NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
245 reports60,000 miles · Aug 13, 2026
Back Over Prevention
The contact owns a 2019 Ford Flex. The contact stated that while reversing at an undisclosed speed, the rear-view camera was distorted and flipped upside down. No warning lights were illuminated. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repai…
Read full complaint
The contact owns a 2019 Ford Flex. The contact stated that while reversing at an undisclosed speed, the rear-view camera was distorted and flipped upside down. No warning lights were illuminated. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The local dealer was contacted and confirmed that the part was not yet available. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not notified of the failure. The failure mileage was approximately 60,000.
NHTSA ODI #11756735
35,000 miles · Aug 7, 2026
Back Over PreventionSeat BeltsStructure
The contact owns a 2019 Ford Flex. The contact stated that while reversing, the rear-view camera went blank and flashed on and off. The contact stated that while attempting to latch the front driver's seat belt, the seat belt failed to retract as intended. The contact stated that the seat belt was stuck. The vehicle was not diag…
Read full complaint
The contact owns a 2019 Ford Flex. The contact stated that while reversing, the rear-view camera went blank and flashed on and off. The contact stated that while attempting to latch the front driver's seat belt, the seat belt failed to retract as intended. The contact stated that the seat belt was stuck. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact received notifications of NHTSA Campaign Numbers: 25V829000 (Structure) and 24V951000 (Back Over Prevention); however, the parts to do the recall repairs were unavailable. The contact stated that the failure was a persistent failure. The contact stated that the rear-view camera failure was an inconvenience and a hazard due to a disability. The contact stated that turning the neck was painful while reversing. The manufacturer was made aware of the failure but provided no assistance. The failure mileage was approximately 35,000.
NHTSA ODI #11755447
90,000 miles · Aug 4, 2026
Back Over Prevention
The contact owns a 2019 Ford Flex. The contact stated that the rear-view camera unexpectedly turned off while reversing. The contact stated that it was difficult to reverse while the back over prevention camera was inoperable. There was no warning light illuminated. The contact received notification of NHTSA Campaign Number: 25…
Read full complaint
The contact owns a 2019 Ford Flex. The contact stated that the rear-view camera unexpectedly turned off while reversing. The contact stated that it was difficult to reverse while the back over prevention camera was inoperable. There was no warning light illuminated. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention). The local dealer was contacted and confirmed that the part to do the recall repair was not yet available. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 90,000.
NHTSA ODI #11754666
Mileage unknown · Aug 3, 2026
Unknown Or Other
My 2019 Ford Flex is experiencing a complete factory rearview backup camera failure. When I place the vehicle into reverse, the center display screen regularly goes completely blank/black or blue or severe image distortion or black with warning "camera is unavailable". This is now happening almost every time I drive the vehicl…
Read full complaint
My 2019 Ford Flex is experiencing a complete factory rearview backup camera failure. When I place the vehicle into reverse, the center display screen regularly goes completely blank/black or blue or severe image distortion or black with warning "camera is unavailable". This is now happening almost every time I drive the vehicle and started about eight months ago but is now getting more frequent. This failure eliminates my rearward line of sight, creating an immediate back-over crash risk and a severe pedestrian safety hazard. This vehicle is part of the model pool affected by the Ford Safety Recall 24S75 (NHTSA Campaign 24V951000) and the expanded 25SB8 camera recall. I am filing this to document the active failure of this safety component on my specific VIN [XXX]. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11754437
40,000 miles · Jul 28, 2026
Back Over Prevention
The contact owns a 2019 Ford Flex. The contact received notifications of NHTSA Campaign Numbers: 25V695000 (Back Over Prevention) and 25V829000 (Structure); however, the parts to do the recall repairs were not yet available. The contact stated that while reversing, the rearview camera was inoperable. Additionally, the driver's s…
Read full complaint
The contact owns a 2019 Ford Flex. The contact received notifications of NHTSA Campaign Numbers: 25V695000 (Back Over Prevention) and 25V829000 (Structure); however, the parts to do the recall repairs were not yet available. The contact stated that while reversing, the rearview camera was inoperable. Additionally, the driver's side door B-Pillar trim had detached from the vehicle. The vehicle was taken to the dealer, where the contact was informed that the part for the repair of NHTSA Campaign Number: 25V695000 (Back Over Prevention); was only available for Mustang vehicles. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not contacted. The failure mileage was approximately 40,000.
