NHTSA owner reports · September 18, 2026 snapshot.
Vehicle Speed Control complaints
245 reportsClear category filter37,311 miles · Jul 27, 2013
Fuel/propulsion SystemVehicle Speed Control
DRIVING PA TURNPIKE AT 10:00 PM 7/19/2013 @ 65 MPH SB. HEARD THUMP, WRENCH LITE CAME ON, THEN ENGINE LITE. NO POWER ON ACCELERATION. COASTED TO SIDE OF ROAD. CALLED AAA. COULDN'T START CAR KEPT SPUTTERING. WAITED FOR 1 1/2 HOURS NO AAA. TRIED TO START CAR. STARTED. CONTINUED ON JOURNEY. NEXT DAY TOOK TO DEALER. GOT AN APPOINTMEN…
Read full complaint
DRIVING PA TURNPIKE AT 10:00 PM 7/19/2013 @ 65 MPH SB. HEARD THUMP, WRENCH LITE CAME ON, THEN ENGINE LITE. NO POWER ON ACCELERATION. COASTED TO SIDE OF ROAD. CALLED AAA. COULDN'T START CAR KEPT SPUTTERING. WAITED FOR 1 1/2 HOURS NO AAA. TRIED TO START CAR. STARTED. CONTINUED ON JOURNEY. NEXT DAY TOOK TO DEALER. GOT AN APPOINTMENT FOR 7/23/2013 @ 2PM. DROVE CAR ON MON. 7/22/2013. GOING 35 MPH. SAME THING. THUMP, WRENCH LITE, ENGINE LITE.NO POWER. COASTED TO OFF RAMP. TOOK TO DEALER ON 7/23/2013 FOR DIAGNOSTIC.FAILED THROTTLE BODY ASSY. REMOVED AND REPLACED THROTTLE BODY AND REPROGRAMMED THE PCM AND RETESTED. COST..$500.68...OUT OF WARRANTY. *TR
NHTSA ODI #10532113
46,670 miles · Jul 25, 2013
EngineFuel/propulsion SystemVehicle Speed Control
MY WIFE WAS TAKING HER MOTHER HOME ON THE 18TH OF JULY WHEN THE ESCAPE STARTED TO HESITATE AND SURGE GOING UP A HILL. WHEN SHE PRESSED ON THE GAS PEDAL THERE WAS NO RESPONSE FROM THE ENGINE.THE POWERTRAIN AND ENGINE LIGHTS CAME ON SO SHE CALLED ME IMMEDIATELY. SHE WAS AFRAID TO LEAVE IT RUNNING SO SHE SHUT IT DOWN. WHAT MADE THI…
Read full complaint
MY WIFE WAS TAKING HER MOTHER HOME ON THE 18TH OF JULY WHEN THE ESCAPE STARTED TO HESITATE AND SURGE GOING UP A HILL. WHEN SHE PRESSED ON THE GAS PEDAL THERE WAS NO RESPONSE FROM THE ENGINE.THE POWERTRAIN AND ENGINE LIGHTS CAME ON SO SHE CALLED ME IMMEDIATELY. SHE WAS AFRAID TO LEAVE IT RUNNING SO SHE SHUT IT DOWN. WHAT MADE THINGS WORSE WAS THE FACT THAT IT WAS 97 DEGREES OUT THAT DAY AND SHE HAD HER MOTHER WITH HER WHO IS HANDICAPPED. AFTER THE ENGINE COOLED A BIT, I WAS ABLE TO DRIVE IT THE REST OF THE WAY TO HER MOTHER'S HOUSE. AFTER DROPPING HER OFF, THE VEHICLE BROKE DOWN TWICE ON THE WAY TO THE REPAIR FACILITY. IT TURNED OUT TO BE A PROBLEM WITH THE THROTTLE BODY. AS A FORMER MECHANIC AND NOW A PARTS PERSON I CAN SAY WITH CONFIDENCE THAT THIS IS DEFINITELY A SAFETY ISSUE. *TR
NHTSA ODI #10531896
45,000 miles · Jul 25, 2013
EngineFuel/propulsion SystemPower Train
SMALL SURGES JUST AFTER STOPS. TOTAL LOSS OF POWER AT HIGHWAY SPEEDS. JULY 2012 SHOWED THE CHECK ENGINE LIGHT, AND HAD TO COAST TO SIDE OF THE ROAD, GAS PEDAL TOTALLY DEAD, ENGINE AND CAR STILL RUNNING. TURN OFF AND RESTART AND ALL CHECK ENGINE LIGHTS GO AWAY AND CAR ACTS NORMALLY. DEALERSHIP FOUND NO CODES. JUNE 2013 AGAIN…
