NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
585 reports58,000 miles · Jul 23, 2012
Seat Belts
THE PASSENGER SIDE SEAT BELT HAS BECOME UNUSABLE DUE TO NOT COMING OUT TO BE ABLE TO BELT IN PASSENGERS. ALSO, IT WILL NOT RETRACT FULLY. THIS IS A SERIOUS SAFETY ISSUE, DUE TO SEAT BELT LAWS AND REGULATIONS AND PASSENGER SAFETY ISSUES, AND SHOULD BE ADDRESSED AND FIXED ON ANY FORD THAT IS HAVING SUCH ISSUES OR SIMILAR ISSUES…
Read full complaint
THE PASSENGER SIDE SEAT BELT HAS BECOME UNUSABLE DUE TO NOT COMING OUT TO BE ABLE TO BELT IN PASSENGERS. ALSO, IT WILL NOT RETRACT FULLY. THIS IS A SERIOUS SAFETY ISSUE, DUE TO SEAT BELT LAWS AND REGULATIONS AND PASSENGER SAFETY ISSUES, AND SHOULD BE ADDRESSED AND FIXED ON ANY FORD THAT IS HAVING SUCH ISSUES OR SIMILAR ISSUES. *TR
NHTSA ODI #10467165
43,000 miles · Jul 16, 2012
Engine And Engine CoolingFire
ON JULY 1, 2012, MY 2006 FORD F-150 SUPER CREW TRUCK CAUGHT ON FIRE WHILE SITTING IN MY DRIVEWAY. THE TRUCK HAD BEEN SITTING UNTOUCHED FOR A WEEK WHEN IT CAUGHT ON FIRE WITHOUT ANY EXPLANATION. FIRE INVESTIGATORS WERE UNABLE TO DETERMINE THE CAUSE OF THE FIRE BECAUSE THE TRUCK WAS APPROXIMATELY 90% BURNED. *TR
NHTSA ODI #10465877
40,000 miles · Jul 8, 2012
Steering
STEERING BECAME VERY HARD TO TURN. WOULD NOT CENTER AFTER TURNING, WOULD LOCK ON WET ROADS. I HAD TO TURN THE STEERING WHEEL BY HAND TO GET IT BACK TO CENTER. I CHECKED TO FIND THE U JOINTS ON STEERING SHAFT WHERE RUSTED SO I LUBED WITH OIL. STEERING BECAME MUCH BETTER. I WENT TO A LOCAL FORD DEALER THEY SAID THERE WAS NO RECALL…
Read full complaint
STEERING BECAME VERY HARD TO TURN. WOULD NOT CENTER AFTER TURNING, WOULD LOCK ON WET ROADS. I HAD TO TURN THE STEERING WHEEL BY HAND TO GET IT BACK TO CENTER. I CHECKED TO FIND THE U JOINTS ON STEERING SHAFT WHERE RUSTED SO I LUBED WITH OIL. STEERING BECAME MUCH BETTER. I WENT TO A LOCAL FORD DEALER THEY SAID THERE WAS NO RECALLS AND KNEW OF NO PROBLEMS WITH THE STEERING ON THE F150'S. THE FORD DEALER WANTED ME TO LET THEM TAKE EVERYTHING APART BUT SAID IT COULD RUN INTO A LOT OF MONEY DEPENDING ON WHAT THEY FIND. SO FOR OVER THREE YEARS I'VE BEEN OILING THE JOINTS ON THE SHAFT AND LIVING WITH THE PROBLEM. WAITING FOR TOTAL FAILURE TO SUE FORD FOR POOR DESIGN OF THE STEERING COLUMN SHAFT JOINTS. *TR
NHTSA ODI #10464614
82,150 miles · Jul 5, 2012
Air BagsElectrical System
I WAS DRIVING ON THE HIGHWAY WHEN ALL OF MY GAUGES WENT DEAD INCLUDING THE SPEEDOMETER, A COUPLE OF MINUTES LATER THEY CAME BACK ON AND WHEN THEY DID THE AIRBAG WARNING LIGHT STARTED BLINKING RAPIDLY. A FEW MOMENTS LATER THE GAUGES WENT DEAD AGAIN, WHEN THEY CAME BACK ON THE SECOND TIME THE AIRBAG WARNING LIGHT STARTED BLINKING …
