NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
1,134 reportsMileage unknown · Aug 23, 2021
Engine
I've had the car for a year and it suddenly loses power during acceleration and Is throwing the P0299 turbocharger code. I was getting on the interstate when the car did this the 1st and 2nd times. It was a very busy time of day and my car suddenly decellerated in front of an 18 wheeler with my kids in the car. NO MATTER how ha…
Read full complaint
I've had the car for a year and it suddenly loses power during acceleration and Is throwing the P0299 turbocharger code. I was getting on the interstate when the car did this the 1st and 2nd times. It was a very busy time of day and my car suddenly decellerated in front of an 18 wheeler with my kids in the car. NO MATTER how hard I hit the gas it would not go and I almost got ran over by a tractor trailer. I had to slam on brakes and squeeze between the on ramp and a bridge guardrail to not be hit.
NHTSA ODI #11430178
Mileage unknown · Aug 23, 2021
Service Brakes, Hydraulic
On 8-15-21 as I was driving, I was suddenly unable to break properly and had to depress the peddle almost down to the floor to engage the breaks. This happened one isolated time one month prior but went away. I had the car towed to Walnut Creek CA Ford for service where after multiplier test drives replicated the problem, flushe…
Read full complaint
On 8-15-21 as I was driving, I was suddenly unable to break properly and had to depress the peddle almost down to the floor to engage the breaks. This happened one isolated time one month prior but went away. I had the car towed to Walnut Creek CA Ford for service where after multiplier test drives replicated the problem, flushed the break line and determined I needed a new HCU because of a sticking valve. I researched the issue and discovered this exact issue was the subject of a Ford recall in 2019 but of other models not including mine. I called Ford to see if they would cover the cost since it was a safety issue that they recognized in a very large recent recall that was the result of over 25 accidents and multiple deaths. Ford refused to cover the cost. NHTSA should be aware of this safety issue because it is effecting more cars than covered.
NHTSA ODI #11430169
69,000 miles · Aug 20, 2021
Latches/locks/linkages
The contact owns a 2012 Ford Edge. The contact stated that the latch on the driver’s side door failed to operate intermittently with the door ajar warning light illuminated. The vehicle was not been diagnosed nor repaired. A diagnostic test was scheduled but was still pending. The manufacturer was notified of the failure and inf…
Read full complaint
The contact owns a 2012 Ford Edge. The contact stated that the latch on the driver’s side door failed to operate intermittently with the door ajar warning light illuminated. The vehicle was not been diagnosed nor repaired. A diagnostic test was scheduled but was still pending. The manufacturer was notified of the failure and informed the contact to file a complaint with the NHTSA. The failure mileage was approximately 69,000.
NHTSA ODI #11429901
Mileage unknown · Aug 18, 2021
Service Brakes, Hydraulic
In June of 2018 with 48,182 miles on my vehicle, I experienced the brake pedal very hard to push some of the time, and then other times, the brakes would not stop and you could hear air come out from the brake pedal. Realizing this was a hazard for myself and other drivers, I took my car into a Ford Dealership. They stated tha…
Read full complaint
In June of 2018 with 48,182 miles on my vehicle, I experienced the brake pedal very hard to push some of the time, and then other times, the brakes would not stop and you could hear air come out from the brake pedal. Realizing this was a hazard for myself and other drivers, I took my car into a Ford Dealership. They stated that there was a recall on the brake booster and replaced the part free of charge. In November of 2020 with 80,060 miles on my vehicle, the exact thing happened again. I contacted the Ford Dealership, they stated there is no other recall and because it had been over 12 months from the first replacement that they could not replace it free of charge, so I paid a shop over $500 to replace the brake booster again. Now, August 17th, 2021 less than 9 months later and only 10,000 more miles on my vehicle it has happened again! The Ford Dealership recommended that I contact Ford's corporate office. Ford Corporate told me that they will not cover the cost to repair my vehicle for the 3rd time and will not provide the part free of charge. This is an obvious issue with their brake booster part or a deeper issue that isn't being addressed, leaving vehicle owners, like myself, at risk of getting into an accident due to a faulty brake system.
NHTSA ODI #11429599
Mileage unknown · Aug 12, 2021
Unknown Or Other
Brakes continually malfunction and fail intermittently. It has been an ongoing issue for just over two years. We have found they malfunction and fail after any loss of traction, such as turning on a gravel road or hitting a pothole. For quite some time we have been able to stop and pump the brakes hard and hold them down, repeat…
Read full complaint
Brakes continually malfunction and fail intermittently. It has been an ongoing issue for just over two years. We have found they malfunction and fail after any loss of traction, such as turning on a gravel road or hitting a pothole. For quite some time we have been able to stop and pump the brakes hard and hold them down, repeating until the brakes tightened back up. The last 3 days however they will not function properly. This malfunction/ failure causes extremely spongey brakes making it extremely difficult to slow or stop, having to push the pedal nearly to the floor to start slowing down. Problem had not been reproduced by servicer however we could reproduce the problem once we determined it was a loss of traction causing it. NO warning lights of ANY kind have ever Illuminated! System check always shows brakes are good. Brake fluid is always good. Brakes have been bled multiple times, replaced and brake booster has been replaced as that is what the dealer thought it was the last time i had it checked. Brake booster did NOT fix the hissing or the malfunctioning or failure. So many people with an Edge have brake issues! Please help us get this resolved and corrected before someone gets seriously injured or dies! I have nearly every single date my brakes have malfunctioned/failed and I will provide if requested!
