← New search

2008 Dodge RAM 2500

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2008 Dodge RAM 2500 do not stand out strongly from the model-year median of 275.

About this comparison →

When problems were reported

Mileage at the reported incident

227 reports with mileage · 90 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Steering. Review the 175 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Suspension. Review the 48 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Air Bags. Review the 30 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

12 crash reports8 fire reports7 injury reports

What owners actually said

317 reports
41,000 miles · Mar 6, 2010
SteeringCrash

INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). I OWN A 2008 DODGE RAM 2500 HEAVY DUTY PICKUP ON MARCH 1, 2010 AT 6:15 GOING DOWN W MAIN STREET A STRAIGHT ROAD MY VEHICLE LOST STEERING CONTROL AND STARTED TO VEER TO THE LEFT INTO THE OPPOSING LANE AND THEN TO GO OFF ROAD. I WAS DRIVIN…

Read full complaint

INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). I OWN A 2008 DODGE RAM 2500 HEAVY DUTY PICKUP ON MARCH 1, 2010 AT 6:15 GOING DOWN W MAIN STREET A STRAIGHT ROAD MY VEHICLE LOST STEERING CONTROL AND STARTED TO VEER TO THE LEFT INTO THE OPPOSING LANE AND THEN TO GO OFF ROAD. I WAS DRIVING AT APPRX 20-25 MILES PER HR . I HAVE LEARNED THERE IS A RECALL H46 THRU CHRYSLER BUT THEY ARE TELLING ME MY VEHICLES DIRTY AND WARRANTY RAN OUT AT 36,000 MILES I HAVE 46,000 MILES. I HAVE HAD MANY CONVERSATIONS WITH CHRYSLER AND THEY TELL ME TO GO THRU MY INSURANCE THE SAY I HIT CURB. THAT ONLY HAPPENED AFTER THE FACT THAT THE STEERING HAD NO CONTROL . I WAS TOLD BY THE DEALER PAUL SERVICE PERSON THAT IT HAS A RECALL FOR SOMETHING WITHIN A PART IN THE STEERING LINKAGE BUT IT WILL NOT BE COVERED AND CHRYSLER HAS A NEW OR REDESIGNED STEERING LINKAGE THAT CAN ONLY BE PURCHASED $1350.00. THE RECALL STATES DURING A PRIOR SERVICE APPT A MOPAR SERVICE PART STEERING LINKAGE MAY BEEN INSTALLED ON YOUR TRUCK [XXX] THE DRAG LINK INNER JOINT MAY FRACTURE UNDER CERTAIN DRIVING CONDITIONS THIS COULD RESULT IN A LOSS OF STEERING WHICH CAUSE A CRASH WITHOUT WARNING ALSO STEERING DAMPER BRACKET AT THE TIE ROD MAY LOOSEN ,THE LEGAL DEPARTMENT AT CHRYSLER IS WHERE MY CLAIM IS THERE # IS 1 248 944-7084 AND THEY ARE SENDING A INSPECTOR TO LOOK AT THIS [XXX]. PLEASE HELP ME I HAVE MISSED 2 DAYS OF WORK AND HAVE NO VEHICLE OR RENTAL AND MY TWIN DAUGHTERS THAT ARE 12 HAVE TO WALK HOME FROM BUS STOP ABOUT A HALF MILE ON A COUNTRY ROAD, NOT SAFE PLEASE HELP ME ! [XXX] *TR

NHTSA ODI #10317417

7,000 miles · Mar 4, 2010
Power Train

MY 2008, 2500 DODGE TRUCK 4X4 DIESEL HAS A BAD JERKING PROBLEM WHEN YOU LET OFF THE FUEL AND THEN PUT IT ON AGAIN. THE DEALERS HAVE CHANGED TURBO, WIRE HARNESSES, ALL SENSORS, EGR......... THIS HAS BEEN GOING ON SINCE 7000 MILES ON TRUCK. I HAVE NOW 47,000. EVERYONE INCLUDING THE DEALER HAS SAID ALL 2008'S DO THIS AND IT IS THE …

Read full complaint

MY 2008, 2500 DODGE TRUCK 4X4 DIESEL HAS A BAD JERKING PROBLEM WHEN YOU LET OFF THE FUEL AND THEN PUT IT ON AGAIN. THE DEALERS HAVE CHANGED TURBO, WIRE HARNESSES, ALL SENSORS, EGR......... THIS HAS BEEN GOING ON SINCE 7000 MILES ON TRUCK. I HAVE NOW 47,000. EVERYONE INCLUDING THE DEALER HAS SAID ALL 2008'S DO THIS AND IT IS THE FACTORY'S PROBLEM. *TR

