IllustrationBREAK PEDAL GOES TO THE FLOOR. THE VEHICLE TAKES LONGER TO STOP. PUMPING THE BREAKS SEVERAL TIMES SEEMS TO FIX THE PROBLEM. THIS IS A RANDOM PROBLEM.
2009 Ford Fusion
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Ford Fusion do not stand out strongly from the model-year median of 1,109.
About this comparison →How this year compares
Owner complaints by model year
Compare all Fusion years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
350–25K
4325–50K
8450–75K
16575–100K
218100–150K
79150K+
624 reports with mileage · 398 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Service Brakes. Review the 473 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 359 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes, Hydraulic. Review the 60 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
65 crash reports5 fire reports25 injury reports
Service Brakes complaints
473 reportsON MULTIPLE OCCASIONS I HAVE HAD DIFFICULTY WITH STOPPING THE VEHICLE REGARDLESS OF THE WEATHER CONDITIONS. I HAVE HAD MY BRAKES CHECKED REPEATEDLY AND BEEN INFORMED THAT MY PADS, ROTORS, MASTER CYLINDER ARE ALL IN GREAT CONDITION. I HAVE HAD THE BRAKES BLED, BRAKE FLUID CHANGE AND IT HAS NOT RECTIFIED THE ISSUE. ON MORE THAN …
Read full complaint
ON MULTIPLE OCCASIONS I HAVE HAD DIFFICULTY WITH STOPPING THE VEHICLE REGARDLESS OF THE WEATHER CONDITIONS. I HAVE HAD MY BRAKES CHECKED REPEATEDLY AND BEEN INFORMED THAT MY PADS, ROTORS, MASTER CYLINDER ARE ALL IN GREAT CONDITION. I HAVE HAD THE BRAKES BLED, BRAKE FLUID CHANGE AND IT HAS NOT RECTIFIED THE ISSUE. ON MORE THAN ONE OCCASION I HAVE EITHER ENDED UP ON THE SIDE OF THE HIGHWAY OR ALMOST HIT ANOTHER VEHICLE TRYING TO STOP. THERE IS NO FOREWARNING AS TO WHEN THIS HAPPENS. THE BRAKE PAD IS EXTREMELY SPONGY AND AT TIMES WHEN BEING PUSHED GOES NEARLY TO THE FLOOR. THIS HAS HAPPENED ON THE STREET, ON THE HIGHWAY, THE WORSE AND MOST SCARIEST INCIDENT WAS DRIVING HIGHWAY 77-SOUTH THROUGH WV, GOING THROUGH THE MOUNTAINS. I HAVE COUNTED 13 INCIDENTS OF THIS OVER THE PAST YEAR. THERE HAVE BEEN MORE INCIDENTS OVER THE SPAN OF 3 YEARS BUT ON EACH PREVIOUS OCCASION I WAS TOLD THAT AIR GETS IN THE BRAKE LINE AND TO PUMP THE BRAKES. THIS CLEARLY HAS NOT ELEVATED THE ISSUE. THE MOST RECENT EVALUATION BY A MECHANIC ASSURED ME THAT MY BRAKES THEMSELVES WERE IN GOOD CONDITION.
DRIVING THE OTHER DAY I LOST BRAKES AND ALMOST HAD AN ACCIDENT WITH ANOTHER VEHICLE. THE BRAKE LIGHT CAME ON ALONG WITH THE SERVICE LIGHT. WHICH IS STILL ON. DRIVE HOME VARIOUSLY IN LOW GEAR WHEN NEEDED. WHEN IN LOW GEAR I HEARD A CONSTANT GRINDING NOISE. STILL PATIENTLY WAITING ON MY TAKATA AIR BAG REPLACEMENT THRU FORD. THIS V…
Read full complaint
DRIVING THE OTHER DAY I LOST BRAKES AND ALMOST HAD AN ACCIDENT WITH ANOTHER VEHICLE. THE BRAKE LIGHT CAME ON ALONG WITH THE SERVICE LIGHT. WHICH IS STILL ON. DRIVE HOME VARIOUSLY IN LOW GEAR WHEN NEEDED. WHEN IN LOW GEAR I HEARD A CONSTANT GRINDING NOISE. STILL PATIENTLY WAITING ON MY TAKATA AIR BAG REPLACEMENT THRU FORD. THIS VEHICLE IS NEW TO ME AND I HAVEN'T MADE MY FIRST PAYMENT YET. ONLY HAS 40K FOR MILEAGE. AS IS COMMON WITH MOST FORD CATS. I ASKS EXPERIENCED SURGES IN THE VAST. MY LAY CAST WAS AN 04 TAURUS.
