I HAD THE BRAKE BOOSTER, MASTER CYLINDER, NEW BRAKE PADS AND BRAKE HYDRAULIC SYSTEM REPLACED 5 MONTHS AGO AND NOW IT'S DOING THE SAME THING AGAIN. BRAKES ARE HARD TO PUSH AND VERY DIFFICULT TO STOP OR GO ALL THE WAY DOWN. ALSO, BURNING SMELL AROUND THE BRAKES. VERY DANGEROUS.
2012 Ford Edge
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2012 Ford Edge do not stand out strongly from the model-year median of 724.
About this comparison →How this year compares
Owner complaints by model year
Compare all Edge years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
874 reports with mileage · 260 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 462 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 247 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 168 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
Service Brakes complaints
247 reportsWHEN APPROACHING AN INTERSECTION THE BRAKES FAILED AND BRAKE PEDAL FELL ALL THE WAY TO THE FLOOR, FORCING ME TO TURN INTO CURB TO AVOID BEING HIT BY CROSS TRAFFIC. THIS IS AN INTERMITTENT ISSUE THAT OCCURS WHEN PRESSURE IS PLACED ON THE SYSTEM. THE FORD DEALERSHIP HAS ALREADY REPLACED THE BRAKE BOOSTER AND MASTER CYLINDER (TWICE…
Read full complaint
WHEN APPROACHING AN INTERSECTION THE BRAKES FAILED AND BRAKE PEDAL FELL ALL THE WAY TO THE FLOOR, FORCING ME TO TURN INTO CURB TO AVOID BEING HIT BY CROSS TRAFFIC. THIS IS AN INTERMITTENT ISSUE THAT OCCURS WHEN PRESSURE IS PLACED ON THE SYSTEM. THE FORD DEALERSHIP HAS ALREADY REPLACED THE BRAKE BOOSTER AND MASTER CYLINDER (TWICE) AND THEY CANNOT DUPLICATE THE ISSUE. THIS HAS ALMOST CAUSED SEVERAL WRECKS, AS THERE IS TYPICALLY NO WARNING SIGNS TO WHEN IT MAY OCCUR.
MY WIFE WAS DRIVING TO WORK AFTER DROPPING OUR 2 YEAR OLD OFF AT GRANDMAS. SHE WENT TO SLOW FOR A STALE GREEN LIGHT AND THE BRAKE PEDAL WENT TO THE FLOOR. LUCKILY SHE WAS ALMOST TO WORK AT THIS POINT. WE HAD THE VEHICLE TOWED TO MY SHOP. REPLACE THE BRAKE BOOSTER BECAUSE IT HAS A KNOWN ISSUE ( NO RECALL JUST WARRANTY EXTENSION),…
Read full complaint
MY WIFE WAS DRIVING TO WORK AFTER DROPPING OUR 2 YEAR OLD OFF AT GRANDMAS. SHE WENT TO SLOW FOR A STALE GREEN LIGHT AND THE BRAKE PEDAL WENT TO THE FLOOR. LUCKILY SHE WAS ALMOST TO WORK AT THIS POINT. WE HAD THE VEHICLE TOWED TO MY SHOP. REPLACE THE BRAKE BOOSTER BECAUSE IT HAS A KNOWN ISSUE ( NO RECALL JUST WARRANTY EXTENSION), ALSO REPLACED THE MASTER CYLINDER BECAUSE THIS WAS CLEARLY A HYDRAULIC FAILURE IN THE BRAKE SYSTEM. DRIVING THE VEHICLE HOME THAT NIGHT WITH A GOOD PEDAL UNTIL I GET TO THE OFF RAMP, AT 70 MILES AN HOUR THERE IS NO LONGER ANY BRAKE PEDAL AND HAD TO USE THE TRANSMISSION TO SAFELY SLOW THE VEHICLE. NOW MY WIFE IS TERRIFIED TO DRIVE HER VEHICLE IN FEAR THAT THE PEDAL IS THERE ONE MINUTE AND GONE THE NEXT.
