NHTSA owner reports · September 18, 2026 snapshot.
Electrical System complaints
29 reportsClear category filterMileage unknown · Aug 13, 2026
Electrical SystemFuel/propulsion SystemService Brakes
While driving, I experienced the brakes beginning to fail, followed shortly by a complete loss of engine power. My 2021 Ford Bronco is subject to recall 25S75 (NHTSA 25V455) for a low pressure fuel pump defect that can cause loss of fuel pressure or flow and engine stall. I was stranded on the side of the interstate in 100 degre…
Read full complaint
While driving, I experienced the brakes beginning to fail, followed shortly by a complete loss of engine power. My 2021 Ford Bronco is subject to recall 25S75 (NHTSA 25V455) for a low pressure fuel pump defect that can cause loss of fuel pressure or flow and engine stall. I was stranded on the side of the interstate in 100 degree heat with my newborn in the vehicle. This was a dangerous situation, not a minor inconvenience. I had the vehicle towed to an AAA Car Care Center in Charlotte, NC, where the fuel pump failure was diagnosed. AAA could not perform a repair because the issue falls under an open safety recall. I contacted the Ford Recall Assistance Center and was told no remedy is currently available for recall 25S75. I also visited Capital Ford Charlotte, who confirmed the same, that no remedy exists yet. With the vehicle inoperable and no repair available anywhere, I paid out of pocket for private transport to move the vehicle to my home in Newnan, GA, since Ford could not confirm coverage for towing to my home dealership. As of August 12, 2026, NHTSA materials still list the remedy for 25S75 as under development. My vehicle remains inoperable with no path to repair. This is now also preventing me from selling or trading the vehicle. A dealership (Buford Toyota) declined to even appraise it because it will not run. I am filing this complaint to document that an open, unremedied safety recall directly caused a vehicle failure that endangered myself and my infant child, and continues to leave the vehicle unusable and unsellable months later.
NHTSA ODI #11756704
Mileage unknown · Jun 16, 2026
Electrical System
Window actuator does not properly open or close passenger window to open door properly, which is a safety risks to a child. Window could shatter because window will not roll down the inch or so to pull the door open. In order to open the door, the window will shake vibrantly and risk of a child of a possible window shatter. Ford…
Read full complaint
Window actuator does not properly open or close passenger window to open door properly, which is a safety risks to a child. Window could shatter because window will not roll down the inch or so to pull the door open. In order to open the door, the window will shake vibrantly and risk of a child of a possible window shatter. Ford says this is a normal wear and tear and it’s at owners cost to replace. To me that’s unacceptable.
NHTSA ODI #11744621
Mileage unknown · May 4, 2026
Electrical SystemUnknown Or Other
I am submitting a safety complaint regarding my Ford vehicle’s infotainment screen failure, which has been identified under a recall but currently has no available remedy or repair timeline. When the screen goes blank or becomes unresponsive, I lose access to critical safety features, including the rearview camera, which is fed…
Read full complaint
I am submitting a safety complaint regarding my Ford vehicle’s infotainment screen failure, which has been identified under a recall but currently has no available remedy or repair timeline. When the screen goes blank or becomes unresponsive, I lose access to critical safety features, including the rearview camera, which is federally required. This significantly increases the risk of accidents while reversing, especially in areas with pedestrians. The system also affects access to navigation, hands-free communication, and important vehicle alerts, forcing me to either drive without these features or become distracted trying to compensate. Although Ford has acknowledged this issue, there is no clear timeline for a fix, and no accommodations have been provided. I am expected to continue driving a vehicle that does not meet expected safety standards, which puts both myself and others at risk. I rely on my vehicle daily, including transporting passengers, and the lack of a functioning safety system is a serious concern. The absence of communication and support from Ford regarding a resolution is also concerning. I respectfully request that NHTSA investigate this issue and require Ford to provide a timely remedy or appropriate accommodations, such as a loaner vehicle or interim solution, to ensure driver and public safety while awaiting a permanent fix.
