NHTSA owner reports · September 18, 2026 snapshot.
Service Brakes complaints
473 reportsClear category filterMileage unknown · Dec 27, 2016
Service Brakes
THIS HAS OCCURRED SEVERAL TIMES OVER THE PAST YEAR WITH MY 2009 FORD FUSION THAT CURRENTLY HAS 74,000 MILES ON IT. WHEN PRESSING THE BRAKE PEDAL WHILE DRIVING OVER A SMALL POTHOLE OR SLIGHTLY DAMP ROAD SURFACE, THE ABS SYSTEM ENGAGES. THE BRAKE PEDAL FEELS AS THOUGH IT IS GRINDING AND PUSHING BACK ON MY FOOT, AND THE CAR DOES NO…
Read full complaint
THIS HAS OCCURRED SEVERAL TIMES OVER THE PAST YEAR WITH MY 2009 FORD FUSION THAT CURRENTLY HAS 74,000 MILES ON IT. WHEN PRESSING THE BRAKE PEDAL WHILE DRIVING OVER A SMALL POTHOLE OR SLIGHTLY DAMP ROAD SURFACE, THE ABS SYSTEM ENGAGES. THE BRAKE PEDAL FEELS AS THOUGH IT IS GRINDING AND PUSHING BACK ON MY FOOT, AND THE CAR DOES NOT STOP. I PRESS THE BRAKE AS HARD AS I CAN TO TRY TO STOP THE CAR. THE BRAKE PEDAL CONTINUES TO FEEL AS THOUGH IT IS GRINDING AND THEN DROPS TO THE FLOOR. THE CAR EVENTUALLY COMES TO A STOP. I HAVE NEARLY BEEN IN SEVERAL ACCIDENTS, DUE TO THE CAR'S INABILITY TO STOP IMMEDIATELY. CURRENTLY, I HAVE TO DRIVE SEVERAL FEET BEHIND THE CAR IN FRONT OF ME, EVEN ON FLAT, DRY ROAD SURFACES. NOW WHEN I PRESS THE BRAKE PEDAL, THE BRAKES ENGAGE, BUT THEN DISENGAGE, UNTIL THE BRAKE PEDAL IS PRESSED TO THE FLOOR. ONCE THE BRAKE PEDAL IS ON THE FLOOR, THE CAR SLOWLY COMES TO A STOP. THE CAR WILL NOT STOP IMMEDIATELY. IT IS DANGEROUS TO DRIVE THE CAR, BECAUSE OF THIS. I MUST KNOW WELL AHEAD OF TIME WHEN I HAVE TO STOP THE CAR. *TR
NHTSA ODI #10937599
63,000 miles · Dec 12, 2016
Service Brakes
I PURCHASED THIS USED CAR ON SEPT. 28, 2016. FIVE WEEKS LATER, ON NOV. 4, I WAS NEARING A RED LIGHT ON A CITY STREET AND BEGAN TO BRAKE. UNEXPECTEDLY, THE ABS ENGAGED AND I FOUND MYSELF WITHOUT ANY BRAKING POWER. I HAD TO PUSH THE BRAKE PEDAL TO THE FLOOR UNTIL THE CAR EVENTUALLY STOPPED APPROXIMATELY 12-15 FEET LATER. IF ANOTHE…
Read full complaint
I PURCHASED THIS USED CAR ON SEPT. 28, 2016. FIVE WEEKS LATER, ON NOV. 4, I WAS NEARING A RED LIGHT ON A CITY STREET AND BEGAN TO BRAKE. UNEXPECTEDLY, THE ABS ENGAGED AND I FOUND MYSELF WITHOUT ANY BRAKING POWER. I HAD TO PUSH THE BRAKE PEDAL TO THE FLOOR UNTIL THE CAR EVENTUALLY STOPPED APPROXIMATELY 12-15 FEET LATER. IF ANOTHER CAR OR A PERSON HAD BEEN IN FRONT OF ME, I WOULD HAVE HIT THEM. I IMMEDIATELY CONTACTED THE FORD DEALERSHIP WHERE I BOUGHT THE CAR (AUTONATION FORD OF WHITE BEAT LAKE, MINNESOTA), TOLD THEM WHAT