NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
896 reports22,000 miles · Feb 19, 2020
Power Train
THE CAR HESITATES WHEN ACCELERATING AND THEN LURCHES FORWARD WHEN IT FINALLY ENGAGES. THE CAR VIBRATES AND SHUTTERS AND FEELS LIKE IT IS GOING TO STALL. WHEN I CHANGE LANES ON THE FREEWAY IT DOES NOT RESPOND AND FEELS LIKE THE ENGINE IS REVVING AND THEN IT KICKS IN AND JUMPS FORWARD. THIS ALSO HAPPENS WHEN I AM SITTING IN TRAF…
Read full complaint
THE CAR HESITATES WHEN ACCELERATING AND THEN LURCHES FORWARD WHEN IT FINALLY ENGAGES. THE CAR VIBRATES AND SHUTTERS AND FEELS LIKE IT IS GOING TO STALL. WHEN I CHANGE LANES ON THE FREEWAY IT DOES NOT RESPOND AND FEELS LIKE THE ENGINE IS REVVING AND THEN IT KICKS IN AND JUMPS FORWARD. THIS ALSO HAPPENS WHEN I AM SITTING IN TRAFFIC. I HAVE TO GIVE LOTS OF ROOM IN FRONT OF ME BECAUSE WHEN I PRESS THE ACCELERATOR IT DOESN'T GO AT FIRST AND THEN LURCHES FORWARD. I'M AFRAID OF GETTING IN AN ACCIDENT. SOMETIMES WHEN I TURN CORNERS IT ALSO SHAKES AND FEELS LIKE IT IS GOING TO STALL. I HAVE HAD THE CLUTCH/TRANSMISSION REPLACED THREE TIMES SO FAR IN THE 28 MONTHS OF OWNERSHIP. FORD REFUSES TO BUY MY CAR BACK EVEN THOUGH THEY KNOW IT IS DEFECTIVE.
NHTSA ODI #11310135
38,000 miles · Feb 16, 2020
Air BagsCrashInjury
I WAS INVOLVED IN AN ACCIDENT AND WAS INJURED ON FEB. 1, 2020. I WAS DRIVING ON STRAIGHT AWAY WHEN AND AN SUV TURNED IN FRONT OF MY VEHICLE AT HIGH SPEED. MY FORD FOCUS STRUCK THE SUV DRIVER SIDE DOOR AND MY FORD FOCUS RIGHT SIDE BUMPER GOT STUCK UNDER THE SUV DRIVER SIDE DOOR. MY AIRBAGS IN MY FORD FOCUS DID NOT DEPLOY, BUT TH…
Read full complaint
I WAS INVOLVED IN AN ACCIDENT AND WAS INJURED ON FEB. 1, 2020. I WAS DRIVING ON STRAIGHT AWAY WHEN AND AN SUV TURNED IN FRONT OF MY VEHICLE AT HIGH SPEED. MY FORD FOCUS STRUCK THE SUV DRIVER SIDE DOOR AND MY FORD FOCUS RIGHT SIDE BUMPER GOT STUCK UNDER THE SUV DRIVER SIDE DOOR. MY AIRBAGS IN MY FORD FOCUS DID NOT DEPLOY, BUT THE SUV AIRBAGS DID DEPLOY.