TL* THE CONTACT OWNS A 2009 FORD FUSION. WHILE ATTEMPTING TO STOP THE VEHICLE, THE BRAKE PEDAL TRAVELED TO THE FLOORBOARD WHEN IT WAS DEPRESSED. THE FAILURE OCCURRED ON SEVERAL OCCASIONS. AN INDEPENDENT MECHANIC WAS ABLE TO DUPLICATE THE FAILURE, BUT WAS UNABLE TO DETERMINE THE CAUSE. THE FAILURE WAS NOT REPAIRED. THE LOCAL DEAL…
Read full complaint
TL* THE CONTACT OWNS A 2009 FORD FUSION. WHILE ATTEMPTING TO STOP THE VEHICLE, THE BRAKE PEDAL TRAVELED TO THE FLOORBOARD WHEN IT WAS DEPRESSED. THE FAILURE OCCURRED ON SEVERAL OCCASIONS. AN INDEPENDENT MECHANIC WAS ABLE TO DUPLICATE THE FAILURE, BUT WAS UNABLE TO DETERMINE THE CAUSE. THE FAILURE WAS NOT REPAIRED. THE LOCAL DEALER (STERMAN AND LARKIN FORD IN PITTSBURGH, PA) WAS NOTIFIED OF THE FAILURE. THE MANUFACTURER WAS NOT NOTIFIED. THE FAILURE MILEAGE WAS 106,000.
VERY SOFT BRAKES. - THE CAR KEPT EXPERIENCING SOFT BRAKES AFTER THE ABS WOULD ENGAGE OR IF THE CAR HIT A POT HOLE OF SOLID BUMP IN THE ROAD. NOT ALL THE TIMES BUT FAIRLY OFTEN. WE REPLACED THE MASTER CYLINDER IN 2016 AND THE BRAKE PADS RECENTLY AS WELL. IN DEC OF 2017, I WAS GOING ABOUT 25MPH WHILE APPROACHING THE EXIT OF OUR NE…
Read full complaint
VERY SOFT BRAKES. - THE CAR KEPT EXPERIENCING SOFT BRAKES AFTER THE ABS WOULD ENGAGE OR IF THE CAR HIT A POT HOLE OF SOLID BUMP IN THE ROAD. NOT ALL THE TIMES BUT FAIRLY OFTEN. WE REPLACED THE MASTER CYLINDER IN 2016 AND THE BRAKE PADS RECENTLY AS WELL. IN DEC OF 2017, I WAS GOING ABOUT 25MPH WHILE APPROACHING THE EXIT OF OUR NEIGHBORHOOD. THERE WAS A SMALL PATCH OF ICE & WATER. I WAS BRAKING FOR A STOP WHEN THE CAR CROSSED THE PATCH. THE ABS ENGAGED. FROM THAT MOMENT ON FOR ABOUT 2 WEEKS THE BRAKES WOULD GO TO THE FLOOR BEFORE THEY WOULD SLOW THE CAR TO A STOP. THEN IT CLEARED UP. ON SUNDAY APRIL 22 AROUND 1AM, WE WERE DRIVING THROUGH A TOWN ON OUR WAY BACK FROM PICKING UP OUR SON. IT HAD BEEN RAINING STEADY FOR SEVERAL HOURS. MY HUSBAND WAS DRIVING LESS THAN 35MPH APPROACHING A TRAFFIC LIGHT THAT HAD JUST TURNED YELLOW. HE TRIED TO STOP FOR THE LIGHT. THE ABS ENGAGED BUT THE CAR DID NOT STOP. THE LIGHT TURNED RED BEFORE WE GOT TO THE INTERSECTION BUT THE CAR WAS NOT STOPPING. WE RAN THE RED LIGHT. THE CAR DID FINELY SLOW DOWN TO AN ALMOST STOP BUT WE WERE ALREADY THROUGH THE INTERSECTION. LUCKILY THERE WERE NO OTHER CARS AROUND AT THE TIME BUT FROM THAT MOMENT ON THE BRAKES HAVE BEEN SOFT. AFTER FINISHING OUR TRIP HOME ABOUT 300 PLUS MILES AND GOING TO THE STORE WHERE WE LIVE ABOUT 5 MILES, WE ARE AFRAID OF DRIVING THE CAR ANYMORE. IT TAKES TOO LONG TO STOP AND IF SOMEONE STOPPED QUICKLY WHILE IN FRONT OF US OR IF SOMETHING RAN OUT IN FRONT OF US WHILE DRIVING, WE DON'T BELIEVE WE COULD STOP QUICKLY ENOUGH; SAFELY.
