NHTSA owner reports · September 18, 2026 snapshot.
Unknown Or Other complaints
56 reportsClear category filter163,000 miles · Jan 11, 2022
Unknown Or Other
The contact owns a 2011 Ford Escape. The contact stated that while driving at various speeds, the power steering assist fault warning message appeared on the instrument panel. The contact took the vehicle to a dealer and was informed that her vehicle was not included in NHTSA Campaign Number: 14V284000 (Steering). The manufactur…
Read full complaint
The contact owns a 2011 Ford Escape. The contact stated that while driving at various speeds, the power steering assist fault warning message appeared on the instrument panel. The contact took the vehicle to a dealer and was informed that her vehicle was not included in NHTSA Campaign Number: 14V284000 (Steering). The manufacturer was also notified of the recall and provided her with the same information as the dealer. The vehicle had yet to be repaired. The failure mileage was approximately 163,000.
NHTSA ODI #11447030
160,000 miles · Jan 11, 2022
Unknown Or Other
The contact owns a 2011 Ford Escape. The contact stated that while driving at various speeds, the power steering would intermittently fail without warning. The contact stated that the power steering functionality would return upon restart of the engine. The contact had spoken to a dealer who informed him that his vehicle was not…
Read full complaint
The contact owns a 2011 Ford Escape. The contact stated that while driving at various speeds, the power steering would intermittently fail without warning. The contact stated that the power steering functionality would return upon restart of the engine. The contact had spoken to a dealer who informed him that his vehicle was not included in NHTSA Campaign Number: 14V284000 (Steering). The contact also spoke to an independent mechanic who was familiar with the failure and informed him that a sensor would need to be replaced. The manufacturer was notified of the failure and promised the contact a call back from a manager however, the contact had not yet heard from a manager. The vehicle had yet to be repaired. The failure mileage was approximately 160,000.
NHTSA ODI #11447001
Mileage unknown · Dec 6, 2021
Unknown Or Other
THE POWER STEERING FAiLED. The torque sensor was diagnosed as failed. Unable to steer the vehicle. Turns out Ford says this car wasn’t reported as faulty. BUT 914,000 OTHER FORDS FROM 2008-2011 WERE RECALLED !!!!!!! This vehicle is the model and year of ALL those recalls.
NHTSA ODI #11442948
Mileage unknown · Nov 17, 2021
Unknown Or Other
The car started shutting off when putting gas and all the ABS lights started turning on. Then it escalated to the car shutting off when pressing the brakes. Now it shuts off randomly never while driving at higher speeds. I was driving the vehicle on the highway and it just shut off and I almost crashed onto the side of the highw…
Read full complaint
The car started shutting off when putting gas and all the ABS lights started turning on. Then it escalated to the car shutting off when pressing the brakes. Now it shuts off randomly never while driving at higher speeds. I was driving the vehicle on the highway and it just shut off and I almost crashed onto the side of the highway because the steering wheel was not working. Thankfully I was able to meet be it a bit and avoid an accident but it happened a few times. Found that some vehicles like mine have some recalls and an extended warranty thing on file and when speaking with a rep at the Lincoln/Ford, she agreed that that what I was experiencing had to do with those, but the car dealerships in my area are not wanting to take responsibility and repair my vehicle which at this point is a public safety hazard not only for my family and me but anyone on the road around me. I can't work or take the car anywhere because of this issue and the carelessness and complete disregard from Ford reps is appalling.
NHTSA ODI #11440831
148,000 miles · Oct 27, 2021
Unknown Or OtherCrashInjury
The contact owned a 2011 Ford Escape. The contact stated while driving at 35-40 MPH, the vehicle rolled over and crashed into a residence yard. The air bags did not deploy. There were no warning lights illuminated. The contact was knocked unconscious and was transported from the vehicle to the hospital with the assistance of eme…
Read full complaint
The contact owned a 2011 Ford Escape. The contact stated while driving at 35-40 MPH, the vehicle rolled over and crashed into a residence yard. The air bags did not deploy. There were no warning lights illuminated. The contact was knocked unconscious and was transported from the vehicle to the hospital with the assistance of emergency units. A police vehicle was filed. The contact sustained fractured vertebrae at the base of the neck, and several lacerations on the buttocks and face. The vehicle was towed to a tow lot, where it was totaled. The dealer was notified of the failure. The manufacturer was not notified of the failure. The approximate failure mileage was 148,000.