I WAS ON 222 IN KUTZTOWN PA IT WAS RAIN THE VECHILE IN FRONT OF SLAMMED ON HIS BRAKES I IN TURN DID THE SAMETHING EXCEPT THEIR WAS NO ABS THE BRAKE PEDAL WENT ALL THE WAY TO THE FLOOR I HAD ENOUGH DISTANCE BETWEEN ME AND THE OTHER THE OTHER CARME TO A STOP THE BRAKES WERE VERY SPONGY.THE VECHILE WAS TOWED TO A DEALERSHIP. THE DE…
Read full complaint
I WAS ON 222 IN KUTZTOWN PA IT WAS RAIN THE VECHILE IN FRONT OF SLAMMED ON HIS BRAKES I IN TURN DID THE SAMETHING EXCEPT THEIR WAS NO ABS THE BRAKE PEDAL WENT ALL THE WAY TO THE FLOOR I HAD ENOUGH DISTANCE BETWEEN ME AND THE OTHER THE OTHER CARME TO A STOP THE BRAKES WERE VERY SPONGY.THE VECHILE WAS TOWED TO A DEALERSHIP. THE DEALERSHIP REPLACED THE BRAKE BOOSTER, THE ABS BOOSTER, REAR BRAKE PADS AND ROATERS.THE BRAKE PADS AND ROATORS WERE NEW APRIL 2017 AND INSPECTED IN MAY 2018 THEY WERE FINE.ONLY 13000 MILES WERE PUT ON THE CAR SINCE 2017.ON THE WAY HOME TODAY THE BRAKES WENT OUT AGAIN.
WHEN THE BRAKE ABS SYSTEM ENGAGED, SEVERAL MINUTES LATER THE BAKE PEDAL WENT TO THE FLOOR AND THE BAKES FAILED.
8-11-2016 COMPLETE BRAKE FAILURE WHILE IN MOTION, BRAKE PEDAL TRAVELS TO FLOOR WITH NO POWER ASSIST. DEALER DIAGNOSES AND REPLACES BRAKE BOOSTER. 9-24-2018 COMPLETE BRAKE FAILURE UNABLE TO STOP AT HIGHWAY SPEEDS. MANAGED TO GET TO SAFETY. PEDAL TRAVELS TO FLOOR NO STOPPING. CALLED DEALER ONCE MORE, WAS ADVISED TO CONT…
Read full complaint
8-11-2016 COMPLETE BRAKE FAILURE WHILE IN MOTION, BRAKE PEDAL TRAVELS TO FLOOR WITH NO POWER ASSIST. DEALER DIAGNOSES AND REPLACES BRAKE BOOSTER. 9-24-2018 COMPLETE BRAKE FAILURE UNABLE TO STOP AT HIGHWAY SPEEDS. MANAGED TO GET TO SAFETY. PEDAL TRAVELS TO FLOOR NO STOPPING. CALLED DEALER ONCE MORE, WAS ADVISED TO CONTACT FORD FOR COVERAGE OF WORK AS IT IS OUT OF WARRANTY. DO NOT WANT THIS VEHICLE WITH 2 BRAKE FAILURE EVENTS. PENDING SERVICE CASE.
ON 9/18/18 WHILE TRAVELING HOME FROM DOING SOME ERRANDS WENT TO APPLY BRAKES TO SLOW AND TURN AND PEDAL WENT TO THE FLOOR, PUMPED THEM A FEW TIMES TO STOP AND SINCE THEY HAVE PROGRESSIVELY GOTTEN WORSE TO A POINT OUR MECHANIC SUGGESTED NOT TO DRIVE THE VEHICLE. AFTER SOME RESEARCH IT LOOKS LIKE A COMMON PROBLEM FOR THE EDGE! IS …
Read full complaint
ON 9/18/18 WHILE TRAVELING HOME FROM DOING SOME ERRANDS WENT TO APPLY BRAKES TO SLOW AND TURN AND PEDAL WENT TO THE FLOOR, PUMPED THEM A FEW TIMES TO STOP AND SINCE THEY HAVE PROGRESSIVELY GOTTEN WORSE TO A POINT OUR MECHANIC SUGGESTED NOT TO DRIVE THE VEHICLE. AFTER SOME RESEARCH IT LOOKS LIKE A COMMON PROBLEM FOR THE EDGE! IS FORD GOING TO STEP UP?? SOUNDS LIKE A COSTLY ADVENTURE. FORD NEEDS TO TAKE RESPONSIBILITY!! REACHED OUT TO FORD FOR RECALL INFO. AND THERE HAPPENS TO NONE FOR MY VEHICLE. THEY SUGGESTED TO BRING TO A FORD DEALER MECHANIC AND AFTER DIAGNOSIS MAYBE FORD WILL HELP EASE THE FINANCIAL PAIN. MAYBE! UNFORTUNATELY FORD MECHANICS ARE MORE THAN DOUBLE THE COST OF OUR MORE THAN CAPABLE MECHANIC. FOR THE SAFETY OF ALL EDGE OWNERS PLEASE ISSUE A RECALL.