HAPPENED AND THEN DROVE MY CAR SLOWLY TO THE DEALERSHIP WHERE THEY KEPT IT FOR FOUR DAYS. THEY REPLACED THE MASTER CYLINDER AND I WAS LED TO BELIEVE THAT THAT WAS THE END OF THE PROBLEM. THE DEALERSHIP CLAIMED THAT THEY DIDN'T KNOW WHAT ELSE MIGHT HAVE CAUSED SUCH A BRAKING PROBLEM. FIVE WEEKS LATER, ON DEC. 10, 2016, THE SAME THING HAPPENED ON ANOTHER CITY STREET AS I APPROACHED A RED LIGHT EXCEPT THIS TIME THE ABS ENGAGED BECAUSE THE ROAD WAS SEMI-SLIPPERY AFTER A SNOWFALL AND I HAD TO BRAKE A BIT HARDER. AGAIN, THE BRAKES DIDN'T WORK PROPERLY AND I HAD TO PRESS THEM TO THE FLOOR. MY CAR ENDED UP SLIDING THROUGH THE INTERSECTION (AGAINST A RED LIGHT) BEFORE COMING TO A STOP. LUCKILY, THERE WASN'T ANY OTHER TRAFFIC OR OBSTACLES IN THE INTERSECTION OR I WOULD HAVE HIT THEM AS WELL. I DID SOME RESEARCH ON THE INTERNET AND DISCOVERED THAT THERE HAVE BEEN NUMEROUS SIMILAR COMPLAINTS WITH FORD FUSION ABS SYSTEMS, INCLUDING A NUMBER OF COMPLAINTS MADE TO NHTSA. (THERE'S ALSO A VIDEO ABOUT THE PROBLEM AT YOUTUBE.) I DISCOVERED THAT THE PROBLEM IS OFTEN MISDIAGNOSED AND THAT THE CAUSE IF A FAULTY/DEFECTIVE ABS HYDRAULIC CONTROL UNIT NEEDING TO BE REPLACED IN A SIGNIFICANT NUMBER OF FUSIONS BUILT WITHIN THE LAST SEVERAL YEARS. THESE FORD FUSIONS WITH FAULTY ABS NEED TO BE RECALLED BEFORE THERE ARE INJURIES AND FATALITIES, IF THERE HAVEN'T BEEN ALREADY.
NHTSA ODI #10934917
82,000 miles · Dec 2, 2016
Service Brakes
THIS IS THE SECOND TIME WE'VE HAD ISSUES WITH THE BRAKING SYSTEM ON OUR 2009 FORD FUSION. THE FIRST OCCURRENCE WAS IN AUGUST 2016, THE SECOND ON NOVEMBER 30, 2016. THIS LAST TIME I TOOK THE VEHICLE TO THE LOCAL FORD DEALER AND HAD THEM DO A THOROUGH DIAGNOSTIC CHECK ON THE BRAKING SYSTEM. THE DEALERSHIP SAYS THERE IS NOTHING WRO…
Read full complaint
THIS IS THE SECOND TIME WE'VE HAD ISSUES WITH THE BRAKING SYSTEM ON OUR 2009 FORD FUSION. THE FIRST OCCURRENCE WAS IN AUGUST 2016, THE SECOND ON NOVEMBER 30, 2016. THIS LAST TIME I TOOK THE VEHICLE TO THE LOCAL FORD DEALER AND HAD THEM DO A THOROUGH DIAGNOSTIC CHECK ON THE BRAKING SYSTEM. THE DEALERSHIP SAYS THERE IS NOTHING WRONG WITH OUR BRAKES THAT THEY CAN DOCUMENT OR REPLICATE. HOWEVER, THE FAILURE OF THE BREAKING SYSTEM, TEMPORARILY, NEARLY CAUSED AN ACCIDENT FOR MY SON THIS WEEK. BACK IN AUGUST IT WAS MY WIFE THAT HAD THE EPISODE. IN AUGUST SHE WAS DRIVING ON A WET BLACKTOP FOUR-LANE DIVIDED HIGHWAY AND HIT THE BREAKS FOR A CAR SLOWING IN FRONT OF HER. IMMEDIATELY SHE HAD ALMOST NO BREAKING FUNCTION, WITH THE PEDAL