NHTSA ODI #11428783
Mileage unknown · Aug 10, 2021
Electrical System
I was driving the car approximately 35 MPH the car completely shut down. A couple of days later while accelerating from a stop sign it completely shut off again.
NHTSA ODI #11428606
Mileage unknown · Aug 2, 2021
Service Brakes
Brakes were working totally fine for 1 hr. drive to city. A few hours later, I returned to my car to drive home. When I put my foot on the brake pedal while it was in park (but engine started,) everything felt normal. When I put it into reverse to back out of the spot, my foot went all the way to the floor. This "soft pedal"…
Read full complaint
Brakes were working totally fine for 1 hr. drive to city. A few hours later, I returned to my car to drive home. When I put my foot on the brake pedal while it was in park (but engine started,) everything felt normal. When I put it into reverse to back out of the spot, my foot went all the way to the floor. This "soft pedal" occurred with NO warning lights/sounds/etc. There was NO warning that my brakes would give out on me at all. Luckily, mine happened,(both occasions), in parking lots, not in higher speed situations. Any higher speed situation could have been catastrophic. It was frightening. Fortunately, I was a nearly vacant lot, so I tried backing up to see what would happen and the brake again had to go ALL THE WAY to the floor and made a grinding sound (like stopping on gravel sort of). It did not stop as usual. It rolled to a stop after traveling a few feet. (Mind you, this is only rolling back from a parked position.) I got on You Tube and typed in "2012 Ford Edge, brake to the floor" there were hundreds of folks complaining about this issue. It is related to the ABS Hydraulic Control Unit, although my ABS never illuminated. You Tube had "quick temporary fix". Go in reverse upto 20-25 MPH and slam on the brakes "grenade stopping". Took 7 times (frightening given I didn't know if the brakes would engage at all), my brake pedal popped back up from the floorboard and it felt like a hard pedal again. It worked fine for one day. The same problem reoccurred the next day. Same reverse/grenade stop procedure and it got me to the dealership. Apparently this gets the valve to go back to closed position after air got in HCU from open valve. My Ford Service Advisor acknowledged how common the repair was and were surprised the Edges weren't included in the 19S54 Recall with other models. Repair cost me $1,435. They also found the Master Cylinder needed some repair-more money. I will try to get the actual part removed from my car back for inspection
NHTSA ODI #11427541
Mileage unknown · Jul 30, 2021
Back Over Prevention
While backing up, the camera will often reverse the view or flip upside down. Other times it will suddenly black out. All result a scary and unsafe situation. Especially when reversed and it looks clear on the wrong side!!
NHTSA ODI #11427163
Mileage unknown · Jul 8, 2021
Service Brakes
Brakes peddle soft, fluid full, intermittent times where putting on the brake and felt they weren’t working (scary). Pads, rotors fine. Taking in to dealer and anticipate they will replace brake booster, master brake cylinder and still the brake issue remains not fixed. Reading posts on internet and many owners having same issu…
Read full complaint
Brakes peddle soft, fluid full, intermittent times where putting on the brake and felt they weren’t working (scary). Pads, rotors fine. Taking in to dealer and anticipate they will replace brake booster, master brake cylinder and still the brake issue remains not fixed. Reading posts on internet and many owners having same issue where dealer can’t seemed to be able to determine problem.
NHTSA ODI #11424008
Mileage unknown · Jul 7, 2021
Unknown Or Other
As I was driving, all of a sudden the car would not pick up speed. I gently put additional pressure on the gas, but nothing happened. I was lucky as I was going out to my mom's. As I pulled into the drive way I heard thumping noises (that is the best way I can explain the sound). Turned car off, visited with my mom, hours later …
Read full complaint
As I was driving, all of a sudden the car would not pick up speed. I gently put additional pressure on the gas, but nothing happened. I was lucky as I was going out to my mom's. As I pulled into the drive way I heard thumping noises (that is the best way I can explain the sound). Turned car off, visited with my mom, hours later drove home not issues / no light indicators. About a month later I was approaching a stop sign. As I proceeded after the red light turned green, the car again would not increase in speed. I gently applied more pressure to the gas pedal but it would not pick up speed. I had my foot on the gas almost to the floor. I was approaching an overpass but was skeptical about the car gaining speed enough to go over it. I thought best to pull over and seek other options. I called a tow truck and had it towed to my home. The following Monday I had taken it to a repair shop. The garage had it for two days and was unable to detect any thing wrong. This is a serious issue, if this would of happened on a busy freeway, this could result in serious accident in which fatalities could have happened. Losing power on a busy freeway is a disaster waiting to happen. I know my car, this has happened to me two times within 3 months. I am afraid to drive it and have take steps to correct this, but garages "cannot fix what they cannot find". So tell me FORD corporation what advice are giving to you consumers? Or are you going to wait until someone gets killed ?
NHTSA ODI #11423806
Official recalls
3Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Sep 7, 2012
Ford is recalling certain 2012 Edge vehicles manufactured from September 2, 2010, through October 31, 2011, equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will repair the vehicles free of charge. The safety recall began on September 27, 2012. Owners may contact Ford Motor Company Customer Relationship Center at 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Illustration