IllustrationWhile driving on the highway, (I-40) my dash lit up with "transmission fault stop car" The it shudders, bounced in and out of gear to finally completely stopped. Although I wasn't killed, my life was in danger. I believe the 2017 dual clutch transmission is faulty and should be added to the 2016 recall.
2017 Ford Focus
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2017 Ford Focus do not stand out strongly from the model-year median of 864.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Focus years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1220–25K
10725–50K
13550–75K
9475–100K
58100–150K
10150K+
526 reports with mileage · 370 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 452 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 229 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Fuel/propulsion System. Review the 116 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
18 crash reports2 fire reports12 injury reports
Power Train complaints
452 reportsDriving down the road the car shimmed a couple times I parked it turned it off when I went to turn it back on. It wouldn’t turn over when I finally got it to turn on. It wouldn’t go on reverse sometimes it’ll start sometimes it won’t sometimes it’ll go in reverse and sometimes it won’t.
My 2017 Ford Focus transmission failed at 113,000 miles. I was stranded in the middle of nowhere with a flashing warning light and no cell signal.
I have 2017 Ford Focus that is experiencing transmission issues related to the DPS6 Powershift transmission and TCM recall but my VIN number is [XXX] was not included. I am experiencing issues with the car shifting into 1st and 2nd gears, it will revv up at a stop but not accelerate immediately. I have been to a mechanic multip…
Read full complaint
I have 2017 Ford Focus that is experiencing transmission issues related to the DPS6 Powershift transmission and TCM recall but my VIN number is [XXX] was not included. I am experiencing issues with the car shifting into 1st and 2nd gears, it will revv up at a stop but not accelerate immediately. I have been to a mechanic multiple times and had the lower actuator replaced, new radiator fan installed, clutches scrubbed, and TCM reprogrammed. Multiple mechanics have recommended replacing the transmission as a solution. I called my local ford dealership who denied to service my vehicle under any recall or warranty, I spoke with a manufacturer representative who also told me that Ford is unwilling to do anything for my vehicle. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The contact owns a 2017 Ford Focus. The contact stated that after the vehicle was stopped at a traffic light, the vehicle failed to accelerate as intended while depressing the accelerator pedal, and the transmission downshifted between first and third gear. An abnormal sound could be heard coming from the transmission. After dr…
Read full complaint
The contact owns a 2017 Ford Focus. The contact stated that after the vehicle was stopped at a traffic light, the vehicle failed to accelerate as intended while depressing the accelerator pedal, and the transmission downshifted between first and third gear. An abnormal sound could be heard coming from the transmission. After driving a short distance, the vehicle functioned as intended. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. The contact stated that the failure persisted. The contact stated that while driving at 40 MPH on a separate occasion, the transmission downshifted between third and fourth gear, and the vehicle went into limp mode. In addition, an abnormal sound could be heard coming from the transmission, and the vehicle jerked. The contact stated that upon starting the vehicle most recently, the vehicle made an abnormal sound. The check engine warning light illuminated. The vehicle was taken to AutoZone for a diagnostic test, and the contact was informed that the failure may be related to the transmission clutch. Additionally, the contact stated that the fan had turned on independently, and had failed to turn on while driving on other occasions, causing the vehicle to overheat. The vehicle was taken to a collision center, where the contact was informed that the transmission was failing. The cooling system was replaced; however, the failure persisted. The vehicle was taken back to the dealer, where it was diagnosed that an unknown sensor had failed, and the sensor was replaced. The contact stated that the transmission failure was worsening. The vehicle was not repaired. The manufacturer was not informed of the failure. The failure mileage was approximately 50,000.
Bought this car last June of this year and ever since then. First gear will buck sometime and second gear too. After I gotten to thrird gear it goes away. My local Tires Plus says that's with all Ford focus'es he think I'm crazy but I have let a friend drive it when I there and he says the same thing as me. It bucks..
Transmission is overheating is the warning I keep getting on the dashboard read out. The transmission is shifting very hard and you can hear it grinding and winding up when it is trying to shift. I had the car put on a computer at a shop and the codes were reading that the clutch was not releasing and he tried to reset it and it…
Read full complaint
Transmission is overheating is the warning I keep getting on the dashboard read out. The transmission is shifting very hard and you can hear it grinding and winding up when it is trying to shift. I had the car put on a computer at a shop and the codes were reading that the clutch was not releasing and he tried to reset it and it kept failing. I googled my car and saw that this is a known problem with them and that Ford hasn't acknowledged the problem yet.
Transmission actuator A and actuator B making the Transmission not able to shift. Happened after new battery installed and was told it could have been a surge sent to Transmission control module breaking the actuators.