BEING EXTREMELY SOFT AND GOING ALMOST TO THE FLOOR. THIS WAS NOT A CASE OF PULSATING ABS ACTION LIKE NORMAL. SHE WAS ABLE TO PUMP THE BRAKES AGGRESSIVELY FOR A WHILE AND GRADUALLY GET BACK ENOUGH BREAKING FUNCTION TO DRIVE THE CAR HOME. ON INSPECTION THE BRAKE RESERVOIR WAS FULL. THIS WEEK, THE SAME THING HAPPENED ON A PERFECTLY DRY CONCRETE FOUR-LANE DIVIDED HIGHWAY DURING A BRAKING ACTION WHEN PREPARING TO MAKE A TURN ONTO A SIDE ROAD. HE NEARLY HIT A BRICK SIGN AT THE COLLEGE CAMPUS ENTRANCE. HE PUMPED THE BRAKES REPEATEDLY AND GRADUALLY HAD ENOUGH BREAKING FUNCTION RETURN THAT HE COULD DRIVE SLOWLY TO THE PARKING LOT. I TOOK OFF WORK AND DROVE DOWN TO MEET HIM AND TESTED THE VEHICLE. THE MASTER CYLINDER WAS FULL TO THE NORMAL LEVEL. THERE WAS NO SIGN OF LEAKING ON ANY OF THE CALIPERS OR ON THE GROUND BELOW. THE BRAKE PEDAL WAS STILL VERY SOFT BUT AFTER PUMPING GRADUALLY RETURNED TO NORMAL SO THAT I COULD DRIVE THE VEHICLE HOME VERY SLOWLY. WE'VE NOW ALMOST HAD TWO ACCIDENTS WHEN THE BRAKES FAIL TEMPORARILY AND WITHOUT WARNING, THEN GRADUALLY RETURN TO NORMAL OPERATION. WHAT IS GOING ON HERE? THIS IS REALLY SCARY AND FRUSTRATING. *TR
NHTSA ODI #10929668
115,000 miles · Dec 1, 2016
Service Brakes
AFTER APPLYING BRAKES AND ENGAGING THE ABS WHILE THE ROAD WAS WET OR HAD SNOW ON IT, THE PEDAL GOES ALMOST COMPLETELY TO THE FLOOR AND STAYS SOFT UNTIL I CONTINUOUSLY PUMP THE BRAKES TO GET IT BACK TO NORMAL. THE CAR HAS DONE THIS APPROXIMATELY 6 TIMES OVER THE PAST 3 YEARS I'VE OWNED THE CAR. IT HAS 115K MILES ON IT. A LOT OF P…
Read full complaint
AFTER APPLYING BRAKES AND ENGAGING THE ABS WHILE THE ROAD WAS WET OR HAD SNOW ON IT, THE PEDAL GOES ALMOST COMPLETELY TO THE FLOOR AND STAYS SOFT UNTIL I CONTINUOUSLY PUMP THE BRAKES TO GET IT BACK TO NORMAL. THE CAR HAS DONE THIS APPROXIMATELY 6 TIMES OVER THE PAST 3 YEARS I'VE OWNED THE CAR. IT HAS 115K MILES ON IT. A LOT OF PEOPLE ARE HAVING THE SAME ISSUE AND SUPPOSEDLY IT IS THE HCU. I HAVE NOT GOTTEN IT FIXED YET DUE TO THE PRICE AND AVAILABILITY OF THE PART. *TR
NHTSA ODI #10929499
79,000 miles · Nov 29, 2016
Service BrakesCrash
WHILE DRIVING ON THE HIGHWAY DURING RUSH HOUR TRAFFIC STOPPED AHEAD OF ME. I APPLIED THE BRAKES TO STOP AND THE PEDAL WENT TO THE FLOOR AND ACTIVATED THE ANTILOCK BRAKES. THIS DID NOT PROVIDE ANY SIGNIFICANT BRAKING AND I REAR ENDED THE TRUCK IN FRONT OF ME. ABOUT 2 MONTHS PRIOR I HIT A DRAINAGE GRATE AND UPON APPLYING THE BRAK…
Read full complaint
