NHTSA owner reports · September 18, 2026 snapshot.
Service Brakes, Hydraulic complaints
56 reportsClear category filterMileage unknown · Jul 17, 2007
Service Brakes, Hydraulic
I HAD THE REAR BRAKES FOR THE 1995 DODGE STRATUS REPLACED ON 3/01/2007 BECOUSE BRAKES WERE WORN OUT, AND HAVE SINCE THEN HAD THEM REPLACE 3 DIFFERENT TIMES. MECHANIC SHOP COULD NOT FIGURE OUT WHY. THEY REPLACED EVERYTHING AND BACK BRAKES WERE STILL LOCKING. I BOUGHT THIS CAR USED TO DO MY MAIL ROUTE ON 8/03/2006 FROM A US…
Read full complaint
I HAD THE REAR BRAKES FOR THE 1995 DODGE STRATUS REPLACED ON 3/01/2007 BECOUSE BRAKES WERE WORN OUT, AND HAVE SINCE THEN HAD THEM REPLACE 3 DIFFERENT TIMES. MECHANIC SHOP COULD NOT FIGURE OUT WHY. THEY REPLACED EVERYTHING AND BACK BRAKES WERE STILL LOCKING. I BOUGHT THIS CAR USED TO DO MY MAIL ROUTE ON 8/03/2006 FROM A USED CAR DEALER, AND DID NOT KNOW OF ANY RECALLS. ALSO, THE CAR SWERVED WHEN HITTING THE BRAKES. REPLACED BRAKE LINES, BRAKE SHOES, CYLENDERS, DRUMS AND SPRINGS. *AK
NHTSA ODI #10196632
52,000 miles · Mar 11, 2003
Service Brakes, Hydraulic
MY WIFE COMPLAINED OF BRAKE PEDAL TRAVEL FURTHER THAN NORMAL. UPON INVESTIGATION, I DISCOVERED THAT ONE OF THE BOLT STUDS THAT HOLDS THE MASTER CYLINDER TO THE POWER BRAKE BOOSTER WAS BROKEN OFF AND MISSING. THE MASTER CYLINDER WAS PUSHED OUT OF THE BOOSTER TO ABOUT A 30 DEGEREE ANGLE. THE REMAINING STUD WAS STILL IN PLACE BUT B…
Read full complaint
MY WIFE COMPLAINED OF BRAKE PEDAL TRAVEL FURTHER THAN NORMAL. UPON INVESTIGATION, I DISCOVERED THAT ONE OF THE BOLT STUDS THAT HOLDS THE MASTER CYLINDER TO THE POWER BRAKE BOOSTER WAS BROKEN OFF AND MISSING. THE MASTER CYLINDER WAS PUSHED OUT OF THE BOOSTER TO ABOUT A 30 DEGEREE ANGLE. THE REMAINING STUD WAS STILL IN PLACE BUT BENT BADLY TO ONE SIDE. IF THERE HAD BEEN A PANIC STOP REQUIRED, I FEEL THAT THE MASTER CYLINDER COULD HAVE SEPARATED FROM THE BOOSTER, WITH THE EFFECT OF HAVING NO BRAKING EFFECTIVENESS. THIS COULD HAVE RESULTED IN A SERIOUS ACCIDENT OR FATALITY.*JB
NHTSA ODI #10010310
Mileage unknown · Sep 5, 2002
Service Brakes, Hydraulic
CONSUMER STATES THAT BRAKES DO NOT STOP VEHICLE EFFECTIVELY. CONSUMER ADVISED THAT WHILE DRIVING BRAKES PEDAL BECOMES LOOSER AND LOOSER. IF CONSUMER BRAKES, PEDAL GOES TO THE FLOOR, BUT VEHICLE DOES NOT COMPLETELY STOP.*JB
NHTSA ODI #8018025
Mileage unknown · May 24, 2002
Service Brakes, Hydraulic
WHILE DRIVING ABS BRAKE COMPUTER FAILED, CAUSING VEHICLE TO HAVE NO BRAKES.*AK
NHTSA ODI #8010467
Mileage unknown · Dec 8, 2001
Service Brakes, Hydraulic
THE CAR WAS STOPPING NORMALLY ON CLEAN DRY PAVEMENT FROM 35 MPH AND WHEN SLOWED TO ABOUT 25 MPH THE BRAKE PEDAL DROPPED APPROXIMATLY .25 INCHES A WHIRRING NOISE CAME FROM UNDER THE HOOD AND THE BRAKES SEEMED TO TOTALLY FREE WHEEL. I PUMPED THE BRAKES TO NO AVAIL AND STEPPED ON THE BRAKE PEDAL AS HARD AS I COULD AND THE CAR CONT…
Read full complaint
