, Mustang and Ranger, Lincoln MKX and Zephyr/MKZ, and Mercury Milan vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
May 31, 2016
Ford Motor Company (Ford) is recalling certain model year 2007-2011 Ford Ranger vehicles, 2006-2011 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2007-2010 Ford Edge, Lincoln MKX vehicles, 2005-2006 Ford GT vehicles, and 2005-2011 Ford Mustang vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Ford is recalling certain model year 2007-2008 Ford Ranger, Edge and Lincoln MKX vehicles, 2006-2008 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2005-2006 Ford GT vehicles and 2005-2008 Ford Mustang vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Any vehicle not included in "Zone A", or "Zone B" is not included in the safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Ford mailed interim letters informing owners that parts are not yet available on July 15, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
Nov 24, 2015
Ford Motor Company (Ford) is recalling certain model year 2010-2011 Ford Fusion vehicles manufactured July 21, 2008, to March 4, 2011, and 2010-2011 Mercury Milan vehicles manufactured July 23, 2008, to December 10, 2010. The affected vehicles have fuel vapor canisters whose purge valves may not operate properly resulting in abnormal pressure changes in the fuel tank.
Consequence & remedy
Consequence: The pressure changes may cause the tank to crack and leak fuel. A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy: Ford will notify owners, and dealers will update the vehicle powertrain control modules and inspect the vehicle for any diagnostic trouble codes (DTCs) for this issue and perform a leak test on the Canister Purge Valve (CPV). The fuel tank will be inspected for cracks. The CPV and fuel tank will be replaced as necessary. These repairs will be performed free of charge. The recall began on January 15, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S34.
Dec 7, 2011
FORD IS RECALLING CERTAIN MODEL YEAR 2010-2011 FORD FUSION AND MERCURY MILAN VEHICLES EQUIPPED WITH 17 INCH STEEL WHEELS AND BUILT FROM APRIL 1, 2009, THROUGH APRIL 30, 2009, AND FROM DECEMBER 1, 2009, THROUGH NOVEMBER 13, 2010. THE WHEEL STUDS MAY FRACTURE, POTENTIALLY CAUSING A WHEEL TO SEPARATE.
Consequence & remedy
Consequence: WHILE DRIVING, MULTIPLE STUD FRACTURES COULD OCCUR AT THE WHEEL LOCATION, AND THE OPERATOR MAY EXPERIENCE VEHICLE VIBRATION AND/OR WHEEL SEPARATION, INCREASING THE RISK OF A CRASH.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT THE REAR BRAKE DISC SURFACE FOR FLATNESS AND REPLACE THE DISCS AS NECESSARY. ADDITIONALLY, THE WHEEL LUG NUTS WILL BE REPLACED ON ALL FOUR WHEELS. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR ABOUT JANUARY 24, 2012. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
May 24, 2010
FORD IS RECALLING CERTAIN MODEL YEAR 2010 FUSION, MILAN, AND ESCAPE VEHICLES MANUFACTURED FROM FEBRUARY 27, THROUGH MARCH 26, 2010. THE PARK ROD GUIDE RETENTION PIN MAY NOT HAVE BEEN PROPERLY INSTALLED WHICH FAILS TO CONFORM TO THE REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 114, "THEFT PROTECTION AND ROLLAWAY PREVENTION".
Consequence & remedy
Consequence: A VEHICLE PARKED WITHOUT AN ENGAGED PARK PAWL AND WITHOUT AN APPLIED PARKING BRAKE MAY HAVE UNINTENDED MOVEMENT WHICH MAY CAUSE A CRASH.
Remedy: FORD WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 28, 2010. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332 AND FOR THE HEARING IMPAIRED CALL 1-800-232-5952 (TDD). REPRESENTATIVES ARE AVAILABLE MONDAY THROUGH FRIDAY: 8:00AM - 5:00PM.