Read full complaint
I WAS DRIVING ON THE HIGHWAY WHEN ALL OF MY GAUGES WENT DEAD INCLUDING THE SPEEDOMETER, A COUPLE OF MINUTES LATER THEY CAME BACK ON AND WHEN THEY DID THE AIRBAG WARNING LIGHT STARTED BLINKING RAPIDLY. A FEW MOMENTS LATER THE GAUGES WENT DEAD AGAIN, WHEN THEY CAME BACK ON THE SECOND TIME THE AIRBAG WARNING LIGHT STARTED BLINKING RAPIDLY AND ERRATICALLY. SINCE THAT TIME MY GAUGES HAVE FAILED 3 MORE TIMES WITH THE SAME BEHAVIOR FROM THE AIRBAG WARNING LIGHT. I DID SOME RESEARCH ONLINE AND FOUND THAT EVEN THOUGH FORD HAS NOT RECALLED THIS PROBLEM IT HAS BEEN EXPERIENCED BY HUNDREDS OF 2006 FORD F150 OWNERS. *TR
NHTSA ODI #10464353
71,000 miles · Jul 4, 2012
EngineFuel System, Gasoline
I HAD A FUEL INJECTOR FAIL THAT COMPLETELY RUINED THE ENGINE AT 71K MILES. I HAD TO HAVE IT REPLACED. I WAS VERY SURPRISED TO SEE THAT MY PROBLEM WAS EXACTLY LIKE THE FORD 2005 CUSTOMER SATISFACTION PROGRAM 07M08 PROBLEM. MY TRUCK WAS BUILT IN 2005, BUT TITLED AS A 2006. I HAVE TALKED AND WROTE TO FORD BUT THEY WOULD NOT HEL…
Read full complaint
I HAD A FUEL INJECTOR FAIL THAT COMPLETELY RUINED THE ENGINE AT 71K MILES. I HAD TO HAVE IT REPLACED. I WAS VERY SURPRISED TO SEE THAT MY PROBLEM WAS EXACTLY LIKE THE FORD 2005 CUSTOMER SATISFACTION PROGRAM 07M08 PROBLEM. MY TRUCK WAS BUILT IN 2005, BUT TITLED AS A 2006. I HAVE TALKED AND WROTE TO FORD BUT THEY WOULD NOT HELP ME. I TOLD THEM I STILL HAVE THE FAILED INJECTOR AND THEY WOULDN'T EVEN LOOK AT IT TO SEE IF IT WAS ONE OF THE DEFECTIVE PARTS THAT SPURRED THE 07M08 PROGRAM. I BELIEVE FORD NEEDS TO EXPAND THE CUSTOMER SATISFACTION PROGRAM 07M08 TO INCLUDE 2006 MODELS. I WOULD LOVE FOR THE NHTSA TO PRESSURE FORD TO REVISIT THIS ISSUE. THIS WAS HARD FOR ME BECAUSE I STILL HAVE THE INJECTOR THAT FAILED. I KEEP IT AS A REMINDER OF THE $8,000 I HAD TO SPEND ON A NEW ENGINE. I BELIEVE THE NHTSA SHOULD PRESSURE FORD TO ADMIT WHICH INJECTORS WERE AN ISSUE SO PEOPLE LIKE ME HAVE LEVERAGE TO FIGHT GIANTS LIKE FORD THAT IN THIS CASE SCREWED THEIR CUSTOMER. *JS
NHTSA ODI #10464197
Mileage unknown · Jun 15, 2012
Structure
TL* THE CONTACT OWNS A 2006 FORD F-150. THE CONTACT STATED THAT BOTH OF THE DECALS ON THE VEHICLE WERE FADED AND DELAMINATED. THE VEHICLE WAS NOT REPAIRED AND THE MANUFACTURER WAS NOT CONTACTED. UPDATED 07/13/12*LJ UPDATED 07/17/12
NHTSA ODI #10461895
72,000 miles · Jun 14, 2012
Engine And Engine Cooling
