← New search

2008 Dodge RAM 2500

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2008 Dodge RAM 2500 do not stand out strongly from the model-year median of 275.

About this comparison →

When problems were reported

Mileage at the reported incident

227 reports with mileage · 90 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Steering. Review the 175 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Suspension. Review the 48 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Air Bags. Review the 30 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

12 crash reports8 fire reports7 injury reports

What owners actually said

317 reports
60,608 miles · Dec 22, 2015
Steering

TL* THE CONTACT OWNS A 2008 DODGE RAM 2500. WHILE DRIVING APPROXIMATELY 60 MPH, THERE WAS AN ABNORMAL NOISE COMING FROM THE VEHICLE AND THE STEERING WHEEL SEIZED WITHOUT WARNING. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE IT WAS DIAGNOSED THAT THE STEERING ASSEMBLY NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED.…

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE RAM 2500. WHILE DRIVING APPROXIMATELY 60 MPH, THERE WAS AN ABNORMAL NOISE COMING FROM THE VEHICLE AND THE STEERING WHEEL SEIZED WITHOUT WARNING. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE IT WAS DIAGNOSED THAT THE STEERING ASSEMBLY NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE VIN WAS INCLUDED IN NHTSA CAMPAIGN NUMBER: 13V528000 (STEERING). THE FAILURE MILEAGE WAS 60,608. UPDATED 02/12/16*LJ ACCORDING TO THE INVOICE, THE LOWER FRONT BALL JOINT, STEERING DAMPER AND INNER AND OUTER TIE ROD ENDS WERE REPLACED. UPDATED 02/25/16.*JB

NHTSA ODI #10811678

Mileage unknown · Dec 17, 2015
Air Bags

TL* TAKATA RECALL. THE CONTACT OWNS A 2008 DODGE RAM 2500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 15V313000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOT NOTIFIED OF…

Read full complaint

TL* TAKATA RECALL. THE CONTACT OWNS A 2008 DODGE RAM 2500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 15V313000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOT NOTIFIED OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE. UPDATED 03/11/16*LJ THE CONSUMER STATED THE VEHICLE WAS FIXED ON JUL 9, 2015. UPDATED 03/16/16. *JB

NHTSA ODI #10810962

45,000 miles · Dec 15, 2015
Engine

TL* TAKATA RECALL. THE CONTACT OWNS A 2008 DODGE RAM 2500. THE CONTACT STATED THAT WHEN THE VEHICLE WAS STARTED, THE ENGINE WARNING INDICATOR WAS INTERMITTENTLY ILLUMINATED. THE FAILURE RECURRED ON SEVERAL OCCASIONS UNTIL THE ENGINE WARNING INDICATOR WAS CONSISTENTLY ILLUMINATED EACH TIME THE VEHICLE WAS DRIVEN. THE VEHICLE WAS …

Read full complaint

TL* TAKATA RECALL. THE CONTACT OWNS A 2008 DODGE RAM 2500. THE CONTACT STATED THAT WHEN THE VEHICLE WAS STARTED, THE ENGINE WARNING INDICATOR WAS INTERMITTENTLY ILLUMINATED. THE FAILURE RECURRED ON SEVERAL OCCASIONS UNTIL THE ENGINE WARNING INDICATOR WAS CONSISTENTLY ILLUMINATED EACH TIME THE VEHICLE WAS DRIVEN. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC BUT THE FAILURE WAS UNABLE TO BE DETERMINED. THE VEHICLE WAS NOT REPAIRED. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 15V313000 (AIR BAGS), HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOT MADE AWARE OF THE ISSUE. THE APPROXIMATE FAILURE MILEAGE WAS 45,000. PARTS DISTRIBUTION DISCONNECT.