NHTSA ODI #11753273
81,000 miles · Jul 27, 2026
Structure
The contact owns a 2019 Ford Flex. The contact stated that while driving at an undisclosed speed, the B-pillar trim detached. The contact taped the trim to keep it from flopping around. The dealer was contacted, and the vehicle was repaired. The contact associated the failure with NHTSA Campaign Number: 25V829000 (Structure). Th…
Read full complaint
The contact owns a 2019 Ford Flex. The contact stated that while driving at an undisclosed speed, the B-pillar trim detached. The contact taped the trim to keep it from flopping around. The dealer was contacted, and the vehicle was repaired. The contact associated the failure with NHTSA Campaign Number: 25V829000 (Structure). The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair, to be refunded by the dealer once parts became available. The manufacturer was not made aware of the issue. The failure mileage was approximately 81,000.
NHTSA ODI #11753057
Mileage unknown · Jul 26, 2026
Structure
B pillar (keypad) on drivers side flew off on the highway and cracked in half, the lower part was still attached to the wiring harness. The upper part flew onto the roadway. I had to pull over and strap the lower part to the window/door frame and drive the rest of the way with my window down in hot weather for 60+ miles. This is…
Read full complaint
B pillar (keypad) on drivers side flew off on the highway and cracked in half, the lower part was still attached to the wiring harness. The upper part flew onto the roadway. I had to pull over and strap the lower part to the window/door frame and drive the rest of the way with my window down in hot weather for 60+ miles. This is part of a recall, but no remedy is currently available from Ford.
NHTSA ODI #11752867
40,000 miles · Jul 22, 2026
Back Over Prevention
The contact owns a 2019 Ford Flex. The contact stated that while the vehicle was in reverse(R), the rear-view camera displayed a blank image or an inverted image. The contact received notification of NTHSA Campaign Number: 24V951000 (Back Over Prevention); the contact associated the failure with the recall. The local dealer was …
Read full complaint
The contact owns a 2019 Ford Flex. The contact stated that while the vehicle was in reverse(R), the rear-view camera displayed a blank image or an inverted image. The contact received notification of NTHSA Campaign Number: 24V951000 (Back Over Prevention); the contact associated the failure with the recall. The local dealer was contacted; however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was approximately 40,000.
NHTSA ODI #11752122
Mileage unknown · Jul 21, 2026
Back Over Prevention
The contact owns a 2019 Ford Flex. The contact stated that the rear-view camera became inoperable. The camera image was displayed upside down. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention). The local dealer was contacted, but the vehicle was not diagnosed or repaired. The manufactur…
Read full complaint
The contact owns a 2019 Ford Flex. The contact stated that the rear-view camera became inoperable. The camera image was displayed upside down. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention). The local dealer was contacted, but the vehicle was not diagnosed or repaired. The manufacturer was not contacted. The failure mileage was unknown.
NHTSA ODI #11751733
50,000 miles · Jul 17, 2026
Back Over Prevention
The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while reversing, the rearview camera displayed a blank image. The vehicle was taken to the dealer to be inspecte…
Read full complaint
The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 25V695000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while reversing, the rearview camera displayed a blank image. The vehicle was taken to the dealer to be inspected, and the contact was informed that the part to repair the vehicle was unavailable. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 50,000.
NHTSA ODI #11751095
Official recalls
4Oct 24, 2025
Ford Motor Company (Ford) is recalling certain 2017-2019 Flex vehicles. The driver and front passenger B-Pillar door trim may detach while driving.
Consequence & remedy
Consequence: Door trim that detaches while driving can create a road hazard, increasing the risk of a crash.
Remedy: Dealers will repair or replace the B-pillar trim as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed December 17, 2025. Additional letters will be sent once the remedy is available, anticipated March 2027. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SB8. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 28, 2025.
Oct 13, 2025
Ford Motor Company (Ford) is recalling certain 2015-2019 Flex, 2015 Explorer, Lincoln MKT, Lincoln MKZ, 2015-2016 C-Max, Escape, Taurus, 2016 Fusion, 2018-2019 Taurus, 2019 Lincoln MKT, Fiesta, and 2020 Mustang vehicles. The rearview camera may display a distorted, intermittent, or blank image when the vehicle is in reverse.
Consequence & remedy
Consequence: A rearview camera that fails to properly display an image can reduce the driver’s view behind the vehicle, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the rearview camera as necessary, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on October 25, 2025. Additional letters will be mailed once the final remedy is available on each phase. Mustang owner notification letters were mailed January 2, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA9. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 14, 2025.
