NHTSA owner reports · September 18, 2026 snapshot.
Fuel System, Gasoline complaints
53 reportsClear category filter70 miles · Jan 27, 2010
Fuel System, Gasoline
FUEL INJECTIONS. I TOOK MY TRUCK IN FOR A WHISTLING PROBLEM. THEY PUT IT ON THE COMPUTER AND TOLD ME EVERYTHING LOOKED GREAT. NO PROBLEMS . TWO DAYS LATER THE TRUCK WAS IN THE DEALERSHIP BECACUSE OF A SMOKING PROBLEM AND THEY REPLACED FUEL INJECTOR #8. A COVERED SERVICE. FORD WAS AWARE OF THE PROBLEM BUT DID NOT SEND RECALL …
Read full complaint
FUEL INJECTIONS. I TOOK MY TRUCK IN FOR A WHISTLING PROBLEM. THEY PUT IT ON THE COMPUTER AND TOLD ME EVERYTHING LOOKED GREAT. NO PROBLEMS . TWO DAYS LATER THE TRUCK WAS IN THE DEALERSHIP BECACUSE OF A SMOKING PROBLEM AND THEY REPLACED FUEL INJECTOR #8. A COVERED SERVICE. FORD WAS AWARE OF THE PROBLEM BUT DID NOT SEND RECALL NOTICES. ONE WEEK LATER THE CHECK ENGINE LIGHT CAME ON, THE TRUCK WENT INTO THE SHOP AND THEY REPLACE FUEL INJECTOR # 1 AND #5. NOW I FIND OUT THAT FORD WILL NOT REPLACE ALL THE FUEL INJECTIONS AT ONCE. ONLY WHEN THERE IS A PROBLEM. I ASKED THEM WHY THE COMPUTER SAID EVERYTHING WAS OK AND THEN ENDED UP WITH THE FUEL INJECTOR PROBLEMS. THEY DIDNT HAVE AN ANSWER. FURTHER MORE THE OTHER FUEL INJECTORS CAN GO OUT AT ANY GIVEN TIME. HOPE IM NOT IN THE MOUNTAINS WHEN THAT HAPPENS.*CW
NHTSA ODI #10302496
43,000 miles · Jan 15, 2010
Fuel System, Gasoline
MY 2005 F-150 LARIAT FORD PICKUP TRUCK SUDDENLY BEGAN TO SURGE AS I WAS PULLING INTO MY DRIVEWAY. WHITE SMOKE WAS BILLOWING OUT THE TAIL PIPE. I WAS ABLE TO COMPLETE PARKING OF THE VEHICLE. I TURNED OFF THE ENGINE AND THEN TRIED RESTARTING BUT IT WOULD NOT START. I CALLED A NEARBY FORD DEALER AND THEY DISPATCHED A WRECKER T…
Read full complaint
MY 2005 F-150 LARIAT FORD PICKUP TRUCK SUDDENLY BEGAN TO SURGE AS I WAS PULLING INTO MY DRIVEWAY. WHITE SMOKE WAS BILLOWING OUT THE TAIL PIPE. I WAS ABLE TO COMPLETE PARKING OF THE VEHICLE. I TURNED OFF THE ENGINE AND THEN TRIED RESTARTING BUT IT WOULD NOT START. I CALLED A NEARBY FORD DEALER AND THEY DISPATCHED A WRECKER TO BRING THE TRUCK TO THE FORD DEALER GARAGE LOCATED A FEW MILES AWAY. ONCE THE TRUCK WAS LOOKED AT THE DEALER CALLED TO INFORM ME THAT A FUEL INJECTOR HAD GONE BAD AND THAT FORD WAS AWARE OF THE PROBLEM AND HAD EXTENDED THE WARRANTY ON THIS MODEL YEAR OF PICKUP TRUCK TO 111,000 MILES. THE TRUCK WAS OUT OF THE 35,000 MILES WARRANTY. FORD SAID THERE WOULD BE NO CHARGE TO REPAIR THE INJECTOR. I'M WONDERING WHY THERE WAS NO RECALL BY FORD SINCE THEY ADMIT THEY ARE AWARE OF THE PROBLEM. SHOULD THE INJECTOR HAVE FAILED WHILE DRIVING AT A HIGHER SPEED THERE COULD HAVE BEEN AN ACCIDENT AND POSSIBLE LOSS OF LIFE. *TR