NHTSA ODI #10810207

125,000 miles · Dec 9, 2015
Electrical SystemVisibility/wiper

THE AIR CONDITIONER/HEATER BLOWER IN MY TRUCK HAS BEEN WORKING INTERMITTENTLY, BUT GETTING WORSE TO THE POINT THAT IT RARELY WORKS NOW. I TOOK IT TO A SHOP A FEW WEEKS AGO, BUT THE SYSTEM HAPPENED TO WORK THAT DAY AND THEY COULD NOT FIND ANY ISSUES. HOWEVER, I DID SOME RESEARCH ON THE INTERNET AND THERE ARE MANY OTHER OWNERS H…

Read full complaint

THE AIR CONDITIONER/HEATER BLOWER IN MY TRUCK HAS BEEN WORKING INTERMITTENTLY, BUT GETTING WORSE TO THE POINT THAT IT RARELY WORKS NOW. I TOOK IT TO A SHOP A FEW WEEKS AGO, BUT THE SYSTEM HAPPENED TO WORK THAT DAY AND THEY COULD NOT FIND ANY ISSUES. HOWEVER, I DID SOME RESEARCH ON THE INTERNET AND THERE ARE MANY OTHER OWNERS HAVING THIS PROBLEM. THE CAUSE IS A FAULTY IGNITION SWITCH/WIRING HARNESS CONNECTOR WHICH ACTUALLY MELTS FROM THE HEAT CAUSED BY IMPROPER WIRE GAUGE/DESIGN. THIS INFORMATION CAN BE READILY FOUND ON DODGE TRUCK FORUMS BY DOING A GOOGLE SEARCH. THERE WAS A PREVIOUS RECALL FOR THIS ISSUE ON EARLIER MODEL YEARS (SAFETY RECALL #875 ACCORDING TO ONE SITE) BUT NONE THAT I COULD FIND FOR MY MODEL YEAR. THIS IS A SAFETY ISSUE AS VISIBILITY COULD BE REDUCED BY FROST OR FOGGING OF THE WINDSHIELD SINCE THE WINDSHIELD DEFROSTER WILL NOT WORK. MOREOVER, FAILURE OF THE VEHICLE'S HEATER COULD BE A SAFETY ISSUE IN VERY COLD WEATHER--ESPECIALLY IN REMOTE LOCATIONS. IT MAY ALSO BE POSSIBLE FOR THE OVERHEATED/MELTED CONNECTORS/COMPONENTS TO CAUSE A FIRE OR TO MANIFEST OTHER FAILURES ASSOCIATED WITH THE IGNITION SWITCH (UNCOMMANDED ENGINE CUTOFF, ETC.). THANK YOU IN ADVANCE FOR INVESTIGATING THIS ISSUE. *TR

NHTSA ODI #10809199

Mileage unknown · Dec 4, 2015
Air Bags

TL* TAKATA RECALL. THE CONTACT OWNS A 2008 DODGE RAM 2500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 15V313000 (AIR BAGS) HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOT NOTIFIED OF …

Read full complaint

TL* TAKATA RECALL. THE CONTACT OWNS A 2008 DODGE RAM 2500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 15V313000 (AIR BAGS) HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOT NOTIFIED OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT. UPDATED 02/19/16*LJ UPDATED 02/23/16.*JB

NHTSA ODI #10808467

Mileage unknown · Dec 1, 2015
Power TrainSteeringVehicle Speed Control

STEERING RECALL- VEHICLE INITIATES INTO THE DEATH SHAKE WHEN SPEED EXCEEDS 55MPH ON A TURN. TRANSMISSION PROBLEMS- VEHICLE HAS PROBLEMS SHIFTING NORMALLY BY SHIFTING STRAIGHT INTO 4TH GEAR WHEN SHIFTING INTO DRIVE AND WILL DRIVE SLUGGISHLY

NHTSA ODI #10807878

93,000 miles · Nov 25, 2015
Tires

ON SAT. 11/21/15 I WAS DRIVING EAST ON I-80 AT MARTIS VALLEY IN TRUCKEE, CA. SUDDENLY, I FELT A VIBRATION IN THE FRONT END. AS I SLOWED TO MERGE INTO THE RIGHT LANE, SO THAT I COULD PULL OVER, THE RIGHT FRONT TIRE BLOWS TO PIECES, MY TRUCK LUNGES INTO THE RIGHT LANE, NARROWLY MISSING A SUBARU, AND I FINALLY GET SAFELY PULLED OVE…