WHILE DRIVING ON THE HIGHWAY DURING RUSH HOUR TRAFFIC STOPPED AHEAD OF ME. I APPLIED THE BRAKES TO STOP AND THE PEDAL WENT TO THE FLOOR AND ACTIVATED THE ANTILOCK BRAKES. THIS DID NOT PROVIDE ANY SIGNIFICANT BRAKING AND I REAR ENDED THE TRUCK IN FRONT OF ME. ABOUT 2 MONTHS PRIOR I HIT A DRAINAGE GRATE AND UPON APPLYING THE BRAKES THERE WAS NO BRAKES. AFTER DRIVING FOR ABOUT 20 MINUTES THE BRAKES FELT NORMAL AFTER APPLYING THE BRAKES HARD A COUPLE OF TIMES. TOOK THE CAR TO THE DEALER AND HAD THE BRAKES CHECKED AND THE ONLY THING FOUND WAS THE ROTORS NEEDED TO BE TURNED. THE CAR HAS ABOUT 79,000 MILES. *TR
NHTSA ODI #10928668
145,000 miles · Nov 28, 2016
Service Brakes
TL* THE CONTACT OWNS A 2009 FORD FUSION. THE CONTACT STATED THAT THE BRAKE PEDAL TRAVELED TO THE FLOORBOARD SEVERAL TIMES WITHOUT WARNING. THE BRAKE CALIPERS AND BRAKE PADS WERE REPLACED MORE THAN TWICE, BUT THE FAILURE CONTINUED. THE CONTACT WAS UNCERTAIN IF THE HCU FAILED. THE MANUFACTURER WAS NOT NOTIFIED. THE VEHICLE WAS NOT…
Read full complaint
TL* THE CONTACT OWNS A 2009 FORD FUSION. THE CONTACT STATED THAT THE BRAKE PEDAL TRAVELED TO THE FLOORBOARD SEVERAL TIMES WITHOUT WARNING. THE BRAKE CALIPERS AND BRAKE PADS WERE REPLACED MORE THAN TWICE, BUT THE FAILURE CONTINUED. THE CONTACT WAS UNCERTAIN IF THE HCU FAILED. THE MANUFACTURER WAS NOT NOTIFIED. THE VEHICLE WAS NOT REPAIRED. THE VIN WAS NOT AVAILABLE. THE APPROXIMATE FAILURE MILEAGE WAS 145,000.
NHTSA ODI #10928256
72,000 miles · Nov 10, 2016
Service Brakes
IMMEDIATELY AFTER A BRAKING SITUATION WHERE THE ABS SYSTEM WAS ACTIVATED, MY BRAKE PEDAL HAD ALMOST NO RESISTANCE AND IT WENT ALL THE WAY TO THE FLOOR TO ACHIEVE MODERATE BRAKING. HAD TO SHIFT TO PARK AND PUMP THE BRAKES TO GET BACK SOME RESISTANCE. IF I HAD NEEDED TO DO ADDITIONAL BRAKING IN THIS SCENARIO I WOULD ASSUME I WOU…
Read full complaint
IMMEDIATELY AFTER A BRAKING SITUATION WHERE THE ABS SYSTEM WAS ACTIVATED, MY BRAKE PEDAL HAD ALMOST NO RESISTANCE AND IT WENT ALL THE WAY TO THE FLOOR TO ACHIEVE MODERATE BRAKING. HAD TO SHIFT TO PARK AND PUMP THE BRAKES TO GET BACK SOME RESISTANCE. IF I HAD NEEDED TO DO ADDITIONAL BRAKING IN THIS SCENARIO I WOULD ASSUME I WOULD HAVE CRASHED DUE TO LACK OF BRAKING ABILITY. CAR HAS 72000 MILES ON IT CURRENTLY AND THIS PROBLEM HAS BEEN EXPERIENCED PROBABLY 5 TIMES IN THE PAST YEAR. AFTER MAYBE 20 MINUTES OF ADDITIONAL STOP AND GO DRIVING, THE BRAKES APPEAR TO BE NORMAL. THIS HAPPENED ON A CITY STREET AND THE ABS WAS ACTIVATED DUE TO BRAKING WHEN TIRE WENT OVER A SMOOTH METAL MANHOLE COVER.
