The contact owns a 2009 Ford Escape. The contact stated that on several occasions while driving at various speeds, the power train warning light illuminated randomly but disappeared. Additionally, the contact stated that on several occasions when the vehicle was started, the steering wheel became stiff and was difficult to turn.…
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated that on several occasions while driving at various speeds, the power train warning light illuminated randomly but disappeared. Additionally, the contact stated that on several occasions when the vehicle was started, the steering wheel became stiff and was difficult to turn. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure. The failure mileage was approximately 190,000.
NHTSA ODI #11578544
Mileage unknown · Jan 31, 2024
Power Train
Power steering assist fault Torque sensor
NHTSA ODI #11569158
Mileage unknown · Jul 5, 2023
EnginePower TrainSteering
I have had to spend over $5,000 in repairs for this vehicle and I’ve had it for over a year. It was listed at $6,999 at a used car dealership so I got it as is and have had issues ever since. There is no recall on my car according to the VIN# however I strongly disagree with that. When I first got it, it drove great for a week a…
Read full complaint
I have had to spend over $5,000 in repairs for this vehicle and I’ve had it for over a year. It was listed at $6,999 at a used car dealership so I got it as is and have had issues ever since. There is no recall on my car according to the VIN# however I strongly disagree with that. When I first got it, it drove great for a week and then the problems started to arise. Every time I came to a complete stop the car would turn off completely. So I would have to put it in park and turn the key off then restart it and keep it moving a little. This kept going on for 11 months, until it turned off at a stop light and I couldn’t get it to start back up. I was almost hit by traffic coming up behind me (going no less than 45 mph) because of where the car was located. Turns out the motor basically combusted from the inside out. This was caused by the oil leak that could never get fixed because the gasket would always give way. After having to work for 4 months scraping together $3,200 plus paying for a rental car weekly, the motor was replaced and it was working well again. Until it wasn’t. The power steering is controlled by an electric pump which makes you more prone to getting into an accident. My power steering locks up every time I start the car. It did this before the motor was replaced but now it’s even worse since the motor was replaced. I have to turn my car on and off about 15 times before my steering wheel unlocks and I can move it normally. It takes my whole strength to turn the wheel when it locks up. I haven’t been to a ford dealership yet but I do plan on going to get them to check it out since a lot of 2008-2012 Ford Escapes have recalls on the power steering sensor. Long story short. This car has had to have so many repairs for things that normally don’t need repairs every 2 weeks and I want it to get looked into because I’ve never ever had car cost so much in repairs for things that shouldn’t be breaking so fast and easily. I have all the repair paper receipts.
NHTSA ODI #11530359
Mileage unknown · Jul 18, 2022
Electrical SystemPower TrainSteering
First steering column locked with less then 65,000 miles . Now power train wrench light warning popped on less then 80,000 miles . Throttle body issue forcing car into limp mode leaving driver in danger on the road
NHTSA ODI #11474419
Mileage unknown · Jul 17, 2022
Power TrainSteeringWheels
Rear shock mount rusted out and is destroying the inside of my trunk. Now is hanging loose.
NHTSA ODI #11474363
Mileage unknown · Sep 7, 2021
Power TrainSteeringSuspension
Subject vehicle is a 2009 Ford Escape with 74,123 miles. Driving the vehicle the lower control arm separated from the front frame otherwise known as the engine cradle or subframe. The failure is identical to the subframe failures on the 2001 - 2004 Ford Escapes currently under recall. The failure was immediate with no prior war…
Read full complaint
Subject vehicle is a 2009 Ford Escape with 74,123 miles. Driving the vehicle the lower control arm separated from the front frame otherwise known as the engine cradle or subframe. The failure is identical to the subframe failures on the 2001 - 2004 Ford Escapes currently under recall. The failure was immediate with no prior warning. The vehicle exhibited loss of steering control, wheel lock up from the front tire contacting the back of the wheel opening, and loss of transmission engagement from cv joint separation. In my opinion, whatever PCA actions or quality root cause was identified by Ford Motor Company during the prior recall investigation isolating the condition to 2001 - 2004 Escapes was either incomplete or inaccurate. This is supported by the same failure occurring in Escapes outside of that model year window. No mechanism was added after the 2004 Escapes were produced to prevent this failure from occurring. Images attached show the failure that was experienced. I was unable to obtain a good used frame locally that did not exhibit signs of corrosion with perforation present or starting. This further supports the failure mode is beyond the scope of the initial recall. The recall should be expanded to prevent future accidents that could have the potential for injury or death.