NHTSA ODI #11735509
Mileage unknown · Apr 23, 2026
Electrical SystemForward Collision Avoidance
The digital gauge cluster where it shows sensitive information is a blacked out screen. I took it an automotive shop to investigate the issue. They ran a diagnositic and confirmed the screen is receiving power, fuses are good, but the screen is not powering up. I cannot view the digital speed, fuel gauge, mileage, access GOAT …
Read full complaint
The digital gauge cluster where it shows sensitive information is a blacked out screen. I took it an automotive shop to investigate the issue. They ran a diagnositic and confirmed the screen is receiving power, fuses are good, but the screen is not powering up. I cannot view the digital speed, fuel gauge, mileage, access GOAT modes, view tire pressure, view oil life, and other critical data, etc. This first occured a few months ago and would randomly turn back on, but not the screen is black more than it is on. Luckily I am able to track the fuel gauge (miles to empty) on the infotainment screen.
NHTSA ODI #11733378
28,000 miles · Jan 22, 2026
Electrical System
The contact owns a 2021 Ford Bronco. The contact stated that while driving at an undisclosed speed, the parking assist fault warning light illuminated. The vehicle was taken to the dealer, where it was diagnosed with a failed wiring harness. The contact was informed that a wire from the wiring harness was burned. In addition, th…
Read full complaint
The contact owns a 2021 Ford Bronco. The contact stated that while driving at an undisclosed speed, the parking assist fault warning light illuminated. The vehicle was taken to the dealer, where it was diagnosed with a failed wiring harness. The contact was informed that a wire from the wiring harness was burned. In addition, the contact was informed that if the wire continued burning it might start a fire. The vehicle was repaired. The contact was informed that the repair was not covered under warranty. The manufacturer was made aware of the failure, and a case was filed. The claim for the repair was denied. The failure mileage was approximately 28,000.
NHTSA ODI #11712776
Mileage unknown · Jan 21, 2026
Back Over PreventionElectrical SystemLane Departure
I received an alert on the dash stating there was an issue with the blind spot monitoring/rear cross traffic system. It was erroring off and on for that entire drive. When I got home, I googled the issue and it appears it's a known issue with '21 and some early '22 broncos where they factory installed the blind spot module wir…
Read full complaint
I received an alert on the dash stating there was an issue with the blind spot monitoring/rear cross traffic system. It was erroring off and on for that entire drive. When I got home, I googled the issue and it appears it's a known issue with '21 and some early '22 broncos where they factory installed the blind spot module wiring harness too close to the rear bumper. Over time, the wires rub and eventually rub bare and corrode or short out. I went out to take a look and sure enough, I had rubbed through on the driver side (photo) and the passenger side was nearly rubbed through. I have an extended warranty and it's at the dealership today. This is a manufacturing defect and should be covered (even if out of warranty) in my opinion. We will see what kind of story the dealer can come up with to wiggle out of it being covered under warranty.
NHTSA ODI #11712311
Mileage unknown · Jan 17, 2026
Back Over PreventionElectrical System
Bronco wire corrosion cross traffic refers to a known issue where wiring under the rear bumper, often for the blind spot/cross-traffic sensors, chafes, frays, and corrodes, causing system faults and failures, sometimes due to design flaws or environmental exposure to salt, requiring inspection and repair of the harness. This pro…
Read full complaint
Bronco wire corrosion cross traffic refers to a known issue where wiring under the rear bumper, often for the blind spot/cross-traffic sensors, chafes, frays, and corrodes, causing system faults and failures, sometimes due to design flaws or environmental exposure to salt, requiring inspection and repair of the harness. This problem triggers error messages like "Cross Traffic System/Blind Spot System Fault" in the instrument cluster, impacting safety features, with potential fixes involving harness repair, protective sheathing, or sensor replacement. My car’s wiring was corroded due to this flaw and required a repair exceeding $1,000.
NHTSA ODI #11711629
Mileage unknown · Dec 22, 2025
Back Over PreventionElectrical SystemLane Departure
Location of wiring from the factory for Blind Spot Warning and Cross Traffic Alert systems is not protected. The wiring has frayed and broken due to the wiring being unprotected, loose and rubbing on the rear bumper, causing the systems to not function. This is a blatant design defect from the factory, causing two safety system…
Read full complaint
Location of wiring from the factory for Blind Spot Warning and Cross Traffic Alert systems is not protected. The wiring has frayed and broken due to the wiring being unprotected, loose and rubbing on the rear bumper, causing the systems to not function. This is a blatant design defect from the factory, causing two safety systems to fail. Reporting now as, to the best of my knowledge, the manufacturer has not issued a TSB or recall and dealerships have acknowledged the issue.