NHTSA ODI #10925296
45,000 miles · Nov 3, 2016
Service Brakes
TL* THE CONTACT OWNS A 2009 FORD FUSION. WHILE DRIVING AT ANY SPEED, THE VEHICLE DROVE OVER A BUMP. THE CONTACT DEPRESSED THE BRAKE PEDAL AND IT TRAVELED TO THE FLOORBOARD BEFORE THE VEHICLE STOPPED. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE VEHICLE WAS TOWED TO THE DEALER. THE FAILURE WAS DUPLICATED; HOWEVER, THE VEHIC…
Read full complaint
TL* THE CONTACT OWNS A 2009 FORD FUSION. WHILE DRIVING AT ANY SPEED, THE VEHICLE DROVE OVER A BUMP. THE CONTACT DEPRESSED THE BRAKE PEDAL AND IT TRAVELED TO THE FLOORBOARD BEFORE THE VEHICLE STOPPED. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE VEHICLE WAS TOWED TO THE DEALER. THE FAILURE WAS DUPLICATED; HOWEVER, THE VEHICLE WAS NOT DIAGNOSED. THE FAILURE RECURRED NUMEROUS TIMES. THE MANUFACTURER WAS NOTIFIED. THE VEHICLE WAS NOT REPAIRED. THE VIN WAS UNKNOWN. THE APPROXIMATE FAILURE MILEAGE WAS 45,000.
NHTSA ODI #10923968
Mileage unknown · Oct 22, 2016
Air BagsService Brakes
SUMMER OF 2016 THE WARNING LIGHT FOR AIR BAG CAME ON. OCT 20 2016 TOOK THE CAR INTO DEALERSHIP. THEY HAD THE CAR FOR TWO DAYS, NEVER MENTIONED ANY RECALL, NEEDED THE CAR FOR THE WEEKEND, THEY WANTED ME TO PAY FOR THE PART IN ADVANCE BEFORE ORDERING IT. DO NOT RECALL HOW WARNING LIGHT APPEARED ON THE THE DASH BOARD.
NHTSA ODI #10918018
75,000 miles · Oct 20, 2016
Service Brakes
IN SITUATIONS WHERE A DRIVER IS BRAKING AND YOUR ABS BECOMES ENABLED, THERE IS A CHANCE THAT VALVES INSIDE THE HYDRAULIC CONTROL UNIT (HCU) MAY STICK, GREATLY REDUCING PRESSURE SENT TO THE CALIPER/BRAKE. THE VALVES MAY CONTINUE TO BE STUCK UNTIL EITHER THE ABS IS REENGAGED OR UNTIL THE VALVES UNSTICK THEMSELVES, BETWEEN PERIODS …
Read full complaint
IN SITUATIONS WHERE A DRIVER IS BRAKING AND YOUR ABS BECOMES ENABLED, THERE IS A CHANCE THAT VALVES INSIDE THE HYDRAULIC CONTROL UNIT (HCU) MAY STICK, GREATLY REDUCING PRESSURE SENT TO THE CALIPER/BRAKE. THE VALVES MAY CONTINUE TO BE STUCK UNTIL EITHER THE ABS IS REENGAGED OR UNTIL THE VALVES UNSTICK THEMSELVES, BETWEEN PERIODS OF HOURS OR WEEKS. WHILE THE VALVES ARE STUCK, BRAKE PEDDLES WILL FEEL EXTREMELY SPONGY AND ARE REQUIRED TO BE PRESSED TO THE FLOOR TO ACTUALLY HAVE THE DESIRED EFFECT OF SLOWING THE CAR. EVEN WHEN PRESSED ALL THE WAY DOWN, THE EFFECTS OF BRAKING ARE SEVERELY DIMINISHED WHEN COMPARED TO PROPERLY WORKING BRAKES. REDUCED BRAKING EFFECTIVENESS IS OBVIOUSLY EXTREMELY DANGEROUS FOR DRIVERS AND COULD, EVEN DURING CLEAR CONDITIONS, CAUSE AN ACCIDENT. REPLACEMENT OF THE HCU COSTS SEVERAL HUNDRED DOLLARS AND IS ULTIMATELY A TEMPORARY FIX, AS THE ISSUE WILL EVENTUALLY REOCCUR.
