NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
1,316 reports60,000 miles · Oct 23, 2015
Steering
TL* THE CONTACT OWNS A 2011 FORD ESCAPE. WHILE DRIVING AT VARIOUS SPEEDS, EXCESSIVE FORCE WAS REQUIRED TO MANEUVER THE STEERING WHEEL. THE VEHICLE WAS TOWED TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE STEERING TORQUE SENSOR FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE VIN WAS NOT INCLUDED IN NHTSA CAMPAI…
Read full complaint
TL* THE CONTACT OWNS A 2011 FORD ESCAPE. WHILE DRIVING AT VARIOUS SPEEDS, EXCESSIVE FORCE WAS REQUIRED TO MANEUVER THE STEERING WHEEL. THE VEHICLE WAS TOWED TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE STEERING TORQUE SENSOR FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE VIN WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 14V284000 (STEERING). THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 60,000.
NHTSA ODI #10785550
62,523 miles · Oct 21, 2015
EnginePower Train
I WAS DRIVING ALONG THE HIGHWAY AND MY RIDE SHUDDERED SOME AND LOST ACCELERATION, MY ENGINE LIGHT CAME ON THEN THE WRENCH SYMBOL CAME ON AND IT HAS STAYED ON. IT'S GIVING A THROTTLE/ POWERTRAIN ERROR. I'VE DONE SOME RESEARCH AND I'VE SEEN A LOT OF COMPLAINTS CONCERNING THIS ISSUE AND WAS TOLD TO FILE A COMPLAINT. FORD NEEDS TO I…
Read full complaint
I WAS DRIVING ALONG THE HIGHWAY AND MY RIDE SHUDDERED SOME AND LOST ACCELERATION, MY ENGINE LIGHT CAME ON THEN THE WRENCH SYMBOL CAME ON AND IT HAS STAYED ON. IT'S GIVING A THROTTLE/ POWERTRAIN ERROR. I'VE DONE SOME RESEARCH AND I'VE SEEN A LOT OF COMPLAINTS CONCERNING THIS ISSUE AND WAS TOLD TO FILE A COMPLAINT. FORD NEEDS TO ISSUE A RECALL ON THIS PROBLEM BEFORE SOMEONE GETS SERIOUSLY HURT OR KILLED.
NHTSA ODI #10785229
57,000 miles · Sep 28, 2015
Steering
THE POWER STEERING SUDDENLY DIDN'T WORK. UPON SEVERAL RESTARTS, IT BEGAN WORKING AGAIN BUT SOMETIMES STOPS WORKING WHILE THE CAR IS MOVING. THIS EVENT HAS BEEN REPEATED SEVERAL TIMES. THERE IS A RECALL FOR 2008 - 2011 FORD ESCAPES BUT MINE WAS NOT INCLUDED IN THE RECALL BUT HAS THE SAME DANGEROUS PROBLEM AS THE CARS THAT WERE…
Read full complaint
THE POWER STEERING SUDDENLY DIDN'T WORK. UPON SEVERAL RESTARTS, IT BEGAN WORKING AGAIN BUT SOMETIMES STOPS WORKING WHILE THE CAR IS MOVING. THIS EVENT HAS BEEN REPEATED SEVERAL TIMES. THERE IS A RECALL FOR 2008 - 2011 FORD ESCAPES BUT MINE WAS NOT INCLUDED IN THE RECALL BUT HAS THE SAME DANGEROUS PROBLEM AS THE CARS THAT WERE RECALLED. FORD WILL NOT TELL ME WHY MY 2011 WAS EXCLUDED FROM THE RECALL. THE COST OF REPAIR IS APPROXIMATELY $1,000. I DON'T BELIEVE I SHOULD HAVE TO PAY FOR A DANGEROUS DEFECT THAT FORD HAS ACKNOWLEDGED BUT WON'T INCLUDE MY CAR.
NHTSA ODI #10778226
56,000 miles · Sep 25, 2015
Power TrainVehicle Speed Control
WHEN SLOWING DOWN AT ABOUT 20-25 MPH, CAR JERKS LIKE TRANSMISSION IS TRYING TO SLIP FROM 2ND TO 1ST GEAR. HAS BEEN LIKE THIS FOR OVER TWO YEARS. MOST READINGS ON 'NET SUGGESTS SOFTWARE ISSUES BUT NOT MANY OWNERS HAVE FOUND SATISFACTION WITH THE UPDATES AND APPEAR TO HAVE TO PAY FOR THEM..