NHTSA ODI #11706454
Mileage unknown · Nov 7, 2025
Electrical SystemVehicle Speed Control
I was driving on the highway at a speed of approximately 70 miles per hour when the Bronco driver screen gave multiple warning notices and at the same time, the accelerator would not react. Steering power was fine. I was in the second from far left lane on a six lane highway and losing speed quickly. I was able to move to the…
Read full complaint
I was driving on the highway at a speed of approximately 70 miles per hour when the Bronco driver screen gave multiple warning notices and at the same time, the accelerator would not react. Steering power was fine. I was in the second from far left lane on a six lane highway and losing speed quickly. I was able to move to the right and drift to the side of the road without incident. Once stopped, I turned the ignition off and waited a few seconds and then turned it back on again. The error messages all cleared and the Bronco accelerator reacted appropriately. I drove it straight to the dealership for inspection. They found the 210 connector was not making a good connection. They cleaned it and added electric grease and reconnected. Everything cleared and the connection was deemed good. I have not worked in the Bronco engine compartment or had work done that would have resulted in loosening the 210 connector. My understanding from the shop is that corrosion caused this connector to loosen.
NHTSA ODI #11698141
Mileage unknown · Aug 28, 2025
Back Over PreventionElectrical SystemLane Departure
I have been getting a message that my blind spot and cross traffic alert deactivated because trailer is attached. I have never had a trailer attached but do have a trailer hitch- the dealer said Ford refuses to pay to have it fixed because the bumper to bumper warranty is out. the car has been garaged and has only 9,000 miles …
Read full complaint
I have been getting a message that my blind spot and cross traffic alert deactivated because trailer is attached. I have never had a trailer attached but do have a trailer hitch- the dealer said Ford refuses to pay to have it fixed because the bumper to bumper warranty is out. the car has been garaged and has only 9,000 miles on it. This is a safety issue that I think they should cover as I have no blind spot or cross traffic warnings.
NHTSA ODI #11683687
Official recalls
20Jul 20, 2026
Ford Motor Company (Ford) is recalling certain 2021-2026 Bronco and Bronco Raptor vehicles. The engine compartment wiring harness may become damaged and short circuit.
Consequence & remedy
Consequence: A short circuit in the engine compartment can create heat or spark, increasing the risk of a fire.
Remedy: Dealers will install sheathing over the wiring, free of charge. This is a Phased campaign. Phase 1 will include 2026 Bronco Raptor notified owners on 7/31/2026. Phase 2 will include 2021-2025 Bronco Raptor vehicle will notify owners on or about 8/14/2026. Phase 3 will include 2021-2026 Bronco will notify owners on or about 9/1/2026. Owner notification letters were mailed August 5, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S55. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on July 23, 2026.
Additional source detail variants (2)
Engine
Ford Motor Company (Ford) is recalling certain 2021-2026 Bronco and Bronco Raptor vehicles. The engine compartment wiring harness may become damaged and short circuit.
Consequence: A short circuit in the engine compartment can create heat or spark, increasing the risk of a fire.
Remedy: Dealers will install sheathing over the wiring, free of charge. This is a Phased campaign. Phase 1 will include 2026 Bronco Raptor notified owners on 7/31/2026. Phase 2 will include 2021-2025 Bronco Raptor vehicle will notify owners on or about 8/14/2026. Phase 3 will include 2021-2026 Bronco will notify owners on or about 9/1/2026. Owner notification letters were mailed August 5, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S55. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on July 23, 2026.
Electrical System:wiring:front Underhood
Ford Motor Company (Ford) is recalling certain 2021-2026 Bronco and Bronco Raptor vehicles. The engine compartment wiring harness may become damaged and short circuit.
Consequence: A short circuit in the engine compartment can create heat or spark, increasing the risk of a fire.
Remedy: Dealers will install sheathing over the wiring, free of charge. This is a Phased campaign. Phase 1 will include 2026 Bronco Raptor notified owners on 7/31/2026. Phase 2 will include 2021-2025 Bronco Raptor vehicle will notify owners on or about 8/14/2026. Phase 3 will include 2021-2026 Bronco will notify owners on or about 9/1/2026. Owner notification letters were mailed August 5, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S55. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on July 23, 2026.