THE CAR WAS STOPPING NORMALLY ON CLEAN DRY PAVEMENT FROM 35 MPH AND WHEN SLOWED TO ABOUT 25 MPH THE BRAKE PEDAL DROPPED APPROXIMATLY .25 INCHES A WHIRRING NOISE CAME FROM UNDER THE HOOD AND THE BRAKES SEEMED TO TOTALLY FREE WHEEL. I PUMPED THE BRAKES TO NO AVAIL AND STEPPED ON THE BRAKE PEDAL AS HARD AS I COULD AND THE CAR CONTINUED TO ROLL WITH NO APPARENT BRAKING. I LOOKED AT THE DASH AND NO WARNING LIGHTS WERE LIT . AFTER I CAREFULLY LIMPED HOME WITH ONE HAND ON THE PARKING BRAKE I CHECKED THE FLUID AND IT WAS NORMAL.*AK
NHTSA ODI #755429
Mileage unknown · Oct 26, 2001
Service Brakes, Hydraulic
WITH STEADY PRESSURE ON THE BRAKE PEDAL AT STOP LIGHT,THE PEDAL WILL SLOWLY SINK TO THE FLOORBOARD AND BRAKES WILL GO AWAY AND CAR WILL ROLL AS IF THERE WERE NO BRAKES APPLIED. I HAVE NOT CONTACTED DEALER SERVICE CENTER YET. *AK
NHTSA ODI #753738
Mileage unknown · May 16, 2001
Service Brakes, HydraulicCrashInjury
BRAKES LOCKED ON LEFT SIDE OF CAR WHEN COMING TO A STOP. *AK
NHTSA ODI #745428
Mileage unknown · Apr 17, 2001
Electrical SystemEngine And Engine CoolingEquipment
1. A/C PAST 3 TEARS HAS FAILED. CONTROL MODE FAILURE. A/C REPAIRED 2X IN WARRENTY. 2. ABS SENSOR FAILED AT 42000. 3.DISTRIBUTOR FAILED AT 90000 3. TRANSMISSION-FRONT PUMP SEAL STARTED LEAKING AT 90000. 4. SPARK PLUG RING SEALS(6) FAILED AT 90000.
NHTSA ODI #744170
Mileage unknown · Oct 24, 2000
Service Brakes, HydraulicInjury
POSSIBLE BRAKE LOSS, TRYING TO FIND OUT IF THIS CAR HAD THE RECALL COMPLETED. *AK
NHTSA ODI #735042
Mileage unknown · Sep 11, 2000
Service Brakes, HydraulicSteering
FALSE DASH SIGNALS DISPLAYED THAT BRAKE SYSTEM WAS OUT OF ORDER. *SLC
NHTSA ODI #554496
Official recalls
7Jan 13, 2004
ON CERTAIN PASSENGER VEHICLES, THE FLOOR SHIFTER IGNITION-PARK INTERLOCK MAY FAIL AND ALLOW THE SHIFTER TO BE MOVED OUT OF THE PARK POSITION WITH THE KEY REMOVED. AN INOPERATIVE INTERLOCK MAY ALSO ALLOW THE KEY TO BE REMOVED WHEN THE SHIFTER HAS NOT BEEN PLACED IN THE PARK POSITION.
Consequence & remedy
Consequence: EITHER CIRCUMSTANCE MAY RESULT IN THE VEHICLE ROLLING AWAY WITHOUT WARNING.
Remedy: DEALERS WILL INSTALL A NEW LOAD-LIMITING PUSH ROD INTO THE FLOOR SHIFTER LEVER OF THE AFFECTED VEHICLES. OWNER NOTIFICATION BEGAN ON JUNE 14, 2004. OWNERS SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
Aug 6, 1998
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS. THE ADJUSTMENT OF THE CABLE CONNECTING THE CONSOLE SHIFTER MECHANISM TO THE IGNITION KEY CAN CAUSE A TRAPPED KEY CONDITION WHICH CAN RESULT IN A LOW FORCE REQUIRED TO DEPRESS THE SHIFT BUTTON. A COMBINATION OF APPLYING A MIS-ADJUSTED RELEASE BUTTON WITH A LOW FORCE ATTEMPT TO SHIFT OUT OF PARK WITH THE KEY IN THE LOCKED POSITION, CAN BREAK THE CONNECTING PIN IN THE SHIFTER.
Consequence & remedy
Consequence: IF THIS HAPPENS, THE "IGNITION-PARK" INTERLOCK SYSTEM WILL BE NONFUNCTIONAL.
Remedy: DEALERS WILL INSPECT FOR PROPER OPERATION OF THE SYSTEM. ANY VEHICLES THAT ARE NOT FUNCTIONAL AFTER THE INSPECTION WILL HAVE THE SHIFT MECHANISM AND CABLE REPLACED WITH A "SELF-ADJUSTING" DESIGN.