Dec 20, 2024
Ford Motor Company (Ford) is recalling certain 2019 Flex, Fiesta, and Lincoln MKT vehicles. The rearview camera may intermittently display a blank or distorted image.
Consequence & remedy
Consequence: A rearview camera that displays a blank or distorted image can reduce the drivers view of what is behind the vehicle, increasing the risk of a crash.
Remedy: Dealers will replace the rearview camera as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed January 22, 2025. A second notice will be sent once the final remedy is available, anticipated March 2027. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S75.
Aug 20, 2018
Ford Motor Company (Ford) is recalling certain 2018 Ford Edge, Lincoln MKX, 2019 Ford Flex, and Lincoln MKT vehicles. The power supply cables at the starter and the alternator may not have been properly secured, possibly resulting in an electrical arc.
Consequence & remedy
Consequence: An electrical arc can increase the risk of a fire.
Remedy: Ford will notify owners, and dealers will inspect the alternator and starter motor power supply cables to verify that they are properly secured, correcting them as necessary, free of charge. The recall began September 26, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S25.
Additional source detail variants (2)
Electrical System:starter Assembly
Ford Motor Company (Ford) is recalling certain 2018 Ford Edge, Lincoln MKX, 2019 Ford Flex, and Lincoln MKT vehicles. The power supply cables at the starter and the alternator may not have been properly secured, possibly resulting in an electrical arc.
Consequence: An electrical arc can increase the risk of a fire.
Remedy: Ford will notify owners, and dealers will inspect the alternator and starter motor power supply cables to verify that they are properly secured, correcting them as necessary, free of charge. The recall began September 26, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S25.
Electrical System:alternator/generator/regulator
Ford Motor Company (Ford) is recalling certain 2018 Ford Edge, Lincoln MKX, 2019 Ford Flex, and Lincoln MKT vehicles. The power supply cables at the starter and the alternator may not have been properly secured, possibly resulting in an electrical arc.
Consequence: An electrical arc can increase the risk of a fire.
Remedy: Ford will notify owners, and dealers will inspect the alternator and starter motor power supply cables to verify that they are properly secured, correcting them as necessary, free of charge. The recall began September 26, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S25.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2PE25007 · B-Pillar Trim Detachment
Opened Aug 7, 2025 · Closed Aug 5, 2026
Status: closed (inferred from source dates) · Structure:body:roof And Pillars
On August 7, 2025, the Office of Defects Investigation (ODI) opened PE25007 to investigate instances of B-pillar trim detachment in model year (MY) 2019 Ford Flex vehicles manufactured by Ford Motor Company. During the investigation, MY 2011-2018 Ford Flex vehicles were analyzed as peer vehicles, and subsequently incorporated into the subject population because they use B-pillar trim pieces that are substantially similar to those used on the MY 2019 Ford Flex vehicles. In July 2025, prior to the opening of PE25007, ODI and Ford met to discuss B-pillar trim detachment in Ford Flex vehicles. Ford reported that its warranty analysis indicated that Flex B-pillar trim had a low detachment rate and that Ford did not believe this condition posed an unreasonable risk to motor vehicle safety. In July 2025, Ford closed its internal investigation. Because ODI’s analysis of complaint data indicated a high failure rate and an increasing failure trend, PE25007 was subsequently opened. In responding to the information request for PE25007, Ford reassessed the warranty search criteria used in its July 2025 internal investigation. The reassessment found the detachment rate to be substantially higher than what Ford had originally determined. Consequently, in October 2025, Ford issued recall 25V732based on the reassessed and accurate high failure rate. This recall instructed dealers to inspect the driver and front passenger B-pillar trim pieces and repair/replace if necessary. The vehicles included in this recall were MY 2017-2019 Ford Flex with production dates between February 17, 2017 and December 2, 2019. In January 2026, Ford issued 25V732 Amendment 1, which updated the remedy to remove the inspection criteria and instead proactively secure the driver and front passenger B-pillar trim with adhesive. The scope of vehicles included in the recall was unchanged by Amendment 1. ODI’s analysis of 25V732 found that both the scope and remedy were insufficient and that an unreasonable safety risk remained despite the recall. MY 2016 Ford Flex was excluded from the recall scope and the rear B-pillar trims