May 12, 2026
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The 3-door and 5-door Molded-In-Color (MIC) hardtop roof panels may have been manufactured improperly, which can allow sections of the outer roof panel to separate and detach from the vehicle.
Consequence & remedy
Consequence: A detached section of roof can create a road hazard, increasing the risk of a crash.
Remedy: Dealers will inspect and replace the hard top as necessary, free of charge. Interim letters, notifying owners of the safety risk were mailed May 28, 2026. Additional letters will be sent once the remedy is available, anticipated in November 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S32. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on May 12, 2026.
Apr 14, 2026
Ford Motor Company (Ford) is recalling certain 2021-2025 Bronco vehicles. The transmission to transfer case joint may be misaligned due to an incorrectly performed previous repair, which could lead to wear of the transmission output shaft splines and transfer case input splines.
Consequence & remedy
Consequence: Excessive wear of the transmission and transfer case splines may result in a loss of drive power or vehicle rollaway, increasing the risk of a crash.
Remedy: Dealers will inspect the transmission to transfer case joint and replace the transmission and transfer case as necessary, free of charge. Owner notification letters were mailed July 9, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S26. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on April 15, 2026.
Mar 3, 2026
Ford Motor Company (Ford) is recalling certain 2021-2026 Ford Bronco and 2021-2024 Ford Edge vehicles. The Accessory Protocol Interface Module (APIM) may overheat and shutdown, which can prevent the rearview camera image from displaying as intended.
Consequence & remedy
Consequence: A rearview camera that fails to display an image can reduce the driver’s view behind the vehicle, increasing the risk of a crash.
Remedy: The APIM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed April 13, 2026. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 26S09. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on March 5, 2026.
Dec 18, 2025
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were previously repaired incorrectly under recall number 23V165. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Consequence & remedy
Consequence: A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
Remedy: Dealer will update the SYNC module software ,free of charge. Owner notification letters were mailed January 28, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C72. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning January 30, 2026.
Oct 23, 2025
Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco vehicles. The front seats may have a loose or dislodged seat frame height-adjust pivot bolt.
Consequence & remedy
Consequence: A seat with a dislodged bolt may not properly restrain an occupant in a crash, increasing the risk of injury.
Remedy: Dealers will inspect and replace the pivot links and bolts as necessary, free of charge. Owner notification letters were mailed April 28, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SB5. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov beginning October 28, 2025.
Oct 10, 2025
Ford Motor Company (Ford) is recalling certain 2016-2019 Lincoln MKC, 2016-2023 Explorer, 2019-2020 Fusion, 2019-2024 Ranger, 2020-2022 Lincoln Corsair, Escape, 2021-2024 Bronco, Bronco Sport, and 2022-2024 Maverick vehicles. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Consequence & remedy
Consequence: An electrical short circuit can increase the risk of a fire.
Remedy: Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded blanking plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed December 3, 2025. Additional letters will be sent once the final remedy is available, anticipated September 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 15, 2025.
Jul 7, 2025
Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco, Explorer, Lincoln Aviator, F-250 SD, F-350 SD, F-450 SD, F-550 SD, 2021-2022 Lincoln Navigator, Mustang, F-150, and 2022 Expedition vehicles. The low-pressure fuel pump may fail, which can result in an engine stall while driving.
Consequence & remedy
Consequence: An engine stall increases the risk of a crash.
Remedy: Dealers will replace the low pressure fuel pump on super duty vehicles and update the powertrain control module (PCM) software on all other affected vehicles, free of charge. Owner notification letters were mailed July 27, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S75.
May 9, 2025
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were repaired incorrectly under recall 22V-825. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Consequence & remedy
Consequence: A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
Remedy: Dealers will update SYNC module software, free of charge. Owner notification letters were mailed June 18, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C14.
May 9, 2025
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to delay, freeze, or not display when the vehicle is in reverse.
Consequence & remedy
Consequence: A frozen or missing rearview camera image can reduce the driver's view behind the vehicle, increasing the risk of a crash.
Remedy: The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49.