NHTSA ODI #10917606
Official recalls
6Mar 10, 2021
Ford Motor Company (Ford) is recalling certain 2007-2011 Ranger, 2006-2012 Fusion, Lincoln Zephyr, Lincoln MKZ, 2006-2011 Mercury Milan, 2007-2010 Ford Edge, and Lincoln MKX vehicles. The driver's side air bag inflator may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will replace the driver-side airbag inflator or module with an alternate one, free of charge. Owner notification letters were mailed on April 9, 2021 for the passenger side, and November 14, 2022 for the driver side. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S12.
Feb 16, 2021
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Additional source detail variants (3)
Air Bags:frontal:passenger Side:inflator Module
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Air Bags:frontal:driver Side:inflator Module
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Air Bags:frontal
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Dec 18, 2019
Ford Motor Company (Ford) is recalling certain 2006-2010 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ vehicles. The valves within the ABS Hydraulic Control Units (HCU) may react with brake fluids containing specific corrosion preventative additives. This reaction may cause the valves to not close properly.
Consequence & remedy
Consequence: If the valves do not properly close, additional brake pedal travel may be required to stop the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will flush the brake system with DOT 4 fluid and install a new brake fluid reservoir cap. In addition, the HCU will be tested to detect a possible stuck valve condition, replacing the HCU as necessary. All services will be performed free of charge. The recall began April 1, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S54.
Jan 11, 2018
Ford Motor Company (Ford) is recalling certain 2013 Ford Mustang vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is recalling certain 2010 Ford Edge, Fusion, Mustang and Ranger, Lincoln MKX and Zephyr/MKZ, and Mercury Milan vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Ford is also recalling certain 2009 Ford Edge, Fusion, Mustang and Ranger, Lincoln MKX and Zephyr/MKZ, and Mercury Milan vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
Jan 10, 2017
Ford Motor Company (Ford) is recalling certain 2012 Ford Fusion and Mustang and Lincoln Zephyr and MKZ vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Ford is recalling certain 2009 Ford Ranger, Edge, Fusion and Mustang, Lincoln MKX, MKZ and Zephyr and Mercury Milan vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Ford is recalling certain 2007-2008 Ford Ranger, Edge and Lincoln MKX, 2006-2008 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ, 2005-2008 Ford Mustang and 2005-2006 Ford GT vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Interim letters informing owners of the recall and that parts are not yet available began mailing March 1, 2017. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
May 31, 2016
Ford Motor Company (Ford) is recalling certain model year 2007-2011 Ford Ranger vehicles, 2006-2011 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2007-2010 Ford Edge, Lincoln MKX vehicles, 2005-2006 Ford GT vehicles, and 2005-2011 Ford Mustang vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Ford is recalling certain model year 2007-2008 Ford Ranger, Edge and Lincoln MKX vehicles, 2006-2008 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2005-2006 Ford GT vehicles and 2005-2008 Ford Mustang vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Any vehicle not included in "Zone A", or "Zone B" is not included in the safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Ford mailed interim letters informing owners that parts are not yet available on July 15, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4EA18002 · Extended Braking Distance
Opened Apr 18, 2018 · Closed Jan 15, 2021
Status: closed (inferred from source dates) · Service Brakes, Air:antilock:control Unit/module
On April 18, 2018, the Office of Defects Investigation (ODI) opened Engineering Analysis (EA) 18-002 to investigate reports of braking concerns in model year (MY) 2006-12 Ford Fusion and Lincoln MKZ, and MY 2006-11 Mercury Milan vehicles manufactured with Continental Automotive System?s ABS hydraulic control units (HCUs). Complainants report that after an ABS braking event (initiated by slippery or uneven surfaces) the brake pedal moved towards the floor and the vehicle stopping distance increased beyond driver expectations.Inside the HCU are four hydraulic normally closed (NC) valves with zinc-coated moving armatures that control the flow of brake fluid. Unstable brake fluid can degrade over time, allow the brake fluid to gel, and corrosion to form on the armatures. The high-viscosity gelation and corrosion can cause the armatures to become stuck (open). In some cases, braking returns to normal when the armature(s) subsequently become unstuck. The intermittent condition proves difficult to diagnose