NHTSA ODI #10316722

41,000 miles · Mar 2, 2010
Steering

TL*THE CONTACT OWNS A 2008 DODGE RAM 2500. WHILE DRIVING 45 MPH SHE NOTICED THAT THE VEHICLE WAS NOT DRIVING IN A STRAIGHT LINE, IT SWERVED TO THE LEFT WITHOUT HER TOUCHING THE STEERING WHEEL. SHE PARKED THE VEHICLE AND NOTICED THAT THE LEFT FRONT TIRE WAS TURNING AND THE RIGHT FRONT TIRE WAS NOT. THE VEHICLE WAS TOWED TO THE DE…

Read full complaint

TL*THE CONTACT OWNS A 2008 DODGE RAM 2500. WHILE DRIVING 45 MPH SHE NOTICED THAT THE VEHICLE WAS NOT DRIVING IN A STRAIGHT LINE, IT SWERVED TO THE LEFT WITHOUT HER TOUCHING THE STEERING WHEEL. SHE PARKED THE VEHICLE AND NOTICED THAT THE LEFT FRONT TIRE WAS TURNING AND THE RIGHT FRONT TIRE WAS NOT. THE VEHICLE WAS TOWED TO THE DEALER. THE DEALER STATED THE FRONT TIE ROD FAILED AND IT CAME OUT OF THE BALL JOINT. THE VEHICLE WILL BE REPAIRED. THE FAILURE AND THE CURRENT MILEAGES WERE 41,000.

NHTSA ODI #10315638

40,000 miles · Mar 1, 2010
Vehicle Speed Control

TL*THE CONTACT OWNS A 2008 DODGE RAM 2500. THE THROTTLE WAS STICKING INTERMITTENTLY PRIMARILY WHEN THE AIR CONDITIONER WAS ON. THE VEHICLE ALSO IDLED EXCESSIVELY WHEN SITTING STILL. HE HAS TAKEN THE VEHICLE TO SIX DEALERS AND THEY ALL SAID THAT THERE WAS NO FAILURE. THE MANUFACTURER ALSO SENT A REPRESENTATIVE TO LOOK AT THE VEH…

Read full complaint

TL*THE CONTACT OWNS A 2008 DODGE RAM 2500. THE THROTTLE WAS STICKING INTERMITTENTLY PRIMARILY WHEN THE AIR CONDITIONER WAS ON. THE VEHICLE ALSO IDLED EXCESSIVELY WHEN SITTING STILL. HE HAS TAKEN THE VEHICLE TO SIX DEALERS AND THEY ALL SAID THAT THERE WAS NO FAILURE. THE MANUFACTURER ALSO SENT A REPRESENTATIVE TO LOOK AT THE VEHICLE AND THEY COULD NOT DUPLICATE OR DIAGNOSE THE FAILURE. THE VIN WAS UNKNOWN. THE FAILURE MILEAGE WAS 40,000.

NHTSA ODI #10315243

15,000 miles · Jan 18, 2010
Seat Belts

PASSENGER SIDE SEAT BELT LOCKS AND CONTINUES TO TIGHTEN UNDER NORMAL DRIVING CONDITIONS. PASSENGER MUST RELEASE SEAT BELT AND RETURN TO "HOME" POSITION BEFORE APPLYING SEAT BELT. ANY TIME YOU HAVE TO REMOVE THE SEAT BELT WHILE MOVING, YOU ARE AT AN INCREASED RISK FOR INJURY/DEATH. I HAVE BEEN TO THE DEALERSHIP AND HAVE HAD THIS …

Read full complaint

PASSENGER SIDE SEAT BELT LOCKS AND CONTINUES TO TIGHTEN UNDER NORMAL DRIVING CONDITIONS. PASSENGER MUST RELEASE SEAT BELT AND RETURN TO "HOME" POSITION BEFORE APPLYING SEAT BELT. ANY TIME YOU HAVE TO REMOVE THE SEAT BELT WHILE MOVING, YOU ARE AT AN INCREASED RISK FOR INJURY/DEATH. I HAVE BEEN TO THE DEALERSHIP AND HAVE HAD THIS PART REPLACED TWICE. I HAVE A TOTAL OF 9 HOURS WAIT TIME TRYING TO REMEDY THIS PROBLEM AT THE DEALERSHIP. *TR

NHTSA ODI #10300171

40,000 miles · Jan 10, 2010
Steering

STEERING WANDERING STARTED DAYS BEFORE THEN THE DREADED DEATH WOBBLE. STARTED HAPPENING ST 70 MPH THEN 60 MPH NOW I CANT DRIVE OVER 55 MPH WITH OUT IT HAPPENING. *TR

NHTSA ODI #10298890

420 miles · Dec 17, 2009
Engine And Engine Cooling

EXHAUST LEAK INTO CAB OF TRUCK IS A DIESEL AND ACTUALLY MAKES YOU ILL WHEN RIDING IN IT. 4 ATTEMPTS BY DEALER HAVE FAILED TO RECTIFY PROBLEM. I PLACED A CO METER IN CAB AND IT WENT OFF THE SCALE WHICH GOES TO 99 PPM. *TR