NHTSA ODI #11309540
46,205 miles · Feb 9, 2020
Fuel/propulsion SystemPower Train
RECALL 18S32 I AM RESPONDING ON BEHALF OF [XXX] WHO HAS BEEN MY SONS GIRLFRIEND FOR 16 YEARS. THE CAR WAS TAKEN TO COLLEY FORD, 1945 AUTO CENTER DR. GLENDORA CA DECEMBER 19,2018 FOR THE RECALL. THE DEALER REPROGRAMMED PCM CLEARED ALL CNDTCS. PARTS WERE NOT AVAILABLE AT THAT TIME. THE CAR WAS RETURNED TO COLLEY FORD ON NOVEMBER …
Read full complaint
RECALL 18S32 I AM RESPONDING ON BEHALF OF [XXX] WHO HAS BEEN MY SONS GIRLFRIEND FOR 16 YEARS. THE CAR WAS TAKEN TO COLLEY FORD, 1945 AUTO CENTER DR. GLENDORA CA DECEMBER 19,2018 FOR THE RECALL. THE DEALER REPROGRAMMED PCM CLEARED ALL CNDTCS. PARTS WERE NOT AVAILABLE AT THAT TIME. THE CAR WAS RETURNED TO COLLEY FORD ON NOVEMBER 11, 2019 FOR THE SAME PROBLEM. COLLEY FORD STATED THEY CAN NOT REPAIR THE CAR UNDER WARRANTY SINCE UNDER THE VIN IT SHOWS A REPAIR WAS ALREADY DONE. TO DATE FORD HAS NOT SENT [XXX] A PARTS ARE AVAILABLE NOTICE. SEE ATTACHED DOCUMENTS. BEST REGARDS, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR
NHTSA ODI #11308051
52,000 miles · Feb 6, 2020
Engine
TL* THE CONTACT OWNS A 2017 FORD FOCUS. THE CONTACT STATED WHILE DRIVING AT VARIOUS SPEEDS, THE VEHICLE STALLED WITHOUT WARNING. THE VEHICLE WAS TAKEN TO GENE LATTA FORD INC 1565 CARLISLE ST, HANOVER, PA 17331 TO BE DIAGNOSED. THE CONTACT WAS INFORMED THE A SOLENOID NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFA…
Read full complaint
TL* THE CONTACT OWNS A 2017 FORD FOCUS. THE CONTACT STATED WHILE DRIVING AT VARIOUS SPEEDS, THE VEHICLE STALLED WITHOUT WARNING. THE VEHICLE WAS TAKEN TO GENE LATTA FORD INC 1565 CARLISLE ST, HANOVER, PA 17331 TO BE DIAGNOSED. THE CONTACT WAS INFORMED THE A SOLENOID NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS INFORMED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 52,000.
NHTSA ODI #11307587
10,000 miles · Feb 3, 2020
EnginePower TrainVehicle Speed Control
A FEW MONTHS AGO, MY CAR STARTED TO SHAKE (IN A JERKING, FORWARD AND BACK MOTION), AND STRUGGLE TO ACCELERATE. IT WOULD MAKE THIS NOISE, LIKE GEARS GRINDING. I TOOK IT TO THE DEALERSHIP TO GET IT FIXED UNDER WARRANTY, AND THEY REPLACED THE CLUTCH. FOR ABOUT A WEEK, IT WAS FINE. THEN IT STARTED TO DO THE SAME THING AGAIN. IT WILL…
Read full complaint
A FEW MONTHS AGO, MY CAR STARTED TO SHAKE (IN A JERKING, FORWARD AND BACK MOTION), AND STRUGGLE TO ACCELERATE. IT WOULD MAKE THIS NOISE, LIKE GEARS GRINDING. I TOOK IT TO THE DEALERSHIP TO GET IT FIXED UNDER WARRANTY, AND THEY REPLACED THE CLUTCH. FOR ABOUT A WEEK, IT WAS FINE. THEN IT STARTED TO DO THE SAME THING AGAIN. IT WILL JERK BACK AND FORTH WHEN I ACCELERATE FROM A COMPLETE STOP (AT A STOPLIGHT FOR EXAMPLE). RECENTLY, I HAVE BEEN LOSING GAS VERY QUICKLY BECAUSE IT WILL GO ALL THE WAY PAST 4RPMS JUST TO GET FROM 0-20MPH. I'M NOT SURE IF THE WARRANTY IS STILL ON IT, BUT IT ONLY HAS 12,000 MILES ON IT. I HAVE ONLY MADE ONE VERY BIG TRIP WITH IT, TO KANSAS AND BACK TO VIRGINIA. IT DOES THIS OFF AND ON EVERY SINGLE TIME I DRIVE IT. I HAVE TO DRIVE ANYWHERE FROM 25 MINUTES TO AN HOUR FOR WORK, SO THIS IS REALLY NOT CONVENIENT TO HAVE. MULTIPLE TIMES I WAS WORRIED IT WOULD BREAK DOWN AS I STRUGGLED TO KEEP IT FROM OVERDOING ITSELF WHILE ACCELERATING. A FEW TIMES, I COULD SMELL SOMETHING LIKE EXHAUST IN THE VENTS. THIS HAS BEEN HAPPENING OVER THE COURSE OF 6 MONTHS AND HAS ONLY GOTTEN WORSE, EVEN AFTER TAKING IT TO THE DEALERSHIP, AND HAVING THEM TELL ME IT WAS "FIXED."