Apr 20, 2010
FORD IS RECALLING CERTAIN MODEL YEAR 2010 FUSION, EXPLORER, EXPLORER SPORT TRAC, AND MERCURY MILAN AND MOUNTAINEER VEHICLES MANUFACTURED BETWEEN DECEMBER 15, 2009 THROUGH FEBRUARY 3, 2010 EQUIPPED WITH FRONT SEAT MANUAL RECLINERS. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 202, "HEAD RESTRAINT." THE RECLINER GEAR PLATE TEETH MAY BE OUT OF DIMENSION SPECIFICATION WHICH COULD RESULT IN LIMITED PAWL TO GEAR PLATE TOOTH ENGAGEMENT.
Consequence & remedy
Consequence: IN THE EVENT OF A CRASH, THE SEATBACK AND HEAD RESTRAINT MAY MOVE REARWARD, INCREASING THE RISK OF INJURY.
Remedy: DEALERS WILL REPLACE THE MANUAL RECLINERS FOR BOTH POWER AND MANUAL SEATS FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE APRIL 30, 2010. OWNERS MAY CONTACT FORD AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
9EA17004 · Power Steering Failure
Opened Nov 20, 2017 · Closed Feb 9, 2024
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:rack And Pinion; Steering:rack And Pinion:rack
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (4)
Steering:electric Power Assist System
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering:rack And Pinion
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering:rack And Pinion:rack
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE16011 · Power Steering Failure
Opened Sep 28, 2016 · Closed Dec 25, 2017
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
Additional source detail variants (2)
Steering:electric Power Assist System
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
Steering
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
PE14030 · Electric Power Steering Failure
Opened Oct 2, 2014 · Closed Sep 10, 2015
Status: closed (inferred from source dates) · Steering:electric Power Assist System
The Office of Defects Investigation (ODI) opened a preliminary evaluation to investigate complaints of the loss of power steering while driving. The subject vehicles are equipped with a rack mounted Electric Power Assisted Steering (EPAS) unit.Some of the complaints alleged that the steering assist failed and resulted in increased steering efforts that contributed to a loss of control and in some cases a crash.The EPAS system was manufactured by TRW Automotive for Ford and was designated as Generation I.These units were first produced and put into vehicle production in July 2008 beginning with the model year (MY) 2010 Ford Fusion and Mercury Milan.The system is comprised of a mechanical steering rack-and-pinion gear with torque sensor, electric assist motor, motor position sensor and a power steering control module (PSCM). The PSCM is self-monitoring and designed to detect faults within the system and can store diagnostic trouble codes (DTCs) if a problem is detected.There are 29 potential DTCs the system can detect.Many of these allow the system to go into reduced-assist steering mode by using the default vehicle speed signal should the live speed signal be lost, if voltage to EPAS system falls below 10.7 or goes above 17 volts, the temperature at the PSCM goes above 105C (221F), or if high friction is detected.Some DTCs will cause the system to go into manual steering mode (no assist). On July 1, 2015, Ford filed a Defect Information Report (DIR) identifying a safety related defect in TRW GEN I EPAS systems installed in some of the subject vehicles (NHTSA Recall 15V-340, Ford No. 15S18).The DIR indicated that intermittent electrical connections caused by quality issues associated with conformal coat contamination and ribbon cable pin misalignment within the steering gear motor may lead to a loss of the motor position sensor signal, resulting in a sudden loss of power assist while driving.The recall covers approximately 393,623 vehicles built from September 2010 through February 2012:2011-12 Fusion built SEP 2010 - FEB 2012; 2011-12 Lincoln MKZ built SEP 2010 - FEB 2012; 2011 Milan built SEP 2010 - DEC 2010; 2011-13 Taurus built SEP 2010 - FEB 2012; 2011-13 Flex with 3.5L GTDI engine built SEP 2010 - FEB 2012; and 2011-13 MKS, MKT with 3.5L GTDI engine built SEP 2010 - FEB 2012.The repair consists of updating the PSCM software to prevent a loss of steering assist while driving. The revised software will provide audible and visual warnings to the driver. If one or more of the following DTCs are stored, C1B00-62, C200B-2F, C200B-61, C200B-62, C200C-2F, C200D-49, U0300-00, U2011-49, U2011-61, U3000-46, U3000-49, U3000-61, U3000-72, U3000-96, P07AE-09, the dealer will replace the EPAS system at no charge to the owner.ODI's analysis of failure data for this PE identified a total of 2,584 complaints to ODI and Ford and 9,967 Ford warranty claims related to the alleged defect.The recalled