NHTSA owner reports · September 18, 2026 snapshot.
Fuel System, Gasoline complaints
61 reportsClear category filter110,000 miles · Mar 18, 2024
Fuel System, Gasoline
The contact owns a 2016 Ford Focus. The contact stated that while driving at an undisclosed speed, the vehicle began to jerk and hesitate, after which the vehicle lost significant motive power and was unable to accelerate above 60 MPH. No warning lights were illuminated. The vehicle was taken to the dealer, who diagnosed a failu…
Read full complaint
The contact owns a 2016 Ford Focus. The contact stated that while driving at an undisclosed speed, the vehicle began to jerk and hesitate, after which the vehicle lost significant motive power and was unable to accelerate above 60 MPH. No warning lights were illuminated. The vehicle was taken to the dealer, who diagnosed a failure with the fuel sensor. The vehicle was repaired, but the failure reoccurred. The vehicle was taken back to the dealer, who was unable to diagnose the failure. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline) but the VIN was not included. The manufacturer was notified of the failure but referred the contact to the NHTSA Hotline for assistance. The failure mileage was 110,000.
NHTSA ODI #11578077
160,000 miles · Mar 6, 2024
Fuel System, Gasoline
The contact’s son owns a 2016 Ford Focus. The contact stated that while refueling the vehicle at the gas station, the contact had to wait for approximately 2-30 minutes before the vehicle would start-up. The contact stated that while the vehicle was parked, the RPM revved and fluctuated from high to low. The contact also stated …
Read full complaint
The contact’s son owns a 2016 Ford Focus. The contact stated that while refueling the vehicle at the gas station, the contact had to wait for approximately 2-30 minutes before the vehicle would start-up. The contact stated that while the vehicle was parked, the RPM revved and fluctuated from high to low. The contact also stated that while driving from a stop light, the vehicle stalled. The check engine warning light was illuminated. The vehicle was taken to the dealer where it was diagnosed with a failed canister purge valve. The vehicle was not repaired due the cost. The manufacturer was notified of the failure and stated a previous recall was cleared due to the vehicle passing the canister purge valve test and the power train control module was updated. The failure mileage was approximately 160,000.
NHTSA ODI #11575786
Mileage unknown · Nov 22, 2023
Fuel System, Gasoline
The contact owns a 2016 Ford Focus. The contact stated that after starting the vehicle, he observed that the vehicle was idling abnormally rough. While driving at an undisclosed speed, the vehicle lost motive power and seemed to hesitate while shifting between gears. The check engine warning light was illuminated. The vehicle wa…
Read full complaint
The contact owns a 2016 Ford Focus. The contact stated that after starting the vehicle, he observed that the vehicle was idling abnormally rough. While driving at an undisclosed speed, the vehicle lost motive power and seemed to hesitate while shifting between gears. The check engine warning light was illuminated. The vehicle was taken to the dealer, who determined that the canister purge valve was stuck in the open position. The vehicle was repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline). The manufacturer was notified of the failure but provided no assistance. The failure mileage was unknown.
NHTSA ODI #11556423
113,000 miles · Nov 3, 2023
Fuel System, Gasoline
The contact owns a 2016 Ford Focus. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to an independent mechanic, who determined that the fuel tank was deformed due to a stuck canister purge valve. The vehicle was not repaired. After investigating the…
Read full complaint
The contact owns a 2016 Ford Focus. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to an independent mechanic, who determined that the fuel tank was deformed due to a stuck canister purge valve. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline); the VIN was included, and the repair was already completed. The manufacturer was notified of the failure, and a case was opened. The failure mileage was 113,000.
NHTSA ODI #11553490
Mileage unknown · Sep 22, 2023
Fuel System, Gasoline
The contact owns a 2016 Ford Focus. The contact stated that the vehicle failed to immediately start up after refueling. There was no warning light illuminated. The contact also stated that the vehicle stalled without warning while driving at various speeds. Upon investigation, the contact discovered NHTSA Campaign Number: 18V735…
Read full complaint
The contact owns a 2016 Ford Focus. The contact stated that the vehicle failed to immediately start up after refueling. There was no warning light illuminated. The contact also stated that the vehicle stalled without warning while driving at various speeds. Upon investigation, the contact discovered NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline). The dealer was notified of the failure and an appointment was scheduled to have the vehicle serviced. The contact was later informed by the dealer that the vehicle was not included in the recall. The manufacturer was notified of the failure, and the contact was provided a case number. The vehicle was not repaired. The failure mileage was unknown.