The contact owns a 2017 Ford Focus. The contact stated that while stopped at a traffic light, the light changed, and the accelerator pedal was depressed; however, the vehicle hesitated and then jolted into gear. The contact stated that the failure was a recurring failure. The contact stated that the engine symbol was displayed, …
Read full complaint
The contact owns a 2017 Ford Focus. The contact stated that while stopped at a traffic light, the light changed, and the accelerator pedal was depressed; however, the vehicle hesitated and then jolted into gear. The contact stated that the failure was a recurring failure. The contact stated that the engine symbol was displayed, and the vehicle failed to respond while depressing the accelerator pedal. The contact stated that the RPM gauge was RED-lined. The contact stated that the vehicle failed to accelerate above 10 MPH. There was no warning light illuminated. The contact stated that at first, he was stopping the vehicle and turning off and restarting the vehicle to reset the transmission. The contact stated that turning off and restarting the vehicle no longer resets the transmission. The vehicle was taken to a local dealer, where it was diagnosed and determined that the transmission needed to be rebuilt. The vehicle was not repaired. The manufacturer was informed of the failure and referred the contact to the NHTSA Hotline. The failure mileage was 92,619.
The contact owns a 2017 Ford Focus. The contact stated that while stopped at the bank drive-thru line, the vehicle stalled. After several attempts, the vehicle restarted. The failure was progressively worsening. The vehicle was taken to a dealer, and the fuel pump, AX Sender, and pump assembly, AA gasket, B sensor, and fuel inj…
Read full complaint
The contact owns a 2017 Ford Focus. The contact stated that while stopped at the bank drive-thru line, the vehicle stalled. After several attempts, the vehicle restarted. The failure was progressively worsening. The vehicle was taken to a dealer, and the fuel pump, AX Sender, and pump assembly, AA gasket, B sensor, and fuel injector pressure parts were replaced. The contact stated that on another occasion, while driving in heavy traffic at 35 MPH, the vehicle stalled with several warning lights illuminated. The contact stated that several months ago, on a separate occasion, while driving at various speeds, the vehicle failed to accelerate as intended while depressing the accelerator pedal, and the vehicle stalled. The contact was able to coast to the side of the road. The vehicle failed to restart, and the contact waited for approximately an hour before the vehicle restarted. The vehicle was taken to several dealers to be repaired. While an employee from one of the dealers was test-driving the vehicle, the vehicle stalled. The vehicle was diagnosed, and it was determined that there were fuel vapors in the line, and that the high side sensor pressure dropped, and low side sensor pressure dropped. The vehicle was repaired. Most recently, the contact stated that the transmission had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure and advised the contact to file a claim. The failure mileage was approximately 30,000.
Official recalls
1026V369000 · Fuel System, Gasoline:storage:evaporative Emissions:canister
Jun 9, 2026
Ford Motor Company (Ford) is recalling certain 2012-2018 Focus vehicles previously repaired incorrectly under recall number 18V735. The Canister Purge Valve (CPV) may malfunction, causing the engine to stall unexpectedly while driving.
Consequence & remedy
Consequence: An engine that stalls while driving increases the risk of a crash.
Remedy: Dealers will update the powertrain control module (PCM) software, free of charge. Owner notification letters were mailed July 29, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S40. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6,2026.
26V376000 · Power Train:manual Transmission
Jun 9, 2026
Ford Motor Company (Ford) is recalling certain 2015-2018 Focus and 2013-2016 Fusion vehicles previously repaired incorrectly under recall numbers 18V169 and 18V845. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.
Consequence & remedy
Consequence: A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.
Remedy: Dealers will update the software, free of charge. Additionally, dealers will inspect Focus vehicles and replace the clutch assembly as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed August 5, 2026. Additional letters will be sent once the remedy is available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S43. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6,2026.
26V011000 · Equipment:electrical:engine Block Heater
Jan 15, 2026
Ford Motor Company (Ford) is recalling certain 2013-2018 Focus, 2013-2019 Escape, and 2015-2016 MKC vehicles equipped with a 2.0L engine. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Consequence & remedy
Consequence: An electrical short circuit can increase the risk of a fire.
Remedy: Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed March 6, 2026. Additional letters will be sent once the final remedy is available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S01. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on January 16, 2026.
26V012000 · Equipment:electrical:engine Block Heater
Jan 15, 2026
Ford Motor Company (Ford) is recalling certain 2016-2018 Focus, 2019 Explorer, and 2024 Explorer vehicles. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Consequence & remedy
Consequence: An electrical short circuit can increase the risk of a fire.
Remedy: Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded blanking plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed February 13, 2026. Additional letters will be sent once the final remedy is available, anticipated in October 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on January 16, 2026. This recall expands previous recall number 25V685.