NHTSA ODI #10299909
80,000 miles · Jan 3, 2010
Fuel System, Gasoline
DRIVING HOME @ (HIGHWAY SPEED 55+) FROM A FAMILY GATHERING. SERVICE ENGINE LIGHT ILLUMINATED. ENGINE LOST POWER. I TRIED TO ACCELERATE. NO THROTTLE RESPONSE. ENGINE STALLED. HAD TO FIND PLACE TO PULL OVER WITH NO POWER STEERING. RETURNED GEAR SELECTOR TO P. TURNED IGNITION TO OFF POSITION. RESTARTED AND COMPLETED TRIP. 50…
Read full complaint
DRIVING HOME @ (HIGHWAY SPEED 55+) FROM A FAMILY GATHERING. SERVICE ENGINE LIGHT ILLUMINATED. ENGINE LOST POWER. I TRIED TO ACCELERATE. NO THROTTLE RESPONSE. ENGINE STALLED. HAD TO FIND PLACE TO PULL OVER WITH NO POWER STEERING. RETURNED GEAR SELECTOR TO P. TURNED IGNITION TO OFF POSITION. RESTARTED AND COMPLETED TRIP. 50+ MILES. THIS EVENT HAS OCCURRED TWO TIMES. I HAVE BEEN VERY LUCKY THAT I HAD A PLACE TO PULL OVER AND RESTART THE VEHICLE. IF I HAD BEEN ENTERING OR DRIVING IN HIGH SPEED TRAFFIC THIS FAILURE COULD HAVE CAUSED A MAJOR ACCIDENT. I READ DISCUSSIONS ON 2005 F150 WEB SITE THAT RELATE TO THIS TYPE FAILURE. SCANNED FOR ENGINE CODES. TPS FAULT CODE. REPLACE THROTTLE BODY. I WILL RETAIN OLD PARTS. *TR
NHTSA ODI #10297857
48,000 miles · Sep 3, 2009
Fuel System, Gasoline
SINCE JUNE OF 2009, MY 2005 FORD F-150 SUPERCREW HAS, WITHOUT ANY WARNING, EITHER LOST ALL POWER OR THE ENGINE WAS REDUCED TO IDLE RPM AT HIGHWAY SPEEDS THREE TIMES. EACH TIME, I WAS IN RUSH-HOUR TRAFFIC AND HAD TO MANEUVER ACROSS BUSY LANES WHILE COASTING. IN THE TWO INCIDENTS IN WHICH THE ENGINE STALLED, I HAD TO ACCOMPLISH…
Read full complaint
SINCE JUNE OF 2009, MY 2005 FORD F-150 SUPERCREW HAS, WITHOUT ANY WARNING, EITHER LOST ALL POWER OR THE ENGINE WAS REDUCED TO IDLE RPM AT HIGHWAY SPEEDS THREE TIMES. EACH TIME, I WAS IN RUSH-HOUR TRAFFIC AND HAD TO MANEUVER ACROSS BUSY LANES WHILE COASTING. IN THE TWO INCIDENTS IN WHICH THE ENGINE STALLED, I HAD TO ACCOMPLISH THIS WITHOUT POWER STEERING OR BRAKES. IN THE THIRD INCIDENT, THE ENGINE WAS IDLING SO P/S AND P/B WERE FUNCTIONING, BUT THERE WAS NO RESPONSE TO THROTTLE INPUTS FOR ACCELERATION. THE CHECK ENGINE AND "WRENCH" WARNING LIGHTS WERE ILLUMINATED ON THE DASHBOARD. AFTER TURNING OFF THE IGNITION SWITCH FOR SEVERAL SECONDS, THE VEHICLE RE-STARTED AND WAS ABLE TO ACCELERATE NORMALLY, BUT THE CHECK ENGINE LIGHT REMAINED ILLUMINATED FOR SEVERAL DAYS (THE "WRENCH" LIGHT WENT OFF AFTER RE-START). I WAS FORTUNATE IN THAT I AM A VERY CONFIDENT DRIVER AND WAS ABLE TO QUICKLY ASSESS THE SITUATION AND REACT PROPERLY TO GET SAFELY TO THE SIDE OF THE ROAD. IF MY WIFE HAD BEEN DRIVING THE VEHICLE, I FEAR THAT SHE WOULD NOT HAVE BEEN SO LUCKY. IN DOING RESEARCH ON THIS PROBLEM ON THE INTERNET, IT APPEARS TO BE WIDE SPREAD OVER MULTIPLE VEHICLES (F-150, EXPEDITION, ETC.) MANUFACTURED IN THE 04-05 TIME FRAME. AS THIS PROBLEM IS INTERMITTENT AND COMES WITH ABSOLUTELY NO WARNING, IT IS CLEARLY A SAFETY ISSUE FOR DRIVERS OF THESE FORD VEHICLES. I HAVE CHECKED MY VIN ON THE FORD WEBSITE, AND THERE HAS BEEN NO RECALL ISSUED. PLEASE HELP! *TR