NHTSA ODI #11438426
Mileage unknown · Jul 22, 2021
Unknown Or Other
Vehicle stalled while driving. Was able to pull into a parking lot. Car died and would not start and stay running. Acted as if fuel was not getting to engine. This happened approximately 1 month ago. I had car repaired. A relay was thought to be bad in the fuel supply system. Today the same thing occurs, car stalls and dies in f…
Read full complaint
Vehicle stalled while driving. Was able to pull into a parking lot. Car died and would not start and stay running. Acted as if fuel was not getting to engine. This happened approximately 1 month ago. I had car repaired. A relay was thought to be bad in the fuel supply system. Today the same thing occurs, car stalls and dies in few minutes. Again was able to get into a parking lot before it went completely dead. After stopping car starts up but then stumbles and dies in less than a few seconds. Sounds like it is not getting fuel.
NHTSA ODI #11425938
89,000 miles · Jan 19, 2021
Unknown Or Other
THE FRONT SUBFRAME IS RUSTED OUT AND WILL NOT PASS THE PA STATE INSPECTION. THE CAR HAS UNDERCARRIAGE CORROSION PROBLEMS. WE JUST REPLACED THE MUFFLER PIPE FOR SIMILAR ISSUES LAST FALL. THEY CAR HAS BEEN DRIVING IN PA FOR LAST 9 YEARS AND SHOULD NOT BE HAVING THESE ISSUES. THE CAR HAS 89000 MILES. GODSHALLS AUTOMOTIVE CAN GET A …
Read full complaint
THE FRONT SUBFRAME IS RUSTED OUT AND WILL NOT PASS THE PA STATE INSPECTION. THE CAR HAS UNDERCARRIAGE CORROSION PROBLEMS. WE JUST REPLACED THE MUFFLER PIPE FOR SIMILAR ISSUES LAST FALL. THEY CAR HAS BEEN DRIVING IN PA FOR LAST 9 YEARS AND SHOULD NOT BE HAVING THESE ISSUES. THE CAR HAS 89000 MILES. GODSHALLS AUTOMOTIVE CAN GET A USED PART AND LABOR TO FIX WILL BE $1100. THIS SHOULD BE LOOK AT AS A RECALL.
NHTSA ODI #11388783
70,000 miles · Jan 28, 2020
Unknown Or Other
CARRIER BEARING DRIVE SHAFT ASSEMBLY CAUSING SEVERE VIBRATION UPON EXCELERATION AND AND LETTING OFF THE GAS PEDDLE ALSO IGNITION ISSUE PUT KEY IN TURN ON CRANKING SEVERAL TIMES BEFORE STARTING UNLESS KEY IS TURNED BACK MY ESCAPE HAS 70,000 MILES ON IT I SHOULD NOT BE HAVING THESE ISSUES.MY ENGINE LIGHT IS ON AND VEHICLE VIBRATIO…
Read full complaint
CARRIER BEARING DRIVE SHAFT ASSEMBLY CAUSING SEVERE VIBRATION UPON EXCELERATION AND AND LETTING OFF THE GAS PEDDLE ALSO IGNITION ISSUE PUT KEY IN TURN ON CRANKING SEVERAL TIMES BEFORE STARTING UNLESS KEY IS TURNED BACK MY ESCAPE HAS 70,000 MILES ON IT I SHOULD NOT BE HAVING THESE ISSUES.MY ENGINE LIGHT IS ON AND VEHICLE VIBRATION IT HAS NEW TIRES, I REPLACED TIE RODS, BEARINGS, IN FRONT ALL NEW BRAKES THIS VEHICLE HAS BEEN A BIG DISAPPOINTMENT I HAVE PUT A LOT OF MONEY INTO IT AND ONLY 70,000 MILES FOR A 2011.PLEASE HELP ME OUT WITH THIS SITUATION THIS IS THE FIRST FORD I HAVE EVER OWNED I AM NOT A HAPPY CUSTOMER.