I HAD TO HIT THE BRAKES REALLY HARD AS SOMEONE PULLED OUT IN FRONT OF ME. MOMENTS LATER THE BRAKE PEDAL GOES STRAIGHT TO THE FLOOR. THE HCU IS STUCK. THE BRAKES ARE SOFT AND IT TAKES SIGNIFICANTLY LONGER TO STOP.
TAKATA INFLATORS: I AM HAVING A VERY HARD TIME BREAKING WHEN I NEED TO BREAK. OVER THE PAST WINTER, I'VE SLID THROUGH SEVERAL RED LIGHTS AND HAD TO BLOW ON MY HORN TO ALERT ON COMING TRAFFIC TO STOP. I'VE BEEN TOLD BY THE SHOPS THAT I SHOULD NOT EVEN BE DRIVING MY CAR. THIS IS VERY DANGEROUS AND OVERWHELMING. IVE CAME OUT OF A …
Read full complaint
TAKATA INFLATORS: I AM HAVING A VERY HARD TIME BREAKING WHEN I NEED TO BREAK. OVER THE PAST WINTER, I'VE SLID THROUGH SEVERAL RED LIGHTS AND HAD TO BLOW ON MY HORN TO ALERT ON COMING TRAFFIC TO STOP. I'VE BEEN TOLD BY THE SHOPS THAT I SHOULD NOT EVEN BE DRIVING MY CAR. THIS IS VERY DANGEROUS AND OVERWHELMING. IVE CAME OUT OF A LOT OF MONEY ON BREAKS, PADS, MASTER CYLINDER REPAIRS,ETC. AND WOULD JUST LIKE TO BE ABLE TO DRIVE NORMALLY. I HAVE TO PRESS ALL THE WAY DOWN TO STOP MY CAR AT ALL TIMES. MY BREAKS NEVER FEEL NORMAL. THIS HAS BEEN GOING ON FOR A LITTLE OVER A YEAR NOW
WHILE APPROACHING AN INTERSECTION, BRAKES WERE APPLIED FOR A RED LIGHT WHICH LOST ALL HYDRAULIC PRESSURE AFTER FRONT RIGHT WHEEL WENT OVER A POTHOLE. TO FULLY STOP THE VEHICLE, THE BRAKE PEDAL HAD TO BE PUSHED FULLY TO THE FLOOR. SUBSEQUENT DRIVING SHOWED VIRTUALLY NO RETURN OF HYDRAULIC PRESSURE IN THE BRAKES. THIS OCCURRED WIT…
Read full complaint
WHILE APPROACHING AN INTERSECTION, BRAKES WERE APPLIED FOR A RED LIGHT WHICH LOST ALL HYDRAULIC PRESSURE AFTER FRONT RIGHT WHEEL WENT OVER A POTHOLE. TO FULLY STOP THE VEHICLE, THE BRAKE PEDAL HAD TO BE PUSHED FULLY TO THE FLOOR. SUBSEQUENT DRIVING SHOWED VIRTUALLY NO RETURN OF HYDRAULIC PRESSURE IN THE BRAKES. THIS OCCURRED WITHIN MONTHS OF HAVING BRAKE PADS, ROTORS, FLUID, AND MASTER CYLINDER INSPECTED BY FORD-BRANDED DEALER.