NHTSA ODI #10777772
52,420 miles · Sep 17, 2015
Electrical SystemVisibility/wiper
A/C PUMP CYCLES ON AND OFF BUT NO A/C IN SUMMER. IN WINTER -THE DEFROSTER CUTS OUT WHICH I BELIEVE IS A OVERHEATING RESISTER THUS NOT CYCLING THE A/C. ALSO SWITCH IS INOP FOR FAN ON POSITIONS 1 AND 2. I BELIEVE THE SYSTEM " MALFUNCTION" IS A FIRE/ SAFETY ISSUE AND NEEDS A SAFETY CAMPAIGN BECAUSE OF ALL WEATHER HAZARDS SUCH AS…
Read full complaint
A/C PUMP CYCLES ON AND OFF BUT NO A/C IN SUMMER. IN WINTER -THE DEFROSTER CUTS OUT WHICH I BELIEVE IS A OVERHEATING RESISTER THUS NOT CYCLING THE A/C. ALSO SWITCH IS INOP FOR FAN ON POSITIONS 1 AND 2. I BELIEVE THE SYSTEM " MALFUNCTION" IS A FIRE/ SAFETY ISSUE AND NEEDS A SAFETY CAMPAIGN BECAUSE OF ALL WEATHER HAZARDS SUCH AS FOG, EXCESSIVE SUMMER TEMPS, AND FREEZING TEMPS WITH CONDENSATION. THANKS
NHTSA ODI #10764961
91,196 miles · Aug 28, 2015
Steering
TL* THE CONTACT OWNS A 2011 FORD ESCAPE. WHILE DRIVING APPROXIMATELY 50 MPH AROUND A CURVE, THE STEERING WHEEL SEIZED WITHOUT WARNING CAUSING THE CONTACT TO DRIVE OFF THE ROAD. THE VEHICLE WAS TOWED TO A DEALER WHERE IT WAS DIAGNOSED THAT THE STEERING GEAR FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUF…
Read full complaint
TL* THE CONTACT OWNS A 2011 FORD ESCAPE. WHILE DRIVING APPROXIMATELY 50 MPH AROUND A CURVE, THE STEERING WHEEL SEIZED WITHOUT WARNING CAUSING THE CONTACT TO DRIVE OFF THE ROAD. THE VEHICLE WAS TOWED TO A DEALER WHERE IT WAS DIAGNOSED THAT THE STEERING GEAR FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND STATED THAT THE VIN WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 14V284000 (STEERING). THE FAILURE MILEAGE WAS APPROXIMATELY 91,196.
NHTSA ODI #10759968
22,000 miles · Aug 27, 2015
Power Train
MY 2011 ESCAPE TRANSMISSION SEEMED TO SHIFT HARD WHEN SLOWING DOWN AT TIMES. THIS WOULD HAPPEN INTERMITTENTLY AND DID NOT CAUSE A LOT OF PROBLEMS WHEN I FIRST GOT IT. IT SEEMED TO OCCUR MORE FREQUENTLY AROUND THE FIRST OF THIS YEAR. I TOOK IT TO A FORD DEALERSHIP (BILL COLLINS FORD) TO CHECK THE TRANSMISSION. THEY KEPT IT FO…
Read full complaint
MY 2011 ESCAPE TRANSMISSION SEEMED TO SHIFT HARD WHEN SLOWING DOWN AT TIMES. THIS WOULD HAPPEN INTERMITTENTLY AND DID NOT CAUSE A LOT OF PROBLEMS WHEN I FIRST GOT IT. IT SEEMED TO OCCUR MORE FREQUENTLY AROUND THE FIRST OF THIS YEAR. I TOOK IT TO A FORD DEALERSHIP (BILL COLLINS FORD) TO CHECK THE TRANSMISSION. THEY KEPT IT FOR SEVERAL DAYS BEFORE THEY EVEN LOOKED AT IT. THE TRANSMISSION NEEDED SOFTWARE UPDATES WHICH I HAD TO PAY ABOUT $160 FOR. I HAD TO TAKE IT BACK AGAIN A FEW MONTHS LATER AND IT WAS THE SAME THING - NEEDED A SOFTWARE UPDATE AFTER THEY KEPT IT SEVERAL DAYS AGAIN. THERE APPEARS TO BE SOME TYPE OF PROBLEM WITH THE TRANSMISSION NEEDING A SOFTWARE UPDATE SO FREQUENTLY.