Read full complaint

ON SAT. 11/21/15 I WAS DRIVING EAST ON I-80 AT MARTIS VALLEY IN TRUCKEE, CA. SUDDENLY, I FELT A VIBRATION IN THE FRONT END. AS I SLOWED TO MERGE INTO THE RIGHT LANE, SO THAT I COULD PULL OVER, THE RIGHT FRONT TIRE BLOWS TO PIECES, MY TRUCK LUNGES INTO THE RIGHT LANE, NARROWLY MISSING A SUBARU, AND I FINALLY GET SAFELY PULLED OVER. THE TIRES, BFG KO2 ALL TERRAIN, ARE BRAND NEW, LESS THAN 1000 MILES ON THEM. COST ME $2200.00, BOUGHT THEM 2 WEEKS EARLIER FROM DISCOUNT TIRE IN RENO, NV. UPON FURTHER INVESTIGATION INTO BFG TIRES, I HAVE FOUND OVER 150 COMPLAINTS, JUST IN THE PAST SIX MOS., OF EITHER THE SAME BLOWOUT THAT HAPPENED TO ME, OR THE TREAD OF THE TIRE PEELING OFF COMPLETELY. SOME PEOPLE HAVE HAD SIGNIFICANT PROPERTY DAMAGE COMPARED TO THE DAMAGE THAT MY TRUCK ENDURED. THIS MAY HAVE SOMETHING TO DO WITH THE TIRES BEING ON 3/4 AND 1 TON TRUCKS, AS THE CYCLE OF "MOST" OF THE COMPLAINTS ARE PEOPLE THAT DRIVE THESE VEHICLES. BFG THEN TELLS THE CONSUMER THAT THEY NEED THE TIRE TO DETERMINE WHY THE TIRE FAILED. THEN AFTER THEY GET THE TIRE THEY DENY THE CONSUMERS CLAIM, AND TELL THEM THAT THE TIRE FAILED BECAUSE OF SOMETHING THE CONSUMER HAD DONE, I.E. LOW TIRE PRESSURE, STRUCK SOMETHING, ECT... SEEMS TO BE THE SAME STORY OVER AND OVER. I HAVE NEW TIRES ON ORDER, SOME NITTO'S. NEVER TRIED THEM, BUT I HAVE A LOT OF BUDDIES THAT RUN THEM. I HOPE THAT THIS COMPLAINT WILL BE INVESTIGATED BEFORE SOMEBODY CAUSES A BAD ACCIDENT. I HAVE THE SHREDDED TIRE THAT I WAS HOPING TO SEND TO YOU GUYS TO SEE IF YOU COULD DETERMINE THE CAUSE OF THE BLOWOUT. THANK YOU *TR

NHTSA ODI #10806756

15 miles · Nov 13, 2015
SteeringWheels

TL* THE CONTACT OWNS A 2008 DODGE RAM 2500. WHILE DRIVING AT 50 MPH, THE VEHICLE SHOOK. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE STEERING WHEEL, TIE RODS AND OTHER UNKNOWN PARTS NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED HOWEVER, THE FAILURE RECURRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAIL…

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE RAM 2500. WHILE DRIVING AT 50 MPH, THE VEHICLE SHOOK. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE STEERING WHEEL, TIE RODS AND OTHER UNKNOWN PARTS NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED HOWEVER, THE FAILURE RECURRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 15.

NHTSA ODI #10790281

249,215 miles · Nov 7, 2015
Steering

MANY REFER TO IT AS THE "DEATH WOBBLE" AND IT HAS DONE IT AT LEAST ONCE EVERY TIME I DRIVE I HAVE EXPERIENCED THE DEATH WOBBLE ON THE HIGHWAY WHILE GOING 75 MPH AND IT CAUSES ME TO HAVE TO SLOW DOWN DRASTICALLY. I AM NOT ONLY WORRIED FOR MY WELLNESS/LIFE BUT MY FAMILY MEMBERS AS WELL. THIS VEHICLE IS USED AS A DAILY DRIVER.