Jan 17, 2025
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco vehicles. The rear shock absorbers may corrode and fail, resulting in detachment of the external reservoir.
Consequence & remedy
Consequence: An external reservoir that detaches from a vehicle can create a road hazard, increasing the risk of a crash.
Remedy: Dealers will replace the rear shock absorbers, as necessary free of charge. Owner notification letters were mailed August 15, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S01.
Aug 23, 2024
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco, F-150, Edge, Explorer, Lincoln Nautilus, and Lincoln Aviator vehicles equipped with either a 2.7L or 3.0L Nano EcoBoost engine. The engine intake valves may break while driving, which can result in engine failure and a loss of drive power.
Consequence & remedy
Consequence: A loss of drive power increases the risk of a crash.
Remedy: Dealers will perform an engine cycle test and replace the engine as necessary, free of charge. Owner notification letters were mailed July 3, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S55.
Aug 25, 2023
Ford Motor Company (Ford) is recalling certain 2020-2023 Lincoln Aviator, 2018-2021 Lincoln Navigator, 2022-2023 Ford Transit, and 2021 Ford Bronco vehicles. The rearview camera, or 360-degree view camera if equipped, may not display a rearview image when the vehicle is placed in reverse.
Consequence & remedy
Consequence: Loss of the rearview camera image can reduce the driver's rear visibility, increasing the risk of a crash.
Remedy: Dealers will replace the rearview camera, and update the software and wiring as necessary, free of charge. Owner notification letters were mailed November 20, 2023 to Lincoln owners. Ford vehicle owners notification letters were mailed March 4, 2024. Ford remedy parts are anticipated 2nd Quarter 2024. Ford's number for this recall is 23S48.
May 18, 2023
Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco vehicles built with the 5-Door body style. The first-row seat belt latch plates may be difficult to access from their stowed position. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."
Consequence & remedy
Consequence: Difficulty accessing the seat belt latches may result in occupants not wearing their seat belts, increasing the risk of injury in a crash.
Remedy: Dealers will add a sliding clip latch stop to the driver and front passenger seat belts, free of charge. Interim owner notification letters notifying owners of the safety risk were mailed July 14, 2023. Owner letters informing owners that parts are available were mailed on October 2, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C16.
Mar 10, 2023
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were previously remedied under recall 22V-825. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Consequence & remedy
Consequence: A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
Remedy: The SYNC module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on March 28, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C05.
Dec 14, 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The right or left side impact sensors may not be properly secured to the vehicle.
Consequence & remedy
Consequence: An improperly secured side impact sensor may cause the air bags to unintentionally deploy, or not to deploy as intended, increasing the risk of injury in a crash.
Remedy: Dealers will inspect the side impact sensor attachments and repair, as necessary, free of charge. Owner notification letters were mailed January 20, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S77.
Nov 3, 2022
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with rearview camera systems and 8-inch screen displays. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Consequence & remedy
Consequence: A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver, increasing the risk of a crash.
Remedy: The SYNC module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on March 25, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22C27.
Jun 10, 2022
Ford Motor Company (Ford) is recalling certain four-door 2021-2022 Bronco vehicles. The passenger-side rear door may be opened from inside of the vehicle when the child safety lock is in the "ON" position.
Consequence & remedy
Consequence: A malfunctioning child safety lock increases the risk of injury to a child occupant.
Remedy: Dealers will inspect the passenger-side child safety locks door child safety lock and latch, and replace them, if necessary, free of charge. Owner notification letters were mailed June 28, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S44.
Dec 16, 2021
Ford Motor Company (Ford) is recalling certain 2021 Ranger and Bronco vehicles. The cruise control radar module was misaligned during production.
Consequence & remedy
Consequence: A misaligned radar module may prevent the vehicle from maintaining a safe distance from other vehicles when adaptive cruise control is active. In addition, the automatic emergency braking (AEB) system may react slowly, or not react at all, during a pre-collision assist braking event. Any of these scenarios can increase the risk of a crash.
Remedy: Dealers will adjust the angle of the cruise control radar module, free of charge. Owner notification letters were mailed January 21, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S52.
Additional source detail variants (2)
Forward Collision Avoidance: Sensing System: Radar
Ford Motor Company (Ford) is recalling certain 2021 Ranger and Bronco vehicles. The cruise control radar module was misaligned during production.