TL* THE CONTACT OWNS A 2006 FORD F150. THE CONTACT TOOK THE VEHICLE FOR A ROUTINE OIL CHANGE WHEN HE WAS ADVISED BY THE MECHANIC THAT FOUR OF THE SPARK PLUGS WERE UNABLE TO BE REMOVED FOR REPLACEMENT. THE SPARK PLUGS WERE NOT OF GOOD QUALITY AND WOULD NEED TO BE REPLACED MORE OFTEN THAN USUAL. THE MANUFACTURER WAS MADE AWARE, HO…
Read full complaint
TL* THE CONTACT OWNS A 2006 FORD F150. THE CONTACT TOOK THE VEHICLE FOR A ROUTINE OIL CHANGE WHEN HE WAS ADVISED BY THE MECHANIC THAT FOUR OF THE SPARK PLUGS WERE UNABLE TO BE REMOVED FOR REPLACEMENT. THE SPARK PLUGS WERE NOT OF GOOD QUALITY AND WOULD NEED TO BE REPLACED MORE OFTEN THAN USUAL. THE MANUFACTURER WAS MADE AWARE, HOWEVER NO ASSISTANCE WAS PROVIDED. THE VIN WAS UNAVAILABLE. THE APPROXIMATE CURRENT AND FAILURE MILEAGE WAS 72,000.
NHTSA ODI #10461713
65,000 miles · Jun 2, 2012
Electrical SystemVisibility
THE PASSENGER IN MY VEHICLE TRIED ROLLING UP THE WINDOW WHILE AT A STOPLIGHT AND IT WOULD NOT GO UP. THE WINDOW SWITCH WILL WORK TO ROLL THE WINDOW DOWN BUT NOT TO ROLL IT UP. AFTER APPROXIMATELY 11 MONTHS THE DRIVERS SIDE WINDOW IS DOING THE SAME THING, WILL GO DOWN BUT NOT UP. WITH THE WINDOW STUCK IN THE DOWN POSITION, MY VEH…
Read full complaint
THE PASSENGER IN MY VEHICLE TRIED ROLLING UP THE WINDOW WHILE AT A STOPLIGHT AND IT WOULD NOT GO UP. THE WINDOW SWITCH WILL WORK TO ROLL THE WINDOW DOWN BUT NOT TO ROLL IT UP. AFTER APPROXIMATELY 11 MONTHS THE DRIVERS SIDE WINDOW IS DOING THE SAME THING, WILL GO DOWN BUT NOT UP. WITH THE WINDOW STUCK IN THE DOWN POSITION, MY VEHICLE IS NOW EXPOSED TO THE ELEMENTS, RAIN PARTICULARLY, AND I FEAR THE WATER FROM THE RAIN IS GOING TO AFFECT THE REST OF MY DOOR SWITCHES, AND POSSIBLY RUIN THE LEATHER SEATS AND THE POWER FUNCTIONS FOR MY SEATS AS WELL. IT IS A DISTRACTION AND A HAZARD TO HAVE TO DRIVE WITH THE WINDOW DOWN CONSTANTLY. *TR
NHTSA ODI #10460377
26,032 miles · May 21, 2012
Power TrainVehicle Speed Control
TRANSMISSION SHIFT CABLE OUTER SHEATH WAS MELTED ON EXHAUST SYSTEM. CABLE HAD UNKNOWINGLY COME LOOSE OF A RETAINING CLIP AND WAS THEN ALLOWED TO CONTACT HOT EXHAUST MANIFOLD. MELTED THE OUTER PLASTIC OF SHIFT CABLE CAUSING THE SHIFT SELECTOR TO BECOME INOPERABLE. SHIFT SELECTOR COULD BE PLACED IN PARK BUT TRANSMISSION WOULD NOT …
Read full complaint
TRANSMISSION SHIFT CABLE OUTER SHEATH WAS MELTED ON EXHAUST SYSTEM. CABLE HAD UNKNOWINGLY COME LOOSE OF A RETAINING CLIP AND WAS THEN ALLOWED TO CONTACT HOT EXHAUST MANIFOLD. MELTED THE OUTER PLASTIC OF SHIFT CABLE CAUSING THE SHIFT SELECTOR TO BECOME INOPERABLE. SHIFT SELECTOR COULD BE PLACED IN PARK BUT TRANSMISSION WOULD NOT BE IN PARK; IF I HAD NOT REALIZED THERE WAS A PROBLEM I COULD HAVE BELIEVED THE TRANSMISSION WAS IN PARK WHEN IT WAS NOT AND THE TRUCK COULD HAVE ROLLED FREELY. TRUCK IS A WELL MAINTAINED 2006 FORD F150 CREW CAB 4X4 WITH THE COLUMN SHIFTER. *TT