vehicles account for 1,634 of the complaints and 7,311 of the warranty claims.ODI's analysis identified 40 complaints alleging crashes that may be related to loss of steering assist while driving, 20 of which involved vehicles included in Ford's recall.The information available for the alleged crashes were not sufficient to assess specific causes of the incidents or to verify EPAS malfunctions in each case.Most of the crashes were low-speed impacts with curbs or roadside objects resulting in wheel or minor body damage.None of the injury claims indicated medical attention was required.In addition, statistical modeling of the failure data by NHTSA's National Center for Statistics and Analysis projected 10-year failur
PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
EA12009 · Floor Mat Interference With Accelerator
Opened Dec 12, 2012 · Closed Jun 12, 2014
Status: closed (inferred from source dates) · Vehicle Speed Control; Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Additional source detail variants (2)
Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Vehicle Speed Control
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
EA11009 · Wheel Mounting Stud Fracture
Opened Jul 26, 2011 · Closed Jan 20, 2012
Status: closed (inferred from source dates) · Wheels:lugs/nuts/bolts/studs
To date, the agency is aware of 84 consumer complaints and 361 warranty claims related to the alleged defect in the subject vehicles.In total, 382 subject vehicles reportedly experienced one or more wheel stud fractures, resulting in 7 alleged wheel separation incidents.Most of the reported wheel stud fractures occurred on subject vehicles originally equipped with 17 inch diameter steel wheels (368 of 382) as did all 7 alleged wheel separation incidents.Of the 7 alleged wheel separation incidents, 5 reportedly involved a wheel becoming detached from the subject vehicle's rear axle.The subject vehicles are designed with a safety margin that requires validation of proper wheel joint function with one missing lug nut and all other lug nuts at the minimum torque specification.If multiple stud fractures occur at a wheel location, analysis of reports indicates that the operator may observe vehicle vibration. If the vibration is ignored and the vehicle continues to be driven the remaining studs may fracture, resulting in a wheel separation.By letter dated December 5, 2011, the manufacturer notified the agency that it will conduct a safety recall (identified by NHTSA Recall No.11V-574 and Ford Recall No. 11S23) on certain 2010 and 2011 model year Ford Fusion and Mercury Milan vehicles to address the potential for wheel separation.The recall vehicles were originally equipped with 17 inch diameter steel wheels and were built from April 1, 2009, through April 30, 2009, and from December 1, 2009, through November 13, 2010.Approximately 128,616 vehicles are potentially affected as well as approximately 2,940 service steel wheels distributed to authorized Ford dealers.Ford has identified two distinct root causes of wheel stud fracture in the recall vehicles.First, certain steel wheel centers may have been stamped improperly such that the mounting pad lacks the necessary concavity, which reduces the diameter of the outermost radial points of contact with the brake rotor.This reduces the Belleville washer effect, which reduces the clamp load of the joint.Second, the wheel mounting face on certain rear brake discs may have been machined improperly due to a damaged dust boot on a gauge that measures rear brake rotor parallelism (flatness), resulting in a wheel mounting face that is convex.One or both conditions may induce bending fatigue in the wheel studs.Ford's analysis of manufacturing process information showed that one or both of these two conditions may have been out of control during parts of one or both production ranges covered by the recall.Owners will be notified by mail and instructed to take their vehicles to an authorized Ford or Lincoln dealer to have the lug nuts replaced on all four wheels with new lug nuts treated with a proprietary low-friction coating that improves clamp load given the same applied torque value, and to have the rear brake discs inspected for wheel mounting surface flatness and replaced, if required.Ford will instruct dealers to notify customers who purchased service steel wheels, where information is available, to return vehicles for lug nut replacement.Accordingly, this investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers: 10364337, 10373257, 10378953, 10381431, 10389641, 10389940, 10392373, 10395676, 10396577, 10400071, 10402309, 10416653, 10419175, 10419734, 10420116, 10424191, 10432393, 10434188, 10436471, 10438725 and 10440830.
