My Traction Control Lamp, ABS Light, and Brake Light, have all illuminated on the dash at one time when I came out to my car after work. When I went into work there was no lights on. On my way to work there were no lights on, and no brake issues. Now there are. My brake fluid level is full. There is no leaking fluids from the ro…
Read full complaint
My Traction Control Lamp, ABS Light, and Brake Light, have all illuminated on the dash at one time when I came out to my car after work. When I went into work there was no lights on. On my way to work there were no lights on, and no brake issues. Now there are. My brake fluid level is full. There is no leaking fluids from the rotors, brake lines etc. Now all these lights are on, and my brakes are pulsing slightly. I looked today and see there was a recall on this system. I have had this vehicle for 6 years, and I know I never took it in for any recalls. When was this ABS System brake recall? When was it done on this vehicle, and is it possible that the FMC just did the cheapest repairs it could do? I need to know because I have a 4 yr old son that rides with me in this vehicle. I need to know when it was done, and what was done, PLEASE.
NHTSA ODI #11540413
Mileage unknown · Jul 4, 2023
Electrical SystemService BrakesSteering
At 200,000 miles I'm beginning to have problems withe electric power steering along with suspension issues as well. i start my vehicle drive for a bit could be turning or coming to a brake an steering gives out cause me to work to turn it
NHTSA ODI #11530277
Mileage unknown · Apr 3, 2023
Service Brakes
The incident took place on 12/12/22 while driving at about 40-45 mph a truck pulled out Infront of me causing me to unexpectedly break. There were no indicator warning lights on the dash prior to or after the failure. The break went all the way to the floor, luckily we were able to avoid an accident, and myself and my son were j…
Read full complaint
The incident took place on 12/12/22 while driving at about 40-45 mph a truck pulled out Infront of me causing me to unexpectedly break. There were no indicator warning lights on the dash prior to or after the failure. The break went all the way to the floor, luckily we were able to avoid an accident, and myself and my son were just jerked around and held back by the seat belt. The independent garage we use was right around the corner. The vehicle was diagnosed and needed a new master cylinder and abs hydraulic control unit. The part was out of stock and took three months to come in. The vehicle was repaired and received on 3/23/23.
NHTSA ODI #11515098
Mileage unknown · Oct 11, 2022
Service Brakes
We are having the same problems with this vehicle as others are having under Ford recall 19S54 NHTSA identifier 19V904. Three times after applying the brakes hard the brake system required servicing because the pedal would slowly go to the floor while sitting at a traffic light. Other symptoms would be sluggish or spongy braking…
Read full complaint
We are having the same problems with this vehicle as others are having under Ford recall 19S54 NHTSA identifier 19V904. Three times after applying the brakes hard the brake system required servicing because the pedal would slowly go to the floor while sitting at a traffic light. Other symptoms would be sluggish or spongy braking. The last service was at a Goodyear where the service tech commented - left front inlet abs valve sticking, activated it three times with scanner before it started to work. He informed us that there was a recall for this problem that may be applicable to out Escape. I called Ford to report it, Case number [XXX]. Will use this Goodyear appt date to answer following questions. INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
NHTSA ODI #11488769
Mileage unknown · Sep 17, 2022
Service Brakes
ABS Module failure. This is a major issue with these cars and it is extremely dangerous and should be recalled. It causes brake pedal to go to the floor. There’s thousands of cases and parts are unobtainable from manufacturing because they used a one year only part because they were testing it out. There’s been recalls on other …
Read full complaint
ABS Module failure. This is a major issue with these cars and it is extremely dangerous and should be recalled. It causes brake pedal to go to the floor. There’s thousands of cases and parts are unobtainable from manufacturing because they used a one year only part because they were testing it out. There’s been recalls on other models using similar Modules but not on this model.