INITIALLY, ON A WET CITY STREET AT 45 MPH, THE BRAKES FAILED WITH THE PEDAL GOING TO THE FLOOR. PUMPING THE BRAKE SEEMED TO RESTORE THE BRAKES. SEVERAL WEEKS LATER, TRAVELLING AT 35 MPH ON A DRY CITY STREET, MY BRAKES FAILED AS I APPROACHED A YELLOW TRAFFIC LIGHT. WITH THE BRAKE PEDAL DEPRESSED TO THE FLOOR, I TRAVELLED THROUGH …
Read full complaint
INITIALLY, ON A WET CITY STREET AT 45 MPH, THE BRAKES FAILED WITH THE PEDAL GOING TO THE FLOOR. PUMPING THE BRAKE SEEMED TO RESTORE THE BRAKES. SEVERAL WEEKS LATER, TRAVELLING AT 35 MPH ON A DRY CITY STREET, MY BRAKES FAILED AS I APPROACHED A YELLOW TRAFFIC LIGHT. WITH THE BRAKE PEDAL DEPRESSED TO THE FLOOR, I TRAVELLED THROUGH THE INTERSECTION ON A RED LIGHT. I TOOK A BACK ROAD TO GET BACK TO MY POINT OF ORIGIN AND WAS UNABLE TO STOP FOR ANY OF THE STOP SIGNS. THE MASTER CYLINDER AND THE BOOSTER WERE REPLACED BUT DID NOT SOLVE THE PROBLEM. AFTER WEEKS OF BEING CHECKED OUT BY A FORD DEALER, THE VEHICLE WAS RETURNED TO ME BUT THE BRAKES ARE STILL SOFT AND FEEL UNSAFE. IT SOMETIMES FEELS LIKE THE CAR ACCELERATES AFTER I DEPRESSED THE BRAKE PEDAL BEFORE THE BRAKING KICKS IN. A LONGER STOPPING DISTANCE IS REQUIRED.
ON THREE SEPARATE OCCASIONS OVER THE PAST 4-5 YEARS, MY BRAKES HAVE GONE "SOFT". THE FIRST TIME WAS THE SECOND I STARTED THE CAR AND BEGAN TO LEAVE MY PARKING SPOT, THE SECOND TIME WAS AFTER I HIT A POT HOLE ON REGULAR STREETS, AND THE 3RD TIME WAS AFTER I HAD TO BRAKE SUDDENLY ON THE HIGHWAY. ALL THREE TIMES IT FELT LIKE I HA…
Read full complaint
ON THREE SEPARATE OCCASIONS OVER THE PAST 4-5 YEARS, MY BRAKES HAVE GONE "SOFT". THE FIRST TIME WAS THE SECOND I STARTED THE CAR AND BEGAN TO LEAVE MY PARKING SPOT, THE SECOND TIME WAS AFTER I HIT A POT HOLE ON REGULAR STREETS, AND THE 3RD TIME WAS AFTER I HAD TO BRAKE SUDDENLY ON THE HIGHWAY. ALL THREE TIMES IT FELT LIKE I HAD TO PUSH MY BRAKE ENTIRELY TO THE FLOOR TO STOP. THE LAST TIME RESULTED IN SUCH EXTENDED BRAKING TIMES, THAT I HAD TO SWERVE TO AVOID HITTING THE PERSON IN FRONT OF ME. THE FIRST TIME DID NOT LAST VERY LONG, BUT THE OTHER TWO TIMES REQUIRED TIME AND A LOT OF PUMPING THE BRAKES TO MAKE THE BRAKE FEEL NORMAL AGAIN. I HAVE NOT HAD TO TAKE IT IN TO THE MECHANIC AND I DO NOT HAVE INSURANCE OR POLICE REPORTS FOR THE INCIDENTS. I BELIEVE THIS PROBLEM MATCHES THE CURRENT OPEN INVESTIGATION (NHTSA ACTION NUMBER PE16017)
Official recalls
621V158000 · Air Bags:frontal:driver Side:inflator Module
Mar 10, 2021
Ford Motor Company (Ford) is recalling certain 2007-2011 Ranger, 2006-2012 Fusion, Lincoln Zephyr, Lincoln MKZ, 2006-2011 Mercury Milan, 2007-2010 Ford Edge, and Lincoln MKX vehicles. The driver's side air bag inflator may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will replace the driver-side airbag inflator or module with an alternate one, free of charge. Owner notification letters were mailed on April 9, 2021 for the passenger side, and November 14, 2022 for the driver side. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S12.
