Wow, vehicle is in park and idling. My traction control light comes on then my brakes go all the way to the floor. It has done about six times so far.
2012 Ford Edge
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2012 Ford Edge do not stand out strongly from the model-year median of 724.
About this comparison →How this year compares
Owner complaints by model year
Compare all Edge years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
874 reports with mileage · 260 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 462 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 247 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 168 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
Service Brakes complaints
247 reportsbreak booster
There was no warning stated in the dash, but I went to drive my car one day and the brakes were sunk to the floor. I drove it around carefully for a little bit and realized the brake pedal built pressure if it was constantly being pressed, however, it would lose the pressure instantly. I got the brakes bled and replaced a brake …
Read full complaint
There was no warning stated in the dash, but I went to drive my car one day and the brakes were sunk to the floor. I drove it around carefully for a little bit and realized the brake pedal built pressure if it was constantly being pressed, however, it would lose the pressure instantly. I got the brakes bled and replaced a brake line since I had replaced both of the rear calipers prior (no issues there and no issues with brake pads or the brakes themselves). A few weeks went by and I lost the pressure again instantly. I called the mechanic to take a look and they replaced the brake booster and master cylinder and bled the brakes. The brake lines/hoses were fine with no leaks. I picked the vehicle up and the brake pedal is still soft and mushy with no pressure building. I am scared to drive it in case I accidentally hit someone and it is currently winter (snow & ice). I have new tires but I fear the brakes will give out on me soon. I don’t think these parts are up for inspection or whether the issue is with the abs module or the HCU, but it appears to be a common issue with 2012 ford edges and other years. The time frame for this is all within 10 weeks since I wasn’t driving my vehicle for about 4 weeks.
Brakes malfunction, the vehicle experienced an apparent loss of brake pressure, resulting in the brake pedal sinking to the floorboard before the vehicle came to a complete stop. A technician serviced the car on three different occasions, replacing the brake booster and bleeding the hydraulic system on 9/11/2023. The problem per…
Read full complaint
Brakes malfunction, the vehicle experienced an apparent loss of brake pressure, resulting in the brake pedal sinking to the floorboard before the vehicle came to a complete stop. A technician serviced the car on three different occasions, replacing the brake booster and bleeding the hydraulic system on 9/11/2023. The problem persisted, taking car to technician for further analysis on three separate occasions, noticing a strange noise while pressing the brake pedal, described as a “wind blowing” noise. After more work, brake malfunction happened again on 1/3/2024.
The brakes extremely stiff while being depressed. While backing out of garage ended up in side lawn. I have to use an excessive amount of force to break normally and avoid a collision with another vehicle. A local service technician diagnosed the issue and determined the cause to be a faulty brake booster. The technician re…
Read full complaint
The brakes extremely stiff while being depressed. While backing out of garage ended up in side lawn. I have to use an excessive amount of force to break normally and avoid a collision with another vehicle. A local service technician diagnosed the issue and determined the cause to be a faulty brake booster. The technician recommended replacing the brake booster. He noted that his internet search was flooded with complaints about this situation and he showed me where q Ford dealership had fixed the problem by replacing the brake booster under Customer Satisfaction Program 13N02. I tried calling Ford to see if they would replace the booster under this program and because and Ford told me the age of my car and mileage was outside scope of this program. Cost precludes me from fixing this. Disappointed in Ford. Will keep using excessive force to brake.
The contact owns a 2012 Ford Edge. The contact stated that while driving downhill and depressing the brake pedal, the brake pedal became very soft and extended to the floorboard. The vehicle was taken to the local mechanic who replaced the brake master cylinder, brake pads, and calipers; however, the failure reoccurred. The vehi…
Read full complaint
The contact owns a 2012 Ford Edge. The contact stated that while driving downhill and depressing the brake pedal, the brake pedal became very soft and extended to the floorboard. The vehicle was taken to the local mechanic who replaced the brake master cylinder, brake pads, and calipers; however, the failure reoccurred. The vehicle was taken back to the mechanic who serviced the brake lines and informed that the brake booster might also be faulty. The manufacturer was notified of the failure and informed the contact that the vehicle did not qualify for the manufacturer's warranty campaign to replace the brake booster. The local dealer was not contacted. The failure mileage was 143,000.
I am one of thousands of people who have had the power brake booster fail on their Ford Edge. Initially, my vehicle failed to stop at an intersection when another vehicle was running the red light, and I was nearly t-boned. The brake pedal was almost impossible to press in. I thought the issue was due to the icy conditions at th…
Read full complaint
I am one of thousands of people who have had the power brake booster fail on their Ford Edge. Initially, my vehicle failed to stop at an intersection when another vehicle was running the red light, and I was nearly t-boned. The brake pedal was almost impossible to press in. I thought the issue was due to the icy conditions at the time and some problem with the ABS. This summer the real problem became apparent as the brakes have started squealing and hissing every time they are pressed, and the pressure required to come to a full stop varies from nearly none and jerking to an immediate stop to the point I am barely able to press the pedal hard enough to get it to stop at all. Sometimes both situations will occur during one stop, and the brake pedal will go from excessively resistant to dropping to the floor, at which point I will lose all stopping power momentarily while I let the pedal slowly hiss back into place and press it again. The first time that happened, I was trying to stop for a bike that started to cross without waiting for the crosswalk signal, and I nearly hit them. Ford’s site states I’m covered under the CSP for this part, but I am unable to find a dealer willing to provide the service as they believe the CSP only covers 10 years after the model year (my mileage is under the 150k limit). Whether or not that’s true, a CSP is insufficient in this scenario as a quick internet search shows power brake booster failure is very common in this model line and it is unequivocally a life and safety risk.
Intermittently when you hit a bump, the brake pedal goes to the floor and may stay that way for a couple of days and then it comes back. This is the second brake booster ford replaced, I see that brakes are a constant problem on these vehicles, this repair is costing me a $1000.00 the car only has 90000 miles on it. My wife is a…
Read full complaint
Intermittently when you hit a bump, the brake pedal goes to the floor and may stay that way for a couple of days and then it comes back. This is the second brake booster ford replaced, I see that brakes are a constant problem on these vehicles, this repair is costing me a $1000.00 the car only has 90000 miles on it. My wife is afraid to drive it anymore.
The contact owns a 2012 Ford Edge. The contact stated that while depressing the brake pedal to stop the vehicle, the brake pedal had extended to the floorboard causing the braking distances to become extended. The vehicle was taken to the local mechanic who diagnosed that the brake valve had become stuck. The vehicle was not yet…
Read full complaint
The contact owns a 2012 Ford Edge. The contact stated that while depressing the brake pedal to stop the vehicle, the brake pedal had extended to the floorboard causing the braking distances to become extended. The vehicle was taken to the local mechanic who diagnosed that the brake valve had become stuck. The vehicle was not yet repaired. The local dealer and manufacturer were not contacted regarding the failure. The failure mileage was 132,000.
The brakes on this vehicle have gradually become worse over time. Even with replacing the pads, rotors. They are spongy and the pedal drops almost to the floor. This causes a delay in braking.
Official recalls
314V393000 · Power Train:axle Assembly:axle Shaft
Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
14V002000 · Fuel System, Gasoline
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
12V438000 · Fuel System, Gasoline:delivery:hoses, Lines/piping, And Fittings
Sep 7, 2012
Ford is recalling certain 2012 Edge vehicles manufactured from September 2, 2010, through October 31, 2011, equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will repair the vehicles free of charge. The safety recall began on September 27, 2012. Owners may contact Ford Motor Company Customer Relationship Center at 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Illustration