NHTSA ODI #11306746
25,600 miles · Feb 3, 2020
Air BagsCrashInjury
TL* THE CONTACT OWNS A 2017 FORD FOCUS. THE CONTACT STATED THAT WHILE DRIVING AT 35 MPH, A VEHICLE HAD BLOWN THROUGH A RED LIGHT AND COLLIDED DIRECTLY WITH THE FRONT PASSENGER SIDE OF HIS VEHICLE. THE CONTACT STATED THAT HIS AIR BAGS DID NOT DEPLOY UPON IMPACT. THE CONTACT HAD SUSTAINED SEVERAL INJURIES INCLUDING SEVERE WHIPLAS…
Read full complaint
TL* THE CONTACT OWNS A 2017 FORD FOCUS. THE CONTACT STATED THAT WHILE DRIVING AT 35 MPH, A VEHICLE HAD BLOWN THROUGH A RED LIGHT AND COLLIDED DIRECTLY WITH THE FRONT PASSENGER SIDE OF HIS VEHICLE. THE CONTACT STATED THAT HIS AIR BAGS DID NOT DEPLOY UPON IMPACT. THE CONTACT HAD SUSTAINED SEVERAL INJURIES INCLUDING SEVERE WHIPLASH DUE TO HITTING HIS HEAD ON THE DRIVER SIDE WINDOW. HE ALSO SUSTAINED PAIN TO HIS NECK AND SUFFERED SEVERAL CUTS AND BRUISES TO HIS FACE, NECK AND HAND. THE CONTACT WAS TAKEN TO THE HOSPITAL BY HIS FATHER WHERE HE WAS DIAGNOSED AND TREATED FOR HIS INJURIES. THE OTHER DRIVER DID NOT SUSTAIN ANY INJURIES AS A RESULT OF THE ACCIDENT. A POLICE REPORT WAS FILED [XXX]. THE VEHICLE WAS TOWED TO AN INDEPENDENT BODY SHOP WHERE IT REMAINED UNDER INVESTIGATION. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE AND INFORMED THE CONTACT THAT THE VEHICLE WOULD HAVE TO BE TOWED TO A LOCAL DEALER FOR AN INVESTIGATOR TO LOOK INTO THE ACCIDENT. THE FAILURE MILEAGE WAS APPROXIMATELY 25,600. *LN*JB*JS *TR
NHTSA ODI #11306684
64,000 miles · Feb 2, 2020
EngineFuel/propulsion SystemPower Train
OUR CAR WAS LOOKED AT JULY 2019 AND THE RECALL WAS NOT FIXED BUT THEY KNEW ABOUT IT FROM YOUR RECORDS. AND WE HAVE BEEN HAVING TROUBLE ON ACCELERATING SPITTING AND SPUTTERING AND TODAY ME AND MY FAMILY WERE OUT SHOPPING AND WE WERE DRIVING OUT OF THE PARKING LOT AND THE CAR JUST WOULD NOT GO THE GAS WAS NOT WORKING WE COULDNT MO…
Read full complaint
OUR CAR WAS LOOKED AT JULY 2019 AND THE RECALL WAS NOT FIXED BUT THEY KNEW ABOUT IT FROM YOUR RECORDS. AND WE HAVE BEEN HAVING TROUBLE ON ACCELERATING SPITTING AND SPUTTERING AND TODAY ME AND MY FAMILY WERE OUT SHOPPING AND WE WERE DRIVING OUT OF THE PARKING LOT AND THE CAR JUST WOULD NOT GO THE GAS WAS NOT WORKING WE COULDNT MOVE AND WE TURNED IT OFF AND STARTING DRIVING AGAIN AND THE SAME THING HAPPENED AND THE CHECK ENGINE LIGHT WAS ON AND IT WASNT ON BEFORE THIS. I AM VERY MAD THAT THIS RECALL WAS OVER LOOKED BECAUSE MY FAMILYS LIFE COULDNT HAD BEEN TAKEN IF THIS HAPPENED ON A FREEWAY OR INTERSTATE. SO WE HAD TO PAY FOR A TOW TO THE DEALERSHIP JOHNSON CITY FORD, TN 37602 AND THEY WERE CLOSED TODAY BUT TOMORROW I AM GOING TO CONFRONT THEM ABOUT THIS AND IM REACHING OUT TO U GUYS TO INSURE THIS WILL GET FIXED OF NO CHARGE AND FIXED RIGHT! THANK U.