PE11003 · Wheel Stud Fracture
Opened Jan 21, 2011 · Closed Jul 26, 2011
Status: closed (inferred from source dates) · Wheels:lugs/nuts/bolts/studs
On January 21, 2011, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE11-003) to investigate alleged wheel stud fractures in certain model year (MY) 2010 Ford Fusion vehicles.ODI sent the manufacturer an information request letter dated February 8, 2011 and Ford responded by letter dated March 25, 2011.Ford provided a supplemental response by letter dated July 15, 2011.To date, ODI is aware of 29 complaints related to the alleged defect in the subject vehicles, which now include certain MY2010 Mercury Milan vehicles that are the same or substantially similar to the subject Ford Fusion vehicles in regards to the alleged defect.In total, ODI is aware of 4 reported wheel separation incidents related to the alleged defect in the subject vehicles.The manufacturer's investigation into the root cause of the alleged defect is ongoing.Accordingly, this investigation has been upgraded to an Engineering Analysis (EA11-009) to further study the alleged defect.
AQ10001 · Fleet Vehicle Recall Completion Audit
Opened Nov 18, 2010 · Closed Dec 28, 2015
Status: closed (inferred from source dates) · Unknown Or Other
On November 18, 2010, NHTSA's Recall Management Division (RMD) opened an audit query (AQ10-001) to investigate recall remedy completion by rental car companies on safety recall campaigns.It was expected to provide the agency an indication of how completely and how quickly rental car fleets perform necessary recall-related remedies on the vehicles owned and then rented/leased for use on the roadways.RMD queried three (3) major motor vehicle manufacturers (Ford, Chrysler, and General Motors) and requested data regarding completion figures for fifteen (15) discreet safety recalls.Analysis of this data demonstrated that rental car recalls completion was neither complete nor consistent.The rental car companies representing the largest market share in the industry were then queried as to their respective policies for the rental, lease, and sale of vehicles with open recalls.The data and responses from the manufacturers and the rental car companies can be found in the document repository by accessing the ?Associated Documents link above.In December 2015, Congress enacted the Fixing America's Surface Transportation (FAST) Act.One section of the Act prohibits rental car companies from renting, leasing, or selling motor vehicles subject to open safety recalls.With the passage of the FAST Act and its prohibition, there is no continuing need for the agency to investigate rental car recall completions.Accordingly, this investigation is closed.The agency reserves the right to open any future investigations, including audits of individual recalls, or groups of recalls, or rental car companies, to examine more closely safety recalls performance and completion issues in this area.
PE10019 · Accel Pedal Interference - Acc Floormat
Opened May 28, 2010 · Closed Jan 11, 2013
Status: closed (inferred from source dates) · Vehicle Speed Control:accelerator Pedal
Unsecured mats may interfere with accelerator pedal return to idle. A heel blocker in the floor pan provides a platform that may lift an unsecured mat into contact with the pedal. Ford introduced new pedals as a running change early in model year (MY) 2010 vehicles. Analysis of complaints received by ODI and Ford show elevated rates of pedal entrapment incidents in MY 2008 through early 2010 production vehicles. Incidents typically occur following hard pedal applications to pass slower traffic or when merging into faster traffic. Drivers allege continued high engine power after releasing the accelerator pedal and difficulty braking, including reports that the incident was controlled by shifting to neutral or turning the engine off. Drivers and service technicians reference observing evidence of mat interference or note unsecured Ford or aftermarket all weather floor mats in post-incident inspections.Based on information gathered during the Preliminary Evaluation the population being investigated has been narrowed to model years 2008 to 2010.This investigation has been upgraded to an engineering analysis on MY 2008 through early-2010 vehicles (produced through September 2009) to further assess the scope, frequency and safety consequences of the alleged defect.The VOQs associated with the opening of this Engineering Analysis are: 10479693, 10415911, 10379562, 10372674, 10345830, 10342572, 10339330, 10335336, 10334211, 10332233, 10331160, 10329659, 10327597, 10320011, 10232027, 10214131
Illustration