NHTSA ODI #11545971
107,000 miles · Sep 19, 2023
Fuel System, Gasoline
The contact owns a 2016 Ford Focus. The contact stated while driving 40 MPH, the check engine warning light illuminated. The vehicle was taken to an independent mechanic, who determined there was an excessive vacuum in the fuel system. The vehicle was not repaired. After investigating the failure, the contact related it to NHTSA…
Read full complaint
The contact owns a 2016 Ford Focus. The contact stated while driving 40 MPH, the check engine warning light illuminated. The vehicle was taken to an independent mechanic, who determined there was an excessive vacuum in the fuel system. The vehicle was not repaired. After investigating the failure, the contact related it to NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline) but the VIN was not included. The manufacturer was notified of the failure but referred the contact to the NHTSA Hotline for assistance. The failure mileage was 107,000.
NHTSA ODI #11545500
51,000 miles · Aug 22, 2023
Fuel System, Gasoline
The contact owns a 2016 Ford Focus. The contact stated while driving 65 MPH, the vehicle suddenly began to surge and shake erratically. The contact was able to exit the main roadway, after which the vehicle stalled and failed to restart. The check engine warning light was illuminated. The vehicle was towed to an independent mech…
Read full complaint
The contact owns a 2016 Ford Focus. The contact stated while driving 65 MPH, the vehicle suddenly began to surge and shake erratically. The contact was able to exit the main roadway, after which the vehicle stalled and failed to restart. The check engine warning light was illuminated. The vehicle was towed to an independent mechanic, who diagnosed a failure with the canister purge valve. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline), but the VIN was not included. The manufacturer was not notified of the failure. The failure mileage was 51,000.
NHTSA ODI #11540155
100,000 miles · May 9, 2023
EngineFuel System, Gasoline
The contact owns a 2016 Ford Focus. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The contact used a portable scanner and retrieved DTC codes regarding the fuel rail pressure - Low. The contact’s husband replaced the canister purge valve (CPV); however, the contact sta…
Read full complaint
The contact owns a 2016 Ford Focus. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The contact used a portable scanner and retrieved DTC codes regarding the fuel rail pressure - Low. The contact’s husband replaced the canister purge valve (CPV); however, the contact stated that the failure reoccurred, and the vehicle was jerking, and losing motive power, and hesitating to restart. The vehicle was diagnosed again, and the contact retrieved fault codes for the fuel rail system again. The vehicle was then taken to a local dealer, where it was diagnosed that the fuel pump needed to be replaced. The contact's husband completed the repair; however, the contact stated that after refueling and driving at an undisclosed speed, the low fuel warning light illuminated. The contact referenced the failures to NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline); however, the VIN was not included in the recall. The manufacturer was made aware of the failure and advised the contact to file a complaint with the NHTSA Hotline. The failure mileage was 100,000.
NHTSA ODI #11521247
79,000 miles · Apr 24, 2023
EngineFuel System, Gasoline
The contact owns a 2016 Ford Focus. The contact stated while driving at various speeds, the vehicle lost motive power and stalled. Additionally, the vehicle stalled occasionally after refueling. The check engine warning light was illuminated. The contact was able to restart the vehicle occasionally after several attempts. The ve…
Read full complaint
The contact owns a 2016 Ford Focus. The contact stated while driving at various speeds, the vehicle lost motive power and stalled. Additionally, the vehicle stalled occasionally after refueling. The check engine warning light was illuminated. The contact was able to restart the vehicle occasionally after several attempts. The vehicle was taken to an independent mechanic to be diagnosed. The contact was informed that the canister purge valve remained open causing the failure. The contact stated that the failure was related to NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline); however, the VIN was not included. The vehicle was not repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 79,000.
NHTSA ODI #11518625
86,000 miles · Mar 23, 2023
Fuel System, GasolinePower Train
The contact owns a 2016 Ford Focus. The contact stated that he noticed that the vehicle was experiencing excessive fuel consumption. The contact stated that after fueling the vehicle, the vehicle consumed three quarts of fuel within 20-30 miles. The vehicle was taken to the dealer, where it was diagnosed that the Canister Purge …
Read full complaint
The contact owns a 2016 Ford Focus. The contact stated that he noticed that the vehicle was experiencing excessive fuel consumption. The contact stated that after fueling the vehicle, the vehicle consumed three quarts of fuel within 20-30 miles. The vehicle was taken to the dealer, where it was diagnosed that the Canister Purge Valve (CPV) was malfunctioning, causing an excessive vacuum in fuel vapor management system. The dealer informed the contact that the vehicle could not be repaired under NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline) as the VIN was not included. The canister purge valve was replaced at the contact's expense. Additionally, the contact stated while reversing out of the driveway, the check engine warning light was illuminated. The contact stated that upon attempting to reverse out of the driveway on another occasion, the gear shifter was moved into reverse (R), but the vehicle failed to respond. The contact shifted into neutral (N) and pushed the vehicle out of the driveway. The contact was able to drive the vehicle, however, the message "Car Overheating. Stop Safely" was displayed. The vehicle was taken to an independent mechanic, where it was diagnosed that the transmission clutch was defective. The contact related the failure to NHTSA Campaign Number: 18V845000 (Power Train). The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 86,000.