23V905000 · Engine And Engine Cooling:engine:oil/lubrication:pump
Dec 22, 2023
Ford Motor Company (Ford) is recalling certain 2016-2018 Ford Focus and 2018-2022 Ford EcoSport vehicles. The oil pump drive belt or drive belt tensioner may fail, resulting in a loss of engine oil pressure.
Consequence & remedy
Consequence: A loss of oil pressure can result in an engine stall and a loss of power braking assist, increasing the risk of a crash.
Remedy: Dealers will replace the oil pump tensioner assembly and oil pump drive belt, free of charge. If engine failure occurs due to a damaged oil pump belt and/or oil pump belt tensioner, Ford has authorized dealers to replace the engine assembly as an interim repair before the availability of remedy parts for the final repair. This repair will be free of charge (parts and labor). Owner notification letters were mailed August 11, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S64.
19V515000 · Fuel System, Gasoline:storage; Fuel System, Gasoline:storage:evaporative Emissions:canister
Jul 5, 2019
Ford Motor Company (Ford) is recalling certain 2012 and 2017 Focus vehicles equipped with 2.0L GDI gasoline engines and 2013-2014 Focus ST vehicles equipped with 2.0L GTDI engines, previously recalled under 18V-735. The affected vehicles did not have the Powertrain Control Module (PCM) updated as intended. Therefore, the Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in the fuel vapor management system.
Consequence & remedy
Consequence: The excessive vacuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began July 29, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S22.
Additional source detail variants (2)
Fuel System, Gasoline:storage:evaporative Emissions:canister
Ford Motor Company (Ford) is recalling certain 2012 and 2017 Focus vehicles equipped with 2.0L GDI gasoline engines and 2013-2014 Focus ST vehicles equipped with 2.0L GTDI engines, previously recalled under 18V-735. The affected vehicles did not have the Powertrain Control Module (PCM) updated as intended. Therefore, the Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in the fuel vapor management system.
Consequence: The excessive vacuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began July 29, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S22.
Fuel System, Gasoline:storage
Ford Motor Company (Ford) is recalling certain 2012 and 2017 Focus vehicles equipped with 2.0L GDI gasoline engines and 2013-2014 Focus ST vehicles equipped with 2.0L GTDI engines, previously recalled under 18V-735. The affected vehicles did not have the Powertrain Control Module (PCM) updated as intended. Therefore, the Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in the fuel vapor management system.
Consequence: The excessive vacuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began July 29, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S22.
18V845000 · Power Train:manual Transmission
Nov 28, 2018
Ford Motor Company (Ford) is recalling certain 2016-2018 Ford Focus vehicles equipped with a 1.0L Fox GTDI engine and a 6-speed manual transmission. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.
Consequence & remedy
Consequence: A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.
Remedy: Ford will notify owners, and dealers will update vehicles with software that detects and prevents prolonged clutch slip, and will replace the clutch, as necessary, free of charge. The recall began January 17, 2019. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 18S07. Note: This recall is an expansion of Recall 18V-169.
18V735000 · Fuel System, Gasoline:storage; Fuel System, Gasoline:storage:evaporative Emissions:canister
Oct 22, 2018
Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
Consequence & remedy
Consequence: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Additional source detail variants (2)
Fuel System, Gasoline:storage:evaporative Emissions:canister
Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
Consequence: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Fuel System, Gasoline:storage
Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
Consequence: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
17V528000 · Seat Belts:rear/other; Seats:mid/rear Assembly
Aug 28, 2017
Ford Motor Company (Ford) is recalling certain 2017 Focus vehicles. The rear left side seat back frame may have an insufficient weld between the outboard pivot bracket and the pivot nut joint, resulting in the seat back having reduced strength. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems," and 210, "Seat Belt Assembly Anchorages."
Consequence & remedy
Consequence: The reduced seat back strength may increase the risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will inspect and replace the rear second left side rear seat back as necessary, free of charge. The recall began October 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17C13.
Additional source detail variants (2)
Seats:mid/rear Assembly
Ford Motor Company (Ford) is recalling certain 2017 Focus vehicles. The rear left side seat back frame may have an insufficient weld between the outboard pivot bracket and the pivot nut joint, resulting in the seat back having reduced strength. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems," and 210, "Seat Belt Assembly Anchorages."
Consequence: The reduced seat back strength may increase the risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will inspect and replace the rear second left side rear seat back as necessary, free of charge. The recall began October 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17C13.
Seat Belts:rear/other
Ford Motor Company (Ford) is recalling certain 2017 Focus vehicles. The rear left side seat back frame may have an insufficient weld between the outboard pivot bracket and the pivot nut joint, resulting in the seat back having reduced strength. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems," and 210, "Seat Belt Assembly Anchorages."