NHTSA ODI #11432006
Mileage unknown · Sep 7, 2021
Power TrainSteeringSuspension
Subject vehicle was a 2009 Ford Escape with 74,123 miles. Driving the vehicle the front passenger lower control arm separated from the k-frame/cradle causing the vehicle to lose control. Loss of steering was experienced as well as tire lock up from the front tire lodging against the back of the fender. The CV shaft also separat…
Read full complaint
Subject vehicle was a 2009 Ford Escape with 74,123 miles. Driving the vehicle the front passenger lower control arm separated from the k-frame/cradle causing the vehicle to lose control. Loss of steering was experienced as well as tire lock up from the front tire lodging against the back of the fender. The CV shaft also separated during the failure resulting in loss of transmission engagement. There was no warning prior to the event, the failure was sudden and immediate. The loss of vehicle control was extreme. Failure is identical to RCRIT-14V165-9596 for the 01-04 Escapes. The reason the recall was only isolated to the 01-04 Escapes is unknown. In my opinion, whatever PCA actions or supplier related issues identified by Ford Motor Company during the prior recall investigation to support the recall only affecting 01-04 model years was either incomplete or inaccurate. The frame rust through condition extends beyond the model years listed in the recall and was not resolved as shown by subsequent failures on vehicles outside of the recall model year window. No mechanism was put in place to prevent the control arm separation in the later model year Escapes to prevent the same safety issue from occurring. I was unable to obtain a front cradle from a local salvage yard that did not exhibit perforation present or starting supporting this condition is occurring on all model year Escapes from 2001 to 2012 in corrosion prone areas. The recall should be extended to all model years involved to prevent potential accidents.
NHTSA ODI #11431998
95,000 miles · Feb 10, 2021
Power Train
I SUDDENLY LOST POWER WHILE DRIVING ON CITY STREETS AND HAD THE CHECK ENGINE LIGHT AND WRENCH LIGHT COME ON. UPON RESEARCHING THE ISSUE IT WAS FOUND TO MOST LIKELY BE A FAULTY THROTTLE BODY. ALSO I CAN NOT DRIVE ON THE FREEWAY FOR MORE THAN 5-10 MINUTES AT 60 MPH BEFORE IT STARTS TO SHIMMY AND BECOME UNSAFE TO DRIVE.
NHTSA ODI #11395521
197,000 miles · Dec 29, 2020
Electrical SystemPower TrainService Brakes
MY FORD ESCAPE LIMETED JUST STARTED MAKING A NOISE OUT OF NOWHERE AND BEFORE IT STARTED I WOULD MAKE A RIGHT TURN AND IT WOULD STOP RUNNING
NHTSA ODI #11385530
133,000 miles · Nov 12, 2020
EnginePower Train
WHILE DRIVING MY 2009 FORD ESCAPE IT BEGAN TO SLOW DOWN. I PRESSED THE ACCELERATOR EVEN MORE, BUT THE CAR CAME TO A COMPLETE HALT AND THE LIGHTS ON THE DASHBOARD ALL TURNED ON. I BRAKED, PLACE IT TO PARKING AND TURNED THE ENGINE OFF. I RESTART THE CAR AND WAS ABLE TO DRIVE AWAY. THIS HAS OCCURRED 4 TIMES ALREADY IN THE PAST …
Read full complaint
WHILE DRIVING MY 2009 FORD ESCAPE IT BEGAN TO SLOW DOWN. I PRESSED THE ACCELERATOR EVEN MORE, BUT THE CAR CAME TO A COMPLETE HALT AND THE LIGHTS ON THE DASHBOARD ALL TURNED ON. I BRAKED, PLACE IT TO PARKING AND TURNED THE ENGINE OFF. I RESTART THE CAR AND WAS ABLE TO DRIVE AWAY. THIS HAS OCCURRED 4 TIMES ALREADY IN THE PAST 2 MONTHS. EACH TIME THIS HAS OCCURRED, I'VE BEEN DRIVING LESS THAN 40 MPH. I'VE TAKEN THE CAR TO THE SHOP TO GET SCANNED AND NOTHING HAS BEEN DETECTED.
Ford Motor Company (Ford) is recalling certain model year 2008-2011 Ford Escape and Mercury Mariner vehicles manufactured August 18, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.
Consequence & remedy
Consequence: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will update the software for the power steering control module (PSCM) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the PSCM when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on July 18, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S05.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3
DP15001 · Loss Of Power Steering While Driving
Opened Apr 1, 2015 · Closed Jun 14, 2018
Status: closed (inferred from source dates) · Steering:electric Power Assist System
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
DP12006 · Electronic Throttle Body Malfunction
Opened Oct 2, 2012 · Closed Feb 21, 2013
Status: closed (inferred from source dates) · Engine
In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.
Illustration