21V081000 · Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
Feb 16, 2021
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Additional source detail variants (3)
Air Bags:frontal:passenger Side:inflator Module
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Air Bags:frontal:driver Side:inflator Module
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Air Bags:frontal
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
19V904000 · Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
Dec 18, 2019
Ford Motor Company (Ford) is recalling certain 2006-2010 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ vehicles. The valves within the ABS Hydraulic Control Units (HCU) may react with brake fluids containing specific corrosion preventative additives. This reaction may cause the valves to not close properly.
Consequence & remedy
Consequence: If the valves do not properly close, additional brake pedal travel may be required to stop the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will flush the brake system with DOT 4 fluid and install a new brake fluid reservoir cap. In addition, the HCU will be tested to detect a possible stuck valve condition, replacing the HCU as necessary. All services will be performed free of charge. The recall began April 1, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S54.
18V046000 · Air Bags:frontal:passenger Side:inflator Module
Jan 11, 2018
Ford Motor Company (Ford) is recalling certain 2013 Ford Mustang vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is recalling certain 2010 Ford Edge, Fusion, Mustang and Ranger, Lincoln MKX and Zephyr/MKZ, and Mercury Milan vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Ford is also recalling certain 2009 Ford Edge, Fusion, Mustang and Ranger, Lincoln MKX and Zephyr/MKZ, and Mercury Milan vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
17V024000 · Air Bags:frontal:passenger Side:inflator Module
Jan 10, 2017
Ford Motor Company (Ford) is recalling certain 2012 Ford Fusion and Mustang and Lincoln Zephyr and MKZ vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Ford is recalling certain 2009 Ford Ranger, Edge, Fusion and Mustang, Lincoln MKX, MKZ and Zephyr and Mercury Milan vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Ford is recalling certain 2007-2008 Ford Ranger, Edge and Lincoln MKX, 2006-2008 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ, 2005-2008 Ford Mustang and 2005-2006 Ford GT vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Interim letters informing owners of the recall and that parts are not yet available began mailing March 1, 2017. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
16V384000 · Air Bags:frontal:passenger Side:inflator Module
May 31, 2016
Ford Motor Company (Ford) is recalling certain model year 2007-2011 Ford Ranger vehicles, 2006-2011 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2007-2010 Ford Edge, Lincoln MKX vehicles, 2005-2006 Ford GT vehicles, and 2005-2011 Ford Mustang vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Ford is recalling certain model year 2007-2008 Ford Ranger, Edge and Lincoln MKX vehicles, 2006-2008 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2005-2006 Ford GT vehicles and 2005-2008 Ford Mustang vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Any vehicle not included in "Zone A", or "Zone B" is not included in the safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Ford mailed interim letters informing owners that parts are not yet available on July 15, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4EA18002 · Extended Braking Distance
Opened Apr 18, 2018 · Closed Jan 15, 2021
Status: closed (inferred from source dates) · Service Brakes, Air:antilock:control Unit/module
On April 18, 2018, the Office of Defects Investigation (ODI) opened Engineering Analysis (EA) 18-002 to investigate reports of braking concerns in model year (MY) 2006-12 Ford Fusion and Lincoln MKZ, and MY 2006-11 Mercury Milan vehicles manufactured with Continental Automotive System?s ABS hydraulic control units (HCUs). Complainants report that after an ABS braking event (initiated by slippery or uneven surfaces) the brake pedal moved towards the floor and the vehicle stopping distance increased beyond driver expectations.Inside the HCU are four hydraulic normally closed (NC) valves with zinc-coated moving armatures that control the flow of brake fluid. Unstable brake fluid can degrade over time, allow the brake fluid to gel, and corrosion to form on the armatures. The high-viscosity gelation and corrosion can cause the armatures to become stuck (open). In some cases, braking returns to normal when the armature(s) subsequently become unstuck. The intermittent condition proves difficult to diagnose with complainants reporting having (non-HCU) repairs conducted only to have the condition return.During the investigation, 14 HCUs from