NHTSA ODI #10282734
73,000 miles · May 1, 2009
Fuel System, GasolineFire
TL*THE CONTACT OWNS A 2005 FORD F-150. THE CONTACT NOTICED WHITE SMOKE COMING FROM THE EXHAUST. THE VEHICLE WAS TOWED TO THE DEALER AND THEY STATED THAT THE FUEL INJECTORS FAILED, THUS CAUSING THE ENGINE TO FAIL. THE COST TO REPLACE THE COMPONENT WOULD BE APPROXIMATELY $7,300. THE MANUFACTURER STATED THAT THERE WAS AN INITIA…
Read full complaint
TL*THE CONTACT OWNS A 2005 FORD F-150. THE CONTACT NOTICED WHITE SMOKE COMING FROM THE EXHAUST. THE VEHICLE WAS TOWED TO THE DEALER AND THEY STATED THAT THE FUEL INJECTORS FAILED, THUS CAUSING THE ENGINE TO FAIL. THE COST TO REPLACE THE COMPONENT WOULD BE APPROXIMATELY $7,300. THE MANUFACTURER STATED THAT THERE WAS AN INITIATIVE THAT WOULD EXTEND THE WARRANTY ON THE FUEL INJECTORS. THE CONTACT IS WAITING ON A DECISION ON WHETHER THE MANUFACTURER WILL ASSUME FINANCIAL RESPONSIBILITY. THE FAILURE AND CURRENT MILEAGES WERE 73,000.
NHTSA ODI #10267452
47,000 miles · Apr 1, 2009
Fuel System, GasolineFire
TL*THE CONTACT OWNS A 2005 FORD F-150. WHILE DRIVING APPROXIMATELY 35 MPH ON NORMAL ROAD CONDITIONS, THE BED AND CAB COMPARTMENTS OF THE VEHICLE BURST INTO FLAMES. THE CONTACT WAS NOTIFIED BY ANOTHER MOTORIST. HE IMMEDIATELY TURNED OFF THE ENGINE AND EXITED THE VEHICLE. HE NOTICED FUEL LEAKING FROM THE VEHICLE ONTO THE ROADW…
Read full complaint
TL*THE CONTACT OWNS A 2005 FORD F-150. WHILE DRIVING APPROXIMATELY 35 MPH ON NORMAL ROAD CONDITIONS, THE BED AND CAB COMPARTMENTS OF THE VEHICLE BURST INTO FLAMES. THE CONTACT WAS NOTIFIED BY ANOTHER MOTORIST. HE IMMEDIATELY TURNED OFF THE ENGINE AND EXITED THE VEHICLE. HE NOTICED FUEL LEAKING FROM THE VEHICLE ONTO THE ROADWAY, WHICH ALSO CAUGHT FIRE. THE VEHICLE BECAME ENGULFED IN FLAMES AND WAS DESTROYED. THERE WERE NO WARNINGS PRIOR TO THE FIRE. THE FIRE AND POLICE DEPARTMENTS WERE CALLED TO THE SCENE AND A REPORT WAS FILED. THE FIRE DEPARTMENT STATED THAT THE FIRE ORIGINATED ON THE TOP SURFACE OF THE FUEL TANK. THERE WERE NO PERSONAL INJURIES OR PROPERTY DAMAGE. THE VEHICLE WAS TOWED TO A COLLISION CENTER. THE MANUFACTURER WAS NOTIFIED OF THE MALFUNCTION AND THE INSURANCE COMPANY HAS NOT DETERMINED THE CAUSE OF THE FAILURE. THE FAILURE AND CURRENT MILEAGES WERE 47,000.