NHTSA ODI #10459109
52,000 miles · Apr 11, 2012
Engine And Engine Cooling
TL* THE CONTACT OWNS A 2006 FORD F-150. WHILE TRAVELING 40 MPH, THE VEHICLE ATTEMPTED TO STALL AND WOULD NO LONGER ACCELERATE. THE VEHICLE WAS TAKEN TO A LOCAL MECHANIC WHERE THE CONTACT WAS INFORMED THAT THE FAILURE WAS CAUSED BY A BAD SPARK PLUG DESIGN. THE CONTACT WAS ALSO INFORMED THAT THE SPARKS HAD FRACTURED EACH TIME THE…
Read full complaint
TL* THE CONTACT OWNS A 2006 FORD F-150. WHILE TRAVELING 40 MPH, THE VEHICLE ATTEMPTED TO STALL AND WOULD NO LONGER ACCELERATE. THE VEHICLE WAS TAKEN TO A LOCAL MECHANIC WHERE THE CONTACT WAS INFORMED THAT THE FAILURE WAS CAUSED BY A BAD SPARK PLUG DESIGN. THE CONTACT WAS ALSO INFORMED THAT THE SPARKS HAD FRACTURED EACH TIME THEY ATTEMPTED TO REMOVE THE SPARK PLUGS. THE VEHICLE WAS NOT REPAIRED. THE CURRENT AND FAILURE MILEAGES WERE 52,000.
NHTSA ODI #10454899
Official recalls
4Feb 23, 2011
FORD IS RECALLING CERTAIN MODEL YEAR 2004-2006 F-150 PICK UP TRUCKS AS WELL AS CERTAIN MODEL YEAR 2006 LINCOLN MARK LT VEHICLES. IF THE CLOCKSPRING JUMPER WIRE COMES IN CONTACT WITH THE DRIVER SIDE FRONTAL AIR BAG LOWER HORN PLATE, THE WIRE INSULATION MAY BECOME CHAFED, CREATING A POTENTIAL FOR A SHORT CIRCUIT. IF THIS OCCURS THE AIR BAG WARNING LAMP MAY ILLUMINATE INDICATING THAT SERVICE IS REQUIRED.
Consequence & remedy
Consequence: THE DRIVER SIDE FRONTAL AIR BAG COULD INADVERTENTLY DEPLOY INCREASING THE RISK OF INJURY OR LOSS OF VEHICLE CONTROL IF OCCURRING WHILE IN MOTION.
Remedy: FORD WILL NOTIFY OWNERS AND INSTRUCT THEM TO TAKE THEIR VEHICLES TO A FORD OR LINCOLN/MERCURY DEALER TO HAVE A NEW CLOCKSPRING JUMPER WIRE INSTALLED THAT INCORPORATES A PROTECTIVE MESH COVER. REPAIRS WILL BE PERFORMED FREE OF CHARGE. THIS SAFETY RECALL BEGAN ON SOME VEHICLES IN MARCH 2011. THE RECALL CAMPAIGN ON THE EXPANDED POPULATION IS EXPECTED TO BEGIN ON OR ABOUT MAY 9, 2011. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
May 7, 2008
FORD IS RECALLING 605,684 MY 2005-2006 F-150 AND LINCOLN MARK LT VEHICLES EQUIPPED WITH 5.4L 3-VALVE ENGINES. THE BRAKE BOOSTER VACUUM SUPPLY HOSE ATTACHED TO THE INTAKE MANIFOLD FITTING MAY SWELL OVER TIME AND LOSE RETENTION FORCE. THIS CONDITION COULD ALLOW THE HOSE TO BECOME DETACHED FROM THE FITTING DURING AN INTAKE MANIFOLD BACKFIRE. SHOULD THE HOSE DETACH FROM THE INTAKE MANIFOLD, SEVERAL BRAKE APPLICATIONS WITH POWER ASSIST WILL BE AVAILABLE BEFORE THE VACUUM RESERVE IS DEPLETED.