with complainants reporting having (non-HCU) repairs conducted only to have the condition return.During the investigation, 14 HCUs from complaint vehicles were recovered, including seven from reported crashes. NHTSA?s Vehicle Research and Test Center (VRTC) disassembled the HCUs, removed the four NC valves in each, and confirmed 22 of the 56 NC valves contained stuck armatures. On seven of the 14 HCUs, both front wheel armatures were stuck, on nine of the 14 HCUs two or three armatures were stuck. And 52 of the 56 NC armatures exhibited corrosion of the zinc coating. Forces required to extract stuck armatures from the valve sleeve were measured to range from 1.1 to 18.0 lbs. VRTC also conducted ABS braking tests on a variety of test surfaces that showed HCU failures cause increases in pedal travel and braking distances. Testing also showed that if the driver was able to apply four times the brake pedal force and two times the brake pedal travel, then high-vehicle decelerations could be achieved, however, single or multiple wheel lockups were also occurring.Based on Ford?s response to ODI?s July 20, 2018 information request letter, and complainants' reports to NHTSA, ODI identified a population of vehicles with an elevated level of field failure compared to vehicles produced both before and after.Further evaluation of Ford?s response identified that the brake fluid used to produce these vehicles, a specific formulation of a DOT3 fluid provided by CCI Corporation between February 2006 and July 2009, differed from the brake fluid used in other vehicle populations. ODI used the correlation of fluid specification and elevated field failures to identify a vehicle population exhibiting a defect trend. The complaints, crashes and injuries cited above, and the 14 recovered HCUs involve vehicles from this population.On December 18, 2019, Ford submitted safety recall (19V-904) to remedy HCU failures on the MY 2006-2010 Ford Fusion, Lincoln MKZ, and Mercury Milan vehicles manufactured with the suspect CCI brake fluid formulation. Ford will function test the HCU and replace the DOT 3 brake fluid with an improved DOT 4 brake fluid. If the HCU fails the function test, Ford will install an HCU with a different armature coating (black oxide). HCUs with black oxide coating were fully phased into Ford?s new vehicle production by MY 2016; these HCUs do not appear to be experiencing armature corrosion. ODI notes that the non-recalled EA18-002 subject vehicles, which were manufactured with a different specification brake fluid, did not display an elevated level of field failures like the recalled vehicles.Based on available information, Ford?s rec
PE16017 · Extended Braking Distance
Opened Dec 20, 2016 · Closed May 4, 2018
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
Additional source detail variants (4)
Service Brakes
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
Service Brakes, Hydraulic
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
EA12009 · Floor Mat Interference With Accelerator
Opened Dec 12, 2012 · Closed Jun 12, 2014
Status: closed (inferred from source dates) · Vehicle Speed Control; Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Additional source detail variants (2)
Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Vehicle Speed Control
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
PE10019 · Accel Pedal Interference - Acc Floormat
Opened May 28, 2010 · Closed Jan 11, 2013
Status: closed (inferred from source dates) · Vehicle Speed Control:accelerator Pedal
Unsecured mats may interfere with accelerator pedal return to idle. A heel blocker in the floor pan provides a platform that may lift an unsecured mat into contact with the pedal. Ford introduced new pedals as a running change early in model year (MY) 2010 vehicles. Analysis of complaints received by ODI and Ford show elevated rates of pedal entrapment incidents in MY 2008 through early 2010 production vehicles. Incidents typically occur following hard pedal applications to pass slower traffic or when merging into faster traffic. Drivers allege continued high engine power after releasing the accelerator pedal and difficulty braking, including reports that the incident was controlled by shifting to neutral or turning the engine off. Drivers and service technicians reference observing evidence of mat interference or note unsecured Ford or aftermarket all weather floor mats in post-incident inspections.Based on information gathered during the Preliminary Evaluation the population being investigated has been narrowed to model years 2008 to 2010.This investigation has been upgraded to an engineering analysis on MY 2008 through early-2010 vehicles (produced through September 2009) to further assess the scope, frequency and safety consequences of the alleged defect.The VOQs associated with the opening of this Engineering Analysis are: 10479693, 10415911, 10379562, 10372674, 10345830, 10342572, 10339330, 10335336, 10334211, 10332233, 10331160, 10329659, 10327597, 10320011, 10232027, 10214131
Illustration