NHTSA ODI #10263864
68,200 miles · Oct 14, 2008
Fuel System, Gasoline
WHILE DRIVING INTO TOWN I DECELERATED AND THE ENGINE STALLED. I PUT TRUCK IN NEUTRAL AND REFIRED THE ENGINE. AFTER THAT THE EMISSIONS LIGHT WAS ON. TOOK TRUCK TO MECHANIC AND SAID THE THROTTLE BODY FAILED. MECHANIC REPLACED THROTTLE BODY AND IT COST 450$ PARTS AND LABOR. *TR
NHTSA ODI #10245432
102,000 miles · Aug 22, 2008
Engine And Engine CoolingFuel System, Gasoline
2005 FORD F-150 5.4 LITER ENGINE; ALL SERVICE WORK WAS PERFORMED AT THE RECOMMENDED SERVICE INTERVALS ON THIS VEHICLE. AT 102,000 MILES, I TOOK THE VEHICLE TO THE DEALERSHIP TO HAVE SPARK PLUGS REPLACED. (FORD RECOMMENDED 100,000 MILE TUNE-UP) THE FIRST THREE SPARK PLUGS ATTEMPTED TO BE REMOVED BY THREE DIFFERENT TECHNICIANS BR…
Read full complaint
2005 FORD F-150 5.4 LITER ENGINE; ALL SERVICE WORK WAS PERFORMED AT THE RECOMMENDED SERVICE INTERVALS ON THIS VEHICLE. AT 102,000 MILES, I TOOK THE VEHICLE TO THE DEALERSHIP TO HAVE SPARK PLUGS REPLACED. (FORD RECOMMENDED 100,000 MILE TUNE-UP) THE FIRST THREE SPARK PLUGS ATTEMPTED TO BE REMOVED BY THREE DIFFERENT TECHNICIANS BROKE OFF EVEN WHEN FOLLOWING THE FORD TSB PROCEEDURE. THIS TUNE UP WILL COST ME ALMOST $2,000 DUE TO THE DEFECTIVE SPARK PLUG DESIGN. FORD WILL NOT HELP WITH THE REPAIR. *TR
NHTSA ODI #10239403
40,000 miles · Aug 3, 2008
Electrical SystemEngine And Engine CoolingFuel System, Gasoline
MY TRUCK HAS 56K ON IT BOUGHT IT USED WITH 35K ON IT WHEN IT STARTS RUNS WITH HIGH IDLE AND THE TOP END TICKS REALLY BAD THE TICKING DOES NOT GO AWAY AT ALL SPEEDS AT A STOP LIGHT IT SOUNDS LIKE A DIESEL TIC TIC TIC SOUNDS LIKE A LIFTER IS STUCK. I PUT "LUCAS" IN IT TO TRY TO MAKE IT GO AWAY …
Read full complaint
MY TRUCK HAS 56K ON IT BOUGHT IT USED WITH 35K ON IT WHEN IT STARTS RUNS WITH HIGH IDLE AND THE TOP END TICKS REALLY BAD THE TICKING DOES NOT GO AWAY AT ALL SPEEDS AT A STOP LIGHT IT SOUNDS LIKE A DIESEL TIC TIC TIC SOUNDS LIKE A LIFTER IS STUCK. I PUT "LUCAS" IN IT TO TRY TO MAKE IT GO AWAY THEN I CHANGED THE OIL RAN ABOUT TWO WEEKS WITH NO DIFFERENCE AND CHANGED IT AGAIN AND NO CHANGE CALLED FORD DEALER THEY COULDN'T HELP THEY SAID I WOULD HAVE TAKE IT IN AND GET CHARGED $165. THEN I CHANGED THE SPARK PLUGS MAYBE A FOULED PLUG THAT WASN'T IT THERE GOES 120 BUCKS A COUPLE OF WEEKS AGO MY WIFE WAS DRIVING ON THE FREEWAY AND THE DRIVERS SIDE WINDOW FALLS THE WINDOW REGULATOR BROKE $140 REPLACED THAT ALREADY. THE PASSENGER SEAT BELT LOCKS UP