NHTSA ODI #11302506
70,285 miles · Dec 23, 2019
Unknown Or OtherInjury
ON DECEMBER 22, 2019 AT APPROXIMATELY 6 PM, OUR SON WAS LOADING GROCERIES HE HAD JUST PURCHASED INTO THE BACK OF THE ESCAPE, WHEN HE CLOSED THE REAR LIFT GATE WINDOW, IT SIMPLY SHATTERED INTO SMALL PIECES. MY SON SUFFERED A SMALL ABRASION ON ONE KNUCKLE BUT IT COULD HAVE BEEN MUCH WORSE. THERE HAD BEEN NO CRACKS OR OTHER SIGNS O…
Read full complaint
ON DECEMBER 22, 2019 AT APPROXIMATELY 6 PM, OUR SON WAS LOADING GROCERIES HE HAD JUST PURCHASED INTO THE BACK OF THE ESCAPE, WHEN HE CLOSED THE REAR LIFT GATE WINDOW, IT SIMPLY SHATTERED INTO SMALL PIECES. MY SON SUFFERED A SMALL ABRASION ON ONE KNUCKLE BUT IT COULD HAVE BEEN MUCH WORSE. THERE HAD BEEN NO CRACKS OR OTHER SIGNS OF DEFECT IN THE WINDOW. THERE IS A FORD TECHNICAL SERVICES BULLETIN (TSB-11-2-9) ON THIS ISSUE BUT WHEN WE CALLED A LOCAL FORD DEALERSHIP AND MENTIONED THE TSB, THEY SAID THAT FORD WOULD NOT PAY T O FIX IT AND THAT THE TSB WAS MERELY INSTRUCTIONS TO THE SERVICE TECHNICIANS ON HOW TO FIX IT. THIS IS BULL. WE ARE AWARE THAT NHTSA HAS RECEIVED MORE THAN 40 COMPLAINS ON THIS ISSUE. OUR SON WAS INJURED, THIS IS A KNOWN SAFETY DEFECT AND FORD SHOULD BE HELD RESPONSIBLE. THE VEHICLE WAS STATIONARY WITH THE ENGINE TURNED OFF WHEN THIS HAPPENED.
NHTSA ODI #11290849
141,000 miles · Oct 17, 2019
Fuel/propulsion SystemService BrakesUnknown Or Other
WHEN TRUCK HAS A FULL OR EVEN HALF TANK , ALWAYS SMELL A LOUD GAS SMELL COMING FROM TRUCK. GAS SMELL SO LOUD CAN NOT HAVE TRUCK PARKED IN GARAGE DUE TO FUMES. ALSO WITH BRAKES, WHEN FORCED TO STOP IMMEDIATELY THE BRAKES MAKE A WEIRD SOUND AND WONT LOCK PROPERLY.
NHTSA ODI #11269178
Official recalls
2Oct 26, 2016
Ford Motor Company (Ford) is recalling certain model year 2010-2012 Ford Escape vehicles manufactured February 26, 2009, to April 29, 2012, and 2010-2011 Mercury Mariner vehicles manufactured February 25, 2009, to December 12, 2010. On vehicles with a 3.0L engine, the Fuel Delivery Module (FDM) may crack, causing a fuel leak.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy: Ford will notify owners, and dealers will replace the FDM flange with one that has a redesigned fuel supply port, free of charge. Remedy parts are currently unavailable. Interim notices were mailed to owners on December 13, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S41.
May 29, 2014
Ford Motor Company (Ford) is recalling certain model year 2008-2011 Ford Escape and Mercury Mariner vehicles manufactured August 18, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.
Consequence & remedy
Consequence: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will update the software for the power steering control module (PSCM) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the PSCM when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on July 18, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S05.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4DP15001 · Loss Of Power Steering While Driving
Opened Apr 1, 2015 · Closed Jun 14, 2018
Status: closed (inferred from source dates) · Steering:electric Power Assist System
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
DP12006 · Electronic Throttle Body Malfunction
Opened Oct 2, 2012 · Closed Feb 21, 2013
Status: closed (inferred from source dates) · Engine
In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.
PE11016 · Rear Liftgate Window Glass Breakage
Opened Apr 27, 2011 · Closed Aug 18, 2011
Status: closed (inferred from source dates) · Structure:body:hatchback/liftgate; Structure:body:hatchback/liftgate:hinge And Attachments; Structure:body:hatchback/liftgate:support Device/strut; Visibility; Visibility:glass, Side/rear
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (5)
Structure:body:hatchback/liftgate
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:hatchback/liftgate:hinge And Attachments
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:hatchback/liftgate:support Device/strut
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Visibility
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Visibility:glass, Side/rear
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Illustration