Read full complaint
SMALL SURGES JUST AFTER STOPS. TOTAL LOSS OF POWER AT HIGHWAY SPEEDS. JULY 2012 SHOWED THE CHECK ENGINE LIGHT, AND HAD TO COAST TO SIDE OF THE ROAD, GAS PEDAL TOTALLY DEAD, ENGINE AND CAR STILL RUNNING. TURN OFF AND RESTART AND ALL CHECK ENGINE LIGHTS GO AWAY AND CAR ACTS NORMALLY. DEALERSHIP FOUND NO CODES. JUNE 2013 AGAIN TOTAL LOSS OF POWER AT HIGHWAY SPEEDS, THIS TIME POWERTRAIN LIGHT COMES ON, AND THE CAR HAS TO COAST TO THE SIDE OF THE ROAD, GAS PEDAL TOTALLY DEAD, ENGINE AND CAR STILL RUNNING. TURN OFF AND RESTART AND ALL POWERTRAIN LIGHTS GO AWAY AND CAR ACTS NORMALLY. THIS LOSS OF POWER HAS HAPPENED 15-20 TIMES TO DATE FROM JULY 2012 TO JULY 2013. *TR
NHTSA ODI #10531805
38,500 miles · Jul 25, 2013
Electrical SystemFuel/propulsion SystemVehicle Speed Control
ON MAY 23RD WE WERE TRAVELING ON AN INTERSTATE AT ABOUT 65MPH AND SUDDENLY THE CAR LOST ACCELERATION, WE WERE ABLE TO PULL OVER TO SIDE OF ROAD AND LUCKILY ABLE TO AVOID OTHER CARS. WE TURNED OFF ENGINE AND IT STARTED AGAIN BUT WAS VERY APPREHENSIVE. THE CAR DID OK UNTIL JULY 20TH WHEN WE STOPPED AT A LIGHT AND WHEN WE STARTED T…
Read full complaint
ON MAY 23RD WE WERE TRAVELING ON AN INTERSTATE AT ABOUT 65MPH AND SUDDENLY THE CAR LOST ACCELERATION, WE WERE ABLE TO PULL OVER TO SIDE OF ROAD AND LUCKILY ABLE TO AVOID OTHER CARS. WE TURNED OFF ENGINE AND IT STARTED AGAIN BUT WAS VERY APPREHENSIVE. THE CAR DID OK UNTIL JULY 20TH WHEN WE STOPPED AT A LIGHT AND WHEN WE STARTED THE ACCELERATION WAS GONE AGAIN, WE WERE ABLE TO GET TO SIDE OF ROAD BUT IT TOOK 3 TRIES TO GET IT STARTED AGAIN. WE TRIED TO GET HOME BEFORE IT HAPPENED AGAIN BUT ABOUT 2 MILES FROM OUR HOME IT DIED AGAIN. WE WERE ON A 2 LANE ROAD BUT WAS ABLE TO PULL INTO SOMEONE'S DRIVEWAY AND IT TOOK SEVERAL TIMES TO GET IT STARTED AND WE TRIED TO GET BACK ON ROAD BUT IT DIED AGAIN. AFTER A COUPLE MORE TRIES IT STARTED AND WE WERE ABLE TO MAKE IT HOME. WE HAD TO CALL A TOW TRUCK TO TAKE IT TO THE DEALER BECAUSE WE WERE AFRAID IT WOULD HAPPEN AGAIN AND COULD HAVE HAD AN ACCIDENT. WE HAVE ONLY HAD THE CAR FOR 2 YRS AND IT ONLY HAS AROUND 38000 MILES. *TR
NHTSA ODI #10531774
52,000 miles · Jul 24, 2013
Fuel/propulsion SystemVehicle Speed Control
WHEN ACCELERATING THE CAR STALLS FOR NO APPARENT REASON. I WAS DRIVING DOWN A BUSY HIGHWAY IN THE LEFT LANE, WHEN I ACCELERATED THE MADE A COUPLE OF JERKS, THRU THE WRENCH SIGN ON THE DASH AND LOST ALL POWER. THIS HAS HAPPENED TO ME 3 TIMES, ONCE FROM A DEAD STOP TURNING LEFT ACROSS TRAFFIC AND TWICE WHILE ACCELERATING AT AN A…