SOMETIMES NOW TO THE FRONT THE STEERING WHEEL SHAKES REALLY BAD WHEN YOU APPLY THE BRAKES TURNED THE ROTORS AT NAPA $20 NEW BRAKE PADS $90 AT KRAGENS BALANCED TIRES FREE I WORK AT A TIRE SHOP SHAKING WENT AWAY FOR ABOUT THREE DAYS 350 MILES LATER THE SHAKING IS BACK WITH A VENGEANCE CHECKED THE BALANCING ON THE TIRES THEY WERE GOOD ROTORS ARE OUT OF SHAPE AGAIN STILL ON THERE NOW AND THE SHAKING IS GETTING WORSE I CANT AFFORD THEM RIGHT NOW SO THEY WILL STAY THERE HOOKED UP THE SNAP ON EHTOS COMPUTER TO IT AND REGISTERS THAT TWO SENSORS HAVE AN OPEN CIRCUIT BUT NO EXPLANATION FOR TOP END NOISE INJECTORS MIGHT BE BAD. *TR
NHTSA ODI #10236779
38,000 miles · Feb 6, 2008
Fuel System, Gasoline
VEHICLE FUEL INJECTORS FILLED ENGINE WITH GASOLINE AND CAUSED MOTOR AND OXYGEN SENSORS TO FAIL. FORD MOTOR COMPANY HAS IDENTIFIED THE PROBLEM BUT IS REFUSING TO FIX INJECTORS UNTIL THEY FAIL. *TR
NHTSA ODI #10217308
Official recalls
3Feb 23, 2011
FORD IS RECALLING CERTAIN MODEL YEAR 2004-2006 F-150 PICK UP TRUCKS AS WELL AS CERTAIN MODEL YEAR 2006 LINCOLN MARK LT VEHICLES. IF THE CLOCKSPRING JUMPER WIRE COMES IN CONTACT WITH THE DRIVER SIDE FRONTAL AIR BAG LOWER HORN PLATE, THE WIRE INSULATION MAY BECOME CHAFED, CREATING A POTENTIAL FOR A SHORT CIRCUIT. IF THIS OCCURS THE AIR BAG WARNING LAMP MAY ILLUMINATE INDICATING THAT SERVICE IS REQUIRED.
Consequence & remedy
Consequence: THE DRIVER SIDE FRONTAL AIR BAG COULD INADVERTENTLY DEPLOY INCREASING THE RISK OF INJURY OR LOSS OF VEHICLE CONTROL IF OCCURRING WHILE IN MOTION.
Remedy: FORD WILL NOTIFY OWNERS AND INSTRUCT THEM TO TAKE THEIR VEHICLES TO A FORD OR LINCOLN/MERCURY DEALER TO HAVE A NEW CLOCKSPRING JUMPER WIRE INSTALLED THAT INCORPORATES A PROTECTIVE MESH COVER. REPAIRS WILL BE PERFORMED FREE OF CHARGE. THIS SAFETY RECALL BEGAN ON SOME VEHICLES IN MARCH 2011. THE RECALL CAMPAIGN ON THE EXPANDED POPULATION IS EXPECTED TO BEGIN ON OR ABOUT MAY 9, 2011. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
May 7, 2008
FORD IS RECALLING 605,684 MY 2005-2006 F-150 AND LINCOLN MARK LT VEHICLES EQUIPPED WITH 5.4L 3-VALVE ENGINES. THE BRAKE BOOSTER VACUUM SUPPLY HOSE ATTACHED TO THE INTAKE MANIFOLD FITTING MAY SWELL OVER TIME AND LOSE RETENTION FORCE. THIS CONDITION COULD ALLOW THE HOSE TO BECOME DETACHED FROM THE FITTING DURING AN INTAKE MANIFOLD BACKFIRE. SHOULD THE HOSE DETACH FROM THE INTAKE MANIFOLD, SEVERAL BRAKE APPLICATIONS WITH POWER ASSIST WILL BE AVAILABLE BEFORE THE VACUUM RESERVE IS DEPLETED.