NHTSA ODI #11306596
35 miles · Jan 30, 2020
Vehicle Speed Control
VEHICLE STAYS IN HIGH GEAR, EVEN WHEN PARKED, I TURN THE VEHICLE OFF, THEN BACK ON, AND THE CAR IS STILL IN A HIGH GEAR AND THE ENGINE REVS. ALSO, THE BATTERY DIES AFTER THE CAR IS TURNED OFF FOR EVEN 5 MINUTES.
NHTSA ODI #11303059
Mileage unknown · Jan 29, 2020
Unknown Or Other
MY 2017 FORD FOCUS IS HAVING ISSUES WITH JIDDERING AND JUMPING. IT IS ESPECIALLY WORSE WHEN COMING TO A COMPLETE STOP AND GOING, IT WILL SHAKE AND JUMP. MY CAR IS NOT DAMAGED I JUST KNOW THE 2015 YEARS ARE DOING THE SAME THING AND A RECALL WAS ISSUED. IT DOES THIS JUMPING LIKE THING REGARDLESS CITY STREET OR HIGHWAY IT'S JUST WH…
Read full complaint
MY 2017 FORD FOCUS IS HAVING ISSUES WITH JIDDERING AND JUMPING. IT IS ESPECIALLY WORSE WHEN COMING TO A COMPLETE STOP AND GOING, IT WILL SHAKE AND JUMP. MY CAR IS NOT DAMAGED I JUST KNOW THE 2015 YEARS ARE DOING THE SAME THING AND A RECALL WAS ISSUED. IT DOES THIS JUMPING LIKE THING REGARDLESS CITY STREET OR HIGHWAY IT'S JUST WHEN THE CAR COMES TO A STOP AND GOES AGAIN. IF YOU EASE INTO IT OR FLOOR IT IT DOESN'T MAKE A DIFFERENCE.
NHTSA ODI #11302804
Mileage unknown · Jan 27, 2020
Power Train
VEHICLE SHUTTERS WHEN UP SHIFTING AND DOWNSHIFTING. IT DOES NOT TRANSITION SMOOTHLY FROM GEAR TO GEAR. ALSO, IT WILL DOWNSHIFT AT HIGH SPEEDS INCREASING THE RPMS DRASTICALLY!
NHTSA ODI #11302168
Official recalls
10Jun 9, 2026
Ford Motor Company (Ford) is recalling certain 2012-2018 Focus vehicles previously repaired incorrectly under recall number 18V735. The Canister Purge Valve (CPV) may malfunction, causing the engine to stall unexpectedly while driving.
Consequence & remedy
Consequence: An engine that stalls while driving increases the risk of a crash.
Remedy: Dealers will update the powertrain control module (PCM) software, free of charge. Owner notification letters were mailed July 29, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S40. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6,2026.
Jun 9, 2026
Ford Motor Company (Ford) is recalling certain 2015-2018 Focus and 2013-2016 Fusion vehicles previously repaired incorrectly under recall numbers 18V169 and 18V845. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.
Consequence & remedy
Consequence: A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.
Remedy: Dealers will update the software, free of charge. Additionally, dealers will inspect Focus vehicles and replace the clutch assembly as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed August 5, 2026. Additional letters will be sent once the remedy is available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S43. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6,2026.
Jan 15, 2026
Ford Motor Company (Ford) is recalling certain 2013-2018 Focus, 2013-2019 Escape, and 2015-2016 MKC vehicles equipped with a 2.0L engine. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Consequence & remedy
Consequence: An electrical short circuit can increase the risk of a fire.
Remedy: Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed March 6, 2026. Additional letters will be sent once the final remedy is available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S01. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on January 16, 2026.
Jan 15, 2026
Ford Motor Company (Ford) is recalling certain 2016-2018 Focus, 2019 Explorer, and 2024 Explorer vehicles. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Consequence & remedy
Consequence: An electrical short circuit can increase the risk of a fire.
Remedy: Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded blanking plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed February 13, 2026. Additional letters will be sent once the final remedy is available, anticipated in October 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on January 16, 2026. This recall expands previous recall number 25V685.
Dec 22, 2023
Ford Motor Company (Ford) is recalling certain 2016-2018 Ford Focus and 2018-2022 Ford EcoSport vehicles. The oil pump drive belt or drive belt tensioner may fail, resulting in a loss of engine oil pressure.