NHTSA ODI #11484976
Mileage unknown · Jun 29, 2022
Service Brakes
Put car in park. Park can be moved roll away while in park
NHTSA ODI #11471640
Mileage unknown · Jun 27, 2022
Service Brakes
Vehicle was driving on I 75 North bound upon passing Micanopy Rd, and prior to Williston road exit. Driving between 73 to 75 MPH the ABS light came on. ahead of me a semi truck and in my left a car was passing, I tap the brake and the brake system fail to respond. I let the car role and veer to move move to the right, hunk t…
Read full complaint
Vehicle was driving on I 75 North bound upon passing Micanopy Rd, and prior to Williston road exit. Driving between 73 to 75 MPH the ABS light came on. ahead of me a semi truck and in my left a car was passing, I tap the brake and the brake system fail to respond. I let the car role and veer to move move to the right, hunk tat the truck, shoot the emergency brakes and the SUV stop, I called Ford Public relation with no resolution although I was not looking for any compensation or repair cost. The claimed that the warranty of the vehicle was expired. I responded that I was not looking for any compensation, rather I was looking to report a problem that might has cost human lost..... I took the car to the ford dealership in Gainesville Florida to get an authentic report, in order to submit a safety concern to The Ford Motor Safety Department. Dealer and public relations office claimed that Ford Motor Company does not have a safety Department. I am an Industrial Hygienist who Work for OSHA as a COSHO and although I explained no action action seem to indicate that they know,,,,,,,, I question if they understood the issue. This failure may has cost loses, my vehicle is parked at my house This is a 2009 Ford Escape Hybrid VIN [XXX]. PLEASE NOTIFY ME OF ACTION TAKEN. Sincerely, [XXX] INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
NHTSA ODI #11471237
Mileage unknown · Jun 22, 2022
Fuel/propulsion SystemService BrakesWheels
I change my brakes twice in not even a full month My alternator belt came off I replaced it when I put it in park it rolls it shakes and it takes a minute to go faster once I go 40 mph the acceleration pedal vibrates tire pressure sensor stays on and also it keep saying check fuel tank injector
NHTSA ODI #11470548
Mileage unknown · Jun 14, 2022
Service Brakes
Ford 2009 Ford Escape VIN #[XXX] We took our 2009 Ford Escape to Jimmy's Automotive located at 4524 Pacific Ave Lacey Wa We have taken our Ford Escape here for years for service Jimmy's notified us that our ABS brakes were defective (a defect from installation in China) The cost would be over $2000 to repair I called our local F…
Read full complaint
Ford 2009 Ford Escape VIN #[XXX] We took our 2009 Ford Escape to Jimmy's Automotive located at 4524 Pacific Ave Lacey Wa We have taken our Ford Escape here for years for service Jimmy's notified us that our ABS brakes were defective (a defect from installation in China) The cost would be over $2000 to repair I called our local Ford Dealership in Olympia and they stated that our VIN # did not qualify for the ABS brake problem I then called the Ford Company in Detroit MI they stated the same that our VIN # did not qualify for the ABS brake defect I contacted an attorney at Legal Zoom and he recommended contacting you My question how can we not qualify for the defective ABS problem when our vehicle has the defective ABS brake SEE INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
NHTSA ODI #11469195
Mileage unknown · May 24, 2022
Service Brakes
The contact owns a 2009 Ford Escape. The contact stated that while driving at various speeds, the brake pedal would depress to the floorboard without warning. The contact had taken the vehicle to an independent mechanic who initially replaced the brake master cylinder; however, the failure persisted. The vehicle was taken back t…
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated that while driving at various speeds, the brake pedal would depress to the floorboard without warning. The contact had taken the vehicle to an independent mechanic who initially replaced the brake master cylinder; however, the failure persisted. The vehicle was taken back to the mechanic and was diagnosed with a defective ABS module. The manufacturer was also notified and informed him that there were no recalls on his vehicle; he was then transferred to the NHTSA for assistance. The vehicle was not repaired. The failure mileage was unknown.
Ford Motor Company (Ford) is recalling certain model year 2008-2011 Ford Escape and Mercury Mariner vehicles manufactured August 18, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.
Consequence & remedy
Consequence: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will update the software for the power steering control module (PSCM) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the PSCM when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on July 18, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S05.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3
DP15001 · Loss Of Power Steering While Driving
Opened Apr 1, 2015 · Closed Jun 14, 2018
Status: closed (inferred from source dates) · Steering:electric Power Assist System
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
DP12006 · Electronic Throttle Body Malfunction
Opened Oct 2, 2012 · Closed Feb 21, 2013
Status: closed (inferred from source dates) · Engine
In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.
Illustration