Consequence: A misaligned radar module may prevent the vehicle from maintaining a safe distance from other vehicles when adaptive cruise control is active. In addition, the automatic emergency braking (AEB) system may react slowly, or not react at all, during a pre-collision assist braking event. Any of these scenarios can increase the risk of a crash.
Remedy: Dealers will adjust the angle of the cruise control radar module, free of charge. Owner notification letters were mailed January 21, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S52.
Forward Collision Avoidance: Automatic Emergency Braking
Ford Motor Company (Ford) is recalling certain 2021 Ranger and Bronco vehicles. The cruise control radar module was misaligned during production.
Consequence: A misaligned radar module may prevent the vehicle from maintaining a safe distance from other vehicles when adaptive cruise control is active. In addition, the automatic emergency braking (AEB) system may react slowly, or not react at all, during a pre-collision assist braking event. Any of these scenarios can increase the risk of a crash.
Remedy: Dealers will adjust the angle of the cruise control radar module, free of charge. Owner notification letters were mailed January 21, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S52.
Oct 1, 2021
Ford Motor Company (Ford) is recalling certain 2021 Bronco vehicles. During passenger air bag deployment, an air bag vent could open prematurely and result in an improper deployment. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."
Consequence & remedy
Consequence: Improper air bag deployment increases the risk of injury during a crash.
Remedy: Dealers will replace the passenger air bag, free of charge. An interim owner notification letter was mailed on November 24, 2021. A second notice announcing the remedy is available was sent on July 8, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C23.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4PE24019 · Low-pressure Fuel Pump Failure
Opened Jul 29, 2024 · Closed Sep 19, 2025
Status: closed (inferred from source dates) · Fuel System, Gasoline:delivery:fuel Pump
On July 29, 2024, the Office of Defects Investigation (ODI) opened PE24019 to investigate complaints of low-pressure fuel pump failures in MY 2021 Ford Bronco vehicles. Some consumers reported that the failure occurred without warning while driving, resulting in a complete loss of motive power with no ability to restart the engine. Ford determined that several other vehicle models contain low-pressure fuel pumps substantially similar to the 2021 Ford Bronco, including the 2022-2023 Ford Bronco, 2018-2023 Ford F-150, 2022-2023 Ford Expedition, 2019-2023 Lincoln Navigator, 2020-2023 Ford F-250-F-550, 2024 Ford Super Duty Chassis Cab, 2024-2025 Ford Ranger, 2020-2023 Ford Explorer, 2020-2023 Lincoln Aviator, and 2021-2025 Ford Mustang. ODI's investigation found that the affected vehicles may lose fuel pressure and flow from the fuel delivery module (consisting of a low-pressure fuel pump, jet pump, reservoir, and other parts) due to a low-pressure pump failure. This can cause the engine to stall while driving. The root cause is reduced internal clearance in the fuel pump, increasing friction and sensitivity to vapor lock. Fuel blockage from contamination inside the jet pump also contributed to the failure. Ford stated that the contamination source was unknown. On July 7, 2025, Ford filed recall 25V-455 for certain 2021-2023 Ford F-550 SD/F-450 SD/F-350 SD/F-250 SD, 2021-2022 Lincoln Navigator, 2021-2022 Ford Mustang, 2021-2022 Ford F-150, 2021-2023 Ford Explorer, 2022 Ford Expedition, and 2021-2023 Ford Bronco vehicles produced between July 1, 2021, and July 30, 2022. The recall also included certain 2021-2023 Lincoln Aviator produced between July 1, 2021, and December 21, 2022. Ford explained in its recall filingthat the production dates used for the recall were based on changes in the manufacturing process. Specifically, Ford determined that in June 2021, the supplier modified the jet pump manufacturing process, producing fuel pump chambers with a lower-than-specified internal clearance. In July 2022, the supplier implemented corrective actions to the manufacturing process by adding two additional vacuum pumps to reduce contamination during the production of the jet pump. ODI has identified approximately 1,000 reports involving vehicles covered in this investigation but excluded from recall 25V-455. However, even with such reports, these vehicles experienced comparatively lower failure rates than the vehicles that are subject to Recall 25V-455. Ford has explained that these vehicles were excluded from the recall population because they did not experience the manufacturing changes that prompted the recall. Specifically, according to Ford, vehicles built before July 1, 2021 (the recall production start date), were not affected by the supplier’s change to the jet pump manufacturing process. Even after closing this investigation, ODI will continue to monitor complaints for vehicles excluded from recall 25V-455 to consider whether they exhibit the same risks as the vehicles encompassed by the recall. The recall remedy is currently under development. In view of Ford’s recall action, ODI is closing this Preliminary Evaluation, but will continue to monitor the issue as a remedy is developed and implemented. ODI will take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
EA23002 · Loss Of Motive Power
Opened Sep 29, 2023 · Closed Oct 31, 2024
Status: closed (inferred from source dates) · Engine