NHTSA ODI #10759782
81,000 miles · Aug 22, 2015
Engine
WHEN ACCELERATING FROM A STOPPED POSITION, THE VEHICLE FELT AS IF IT WERE ABOUT TO STALL. I PRESSED THE CLUTCH AND THE VEHICLE DID NOT STALL, BUT WOULD NOT MOVE FORWARD. I TURNED THE VEHICLE OFF. I RESTARTED THE VEHICLE (WHICH HESITATED TO CATCH FOR SEVERAL SECONDS). UPON THE VEHICLE STARTING, I AGAIN ATTEMPTED TO ACCELERATE…
Read full complaint
WHEN ACCELERATING FROM A STOPPED POSITION, THE VEHICLE FELT AS IF IT WERE ABOUT TO STALL. I PRESSED THE CLUTCH AND THE VEHICLE DID NOT STALL, BUT WOULD NOT MOVE FORWARD. I TURNED THE VEHICLE OFF. I RESTARTED THE VEHICLE (WHICH HESITATED TO CATCH FOR SEVERAL SECONDS). UPON THE VEHICLE STARTING, I AGAIN ATTEMPTED TO ACCELERATE THROUGH THE INTERSECTION. AT FIRST THE VEHICLE SEEMED OK, BUT SHORTLY THROUGH THE INTERSECTION THE VEHICLE LOST ALL ACCELERATION. I PULLED OFF TO THE SIDE OF THE ROAD AND TURNED THE VEHICLE OFF. AFTER SEVERAL MINUTES I RESTARTED THE VEHICLE AND WAS ABLE TO CONTINUE WITHOUT INCIDENT, HOWEVER THE "CHECK ENGINE" LIGHT WAS ILLUMINATED. I HAD THE VEHICLE CHECKED AND IT READ ERROR CODE P2111. THE CHECK ENGINE LIGHT WENT OUT AND THE VEHICLE DID NOT GIVE ME PROBLEMS AGAIN UNTIL AUGUST 20, 2015. AS I ACCELERATED FROM A STOPPED POSITION, THE VEHICLE AGAIN LOST ALL POWER TO THE ENGINE (THOUGH IT DID NOT STALL). I WAS ABLE TO MOVE TO THE SIDE OF THE ROAD AND DISENGAGE THE ENGINE. AFTER SEVERAL MINUTES, AND WITH A HESITATED "CATCH" THE ENGINE RESTARTED. I BELIEVE THIS IS AN EXISTING AND KNOWN PROBLEM WITH FORD (NHTSA PE13003), HOWEVER, I WAS TOLD BY MY LOCAL DEALER AND FORD CUSTOMER SERVICE THAT THE WARRANTY EXTENSION OFFERED UNDER THAT INVESTIGATION DOES NOT APPLY TO MY VEHICLE (WHICH FALLS WITHIN ALL OF THE GUIDELINES FOR YEAR, MAKE, MODEL, AND MILEAGE).
NHTSA ODI #10758554
61,400 miles · Aug 14, 2015
Power Train
DRIVING CAR HOME AFTER WORK - SLOWED DOWN AND STOPPED AFTER TRAFFIC LIGHT CHANGE. PRESSED ON ACCELERATOR AND CAR SHUDDERED WOULD NOT ACCELERATE. THE WRENCH LIGHT CAME ON AND THE CAR WENT INTO LIMP HOME MODE. TURNED INTO PARKING LOT AND SHUT DOWN AND RESTARTED ENGINE. THE ENGINE RPM SUDDENLY WENT TO ABOUT 7000 RPM WITH THE NO…
Read full complaint
DRIVING CAR HOME AFTER WORK - SLOWED DOWN AND STOPPED AFTER TRAFFIC LIGHT CHANGE. PRESSED ON ACCELERATOR AND CAR SHUDDERED WOULD NOT ACCELERATE. THE WRENCH LIGHT CAME ON AND THE CAR WENT INTO LIMP HOME MODE. TURNED INTO PARKING LOT AND SHUT DOWN AND RESTARTED ENGINE. THE ENGINE RPM SUDDENLY WENT TO ABOUT 7000 RPM WITH THE NO PUSH OF THE ACCELERATOR. ENGINE EVENTUALLY NORMALIZED AND I WAS ABLE TO DRIVE IT THE REST OF THE WAY HOME. MY HUSBAND TEST DROVE THE VEHICLE AND THE SAME THING HAPPENED TO HIM WITH THE CAR GOING NON RESPONSIVE INTO LIMP HOME MODE. HE TROUBLESHOT THE ISSUE TO THE THROTTLE BODY. AFTER REMOVING THE THROTTLE BODY, CLEANING IT, AND RECALIBRATING , THE ISSUE DISAPPEARED. HE IS GOING TO REPLACE THE PART FOR SAFETY SINCE THIS ISSUE HAPPENING AT HIGHWAY SPEED COULD BECOME DANGEROUS.