Mar 20, 1998
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE REAR SEAT BELT ANCHOR DOES NOT ACHIEVE THE LOADING REQUIRED BY FMVSS NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES."
Consequence & remedy
Consequence: FAILURE OF A SEAT BELT ANCHOR CAN RESULT IN THE LOSS OF SEAT BELT PROTECTION, WHICH COULD LEAD TO SERIOUS INJURY OR DEATH IN THE EVENT OF A CRASH.
Remedy: DEALERS WILL INSPECT THE REAR SEAT BELT OUTBOARD ANCHOR FLOOR ATTACHMENTS FOR PROPER POSITIONING. IF THE ANCHOR WAS IMPROPERLY ORIENTED, THE ORIENTATION WILL BE CORRECTED.
Nov 13, 1997
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LOWER CONTROL ARM BALL JOINT CAN SEPARATE DUE TO LOSS OF LUBRICATION.
Consequence & remedy
Consequence: SEPARATION OF THE BALL JOINT COULD CAUSE A LOSS OF STEERING CONTROL INCREASING THE RISK OF A VEHICLE CRASH.
Remedy: DEALERS WILL INSPECT THE BALL JOINT END HOUSING COVER SEAL FOR LEAKAGE WITH A HIGH PRESSURE AIR TESTER AND THE RUBBER BOOT WILL BE VISUALLY INSPECTED FOR DAMAGE. IF THE COVER SEAL LEAKS OR THE BOOT IS DAMAGED, THE LOWER CONTROL ARM WILL BE REPLACED.
May 3, 1996
THE BRAKE MASTER CYLINDER CAN LEAK BRAKE FLUID DUE TO A DAMAGED DOUBLE LIP REAR PISTON SEAL.
Consequence & remedy
Consequence: BRAKE FLUID LEAKAGE CAN RESULT IN DIMINISHED EFFECTIVENESS OF ONE HALF OF THE SPLIT BRAKE SYSTEM. THE INSTRUMENT PANEL WARNING LIGHT(S) WILL SIGNAL SYSTEM IMPAIRMENT PRIOR TO PARTIAL BRAKE SYSTEM LOSS.
Remedy: DEALERS WILL REPLACE THE REAR BRAKE MASTER CYLINDR PISTON ASSEMBLY.
May 2, 1996
CORROSION OF THE ABS HYDRAULIC CONTROL UNIT CAN CAUSE THE SOLENOID VALVES TO STICK IN THE OPEN POSITION.
Consequence & remedy
Consequence: IF EITHER FRONT WHEEL VALVE STICKS, THE VEHICLE WOULD SWERVE FROM A STRAIGHT STOP WHEN THE BRAKES ARE APPLIED.
Remedy: DEALERS WILL INSTALL A PLATE AND SILICONE GREASE INJECTED INTO THE SOLENOID CAVITY TO ELIMINATE THE POTENTIAL FOR THIS CONDITION.
Jan 11, 1996
IN CERTAIN VEHICLES, THE ENGINE CYLINDER HEAD OIL GALLEY PLUG DOES NOT SEAL PROPERLY AND ENGINE CYLINDER HEAD OIL IS NOT ADEQUATELY RETAINED.
Consequence & remedy
Consequence: INADEQUATE SEALING AND RETENTION OF THE PLUG CAN RESULT IN OIL LEAKAGE WHICH COULD CAUSE A FIRE IN THE ENGINE COMPARTMENT.
Remedy: DEALERS WILL INSTALL AN EXPANSION PLUG AND RETAINING BRACKET OVER THE CYLINDER HEAD OIL GALLEY PLUG.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
5EA03011 · Auto Trans IGNITION-PARK Interlock
Opened Jul 17, 2003 · Closed Jan 30, 2004
Status: closed (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:lever And Linkage:floor Shift
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
Additional source detail variants (2)
Power Train:automatic Transmission
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
Power Train:automatic Transmission:lever And Linkage:floor Shift
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
DP03002 · Steering Column Separation
Opened May 7, 2003 · Closed Jul 22, 2003
Status: closed (inferred from source dates) · Steering:column
MR. LARRY A. SACKEY SUBMITTED A PETITION TO THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION (NHTSA) BY LETTER DATED APRIL 18, 2003, REQUESTING THAT NHTSAFURTHER INVESTIGATE THE DEFECTIVE COLLAPSIBLE STEERING SHAFT SYSTEM ON 1987-1995 VEHICLES MANUFACTURED BY THE DAIMLERCHRYSLER CORPORATION.IN PART BECAUSE OF 49 CFR ? 30120(G), NHTSA HAS DECIDED TO LIMIT THE SCOPE OF THE PETITION VEHICLES TO 1993-1995 MODELS, EXCLUDING THE 1993 JEEP GRAND CHEROKEE AND 1994-1995 DODGE RAM SERIES TRUCKS THAT WERE RECALLED (93V210 & 96V230) FOR STEERING COLUMN FAILURE.IF THE ANALYSIS OF THESE VEHICLES HAD IDENTIFIED A POTENTIAL PROBLEM, THE SCOPE COULD HAVE BEEN EXPANDED IN AN INVESTIGATION.A REVIEW OF ODI'S DATA BASE SHOWS NO RECENT COMPLAINTS AND A LACK OF A COMPLAINT TREND CONCERNING THE SUBJECT ISSUE ON THE SUBJECT VEHICLES AS A WHOLE OR BY INDIVIDUAL MODELS.THEREFORE, THE PETITION IS DENIED.FOR DETAILS, SEE FEDERAL REGISTER NOTICE VOLUME 68, NO. 130, JULY 8, 2003.