NHTSA ODI #10788982

100,000 miles · Nov 4, 2015
SteeringSuspension

VEHICLE WANDERS WHEN DRIVING HAD 2 FRONT END ALIGNMENTS AND TIRES BALANCED HAS NOT CORRECTED PROBLEM. HAD IT REINSPECTED AND LEFT TIE ROD END WORN. WAS TOLD IT DOES NOT COME UNDER RECALL FOR STEERING LINKAGE.

NHTSA ODI #10788213

Official recalls

7

16V352000 · Air Bags:frontal:passenger Side:inflator Module

May 24, 2016

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Consequence & remedy

Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

15V313000 · Air Bags:frontal:driver Side:inflator Module

May 26, 2015

Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.

13V528000 · Steering:linkages:tie Rod Assembly

Nov 6, 2013

Chrysler Group LLC (Chrysler) is recalling certain model year 2003-2008 Dodge RAM 2500 4x4 and 3500 4x4, model year 2007-2008 Dodge RAM 3500 4x2 Cab Chassis and model year 2006-2008 Dodge RAM 1500 Mega Cab 4x4 trucks manufactured February 12, 2002, through February 13, 2008. The left tie rod assembly may break.

Consequence & remedy

Consequence: A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.

Remedy: Chrysler notified owners and launched its recall campaign in January 2014. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N62.

13V529000 · Steering:linkages:tie Rod Assembly

Nov 6, 2013

Chrysler Group LLC (Chrysler) is recalling certain model year 2008-2012 RAM 2500 4X4 and 3500 4X4 trucks, 2008-2012 Dodge RAM 3500 4x2 Cab Chassis, and model year 2008 Dodge RAM 1500 Mega Cab 4x4. The left tie rod assembly may break.

Consequence & remedy

Consequence: A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.

Remedy: Chrysler notified owners on January 16, 2014 that dealers would inspect vehicles and replace the steering linkage assembly, if necessary. On or about February 27, 2014, Chrysler ceased its recall remedy program due to parts quality concerns, and then re-initiated it on or about April 14, 2014. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N49.

11V350000 · Steering:linkages:tie Rod Assembly

Jul 6, 2011

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2008-2011 DODGE RAM 2500/3500 4X4, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH MARCH 28, 2011; MODEL YEAR 2008-2011 DODGE RAM 3500 CAB CHASSIS 4X2, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH MARCH 28, 2011; AND MODEL YEAR 2008 DODGE RAM 1500 MEGA CAB 4X4, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH AUGUST 15, 2008, BECAUSE THE LEFT TIE ROD BALL STUD MAY FRACTURE. THIS CONDITION TENDS TO OCCUR DURING LOW SPEED PARKING LOT TYPE MANEUVERS WHEN THE CUSTOMER IS MAKING A TIGHT TURN. ADDITIONALLY, MODEL YEAR 2003-2008 DODGE RAM 2500/3500 VEHICLES MAY HAVE RECEIVED THE AFFECTED TIE ROD ASSEMBLY AS A REPLACEMENT PART DURING NORMAL SERVICE.

Consequence & remedy

Consequence: THIS CONDITION COULD RESULT IN THE POTENTIAL LOSS OF DIRECTIONAL STABILITY IN THE LEFT HAND FRONT WHEEL, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE TIE ROD ENDS FOR RELATIVE ORIENTATION AND REPLACE THE LEFT OUTER TIE ROD AS REQUIRED AND PERFORM A FRONT END TOE ALIGNMENT AS NEEDED. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 3, 2011. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

09V005000 · Steering:linkages:tie Rod Assembly

Jan 9, 2009

CHRYSLER IS RECALLING 32,782 MY 2008-2009 DODGE RAM 2500, 3500 AND 3500 CAB CHASSIS PICKUP TRUCKS EQUIPPED WITH POWERS AND SONS STEERING LINKAGE. THE STEERING LINKAGE DRAG LINK INNER TIE ROD TO PITMAN ARM BALL STUD MAY FRACTURE. ALSO THE STEERING LINKAGE DAMPER ATTACHING THE BRACKET MAY YIELD AND SHIFT ON THE LINKAGE.