Read full complaint
WHEN ACCELERATING THE CAR STALLS FOR NO APPARENT REASON. I WAS DRIVING DOWN A BUSY HIGHWAY IN THE LEFT LANE, WHEN I ACCELERATED THE MADE A COUPLE OF JERKS, THRU THE WRENCH SIGN ON THE DASH AND LOST ALL POWER. THIS HAS HAPPENED TO ME 3 TIMES, ONCE FROM A DEAD STOP TURNING LEFT ACROSS TRAFFIC AND TWICE WHILE ACCELERATING AT AN AVERAGE SPEED ON THE HIGHWAY THERE WAS A TOTAL LOSS OF PROPULSION OF THE CAR AND ALL YOU CAN DO IS HOPE AND PRAY YOU CAN COAST TO SAFETY. IT IS JUST A MATTER OF TIME BEFORE SOMEONE IS KILLED ON A BUSY INTERSTATE WHEN THE THROTTLE GOES OUT. FORD REPLACED MY THROTTLE YESTERDAY FOR $328 AND NEVER SAID A WORD ABOUT THIS BEING AN ISSUE WITH THIS CAR! THIS ABSOLUTELY NEEDS TO BE LOOKED AT AND RECALLED! *TR
NHTSA ODI #10531540
59,700 miles · Jul 23, 2013
Electrical SystemEngineVehicle Speed Control
I WAS TRAVELING 60 MPH ON THE HIGHWAY WHEN THE VEHICLE LOST POWER, I HAD TO COAST OVER TO THE SIDE OF THE ROAD, TURN OFF THE VEHICLE AND TURN IT BACK ON. THE VEHICLE WOULD START BUT THEN RETURN TO IDLE WITH NO THROTTLE RESPONSE. THIS WENT ON REPEATEDLY BEFORE I HAD TO HAVE IT TOWED TO A DEALERSHIP. BECAUSE THIS OCCURRED ON A SAT…
Read full complaint
I WAS TRAVELING 60 MPH ON THE HIGHWAY WHEN THE VEHICLE LOST POWER, I HAD TO COAST OVER TO THE SIDE OF THE ROAD, TURN OFF THE VEHICLE AND TURN IT BACK ON. THE VEHICLE WOULD START BUT THEN RETURN TO IDLE WITH NO THROTTLE RESPONSE. THIS WENT ON REPEATEDLY BEFORE I HAD TO HAVE IT TOWED TO A DEALERSHIP. BECAUSE THIS OCCURRED ON A SATURDAY AFTERNOON THE SERVICE DEPARTMENT WAS CLOSED AND I WAS UNABLE TO SPEAK TO ANYONE. FIRST THING MONDAY MORNING WHEN I WENT IN THEY FIRST TOLD ME THEY DID NOT KNOW ABOUT THE PROBLEMS WITH THE THROTTLE CONTROL UNIT. UPON PRESENTING THEM WITH NUMEROUS COPIES OF COMPLAINTS FILED ON LINE THEY FINALLY ACKNOWLEDGED THAT THERE WAS A PROBLEM. HOWEVER WITH NO RECALL I WOULD NEED TO PAY FOR A REPLACEMENT WHICH WITH TOWING RESULTED IN A $550.00 BILL. APPARENTLY I WAS VERY LUCKY THAT THERE WAS ONE REPLACEMENT IN STOCK (HMMM), OTHERWISE IT WOULD BE WEEKS. I HOPE THE REPLACEMENT WORKS BECAUSE IT HAS BEEN A CHRONIC PROBLEM FOR MONTHS. SKEPTICAL TO SAY THE LEAST. *TR
NHTSA ODI #10531522
35,500 miles · Jul 23, 2013
Fuel/propulsion SystemVehicle Speed Control
I WAS DRIVING ON THE HIGHWAY AT ABOUT 60 MPH FOR ABOUT 50 MILES. THE CAR SUDDENLY LOST POWER AND WENT INTO LIMP MODE. THE SMALL TOOL LIGHT CAME ON THE DASH INDICATING THE THROTTLE. I PULLED OFF THE HIGHWAY AND STOPPED. AFTER A FEW MINUTES, I RESTARTED THE CAR, WHICH SEEMED FINE. I DROVE FOR ABOUT 1/2 AN HOUR, AND IT DID TH…
Read full complaint