Consequence & remedy
Consequence: ONCE THE BRAKE BOOSTER VACUUM RESERVE IS DEPLETED, THE DRIVER WILL HAVE FOUNDATION BRAKE FUNCTION, BUT WITH INCREASED BRAKE PEDAL EFFORT. REDUCED VEHICLE BRAKING COULD LEAD TO A CRASH.
Remedy: DEALERS WILL REPLACE A RUBBER HOSE ON THE BRAKE BOOSTER VACUUM SUPPLY TUBE ASSEMBLY. THE RECALL BEGAN ON JUNE 27, 2008. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
Feb 6, 2006
CERTAIN PICKUP TRUCKS FAIL TO COMPLY WITH EITHER THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 105, 'HYDRAULIC AND ELECTRIC BRAKE SYSTEMS' OR FMVSS NO. 135, 'PASSENGER CAR BRAKE SYSTEMS.' THESE VEHICLES WERE BUILT WITH A SOFTWARE ERROR IN THE INSTRUMENT CLUSTER.
Consequence & remedy
Consequence: THIS ERROR COULD PREVENT THE ANTILOCK BRAKE SYSTEM (ABS) WARNING LIGHT FROM ILLUMINATING IF THE ABS MODULE EVER BECAME INOPERATIVE.
Remedy: DEALERS WILL RECALIBRATE THE INSTRUMENT CLUSTER IN THESE VEHICLES. THE RECALL BEGAN ON FEBRUARY 27, 2006. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3EA10001 · Inadvertent Airbag Deployment
Opened Jan 13, 2010 · Closed Apr 25, 2011
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:sensor/control MODULE-INACTIVE
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Additional source detail variants (4)
Air Bags
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal:driver Side:inflator Module
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal:sensor/control MODULE-INACTIVE
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
PE09046 · Inadvertent Airbag Deployment
Opened Sep 24, 2009 · Closed Jan 19, 2010
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:sensor/control MODULE-INACTIVE
FORD REPORTS THAT THE INADVERTENT AIRBAG DEPLOYMENTS ARE MOST LIKELY CAUSED BY THE AIRBAG HORN MOUNTING PLATE'S SHARP METAL EDGE THAT EVENTUALLY CAN CHAFE/CUT THE AIRBAG CLOCKSPRING JUMPER WIRE LEADING TO A SHORT-TO-GROUND CONDITION.ONE HUNDRED EIGHTY TWO (182) OF THE 230 REPORTS WERE FOR AIRBAG DEPLOYMENTS RESULTING IN 56 INJURIES WITH REMAINING 48 REPORTS FOR AN AIRBAG LIGHT ILLUMINATION CONDITION.INJURIES INCLUDE ABRASION, CONTUSION AND CUTS TO THE ARM/HAND/FACE AND/OR UPPER BODY REGIONS.ONE OWNER REPORTED A BROKEN TOOTH AND TWO OWNERS REPORTED BEING KNOCKED UNCONSCIOUS AS A RESULT OF THE AIRBAG DEPLOYMENT.IN ADDITION, MY2004 AND MY2006 F-150 VEHICLES ALSO CONTAIN THE SAME DESIGN THAT RESULTED IN AN ADDITIONAL 89 REPORTS WITH 37 AIRBAG DEPLOYMENTS AND NINE INJURIES. FORD MADE AN INTERIM DESIGN CHANGE TO THE HORN MOUNTING PLATE IN JANUARY 2006 AND THEN MAJOR CHANGES TO THE HORN MOUNTING PLATE, AIRBAG MODULE AND CLOCKSPRING JUMPER WIRE DESIGNS IN JUNE 2006 FOR THE MY2007 VEHICLES.THIS PRELIMINARY EVALUATION IS UPGRADED TO AN ENGINEERING ANALYSIS (EA10-001) TO INCLUDE MY2004-2006 F-150 VEHICLES AND TO FURTHER EVALUATE THE CONDITION.