Consequence: The reduced seat back strength may increase the risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will inspect and replace the rear second left side rear seat back as necessary, free of charge. The recall began October 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17C13.
16V698000 · Latches/locks/linkages:hatchback/liftgate:lock; Structure:body:hatchback/liftgate
Sep 28, 2016
Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
Consequence & remedy
Consequence: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.
Additional source detail variants (2)
Latches/locks/linkages:hatchback/liftgate:lock
Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
Consequence: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.
Structure:body:hatchback/liftgate
Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
Consequence: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
5EA26004 · Timing Belt Failure
Opened Jul 31, 2026 · No close date supplied
Status: open (inferred from source dates) · Engine; Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE25020 · Timing Belt Failure
Opened Dec 18, 2025 · Closed Jul 31, 2026
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE23015 · Oil Pump Failure
Opened Sep 20, 2023 · Closed Feb 14, 2024
Status: closed (inferred from source dates) · Engine And Engine Cooling:engine:oil/lubrication:pump
On September 20, 2023, the Office of Defects Investigation (ODI) opened PE23-015 to investigate instances of engine failure due to loss of oil pressure in model year (MY) 2018-2021 Ford EcoSport vehicles. Some consumers reported a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle was in motion. The investigation revealed that the engine oil pump drive belt tensioner arm may fracture, separate from the tensioner backing plate, and/or the oil pump drive belt may degrade and lose teeth, resulting in a loss of engine oil pressure. A loss of engine oil pressure can result in engine seizure, which can result in a loss of motive power and a loss of mechanical vacuum pump required to provide power braking assist, increase the risk of a crash. On December 22, 2023, Ford filed recall 23V-905 for certain MY 2016-2018 Ford Focus and 2018-2022 Ford EcoSport vehicles. The recall remedy provides the replacement of the oil pump drive belt tensioner assembly and oil pump drive belt with redesigned parts to improve robustness. In view of the recall action being taken by Ford, ODI is closing this Preliminary Evaluation. The agency reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
RQ23006 · Loss Of Motive Power
Opened Sep 15, 2023 · Closed Dec 20, 2024
Status: closed (inferred from source dates) · Fuel System, Gasoline:storage:evaporative Emissions:canister
On September 15, 2023, the Office of Defect Investigation (ODI) opened this Recall Query (RQ) after receiving 98 consumer complaints alleging loss of motive power in model year (MY) 2012-2018 Ford Focus vehicles. The RQ focused on the effectiveness of the remedies of Recall 18V-735 and 19V-515. In October 2018, Ford issued Recall 18V-735, which updated Powertrain Control Module (PCM) software in MY 2012-2018 Ford Focus vehicles equipped with 2.0L GDI engines built prior to April 13, 2017, and those with 2.0L GTDI engines built prior to February 2, 2018. The recall addressed vehicles experiencing a malfunctioning Canister Purge Valve (CPV) that can stick open and PCM software that does not adequately detect a stuck-open CPV condition. A CPV that is stuck open can cause excessive vacuum in the fuel vapor management system, potentially deforming the fuel tank, collapsing on itself. This deformation of the fuel tank can cause a Malfunction Indicator Light (MIL) to illuminate, an inaccurate or erratic fuel gauge indication, drivability issues, and/or loss of motive power. In July 2019, Ford issued Recall 19V-515, which addressed certain MY 2012 and MY 2017 Ford Focus vehicles equipped with 2.0L GDI and MY 2013-2014 Ford Focus vehicles equipped with 2.0L GTDI engines whose PCM software had been reprogrammed as a part of recall 18V-735. The updated software calibrations for these subject vehicles were not properly installed by Ford at the time of production. Approximately one year after this RQ was opened, on September 25, 2024, Ford initiated a customer satisfaction program (24N07) for MY 2012-2018 Ford Focus vehicles equipped with the 2.0L GDI and GTDI engines to—as ODI learned during this investigation—address a different issue with the CPV from the primary focus of the safety recalls (18V-735 and 19V-515). Ford stated the CPV may not operate as intended in these vehicles. A failed CPV on its own merit, may cause drivability concerns such as engine hesitation, running rough, or stalling at low speed, which will be accompanied by an illuminated MIL. This program provides a one-time replacement of the CPV for vehicles with 15 years of service or less (with no mileage restriction). This coverage will automatically transfer to subsequent owners. It is to be noted that the customer satisfaction program being taken by Ford to address this RQ investigation results in a much different and significantly less severe problem than the safety action taken to remedy 18V-735 and 19V-515. ODI found no further issues with the combined scope and severity related to 18V-735 and 19V-515 therefore, ODI is closing this Recall Query. The agency reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.