NHTSA ODI #11513398
Official recalls
10Jun 9, 2026
Ford Motor Company (Ford) is recalling certain 2012-2018 Focus vehicles previously repaired incorrectly under recall number 18V735. The Canister Purge Valve (CPV) may malfunction, causing the engine to stall unexpectedly while driving.
Consequence & remedy
Consequence: An engine that stalls while driving increases the risk of a crash.
Remedy: Dealers will update the powertrain control module (PCM) software, free of charge. Owner notification letters were mailed July 29, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S40. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6,2026.
Jun 9, 2026
Ford Motor Company (Ford) is recalling certain 2015-2018 Focus and 2013-2016 Fusion vehicles previously repaired incorrectly under recall numbers 18V169 and 18V845. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.
Consequence & remedy
Consequence: A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.
Remedy: Dealers will update the software, free of charge. Additionally, dealers will inspect Focus vehicles and replace the clutch assembly as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed August 5, 2026. Additional letters will be sent once the remedy is available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S43. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6,2026.
Jan 15, 2026
Ford Motor Company (Ford) is recalling certain 2013-2018 Focus, 2013-2019 Escape, and 2015-2016 MKC vehicles equipped with a 2.0L engine. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Consequence & remedy
Consequence: An electrical short circuit can increase the risk of a fire.
Remedy: Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed March 6, 2026. Additional letters will be sent once the final remedy is available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S01. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on January 16, 2026.
Jan 15, 2026
Ford Motor Company (Ford) is recalling certain 2016-2018 Focus, 2019 Explorer, and 2024 Explorer vehicles. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Consequence & remedy
Consequence: An electrical short circuit can increase the risk of a fire.
Remedy: Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded blanking plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed February 13, 2026. Additional letters will be sent once the final remedy is available, anticipated in October 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on January 16, 2026. This recall expands previous recall number 25V685.
Dec 22, 2023
Ford Motor Company (Ford) is recalling certain 2016-2018 Ford Focus and 2018-2022 Ford EcoSport vehicles. The oil pump drive belt or drive belt tensioner may fail, resulting in a loss of engine oil pressure.
Consequence & remedy
Consequence: A loss of oil pressure can result in an engine stall and a loss of power braking assist, increasing the risk of a crash.
Remedy: Dealers will replace the oil pump tensioner assembly and oil pump drive belt, free of charge. If engine failure occurs due to a damaged oil pump belt and/or oil pump belt tensioner, Ford has authorized dealers to replace the engine assembly as an interim repair before the availability of remedy parts for the final repair. This repair will be free of charge (parts and labor). Owner notification letters were mailed August 11, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S64.
Nov 28, 2018
Ford Motor Company (Ford) is recalling certain 2016-2018 Ford Focus vehicles equipped with a 1.0L Fox GTDI engine and a 6-speed manual transmission. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.
Consequence & remedy
Consequence: A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.
Remedy: Ford will notify owners, and dealers will update vehicles with software that detects and prevents prolonged clutch slip, and will replace the clutch, as necessary, free of charge. The recall began January 17, 2019. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 18S07. Note: This recall is an expansion of Recall 18V-169.
Oct 22, 2018
Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
Consequence & remedy
Consequence: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Additional source detail variants (2)
Fuel System, Gasoline:storage:evaporative Emissions:canister
Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
Consequence: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Fuel System, Gasoline:storage
Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
Consequence: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Mar 12, 2018
Ford Motor Company (Ford) is recalling certain 2013-2014 Ford Fusion vehicles equipped with a 1.6L GTDI engine and 6-speed manual transmission and 2015-2016 Ford Focus vehicles equipped with a 1.0L GTDI engine and 6-speed manual transmission. Also included are four 2017 Ford Focus vehicles that had clutch replacements with potentially affected parts. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.
Consequence & remedy
Consequence: A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.
Remedy: Ford will notify owners, and dealers will update the Focus vehicles with software that detects and prevents prolonged clutch slip, and will replace the clutch, as necessary, free of charge. Owners of Fusion vehicles will have their clutch assembly replaced free of charge. The recall began August 3, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S07.
Jan 24, 2017
Ford Motor Company (Ford) is recalling certain 2016 Focus and C-Max vehicles. The floor pan may have improperly welded left-hand apron joints.