Additional source detail variants (4)
Air Bags
FORD REPORTS THAT THE INADVERTENT AIRBAG DEPLOYMENTS ARE MOST LIKELY CAUSED BY THE AIRBAG HORN MOUNTING PLATE'S SHARP METAL EDGE THAT EVENTUALLY CAN CHAFE/CUT THE AIRBAG CLOCKSPRING JUMPER WIRE LEADING TO A SHORT-TO-GROUND CONDITION.ONE HUNDRED EIGHTY TWO (182) OF THE 230 REPORTS WERE FOR AIRBAG DEPLOYMENTS RESULTING IN 56 INJURIES WITH REMAINING 48 REPORTS FOR AN AIRBAG LIGHT ILLUMINATION CONDITION.INJURIES INCLUDE ABRASION, CONTUSION AND CUTS TO THE ARM/HAND/FACE AND/OR UPPER BODY REGIONS.ONE OWNER REPORTED A BROKEN TOOTH AND TWO OWNERS REPORTED BEING KNOCKED UNCONSCIOUS AS A RESULT OF THE AIRBAG DEPLOYMENT.IN ADDITION, MY2004 AND MY2006 F-150 VEHICLES ALSO CONTAIN THE SAME DESIGN THAT RESULTED IN AN ADDITIONAL 89 REPORTS WITH 37 AIRBAG DEPLOYMENTS AND NINE INJURIES. FORD MADE AN INTERIM DESIGN CHANGE TO THE HORN MOUNTING PLATE IN JANUARY 2006 AND THEN MAJOR CHANGES TO THE HORN MOUNTING PLATE, AIRBAG MODULE AND CLOCKSPRING JUMPER WIRE DESIGNS IN JUNE 2006 FOR THE MY2007 VEHICLES.THIS PRELIMINARY EVALUATION IS UPGRADED TO AN ENGINEERING ANALYSIS (EA10-001) TO INCLUDE MY2004-2006 F-150 VEHICLES AND TO FURTHER EVALUATE THE CONDITION.
Air Bags:frontal:driver Side:inflator Module
FORD REPORTS THAT THE INADVERTENT AIRBAG DEPLOYMENTS ARE MOST LIKELY CAUSED BY THE AIRBAG HORN MOUNTING PLATE'S SHARP METAL EDGE THAT EVENTUALLY CAN CHAFE/CUT THE AIRBAG CLOCKSPRING JUMPER WIRE LEADING TO A SHORT-TO-GROUND CONDITION.ONE HUNDRED EIGHTY TWO (182) OF THE 230 REPORTS WERE FOR AIRBAG DEPLOYMENTS RESULTING IN 56 INJURIES WITH REMAINING 48 REPORTS FOR AN AIRBAG LIGHT ILLUMINATION CONDITION.INJURIES INCLUDE ABRASION, CONTUSION AND CUTS TO THE ARM/HAND/FACE AND/OR UPPER BODY REGIONS.ONE OWNER REPORTED A BROKEN TOOTH AND TWO OWNERS REPORTED BEING KNOCKED UNCONSCIOUS AS A RESULT OF THE AIRBAG DEPLOYMENT.IN ADDITION, MY2004 AND MY2006 F-150 VEHICLES ALSO CONTAIN THE SAME DESIGN THAT RESULTED IN AN ADDITIONAL 89 REPORTS WITH 37 AIRBAG DEPLOYMENTS AND NINE INJURIES. FORD MADE AN INTERIM DESIGN CHANGE TO THE HORN MOUNTING PLATE IN JANUARY 2006 AND THEN MAJOR CHANGES TO THE HORN MOUNTING PLATE, AIRBAG MODULE AND CLOCKSPRING JUMPER WIRE DESIGNS IN JUNE 2006 FOR THE MY2007 VEHICLES.THIS PRELIMINARY EVALUATION IS UPGRADED TO AN ENGINEERING ANALYSIS (EA10-001) TO INCLUDE MY2004-2006 F-150 VEHICLES AND TO FURTHER EVALUATE THE CONDITION.