I WAS DRIVING ON THE HIGHWAY AT ABOUT 60 MPH FOR ABOUT 50 MILES. THE CAR SUDDENLY LOST POWER AND WENT INTO LIMP MODE. THE SMALL TOOL LIGHT CAME ON THE DASH INDICATING THE THROTTLE. I PULLED OFF THE HIGHWAY AND STOPPED. AFTER A FEW MINUTES, I RESTARTED THE CAR, WHICH SEEMED FINE. I DROVE FOR ABOUT 1/2 AN HOUR, AND IT DID THE SAME THING AGAIN. THIS TIME IT WOULD NOT GO MORE THEN 20 MPH. I HAD THE CAR TOWED TO THE CLOSEST FORD DEALERSHIP. THEY SAID THE CODE SHOWED THAT THE ACCELERATOR STUCK. THEY RESET THE CODE AND SAID THEY FOUND NOTHING ELSE WRONG. WHEN I GOT HOME, I CALLED THE DEALERSHIP I HAVE THE CAR SERVICED AT. THEY SAID IT WAS THE THROTTLE BODY ASSEMBLY AND ITS A COMMON PROBLEM. APPARENTLY I HAVE TO HAVE IT HAPPEN AGAIN FOR A REPAIR OR REPLACEMENT TO BE DONE AND IT HAS TO BE TOWED TO THAT PARTICULAR DEALERSHIP. A RECALL WOULD BE GOOD, AS THIS IS VERY DANGEROUS AND I DON'T WANT TO HAVE IT HAPPEN AGAIN SO THAT I CAN GET IT REPAIRED. *TR
NHTSA ODI #10531501
62,000 miles · Jul 23, 2013
EngineVehicle Speed Control
THE ENGINE INTERMITTENTLY STALLED/QUIT WHILE DRIVING AT SPEED ON NUMEROUS OCCASIONS. WE TOOK IT TO A FORD DEALERSHIP. DIAGNOSTICS BY THEIR SERVICE DEPARTMENT IDENTIFIED THE PROBLEM AS A DEFECTIVE THROTTLE BODY. *TR
NHTSA ODI #10526451
53,000 miles · Jul 22, 2013
EnginePower TrainVehicle Speed Control
AFTER TRAVELING FOR A APPROXIMATELY 45 MINUTES, MY CAR STOPPED ACCELERATING DOWN THE ROAD. AT THIS POINT MY GAS PEDAL WOULD NOT MAKE A DIFFERENCE IN RPM OR SPEED, THEN MY ENGINE BEGAN SHAKING VIOLENTLY. I BARELY WAS ABLE TO MAKE IT TO THE SHOULDER OF THE INTERSTATE. THEN, A WRENCH LIGHT CAME ON THE DASH OF MY VEHICLE. I THEN…
Read full complaint
AFTER TRAVELING FOR A APPROXIMATELY 45 MINUTES, MY CAR STOPPED ACCELERATING DOWN THE ROAD. AT THIS POINT MY GAS PEDAL WOULD NOT MAKE A DIFFERENCE IN RPM OR SPEED, THEN MY ENGINE BEGAN SHAKING VIOLENTLY. I BARELY WAS ABLE TO MAKE IT TO THE SHOULDER OF THE INTERSTATE. THEN, A WRENCH LIGHT CAME ON THE DASH OF MY VEHICLE. I THEN TURNED THE IGNITION OFF. UPON RESTARTING THE VEHICLE, THE LIGHT WAS GONE AND THE GAS PEDAL WORKED ONCE MORE. I MERGED INTO TRAFFIC AND CONTINUED ON MY TRIP WITH SLIGHT HESITATION ON THE REMAINDER OF MY TRIP. THIS WHOLE SCENARIO HAPPENED AGAIN ON THE 19TH OF JULY 2013 ONLY 20 MINUTES INTO MY TRIP HOME. VEHICLE IS CURRENTLY AT FORD DEALERSHIP BEING CHECKED OUT. *TR
NHTSA ODI #10526103
44,000 miles · Jul 22, 2013
EngineVehicle Speed Control
I WAS DRIVING ON THE HIGHWAY, GOING ABOUT 70MPH ON CRUISE CONTROL. THE CRUISE CONTROL SUDDENLY DISENGAGED AND THE CAR STARTED SLOWING DOWN, PLUS THE WRENCH MAINTENANCE SIGN IN THE DASHBOARD LIT UP. I HIT THE GAS AND NOTHING WOULD HAPPEN, I BASICALLY PUT THE GAS PEDAL TO THE FLOOR WITH NO RESULTS. I PULLED OVER TO THE SIDE OF THE…