Consequence & remedy
Consequence: A loss of oil pressure can result in an engine stall and a loss of power braking assist, increasing the risk of a crash.
Remedy: Dealers will replace the oil pump tensioner assembly and oil pump drive belt, free of charge. If engine failure occurs due to a damaged oil pump belt and/or oil pump belt tensioner, Ford has authorized dealers to replace the engine assembly as an interim repair before the availability of remedy parts for the final repair. This repair will be free of charge (parts and labor). Owner notification letters were mailed August 11, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S64.
Jul 5, 2019
Ford Motor Company (Ford) is recalling certain 2012 and 2017 Focus vehicles equipped with 2.0L GDI gasoline engines and 2013-2014 Focus ST vehicles equipped with 2.0L GTDI engines, previously recalled under 18V-735. The affected vehicles did not have the Powertrain Control Module (PCM) updated as intended. Therefore, the Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in the fuel vapor management system.
Consequence & remedy
Consequence: The excessive vacuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began July 29, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S22.
Additional source detail variants (2)
Fuel System, Gasoline:storage:evaporative Emissions:canister
Ford Motor Company (Ford) is recalling certain 2012 and 2017 Focus vehicles equipped with 2.0L GDI gasoline engines and 2013-2014 Focus ST vehicles equipped with 2.0L GTDI engines, previously recalled under 18V-735. The affected vehicles did not have the Powertrain Control Module (PCM) updated as intended. Therefore, the Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in the fuel vapor management system.
Consequence: The excessive vacuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began July 29, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S22.
Fuel System, Gasoline:storage
Ford Motor Company (Ford) is recalling certain 2012 and 2017 Focus vehicles equipped with 2.0L GDI gasoline engines and 2013-2014 Focus ST vehicles equipped with 2.0L GTDI engines, previously recalled under 18V-735. The affected vehicles did not have the Powertrain Control Module (PCM) updated as intended. Therefore, the Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in the fuel vapor management system.
Consequence: The excessive vacuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began July 29, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S22.
Nov 28, 2018
Ford Motor Company (Ford) is recalling certain 2016-2018 Ford Focus vehicles equipped with a 1.0L Fox GTDI engine and a 6-speed manual transmission. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.
Consequence & remedy
Consequence: A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.
Remedy: Ford will notify owners, and dealers will update vehicles with software that detects and prevents prolonged clutch slip, and will replace the clutch, as necessary, free of charge. The recall began January 17, 2019. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 18S07. Note: This recall is an expansion of Recall 18V-169.
Oct 22, 2018
Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
Consequence & remedy
Consequence: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Additional source detail variants (2)
Fuel System, Gasoline:storage:evaporative Emissions:canister
Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
Consequence: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Fuel System, Gasoline:storage
Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
Consequence: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Aug 28, 2017
Ford Motor Company (Ford) is recalling certain 2017 Focus vehicles. The rear left side seat back frame may have an insufficient weld between the outboard pivot bracket and the pivot nut joint, resulting in the seat back having reduced strength. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems," and 210, "Seat Belt Assembly Anchorages."
Consequence & remedy
Consequence: The reduced seat back strength may increase the risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will inspect and replace the rear second left side rear seat back as necessary, free of charge. The recall began October 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17C13.
Additional source detail variants (2)
Seats:mid/rear Assembly
Ford Motor Company (Ford) is recalling certain 2017 Focus vehicles. The rear left side seat back frame may have an insufficient weld between the outboard pivot bracket and the pivot nut joint, resulting in the seat back having reduced strength. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems," and 210, "Seat Belt Assembly Anchorages."
Consequence: The reduced seat back strength may increase the risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will inspect and replace the rear second left side rear seat back as necessary, free of charge. The recall began October 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17C13.
Seat Belts:rear/other
Ford Motor Company (Ford) is recalling certain 2017 Focus vehicles. The rear left side seat back frame may have an insufficient weld between the outboard pivot bracket and the pivot nut joint, resulting in the seat back having reduced strength. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems," and 210, "Seat Belt Assembly Anchorages."
Consequence: The reduced seat back strength may increase the risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will inspect and replace the rear second left side rear seat back as necessary, free of charge. The recall began October 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17C13.
Sep 28, 2016
Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
Consequence & remedy
Consequence: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.