On July 22, 2022, the Office of Defects Investigation (ODI) granted a Defect Petition (DP22001) and opened a Preliminary Evaluation (PE22007) to investigate allegations of loss of motive power in model year (MY) 2021 Ford Bronco vehicles equipped with 2.7L EcoBoost engines. Complainants were reporting sudden engine failure while driving resulting in a loss of motive power, often without the ability to restart. During PE22007, the cause of engine failure and loss of motive power in the subject vehicles was determined to be intake valve fracture, and the full scope of vehicles affected by the subject defect was identified as all MY 2021-2022 Ford and Lincoln models equipped with either the 2.7L or 3.0L EcoBoost engines, referred to as the “Nano” engine family. If an intake valve fractures in the subject engines, it may drop into the cylinder and contact the piston, often resulting in catastrophic engine damage. On September 29, 2023, PE22007 was upgraded to an Engineering Analysis (EA23002) to further investigate the subject defect across the full scope of affected vehicles. During EA23002, ODI visited Ford facilities to review technical information related to intake valve fracture in “Nano” engines, coordinated with NHTSA’s Vehicle Research and Testing Center (VRTC), and analyzed updated field data relating the subject defect. Forensic analysis of fractured intake valves demonstrated that the defective components exhibited “grinding burn” or out of specification hardness in the area of the keeper grooves. The presence of grinding burn is evidence that during the groove grinding phase of production, the temperature of the valve became sufficiently high to alter the microstructure of the material and is indicative that the valve supplier’s manufacturing processes were not within control specifications. Grinding burn results in a hard, brittle microstructure and high residual stresses toward the surface of the valve. Through normal engine loading, a valve with grinding burn will likely fracture at the area of highest vulnerability, which is the third keeper groove. In its response to the EA23002 Information Request (IR) letter, Ford provided evidence of 396 customer complaints (including field reports), 825 warranty claims, and 936 engine exchanges. When considering both ODI and manufacturer failure report data, there have been reports representing 1066 unique vehicles within the subject vehicle population. Analysis of the failure report data demonstrates that vehicles equipped with potentially defective intake valves were built within a production “spike period” of May 2021 – October 2021. The beginning of the spike period corresponds to a ramp up in production at the valve supplier manufacturing facility, and the end of the spike period aligns with the implementation of several mid-production process improvements and the decision to change the metal alloy used to produce intake valves from “Silchrome Lite” to “Silchrome 1”. Ford began investigating the subject defect in July 2021, determined the root cause, and took corrective measures for the new production vehicles. Analysis of the failure report data demonstrates that these corrective actions were successful in eliminating the risk of intake valve fracture for subject vehicles produced after October 2021. However, Ford did not take any field action to address vehicles produced during the spike period, and in the several months following the implementation of the production changes, a significant number of field failures continued to occur. It is Ford’s assessment that not all valves produced during the spike period are defective, and that failures associated with the subject defect occur at low time in service. Analysis of the failure report data demonstrates that the vast majority of failures have occurred before 20,000 miles with over half of all reported failures occurring before 5,000 miles. The rate of reported failures related to the subject defect has steadily decreased since November 2021. ODI coordinated with NHTSA’s National Center for Statistics and Analysis (NCSA) to conduct statistical analysis and predict the number of future failures associated with the subject defect. The results of this analysis, and the trends identified through the failure report data are generally consistent with Ford’s assessment that defective intake valves will likely fail at a low time in service and indicate that the majority of subject vehicles equipped with defective valves have already experienced a failure. On August 23, 2024, Ford submitted recall 24V635 for subject vehicles equipped with “Nano” engines and built within the production spike period identified above (total population 90,736 vehicles). The remedy includes an inspection at a Ford/Lincoln dealership where the lifetime engine cycles of the vehicle will be determined. If a vehicle does not meet a threshold for lifetime engine cycles, the dealership will conduct a high RPM engine cycle accumulation procedure, which aims to identify if the vehicle is equipped with defective intake valves. Any vehicle that fails the accumulation procedure will receive an engine replacement under the recall. In addition to recall 24V635, Ford has stated that it will launch customer satisfaction campaign 24N12, which will provide extended warranty coverage to the subject vehicles through the earlier of 10 years or 150,000 miles. In view of the recall action being taken by Ford, ODI is closing this Engineering Analysis. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE22007 · Loss Of Motive Power Due To Valve Intake Failure On Ford Bronco Vehicles.