WHILE DRIVING VEHICLE BRAKE PEDAL WENT TO THE FLOOR MAKING THE VEHICLE ALMOST IMPOSSIBLE TO STOP. I TOOK THE VEHICLE TO A MECHANIC WHO REPLACED THE BRAKES AND MASTER CYLINDER HOWEVER THAT DID NOT CORRECT THE PROBLEM OF NO BRAKE PEDAL. I THEN TOOK THE VEHICLE TO FORD WHERE THEY ADVISED THAT THEY HAVE SEEN A RASH OF THIS PROBLEM, …
Read full complaint
WHILE DRIVING VEHICLE BRAKE PEDAL WENT TO THE FLOOR MAKING THE VEHICLE ALMOST IMPOSSIBLE TO STOP. I TOOK THE VEHICLE TO A MECHANIC WHO REPLACED THE BRAKES AND MASTER CYLINDER HOWEVER THAT DID NOT CORRECT THE PROBLEM OF NO BRAKE PEDAL. I THEN TOOK THE VEHICLE TO FORD WHERE THEY ADVISED THAT THEY HAVE SEEN A RASH OF THIS PROBLEM, AND ADVISED THAT IT IS MOST LIKELY THE ABS CONTROL MODULE. THE VEHICLE IS AT THE FORD DEALERSHIP AS I TYPE. THIS IS THE SECOND ISSUE WITH THIS VEHICLE, THE FIRST WAS A BRAKE BOOSTER FAILURE THAT MADE THE BRAKE PEDAL VERY HARD TO PUSH.
BRAKE BOOSTER WENT OUT, DOOR AJAR KEEPS COMING AND LEAVES MY INTERIOR LIGHTS ON DRAING BATTERY
THE ORIGINAL POWER BRAKE BOOSTER FAILED AND WAS REPLACED. THE SECOND POWER BRAKE BOOSTER FAILED AND ANOTHER ONE WAS REPLACED. THE FORD DEALERSHIP DID NOT WANT TO RECOGNIZE THAT THERE WAS A PROBLEM WITH THIS PART AGAIN AND PASSED IT OFF AS SOMETHING ELSE (REAR CALIPER) CAUSING THE BRAKES TO LOOSE PRESSURE. I HOPE A REVIEW OF T…
Read full complaint
THE ORIGINAL POWER BRAKE BOOSTER FAILED AND WAS REPLACED. THE SECOND POWER BRAKE BOOSTER FAILED AND ANOTHER ONE WAS REPLACED. THE FORD DEALERSHIP DID NOT WANT TO RECOGNIZE THAT THERE WAS A PROBLEM WITH THIS PART AGAIN AND PASSED IT OFF AS SOMETHING ELSE (REAR CALIPER) CAUSING THE BRAKES TO LOOSE PRESSURE. I HOPE A REVIEW OF THESE PARTS WILL BE MADE FOR OTHER DRIVER'S SAFETY. SEE ATTACHMENTS.
Official recalls
314V393000 · Power Train:axle Assembly:axle Shaft
Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
14V002000 · Fuel System, Gasoline
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
12V438000 · Fuel System, Gasoline:delivery:hoses, Lines/piping, And Fittings
Sep 7, 2012
Ford is recalling certain 2012 Edge vehicles manufactured from September 2, 2010, through October 31, 2011, equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will repair the vehicles free of charge. The safety recall began on September 27, 2012. Owners may contact Ford Motor Company Customer Relationship Center at 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Illustration