IllustrationThe transmission started slipping in 1st and 2nd gear.
2016 Ford Fiesta
Owner reports · Recalls · Investigations
More warning signs than most Fiesta years
Owner complaints for the 2016 Ford Fiesta are substantially higher than the model-year median of 74.
About this comparison →How this year compares
Owner complaints by model year
Compare all Fiesta years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
240–25K
2325–50K
3250–75K
1875–100K
18100–150K
2150K+
117 reports with mileage · 61 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 101 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 33 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 26 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
10 crash reports1 fire reports6 injury reports
Power Train complaints
101 reportsI have come to find that this vehicle suffers from premature slave cylinder failure, there are roughly 62,000 miles on the vehicle. Typical failure is reported to Ford between 70,000 and 80,000 miles. First symptoms appeared at roughly 58,000 miles. As I am a single father and a full time communications worker, I was not able to…
Read full complaint
I have come to find that this vehicle suffers from premature slave cylinder failure, there are roughly 62,000 miles on the vehicle. Typical failure is reported to Ford between 70,000 and 80,000 miles. First symptoms appeared at roughly 58,000 miles. As I am a single father and a full time communications worker, I was not able to address this issue immediately upon discovering the initial symptoms as it would need further diagnosis. Clutch hydraulic fluids appear to be well sealed and clean. The design flaw with this system should be relatively obvious to a major automobile manufacturer such as Ford. The excessive temperatures caused by the transmission can and will affect any hydraulic systems severely. There are no avenues in which the temperatures can escape due to the bell housing of the transmission encasing the slave cylinder. In my experience as a prior automotive technician, most manual transmission automobiles place the cylinder in a more reasonable location, for example, beside the break booster in a 1991 Dodge Stealth. When observing the firewall in this location on this model of vehicle I can confidently say there is enough room to place a clutch slave cylinder in this location. The current placement appears to be for no other reason then planned obsolescence. Vehicle has stalled in traffic multiple times, cannot complete shifts due to clutch pedal sticking to floor. Inability to properly operate transmission as expected per mileage with a manual vehicle is a safety hazard. This is a safety concern due to limited ability to engage warning lights being that the shifter needs to be operated as well as the vehicle needing to be steered. Inability to depress the clutch to mechanical certainty limits the drivers ability to confidently navigate to a safe area to assess the vehicle's possible malfunctions. This limits the ability to warn other motorists on the roadways, which can cause accidents that may also cause injury/fatality depending on the speeds driven.
The contact owns a 2016 Ford Fiesta. The contact stated while depressing the accelerator pedal, the vehicle failed to respond as intended and hesitated to respond. Additionally, the vehicle failed to reverse as intended. Several unknown warning lights were illuminated. The vehicle was taken to a dealer, where it was diagnosed th…
Read full complaint
The contact owns a 2016 Ford Fiesta. The contact stated while depressing the accelerator pedal, the vehicle failed to respond as intended and hesitated to respond. Additionally, the vehicle failed to reverse as intended. Several unknown warning lights were illuminated. The vehicle was taken to a dealer, where it was diagnosed that the transmission had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure, but no assistance was provided, and the contact was informed that the VIN was not under recall. The failure mileage was 70,000.
The contact owns a 2016 Ford Fiesta. The contact stated while driving approximately 60 MPH, the vehicle was losing motive power. The check engine warning light was illuminated. The vehicle was taken to the dealer to be diagnosed and it was determined that the spark plugs needed to be replaced. The vehicle was repaired; however, …
Read full complaint
The contact owns a 2016 Ford Fiesta. The contact stated while driving approximately 60 MPH, the vehicle was losing motive power. The check engine warning light was illuminated. The vehicle was taken to the dealer to be diagnosed and it was determined that the spark plugs needed to be replaced. The vehicle was repaired; however, the failure reoccurred. The vehicle was taken back to the same dealer who diagnosed the vehicle and determined that the ignition coils needed to be replaced. The vehicle was repaired; however, the failure reoccurred. The vehicle was taken to an independent mechanic who diagnosed the vehicle and determined that the TCM needed to be replaced. The vehicle was not repaired. The contact researched online and related the failure to Customer Satisfaction Program: 14M02 (Power Train); however, the VIN was not included. The manufacturer was informed of the failure and referred the contact to NHTSA Hotline to report the failure. The failure mileage was approximately 130,000.
Symptoms: No-start condition (wouldn't crank w/o jump); delayed or harsh shifting; lost power (stalled going up tiny hill). Warning lights: transmission malfunction - service now; check engine light. Our symptoms and warning lights are consistent with Ford's Fiesta Transmission Control Module recall, however the VIN for our car …
Read full complaint
Symptoms: No-start condition (wouldn't crank w/o jump); delayed or harsh shifting; lost power (stalled going up tiny hill). Warning lights: transmission malfunction - service now; check engine light. Our symptoms and warning lights are consistent with Ford's Fiesta Transmission Control Module recall, however the VIN for our car is not part of the original recall. We meet all of Ford's recall eligibility criteria: reported before June 30, 2025; vehicle is less than 10 years old; vehicle has fewer than 150,000 miles. By virtue of the symptoms, warning lights and meeting Ford's other criteria strongly suggest our VIN should be included in the recall.