on both the driver and passenger side were excluded from the recall. The failure rates of both MY 2016 Ford Flex and rear B-pillar trim pieces were found to be higher than the failure rates in similar trim detachment recalls issued by both Ford and other vehicle manufacturers. Starting in January 2026, ODI and Ford had multiple meetings to discuss Ford’s PE25007 response data and ODI’s concern about the 25V732 scope and remedy. In June 2026, Ford issued 25V732 Amendment 2. This amendment expanded the scope of the recall to add MY 2016-2017 Ford Flex vehicles produced before February 17, 2017. Additionally, this amendment updated the remedy to include removal of and reapplication or replacement of both rear driver and rear passenger B-pillar trim pieces in addition to front driver and front passenger B-pillar trim pieces. This updated remedy applies to all MY 2016-2019 vehicles. Ford expects to complete the mailing of remedy owner notification letters by March 26, 2027. Also, Ford informed ODI that prior model year (MY 2011-2015) vehicles were referred to Ford’s Customer Satisfaction forum for consideration of an extended warranty program. In view of recall 25V732 and its associated amendments, ODI is closing this Preliminary Evaluation (PE). The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE24030 · Rear-view Camera Failure
Opened Oct 11, 2024 · Closed Feb 2, 2026
Status: closed (inferred from source dates) · Back Over Prevention: Sensing System: Camera
On October 11, 2024, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24030) to assess alleged failures of the rear-view camera in Model Year (MY) 2019 Ford Flex vehicles. Complaints submitted to NHTSA through Vehicle Online Questionnaires (VOQs), reviewed by ODI, report blank, distorted, or inverted rear-view camera images when in reverse. An inverted or upside-down image can provide false information to the driver increasing the risk of a crash. To date, ODI has received 85 VOQ complaints and additional EWR Field Reports with these allegations for MY 2019 Ford Flex vehicles. During the investigation, ODI found that the MY 2019 Ford Flex vehicle and certain peer vehicles including MY 2015-2018 Flex, MY 2019 Fiesta, Taurus, and Lincoln MKT vehicles are equipped with Magna analog rear-view-only cameras. On December 20, 2024, Ford filed Recall 24V-951 covering 30,715 MY 2019 Ford Flex, Ford Fiesta, and Lincoln MKT vehicles in which the rear-view camera may intermittently display a blank or distorted image. The dealers will replace the rear-view camera for vehicles in the recall population. Per the recall chronology, teardown of three cameras identified fractured solder joints between the microcontroller and the printed circuit board. Ford indicated that other causal factors are being investigated and asserted that the defect is contained within the camera. ODI found that certain peer vehicles excluded from Recall 24V-951 showed a high rate of VOQ complaints. Also, ODI identified reports produced by Ford that indicate the peer vehicles have the same issue as the subject vehicles. To address ODI’s concern, Ford analyzed some field-returned cameras, as well as Ford’s field data and ODI’s VOQ data. Ford stated it did not identify a specific root cause in the Magna supplied cameras. However, on October 13, 2025, Ford filed Recall 25V-695 covering 1,448,655 vehicles of various Ford/Lincoln models equipped with Magna supplied cameras. The cameras demonstrate the same blank or distorted images that prompted Recall 24V-951. It should be noted that Ford is conducting a recall of those vehicles by model/model year that exhibit VOQ complaint rates greater than 10 per 100,000 vehicles. For the remaining vehicles (rates less than 10/100K), Ford is providing a warranty extension (15 years/unlimited miles). Ford has stated that the differences in the rates (field performance) are likely due to the differences in the camera related hardware, such as the wiring harness type that are specific by vehicle model/model year. In view of Ford filing Recall 24V-951 and Recall 25V-695 addressing the subject of this investigation, ODI is closing this Preliminary Evaluation. NHTSA reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Back Over Prevention: Sensing System: Camera