Additional source detail variants (2)
Latches/locks/linkages:hatchback/liftgate:lock
Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
Consequence: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.
Structure:body:hatchback/liftgate
Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
Consequence: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
5EA26004 · Timing Belt Failure
Opened Jul 31, 2026 · No close date supplied
Status: open (inferred from source dates) · Engine; Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE25020 · Timing Belt Failure
Opened Dec 18, 2025 · Closed Jul 31, 2026
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE23015 · Oil Pump Failure
Opened Sep 20, 2023 · Closed Feb 14, 2024
Status: closed (inferred from source dates) · Engine And Engine Cooling:engine:oil/lubrication:pump
On September 20, 2023, the Office of Defects Investigation (ODI) opened PE23-015 to investigate instances of engine failure due to loss of oil pressure in model year (MY) 2018-2021 Ford EcoSport vehicles. Some consumers reported a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle was in motion. The investigation revealed that the engine oil pump drive belt tensioner arm may fracture, separate from the tensioner backing plate, and/or the oil pump drive belt may degrade and lose teeth, resulting in a loss of engine oil pressure. A loss of engine oil pressure can result in engine seizure, which can result in a loss of motive power and a loss of mechanical vacuum pump required to provide power braking assist, increase the risk of a crash. On December 22, 2023, Ford filed recall 23V-905 for certain MY 2016-2018 Ford Focus and 2018-2022 Ford EcoSport vehicles. The recall remedy provides the replacement of the oil pump drive belt tensioner assembly and oil pump drive belt with redesigned parts to improve robustness. In view of the recall action being taken by Ford, ODI is closing this Preliminary Evaluation. The agency reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
RQ23006 · Loss Of Motive Power
Opened Sep 15, 2023 · Closed Dec 20, 2024
Status: closed (inferred from source dates) · Fuel System, Gasoline:storage:evaporative Emissions:canister
On September 15, 2023, the Office of Defect Investigation (ODI) opened this Recall Query (RQ) after receiving 98 consumer complaints alleging loss of motive power in model year (MY) 2012-2018 Ford Focus vehicles. The RQ focused on the effectiveness of the remedies of Recall 18V-735 and 19V-515. In October 2018, Ford issued Recall 18V-735, which updated Powertrain Control Module (PCM) software in MY 2012-2018 Ford Focus vehicles equipped with 2.0L GDI engines built prior to April 13, 2017, and those with 2.0L GTDI engines built prior to February 2, 2018. The recall addressed vehicles experiencing a malfunctioning Canister Purge Valve (CPV) that can stick open and PCM software that does not adequately detect a stuck-open CPV condition. A CPV that is stuck open can cause excessive vacuum in the fuel vapor management system, potentially deforming the fuel tank, collapsing on itself. This deformation of the fuel tank can cause a Malfunction Indicator Light (MIL) to illuminate, an inaccurate or erratic fuel gauge indication, drivability issues, and/or loss of motive power. In July 2019, Ford issued Recall 19V-515, which addressed certain MY 2012 and MY 2017 Ford Focus vehicles equipped with 2.0L GDI and MY 2013-2014 Ford Focus vehicles equipped with 2.0L GTDI engines whose PCM software had been reprogrammed as a part of recall 18V-735. The updated software calibrations for these subject vehicles were not properly installed by Ford at the time of production. Approximately one year after this RQ was opened, on September 25, 2024, Ford initiated a customer satisfaction program (24N07) for MY 2012-2018 Ford Focus vehicles equipped with the 2.0L GDI and GTDI engines to—as ODI learned during this investigation—address a different issue with the CPV from the primary focus of the safety recalls (18V-735 and 19V-515). Ford stated the CPV may not operate as intended in these vehicles. A failed CPV on its own merit, may cause drivability concerns such as engine hesitation, running rough, or stalling at low speed, which will be accompanied by an illuminated MIL. This program provides a one-time replacement of the CPV for vehicles with 15 years of service or less (with no mileage restriction). This coverage will automatically transfer to subsequent owners. It is to be noted that the customer satisfaction program being taken by Ford to address this RQ investigation results in a much different and significantly less severe problem than the safety action taken to remedy 18V-735 and 19V-515. ODI found no further issues with the combined scope and severity related to 18V-735 and 19V-515 therefore, ODI is closing this Recall Query. The agency reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
Illustration