Air Bags:frontal
FORD REPORTS THAT THE INADVERTENT AIRBAG DEPLOYMENTS ARE MOST LIKELY CAUSED BY THE AIRBAG HORN MOUNTING PLATE'S SHARP METAL EDGE THAT EVENTUALLY CAN CHAFE/CUT THE AIRBAG CLOCKSPRING JUMPER WIRE LEADING TO A SHORT-TO-GROUND CONDITION.ONE HUNDRED EIGHTY TWO (182) OF THE 230 REPORTS WERE FOR AIRBAG DEPLOYMENTS RESULTING IN 56 INJURIES WITH REMAINING 48 REPORTS FOR AN AIRBAG LIGHT ILLUMINATION CONDITION.INJURIES INCLUDE ABRASION, CONTUSION AND CUTS TO THE ARM/HAND/FACE AND/OR UPPER BODY REGIONS.ONE OWNER REPORTED A BROKEN TOOTH AND TWO OWNERS REPORTED BEING KNOCKED UNCONSCIOUS AS A RESULT OF THE AIRBAG DEPLOYMENT.IN ADDITION, MY2004 AND MY2006 F-150 VEHICLES ALSO CONTAIN THE SAME DESIGN THAT RESULTED IN AN ADDITIONAL 89 REPORTS WITH 37 AIRBAG DEPLOYMENTS AND NINE INJURIES. FORD MADE AN INTERIM DESIGN CHANGE TO THE HORN MOUNTING PLATE IN JANUARY 2006 AND THEN MAJOR CHANGES TO THE HORN MOUNTING PLATE, AIRBAG MODULE AND CLOCKSPRING JUMPER WIRE DESIGNS IN JUNE 2006 FOR THE MY2007 VEHICLES.THIS PRELIMINARY EVALUATION IS UPGRADED TO AN ENGINEERING ANALYSIS (EA10-001) TO INCLUDE MY2004-2006 F-150 VEHICLES AND TO FURTHER EVALUATE THE CONDITION.
Air Bags:frontal:sensor/control MODULE-INACTIVE
FORD REPORTS THAT THE INADVERTENT AIRBAG DEPLOYMENTS ARE MOST LIKELY CAUSED BY THE AIRBAG HORN MOUNTING PLATE'S SHARP METAL EDGE THAT EVENTUALLY CAN CHAFE/CUT THE AIRBAG CLOCKSPRING JUMPER WIRE LEADING TO A SHORT-TO-GROUND CONDITION.ONE HUNDRED EIGHTY TWO (182) OF THE 230 REPORTS WERE FOR AIRBAG DEPLOYMENTS RESULTING IN 56 INJURIES WITH REMAINING 48 REPORTS FOR AN AIRBAG LIGHT ILLUMINATION CONDITION.INJURIES INCLUDE ABRASION, CONTUSION AND CUTS TO THE ARM/HAND/FACE AND/OR UPPER BODY REGIONS.ONE OWNER REPORTED A BROKEN TOOTH AND TWO OWNERS REPORTED BEING KNOCKED UNCONSCIOUS AS A RESULT OF THE AIRBAG DEPLOYMENT.IN ADDITION, MY2004 AND MY2006 F-150 VEHICLES ALSO CONTAIN THE SAME DESIGN THAT RESULTED IN AN ADDITIONAL 89 REPORTS WITH 37 AIRBAG DEPLOYMENTS AND NINE INJURIES. FORD MADE AN INTERIM DESIGN CHANGE TO THE HORN MOUNTING PLATE IN JANUARY 2006 AND THEN MAJOR CHANGES TO THE HORN MOUNTING PLATE, AIRBAG MODULE AND CLOCKSPRING JUMPER WIRE DESIGNS IN JUNE 2006 FOR THE MY2007 VEHICLES.THIS PRELIMINARY EVALUATION IS UPGRADED TO AN ENGINEERING ANALYSIS (EA10-001) TO INCLUDE MY2004-2006 F-150 VEHICLES AND TO FURTHER EVALUATE THE CONDITION.
PE08001 · Loss Of Brake POWER-ASSIST
Opened Jan 8, 2008 · Closed May 9, 2008
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist; Service Brakes, Hydraulic:power Assist:vacuum; Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Additional source detail variants (3)
Service Brakes, Hydraulic:power Assist
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Service Brakes, Hydraulic:power Assist:vacuum
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Illustration