complaint vehicles were recovered, including seven from reported crashes. NHTSA?s Vehicle Research and Test Center (VRTC) disassembled the HCUs, removed the four NC valves in each, and confirmed 22 of the 56 NC valves contained stuck armatures. On seven of the 14 HCUs, both front wheel armatures were stuck, on nine of the 14 HCUs two or three armatures were stuck. And 52 of the 56 NC armatures exhibited corrosion of the zinc coating. Forces required to extract stuck armatures from the valve sleeve were measured to range from 1.1 to 18.0 lbs. VRTC also conducted ABS braking tests on a variety of test surfaces that showed HCU failures cause increases in pedal travel and braking distances. Testing also showed that if the driver was able to apply four times the brake pedal force and two times the brake pedal travel, then high-vehicle decelerations could be achieved, however, single or multiple wheel lockups were also occurring.Based on Ford?s response to ODI?s July 20, 2018 information request letter, and complainants' reports to NHTSA, ODI identified a population of vehicles with an elevated level of field failure compared to vehicles produced both before and after.Further evaluation of Ford?s response identified that the brake fluid used to produce these vehicles, a specific formulation of a DOT3 fluid provided by CCI Corporation between February 2006 and July 2009, differed from the brake fluid used in other vehicle populations. ODI used the correlation of fluid specification and elevated field failures to identify a vehicle population exhibiting a defect trend. The complaints, crashes and injuries cited above, and the 14 recovered HCUs involve vehicles from this population.On December 18, 2019, Ford submitted safety recall (19V-904) to remedy HCU failures on the MY 2006-2010 Ford Fusion, Lincoln MKZ, and Mercury Milan vehicles manufactured with the suspect CCI brake fluid formulation. Ford will function test the HCU and replace the DOT 3 brake fluid with an improved DOT 4 brake fluid. If the HCU fails the function test, Ford will install an HCU with a different armature coating (black oxide). HCUs with black oxide coating were fully phased into Ford?s new vehicle production by MY 2016; these HCUs do not appear to be experiencing armature corrosion. ODI notes that the non-recalled EA18-002 subject vehicles, which were manufactured with a different specification brake fluid, did not display an elevated level of field failures like the recalled vehicles.Based on available information, Ford?s rec
PE16017 · Extended Braking Distance
Opened Dec 20, 2016 · Closed May 4, 2018
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
Additional source detail variants (4)
Service Brakes
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
Service Brakes, Hydraulic
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
EA12009 · Floor Mat Interference With Accelerator
Opened Dec 12, 2012 · Closed Jun 12, 2014
Status: closed (inferred from source dates) · Vehicle Speed Control; Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Additional source detail variants (2)
Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Vehicle Speed Control
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
PE10019 · Accel Pedal Interference - Acc Floormat
Opened May 28, 2010 · Closed Jan 11, 2013
Status: closed (inferred from source dates) · Vehicle Speed Control:accelerator Pedal
Unsecured mats may interfere with accelerator pedal return to idle. A heel blocker in the floor pan provides a platform that may lift an unsecured mat into contact with the pedal. Ford introduced new pedals as a running change early in model year (MY) 2010 vehicles. Analysis of complaints received by ODI and Ford show elevated rates of pedal entrapment incidents in MY 2008 through early 2010 production vehicles. Incidents typically occur following hard pedal applications to pass slower traffic or when merging into faster traffic. Drivers allege continued high engine power after releasing the accelerator pedal and difficulty braking, including reports that the incident was controlled by shifting to neutral or turning the engine off. Drivers and service technicians reference observing evidence of mat interference or note unsecured Ford or aftermarket all weather floor mats in post-incident inspections.Based on information gathered during the Preliminary Evaluation the population being investigated has been narrowed to model years 2008 to 2010.This investigation has been upgraded to an engineering analysis on MY 2008 through early-2010 vehicles (produced through September 2009) to further assess the scope, frequency and safety consequences of the alleged defect.The VOQs associated with the opening of this Engineering Analysis are: 10479693, 10415911, 10379562, 10372674, 10345830, 10342572, 10339330, 10335336, 10334211, 10332233, 10331160, 10329659, 10327597, 10320011, 10232027, 10214131