On October 11, 2024, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24030) to assess alleged failures of the rear-view camera in Model Year (MY) 2019 Ford Flex vehicles. Complaints submitted to NHTSA through Vehicle Online Questionnaires (VOQs), reviewed by ODI, report blank, distorted, or inverted rear-view camera images when in reverse. An inverted or upside-down image can provide false information to the driver increasing the risk of a crash. To date, ODI has received 85 VOQ complaints and additional EWR Field Reports with these allegations for MY 2019 Ford Flex vehicles. During the investigation, ODI found that the MY 2019 Ford Flex vehicle and certain peer vehicles including MY 2015-2018 Flex, MY 2019 Fiesta, Taurus, and Lincoln MKT vehicles are equipped with Magna analog rear-view-only cameras. On December 20, 2024, Ford filed Recall 24V-951 covering 30,715 MY 2019 Ford Flex, Ford Fiesta, and Lincoln MKT vehicles in which the rear-view camera may intermittently display a blank or distorted image. The dealers will replace the rear-view camera for vehicles in the recall population. Per the recall chronology, teardown of three cameras identified fractured solder joints between the microcontroller and the printed circuit board. Ford indicated that other causal factors are being investigated and asserted that the defect is contained within the camera. ODI found that certain peer vehicles excluded from Recall 24V-951 showed a high rate of VOQ complaints. Also, ODI identified reports produced by Ford that indicate the peer vehicles have the same issue as the subject vehicles. To address ODI’s concern, Ford analyzed some field-returned cameras, as well as Ford’s field data and ODI’s VOQ data. Ford stated it did not identify a specific root cause in the Magna supplied cameras. However, on October 13, 2025, Ford filed Recall 25V-695 covering 1,448,655 vehicles of various Ford/Lincoln models equipped with Magna supplied cameras. The cameras demonstrate the same blank or distorted images that prompted Recall 24V-951. It should be noted that Ford is conducting a recall of those vehicles by model/model year that exhibit VOQ complaint rates greater than 10 per 100,000 vehicles. For the remaining vehicles (rates less than 10/100K), Ford is providing a warranty extension (15 years/unlimited miles). Ford has stated that the differences in the rates (field performance) are likely due to the differences in the camera related hardware, such as the wiring harness type that are specific by vehicle model/model year. In view of Ford filing Recall 24V-951 and Recall 25V-695 addressing the subject of this investigation, ODI is closing this Preliminary Evaluation. NHTSA reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Back Over Prevention: Sensing System: Camera
On October 11, 2024, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24030) to assess alleged failures of the rear-view camera in Model Year (MY) 2019 Ford Flex vehicles. Complaints submitted to NHTSA through Vehicle Online Questionnaires (VOQs), reviewed by ODI, report blank, distorted, or inverted rear-view camera images when in reverse. An inverted or upside-down image can provide false information to the driver increasing the risk of a crash. To date, ODI has received 85 VOQ complaints and additional EWR Field Reports with these allegations for MY 2019 Ford Flex vehicles. During the investigation, ODI found that the MY 2019 Ford Flex vehicle and certain peer vehicles including MY 2015-2018 Flex, MY 2019 Fiesta, Taurus, and Lincoln MKT vehicles are equipped with Magna analog rear-view-only cameras. On December 20, 2024, Ford filed Recall 24V-951 covering 30,715 MY 2019 Ford Flex, Ford Fiesta, and Lincoln MKT vehicles in which the rear-view camera may intermittently display a blank or distorted image. The dealers will replace the rear-view camera for vehicles in the recall population. Per the recall chronology, teardown of three cameras identified fractured solder joints between the microcontroller and the printed circuit board. Ford indicated that other causal factors are being investigated and asserted that the defect is contained within the camera. ODI found that certain peer vehicles excluded from Recall 24V-951 showed a high rate of VOQ complaints. Also, ODI identified reports produced by Ford that indicate the peer vehicles have the same issue as the subject vehicles. To address ODI’s concern, Ford analyzed some field-returned cameras, as well as Ford’s field data and ODI’s VOQ data. Ford stated it did not identify a specific root cause in the Magna supplied cameras. However, on October 13, 2025, Ford filed Recall 25V-695 covering 1,448,655 vehicles of various Ford/Lincoln models equipped with Magna supplied cameras. The cameras demonstrate the same blank or distorted images that prompted Recall 24V-951. It should be noted that Ford is conducting a recall of those vehicles by model/model year that exhibit VOQ complaint rates greater than 10 per 100,000 vehicles. For the remaining vehicles (rates less than 10/100K), Ford is providing a warranty extension (15 years/unlimited miles). Ford has stated that the differences in the rates (field performance) are likely due to the differences in the camera related hardware, such as the wiring harness type that are specific by vehicle model/model year. In view of Ford filing Recall 24V-951 and Recall 25V-695 addressing the subject of this investigation, ODI is closing this Preliminary Evaluation. NHTSA reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Illustration