Opened Jul 22, 2022 · Closed Oct 2, 2023
Status: closed (inferred from source dates) · Engine
The Office of Defects Investigation (ODI) received a petition dated March 16, 2022, requesting an investigation regarding allegations of defective intake valves in model year (MY) 2021 Ford Bronco vehicles equipped with the 2.7L Eco-boost (“Nano”) engines. The petitioner alleged these vehicles are experiencing loss of motive power at any highway speeds with no-restart as a result of catastrophic engine failures. To date ODI is aware of 42 submitted Vehicle Owner Questionnaires (VOQ’s) alleging a loss of motive power. On July 22, 2022, ODI opened a Preliminary Evaluation (PE22-007) to investigate allegations of stalling/loss of motive power on the subject vehicles. Upon receiving Ford’s Information Request (IR) response, ODI learned Ford was aware of 110 consumer complaints (including field reports), 125 warranty claims and 136 engine exchanges related to the 2021 Ford Bronco. Ford’s response indicated these failures are across the “Nano” engine family, which includes both the 2.7L and 3.0L EcoBoost engine variants with a total estimated population of 708,837 vehicles. Additionally, ODI became aware that the subject engines contained intake valves that were manufactured out of a specific alloy known as “Silchrome Lite”, which can become excessively hard and brittle if an over-temperature condition occurs during machining of the component. The overly brittle intake valve can fracture at the keeper grove causing the intake valve to freely contact the piston, resulting in catastrophic engine failure. A design modification was implemented in October 2021, which changed the intake valve material to a different alloy known as “Silchrome 1”, that is less susceptible to over-temperature during machine grinding. ODI is upgrading this PE to an Engineering Analysis (EA23-002) to better understand the failure mechanism identified by Ford and to ascertain the complete scope. To review the reports cited in the attached Closing Resume ODI Report Identification Number document, go to NHTSA.gov
DP22001 · Loss Of Motive Power
Opened May 27, 2022 · Closed Jul 28, 2022
Status: closed (inferred from source dates) · Engine
The Office of Defects Investigation (ODI) received three petitions on March 17, March 18, and March 29, 2022, which requested a defect investigation into an alleged defect of the valves on model year (MY) 2021 Ford Bronco vehicles equipped with the 2.7L Eco-boost engines. The petitioners alleged that MY 2021 Ford Broncos vehicles are experiencing loss of motive power at highway speeds with no-restart due to catastrophic engine failures.On May 27, 2022, ODI opened this Defect Petition to evaluate whether to grant or deny the petition.ODI has identified 26 Vehicle Owners Questionnaires (VOQs) that relate to the alleged defect in the subject vehicles. Based on ODI's review of the applicable materials, including VOQs, NHTSA has decided to grant the petition and open a Preliminary Evaluation (PE22-007) to assess the scope, frequency, and potential safety-related consequences of the alleged defect.Accordingly, this Defect Petition is closed.The ODI complaints cited above can be reviewed at NHTSA.gov under the following ODI numbers:11448171, 11448461, 11450659, 11450702, 11450737, 11450788, 11450871, 11450879, 11451158, 11451503, 11451957, 11452074, 11452692, 11453669, 11453933, 11454098, 11455294, 11456219, 11456713, 11459262,11460124, 11460125, 11461178, 11463199, 11463296, 11464516.
Illustration