Read full complaint
I WAS DRIVING ON THE HIGHWAY, GOING ABOUT 70MPH ON CRUISE CONTROL. THE CRUISE CONTROL SUDDENLY DISENGAGED AND THE CAR STARTED SLOWING DOWN, PLUS THE WRENCH MAINTENANCE SIGN IN THE DASHBOARD LIT UP. I HIT THE GAS AND NOTHING WOULD HAPPEN, I BASICALLY PUT THE GAS PEDAL TO THE FLOOR WITH NO RESULTS. I PULLED OVER TO THE SIDE OF THE ROAD, AVOIDING TRAFFIC, AND PARKED THE CAR. ONCE THE CAR WAS IN PARK, THE CAR STARTED VIBRATING HEAVILY. I SHUT THE CAR DOWN AND WAITED ABOUT 5-10 MINUTES AND THEN STARTED THE CAR AGAIN, IT TOOK ABOUT 3 TRIES TO GET THE CAR TO START AGAIN. I TOOK THE CAR TO THE MECHANIC, THEY COULD NOT GET THE CAR REPEAT THE FAILS AT THAT TIME, SO THEY COULD NOT DETERMINE WHAT HAPPENED. ABOUT A WEEK LATER, I'M ON THE HIGHWAY HEADED TO WORK AND IT HAPPENS AGAIN, SAME SITUATION, EXCEPT THIS TIME ALL THE LIGHTS IN THE DASHBOARD LIT UP AND I WAS NOT USING CRUISE CONTROL. I TOOK THE CAR BACK TO THE MECHANIC AND HE WORKED ON IT FOR A FEW DAYS, CAME BACK AND SAID THAT THE THROTTLE BODY WAS MALFUNCTIONING AND IT NEEDED TO BE REPLACED. BEFORE I DID THAT, I CALLED THE FORD DEALERSHIP AND EXPLAINED THE SITUATION TO THE LEAD MECHANIC THERE AND WITHOUT EVEN SEEING THE CAR, HE AGREED WITH MY MECHANIC THAT IT 100% SOUNDED LIKE A THROTTLE BODY PROBLEM. SO IT HAS BEEN REPLACED AND I HAVE HAD THE CAR BACK WITH NO PROBLEMS SINCE THEN. *TR
NHTSA ODI #10526059
NHTSA investigations
4DP15001 · Loss Of Power Steering While Driving
Opened Apr 1, 2015 · Closed Jun 14, 2018
Status: closed (inferred from source dates) · Steering:electric Power Assist System
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
DP12006 · Electronic Throttle Body Malfunction
Opened Oct 2, 2012 · Closed Feb 21, 2013
Status: closed (inferred from source dates) · Engine
In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.
PE11016 · Rear Liftgate Window Glass Breakage
Opened Apr 27, 2011 · Closed Aug 18, 2011
Status: closed (inferred from source dates) · Structure:body:hatchback/liftgate; Structure:body:hatchback/liftgate:hinge And Attachments; Structure:body:hatchback/liftgate:support Device/strut; Visibility; Visibility:glass, Side/rear
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (5)
Structure:body:hatchback/liftgate
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:hatchback/liftgate:hinge And Attachments
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:hatchback/liftgate:support Device/strut
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Visibility
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Visibility:glass, Side/rear
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Illustration