The contact owns a 2016 Ford Fiesta. The contact stated that while driving at various speeds, the transmission was slipping, causing the vehicle to lost motive power or stall. The contact was able to coast over to the side of the road and waited approximately 10 minutes before restarting the vehicle. The contact stated that seve…
Read full complaint
The contact owns a 2016 Ford Fiesta. The contact stated that while driving at various speeds, the transmission was slipping, causing the vehicle to lost motive power or stall. The contact was able to coast over to the side of the road and waited approximately 10 minutes before restarting the vehicle. The contact stated that several attempts were needed to restart the vehicle. The contact stated that the vehicle failed to restart intermittently. The contact stated that DTC: PO606 was displayed; indicating a failure with the Powertrain Control Module (PCM). The vehicle was taken to a certified mechanic who diagnosed and determined that the PCM had failed and needed to be replaced. The vehicle was not repaired. The contact found information about the Technical Service Bulletin: 16/0129 with the NHTSA ID Number: 10109047 (Power Train) and the Customer Service Program: 14M02 with NHTSA ID Number: 10057231 (Power Train); however, the vehicle was not included. The manufacturer was informed of the failure. The manufacturer transferred the contact to the NHTSA Hotline to report the failure. The failure mileage was 85,000.
The TCM was defective. It has been known that the TCM, transmission control modules are defective for Ford Fiestas and Focus. My daughter was driving the car and it stalled. If she was in heavy traffic are making a turn when this happened she could have been seriously injured. Ford said that they fixed this issue in the 2015 edi…
Read full complaint
The TCM was defective. It has been known that the TCM, transmission control modules are defective for Ford Fiestas and Focus. My daughter was driving the car and it stalled. If she was in heavy traffic are making a turn when this happened she could have been seriously injured. Ford said that they fixed this issue in the 2015 editions, that's why they stop the recall for 2016 models, but they really did not fix the problem. The vehicle was taken to a Ford dealership in Wisconsin and they confirmed all this information to me. And eight hundred dollars was paid to fix a problem that is on a recall for most models except the 2016, because they supposedly fixed the problem.
The contact owns a 2016 Ford Fiesta. The contact stated while driving at an undisclosed speed, the transmission unexpectedly downshifted. There was no warning light illuminated. The dealer was contacted; however, the vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure and referred the contact to…
Read full complaint
The contact owns a 2016 Ford Fiesta. The contact stated while driving at an undisclosed speed, the transmission unexpectedly downshifted. There was no warning light illuminated. The dealer was contacted; however, the vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure and referred the contact to the NHSTA Hotline for assistance. The failure mileage was approximately 128,000.
The contact owns a 2016 Ford Fiesta. The contact stated while driving at an undisclosed speed, the accelerator pedal was depressed; however, the vehicle failed to accelerate above 20 MPH. The contact stated that the transmission warning light was illuminated. In addition, the contact stated that when the gear shifter was shifted…
Read full complaint
The contact owns a 2016 Ford Fiesta. The contact stated while driving at an undisclosed speed, the accelerator pedal was depressed; however, the vehicle failed to accelerate above 20 MPH. The contact stated that the transmission warning light was illuminated. In addition, the contact stated that when the gear shifter was shifted into drive, the vehicle quickly lunged forward. The vehicle was taken to the dealer where it was diagnosed with transmission control module failure. The contact was informed that the transmission control module needed to be replaced. The vehicle was repaired. The contact referenced an unknown recall however, the contact was informed that the VIN was not under recall. The manufacturer was made aware of the failure but provided no assistance. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 37,000.
The contact owns a 2016 Ford Fiesta. The contact stated while driving 25-30 MPH, the vehicle was shuddering as if it would stall, and the vehicle made an abnormal whining sound. The contact stated that the failure also occurred while driving over a speed bump. The contact had noticed that the failure mostly occurred while drivin…
Read full complaint
The contact owns a 2016 Ford Fiesta. The contact stated while driving 25-30 MPH, the vehicle was shuddering as if it would stall, and the vehicle made an abnormal whining sound. The contact stated that the failure also occurred while driving over a speed bump. The contact had noticed that the failure mostly occurred while driving at low speeds and while the RPMs were low. Additionally, the contact stated that the transmission was slipping while driving and making right turns. There was no warning light illuminated. The vehicle was taken to the dealer, where it was diagnosed that the transmission clutch assembly had failed and needed to be replaced. The dealer determined that the failure was related to an undisclosed recall. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that no assistance could be provided unless the VIN was added to the unknown recall. The failure mileage was approximately 71,600.
Official recalls
0No recalls in this snapshot.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA26004 · Timing Belt Failure
Opened Jul 31, 2026 · No close date supplied
Status: open (inferred from source dates) · Engine; Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE25020 · Timing Belt Failure
Opened Dec 18, 2025 · Closed Jul 31, 2026
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.