PE02082 · Safety Belt Cinching Latch Plate
Opened Nov 6, 2002 · Closed Apr 23, 2003
Status: closed (inferred from source dates) · Seat Belts
THERE ARE NO INJURIES OR FATALITIES ASSOCIATED WITH THIS ALLEGED DEFECT.WHILE CONDUCTING THIS INVESTIGATION, ODI FOUND THAT THE SUBJECT CINCHES MEET THE LOAD BEARING REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD 208, AND THAT MANY OF THE REPORTED FAILURES WERE DUE TO INCORRECT CHILD SAFETY SEAT INSTALLATIONS. ADDITIONALLY, THE REPORT RATE IS LOW (1.60/100K).THE INFORMATION AVAILABLE FAILS TO ESTABLISH THE EXISTENCE OF A DEFECT TREND AT THIS TIME.FURTHER ALLOCATION OF AGENCY RESOURCES TO THIS ISSUE IS UNWARRANTED AND THE PRELIMINARY EVALUATION IS BEING CLOSED.
EA97016 · Lower Control Arm Ball Joint Failure
Opened Sep 29, 1997 · Closed Nov 20, 1997
Status: closed (inferred from source dates) · Suspension
BY LETTER DATED NOVEMBER 6, 1997, THE MANUFACTURER ADVISED THIS AGENCY OF ITS DECISION TO INITIATE A SAFETY RECALL CAMPAIGN OF THE SUBJECT VEHICLES TO CORRECT THE DEFECT IDENTIFIED IN THIS EA.THE RECALL WILL ALSO COVER 1996 AND 1997 CHRYSLER CIRRUS/DODGE STRATUS VEHICLES, AS WELL AS 1995 THROUGH 1997 CHRYSLER SEBRING CONVERTIBLE AND PLYMOUTH BREEZE VEHICLES EQUIPPED WITH IDENTICAL LOWER CONTROL ARM BALL JOINTS.AN ESTIMATED TOTAL OF 599,00VEHICLES ARE AFFECTED BY THIS RECALL.THE MANUFACTURER'S INVESTIGATION DISCLOSED THAT PROCESS VARIABILITY, TOGETHER WITH THE BALL JOINT HOUSING COVER CRIMPING OPERATION, CAN RESULT IN AN INEFFECTIVE SEAL THAT PERMITS A LOSS OF LUBRICATION AND ACCELERTED WEAR OF THE BALL JOINT ASSEMBLY.THIS CONDITION CAN LEAD TO FAILURE AND SEPARTION OF THE LOWER CONTROL ARM BALL JOINT.THE RECALL IS IDENTIFIED AS NHTSA 97V-201 AND A COPY OF CHRYSLER'S LETTER TO NHTSA IS ATTACHED HERETO.
PE97009 · Lower Control Arm Ball Joint Failure
Opened Mar 13, 1997 · Closed Sep 29, 1997
Status: closed (inferred from source dates) · Suspension
THE MANUFACTURER IDENTIFED VEHICLE OWNER COMPLAINTS OF THE SUBJECT BALL JOINT FAILURES AS TABULATED ABOVE.IN ADDITION, A TOTAL OF 72 WARRANTY REPORTS WERE IDENTIFIED FOR REPLACEMENT OF BROKEN OR CRACKED BALL JOINT ASSEMBLIES IN THE SUBJECT VEHICLES.CHRYSLER ALSO REPORTED THAT 1996 AND 1997 MODELS ARE EQUIPPED WITH IDENTICAL BALL JOINT ASSEMBLIES AS THE SUBJECT 1995 MODEL YEAR VEHICLES.A PARTIAL RESPONSE TO NHTSA'S INFORMATION REQUEST INDICATED THAT THE MANUFACTURER'S ANALYSES AND EVALUATIONS OF THE CONDITION WERE CONTINUING.IN ORDER TO CONTINUE NHTSA'S COMPLETE ASSESSMENT OF THE NATURE AND SCOPE OF THIS MATTER, THIS INVESTIGATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS.
Illustration