Consequence & remedy
Consequence: Improperly welded apron joints may reduce the front-end structural integrity of the vehicle, increasing the risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will inspect the apron joints, repairing the vehicle, as necessary, free of charge. The recall began March 8, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17S03.
Sep 28, 2016
Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
Consequence & remedy
Consequence: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.
Additional source detail variants (2)
Latches/locks/linkages:hatchback/liftgate:lock
Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
Consequence: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.
Structure:body:hatchback/liftgate
Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
Consequence: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4EA26004 · Timing Belt Failure
Opened Jul 31, 2026 · No close date supplied
Status: open (inferred from source dates) · Engine; Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE25020 · Timing Belt Failure
Opened Dec 18, 2025 · Closed Jul 31, 2026
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE23015 · Oil Pump Failure
Opened Sep 20, 2023 · Closed Feb 14, 2024
Status: closed (inferred from source dates) · Engine And Engine Cooling:engine:oil/lubrication:pump
On September 20, 2023, the Office of Defects Investigation (ODI) opened PE23-015 to investigate instances of engine failure due to loss of oil pressure in model year (MY) 2018-2021 Ford EcoSport vehicles. Some consumers reported a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle was in motion. The investigation revealed that the engine oil pump drive belt tensioner arm may fracture, separate from the tensioner backing plate, and/or the oil pump drive belt may degrade and lose teeth, resulting in a loss of engine oil pressure. A loss of engine oil pressure can result in engine seizure, which can result in a loss of motive power and a loss of mechanical vacuum pump required to provide power braking assist, increase the risk of a crash. On December 22, 2023, Ford filed recall 23V-905 for certain MY 2016-2018 Ford Focus and 2018-2022 Ford EcoSport vehicles. The recall remedy provides the replacement of the oil pump drive belt tensioner assembly and oil pump drive belt with redesigned parts to improve robustness. In view of the recall action being taken by Ford, ODI is closing this Preliminary Evaluation. The agency reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
RQ23006 · Loss Of Motive Power
Opened Sep 15, 2023 · Closed Dec 20, 2024
Status: closed (inferred from source dates) · Fuel System, Gasoline:storage:evaporative Emissions:canister
On September 15, 2023, the Office of Defect Investigation (ODI) opened this Recall Query (RQ) after receiving 98 consumer complaints alleging loss of motive power in model year (MY) 2012-2018 Ford Focus vehicles. The RQ focused on the effectiveness of the remedies of Recall 18V-735 and 19V-515. In October 2018, Ford issued Recall 18V-735, which updated Powertrain Control Module (PCM) software in MY 2012-2018 Ford Focus vehicles equipped with 2.0L GDI engines built prior to April 13, 2017, and those with 2.0L GTDI engines built prior to February 2, 2018. The recall addressed vehicles experiencing a malfunctioning Canister Purge Valve (CPV) that can stick open and PCM software that does not adequately detect a stuck-open CPV condition. A CPV that is stuck open can cause excessive vacuum in the fuel vapor management system, potentially deforming the fuel tank, collapsing on itself. This deformation of the fuel tank can cause a Malfunction Indicator Light (MIL) to illuminate, an inaccurate or erratic fuel gauge indication, drivability issues, and/or loss of motive power. In July 2019, Ford issued Recall 19V-515, which addressed certain MY 2012 and MY 2017 Ford Focus vehicles equipped with 2.0L GDI and MY 2013-2014 Ford Focus vehicles equipped with 2.0L GTDI engines whose PCM software had been reprogrammed as a part of recall 18V-735. The updated software calibrations for these subject vehicles were not properly installed by Ford at the time of production. Approximately one year after this RQ was opened, on September 25, 2024, Ford initiated a customer satisfaction program (24N07) for MY 2012-2018 Ford Focus vehicles equipped with the 2.0L GDI and GTDI engines to—as ODI learned during this investigation—address a different issue with the CPV from the primary focus of the safety recalls (18V-735 and 19V-515). Ford stated the CPV may not operate as intended in these vehicles. A failed CPV on its own merit, may cause drivability concerns such as engine hesitation, running rough, or stalling at low speed, which will be accompanied by an illuminated MIL. This program provides a one-time replacement of the CPV for vehicles with 15 years of service or less (with no mileage restriction). This coverage will automatically transfer to subsequent owners. It is to be noted that the customer satisfaction program being taken by Ford to address this RQ investigation results in a much different and significantly less severe problem than the safety action taken to remedy 18V-735 and 19V-515. ODI found no further issues with the combined scope and severity related to 18V-735 and 19V-515 therefore, ODI is closing this Recall Query. The agency reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Illustration