Consequence & remedy
Consequence: ONCE THE BRAKE BOOSTER VACUUM RESERVE IS DEPLETED, THE DRIVER WILL HAVE FOUNDATION BRAKE FUNCTION, BUT WITH INCREASED BRAKE PEDAL EFFORT. REDUCED VEHICLE BRAKING COULD LEAD TO A CRASH.
Remedy: DEALERS WILL REPLACE A RUBBER HOSE ON THE BRAKE BOOSTER VACUUM SUPPLY TUBE ASSEMBLY. THE RECALL BEGAN ON JUNE 27, 2008. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
Feb 6, 2006
CERTAIN PICKUP TRUCKS FAIL TO COMPLY WITH EITHER THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 105, 'HYDRAULIC AND ELECTRIC BRAKE SYSTEMS' OR FMVSS NO. 135, 'PASSENGER CAR BRAKE SYSTEMS.' THESE VEHICLES WERE BUILT WITH A SOFTWARE ERROR IN THE INSTRUMENT CLUSTER.
Consequence & remedy
Consequence: THIS ERROR COULD PREVENT THE ANTILOCK BRAKE SYSTEM (ABS) WARNING LIGHT FROM ILLUMINATING IF THE ABS MODULE EVER BECAME INOPERATIVE.
Remedy: DEALERS WILL RECALIBRATE THE INSTRUMENT CLUSTER IN THESE VEHICLES. THE RECALL BEGAN ON FEBRUARY 27, 2006. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
Nov 9, 2005
ON CERTAIN TRUCKS, PASSENGER CARS AND SPORT UTILITY VEHICLES, THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN PRODUCED WITHOUT GREASE BEING APPLIED TO THE OUTPUT SHAFT GEAR.
Consequence & remedy
Consequence: AFTER A PERIOD OF CONTINUOUS USE ON THE HIGH SPEED SETTING, LACK OF GREASE ON THE OUTPUT SHAFT GEAR MAY CAUSE THE GEAR TO DISTORT OR FRACTURE DURING OPERATION RESULTING IN A LOSS OF WIPER FUNCTION. INOPERATIVE WIPERS UNDER INCLEMENT WEATHER CONDITIONS COULD CAUSE A CRASH DUE TO IMPAIRED VISIBILITY.
Remedy: DEALERS WILL INSPECT THE WIPER MOTOR FOR THE PRESENCE OF GREASE AND GREASE THE WIPER MOTOR GEARS IF NECESSARY. THE RECALL BEGAN ON NOVEMBER 22, 2005. OWNERS MAY CONTACT FORD AT 1-800-392-3673 OR LINCOLN/MERCURY AT 1-800-521-4140.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA10001 · Inadvertent Airbag Deployment
Opened Jan 13, 2010 · Closed Apr 25, 2011
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:sensor/control MODULE-INACTIVE
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Additional source detail variants (4)
Air Bags
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal:driver Side:inflator Module
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal:sensor/control MODULE-INACTIVE
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
PE08001 · Loss Of Brake POWER-ASSIST
Opened Jan 8, 2008 · Closed May 9, 2008
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist; Service Brakes, Hydraulic:power Assist:vacuum; Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Additional source detail variants (3)
Service Brakes, Hydraulic:power Assist
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Service Brakes, Hydraulic:power Assist:vacuum
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Illustration