Consequence & remedy

Consequence: THIS COULD RESULT IN A LOSS OF STEERING CONTROL AND THE RESTRICTED ABILITY TO TURN THE VEHICLE IN ONE DIRECTION INCREASING THE RISK OF A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL REPLACE THE STEERING LINKAGE DRAG LINK INNER TIE ROD END ASSEMBLY, AND INSPECT THE STEERING LINKAGE DAMPER BRACKET FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON OR BEFORE FEBRUARY 16, 2009. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

08V641000 · Engine And Engine Cooling:engine:diesel

Dec 5, 2008

CHRYSLER IS RECALLING 108,429 MY 2007-2008 DODGE RAM 2500 AND 3500 PICKUP TRUCKS EQUIPPED WITH 6.7L DIESEL ENGINES. A SILENCER PAD CAN SAG AND CONTACT THE EXHAUST GAS RECIRCULATION (EGR) COOLER.

Consequence & remedy

Consequence: THIS COULD RESULT IN AN ENGINE COMPARTMENT FIRE.

Remedy: DEALERS WILL ADD A BRACKET TO SUPPORT THE ENGINE COMPARTMENT SILENCER PAD ADJACENT TO THE EGR COOLER. THE RECALL IS EXPECTED TO BEGIN DURING DECEMBER 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

3

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

AQ14003 · Chrysler's Execution Of 13V-528 & 529

Opened Oct 20, 2014 · Closed May 16, 2016

Status: closed (inferred from source dates) · Steering:linkages:tie Rod Assembly

RMD opened this audit query (AQ) investigation in order to better understand and evaluate Chrysler's process(es) for timely and efficient execution of its safety recall campaigns, including its oversight and management of its parts division Mopar.Prior to opening this investigation, RMD had raised concerns with the company related to its execution of two safety recalls, 13V-528 and 13V-529, both of which involved safety defects that could cause the involved vehicles, FCA?s heavier Dodge Ram trucks, to lose steering control suddenly and without warning.Specifically, RMD inquired about the availability of parts for recall repairs, by email and phone on January 15, 2014 and February 19, 2014, due to the volume of complaints it was receiving from owners alleging parts scarcity and parts restrictions. FCA steadfastly denied it had placed parts restrictions on its dealers to manage issues of parts scarcity.FCA shared material showing it had uncommitted stock of parts available for its dealers. Nevertheless, consumer complaints of lack of parts continued.RMD made independent inquiries tosome dealers tobetter understand the conflicting claims between owners alleging lack of ability to repair their defective vehicles due to lack of parts, and FCA?s information showing availability of parts.Dealers informed and provided documentation to RMD on February 21, 2014 and February 25, 2014 showing FCA had, in fact, put into place parts restrictions and, further, had in some instances canceled dealerships? back orders for parts.In addition, during the course of its dialogue with dealers, RMD discovered that FCA had notified their dealerships on February 27, 2014 to return the recall remedy parts over quality concerns, and had therefore effectively canceled its safety recall program without notification to NHTSA. RMD issued a request for information (IR) on October 21, 2014.The company failed to respond to a number of the questions RMD asked that required it to produce specifics surrounding the repairs and parts ordering process with the recalls, including a question about whether a dealer order for recall parts could be canceled and under what circumstances.

PE11009 · Outer Tie Rod Failure

Opened Apr 4, 2011 · Closed Feb 6, 2012

Status: closed (inferred from source dates) · Steering:linkages:tie Rod Assembly

ODI received complaints regarding failing tie rod ball studs on Model Year 2008-2011 Dodge Ram 2500 and 3500 vehicles resulting in loss of steering control.Chrysler concluded that misalignment of the left (driver side) ball stud on vehicles built with the Cross Car steering linkage system could allow contact between the bull stud and the ball housing which could weaken the stud and result in fracture.Chrysler submitted a recall notice on August 15, 2011 involving certain MY 2003-2011 Ram 2500 and Ram 3500 pickup trucks built or repaired with the Cross Car steering linkage.Chrysler will inspect, repair or realign the front end of the subject vehicles as needed.Chrysler's announcement of a safety recall on this matter addresses ODI's concerns.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10332525, 10357937, 10366591, 10303744, 10377166, 10373240, 10343969, 10375403, 10324831, 10373546, 10370771.