NHTSA ODI #10748629
89,866 miles · Aug 10, 2015
EngineUnknown Or Other
TODAY WAS THE WORST IT HAS BEEN, IT AL STARTED ABOUT 2 MONTHS AGO, IT JUST HAPPENS WITHOUT WARNING OF ANY KIND. BUT TODAY THE FIRST TIME WAS ON MY WAY TO WORK, LUCKILY I HAD A PLACE TO PULL OFF, TURN OFF ENGINE SIT AND START IT BACK, NOT IMMEDIATE I MAY SAY ( A LITTLE HESITATION IN THE STARTING) THEN THE SECOND TIME (TODAY) HAPP…
Read full complaint
TODAY WAS THE WORST IT HAS BEEN, IT AL STARTED ABOUT 2 MONTHS AGO, IT JUST HAPPENS WITHOUT WARNING OF ANY KIND. BUT TODAY THE FIRST TIME WAS ON MY WAY TO WORK, LUCKILY I HAD A PLACE TO PULL OFF, TURN OFF ENGINE SIT AND START IT BACK, NOT IMMEDIATE I MAY SAY ( A LITTLE HESITATION IN THE STARTING) THEN THE SECOND TIME (TODAY) HAPPENED IN AN INTERSECTION SAME PROCESS, BUT THIS TIME WAS VERY SCARY, SEEING HOW CARS WERE COMING AT ME HONKING AND GOING AROUND ME. THEN THE THIRD TIME (TODAY) WAS ON MY WAY HOME FROM WORK, WITH MY GRANDSON IN THE CAR I MIGHT ADD, THIS ACCRUED NOT 30 MINUTES AFTER THE 2ND INCIDENT. I HAD TO PULL OFF THE ROAD AND REPEAT THE PROCESS TO GET GOING AGAIN. IF THIS CONTINUES TO OCCUR, IT COULD TURN INTO A VERY BAD ACCIDENT.
NHTSA ODI #10747630
Official recalls
2Oct 26, 2016
Ford Motor Company (Ford) is recalling certain model year 2010-2012 Ford Escape vehicles manufactured February 26, 2009, to April 29, 2012, and 2010-2011 Mercury Mariner vehicles manufactured February 25, 2009, to December 12, 2010. On vehicles with a 3.0L engine, the Fuel Delivery Module (FDM) may crack, causing a fuel leak.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy: Ford will notify owners, and dealers will replace the FDM flange with one that has a redesigned fuel supply port, free of charge. Remedy parts are currently unavailable. Interim notices were mailed to owners on December 13, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S41.
May 29, 2014
Ford Motor Company (Ford) is recalling certain model year 2008-2011 Ford Escape and Mercury Mariner vehicles manufactured August 18, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.
Consequence & remedy
Consequence: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will update the software for the power steering control module (PSCM) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the PSCM when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on July 18, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S05.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4DP15001 · Loss Of Power Steering While Driving
Opened Apr 1, 2015 · Closed Jun 14, 2018
Status: closed (inferred from source dates) · Steering:electric Power Assist System
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
DP12006 · Electronic Throttle Body Malfunction
Opened Oct 2, 2012 · Closed Feb 21, 2013
Status: closed (inferred from source dates) · Engine
In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.
PE11016 · Rear Liftgate Window Glass Breakage
Opened Apr 27, 2011 · Closed Aug 18, 2011
Status: closed (inferred from source dates) · Structure:body:hatchback/liftgate; Structure:body:hatchback/liftgate:hinge And Attachments; Structure:body:hatchback/liftgate:support Device/strut; Visibility; Visibility:glass, Side/rear
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (5)
Structure:body:hatchback/liftgate
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:hatchback/liftgate:hinge And Attachments
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:hatchback/liftgate:support Device/strut
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Visibility
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Visibility:glass, Side/rear
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Illustration