NHTSA ODI #10296307

10,000 miles · Nov 22, 2009
Suspension

MY TRUCK SHAKES VIOLENTLY WHEN I HIT IMPERFECTIONS IN THE ROAD. IT HAPPENS 3 OR MORE TIMES A WEEK. I HAVE TO STOP MY TRUCK TO GET THE SHAKING TO CEASE. I HAVE HAD IT TO THE DEALER MORE THAN ONCE FOR THE PROBLEM. THEY COULD NOT "REPLICATE THE PROBLEM" THE FIRST TWO TIMES. THE THIRD TIME I DROVE AND THE SERVICE MAN RODE WITH…

Read full complaint

MY TRUCK SHAKES VIOLENTLY WHEN I HIT IMPERFECTIONS IN THE ROAD. IT HAPPENS 3 OR MORE TIMES A WEEK. I HAVE TO STOP MY TRUCK TO GET THE SHAKING TO CEASE. I HAVE HAD IT TO THE DEALER MORE THAN ONCE FOR THE PROBLEM. THEY COULD NOT "REPLICATE THE PROBLEM" THE FIRST TWO TIMES. THE THIRD TIME I DROVE AND THE SERVICE MAN RODE WITH ME. THEY DETERMINED IT WAS THE TIRES THAT WERE CAUSING THE PROBLEM. THEY SAID TIRES WERE NOT COVERED IN THE WARRANTY. SO IT LOOKS LIKE I GET TO FORK OVER A GRAND FOR NEW TIRES. *TR

NHTSA ODI #10293182

29,000 miles · Nov 5, 2009
Equipment

WENT TO TAKE OFF FROM A STOPLIGHT AND WHEN I ACCELERATED TO 1500 RPM THE EXHAUST BRAKE ENGAGED AND PREVENTED ME FROM INCREASING SPEED. I HAD TO LET OFF THE ACCELERATOR AND GENTLY ACCELERATE IN ORDER TO GET THE TRUCK MOVING. ONCE GOING, ANYTIME I TRIED TO INCREASE SPEED, THE EXHAUST BRAKE WOULD ENGAGE AND SLOW DOWN THE VEHICLE. I…

Read full complaint

WENT TO TAKE OFF FROM A STOPLIGHT AND WHEN I ACCELERATED TO 1500 RPM THE EXHAUST BRAKE ENGAGED AND PREVENTED ME FROM INCREASING SPEED. I HAD TO LET OFF THE ACCELERATOR AND GENTLY ACCELERATE IN ORDER TO GET THE TRUCK MOVING. ONCE GOING, ANYTIME I TRIED TO INCREASE SPEED, THE EXHAUST BRAKE WOULD ENGAGE AND SLOW DOWN THE VEHICLE. I HAD TO PULL OFF THE ROAD, SHUT OFF THE VEHICLE, AND THEN RESTART. THIS SEEMED TO TAKE CARE OF THE PROBLEM.. IT ONLY HAPPENED ONCE BUT IT WAS AT A BUSY INTERSECTION. *TR

NHTSA ODI #10291077

29,000 miles · Nov 5, 2009
Power Train

WHEN THE TRUCK IS STARTED AND PUT INTO GEAR, THE TRUCK WILL ROLL ABOUT 10 FEET AND THEN TAKE OFF. THE DRIVER HAS TO STAND ON THE BRAKES TO GET IT TO STOP. THE PROBLEM IS INTERMITTENT AND TENDS TO OCCUR AFTER IT SETS FOR MORE THAN 8 HOURS. IT ONLY HAPPENS DURING THE FIRST 3 -5 MINUTES AFTER STARTUP. IF DRIVER IS UNAWARE OF PROBLE…

Read full complaint

WHEN THE TRUCK IS STARTED AND PUT INTO GEAR, THE TRUCK WILL ROLL ABOUT 10 FEET AND THEN TAKE OFF. THE DRIVER HAS TO STAND ON THE BRAKES TO GET IT TO STOP. THE PROBLEM IS INTERMITTENT AND TENDS TO OCCUR AFTER IT SETS FOR MORE THAN 8 HOURS. IT ONLY HAPPENS DURING THE FIRST 3 -5 MINUTES AFTER STARTUP. IF DRIVER IS UNAWARE OF PROBLEM IT COULD EASILY LEAD TO DAMAGE TO OTHERS AS IT REQUIRES A GREAT DEAL OF FORCE TO GET THE TRUCK TO STOP.*TR

NHTSA ODI #10291073

Official recalls

7

16V352000 · Air Bags:frontal:passenger Side:inflator Module

May 24, 2016

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Consequence & remedy

Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

15V313000 · Air Bags:frontal:driver Side:inflator Module

May 26, 2015

Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.

13V528000 · Steering:linkages:tie Rod Assembly

Nov 6, 2013

Chrysler Group LLC (Chrysler) is recalling certain model year 2003-2008 Dodge RAM 2500 4x4 and 3500 4x4, model year 2007-2008 Dodge RAM 3500 4x2 Cab Chassis and model year 2006-2008 Dodge RAM 1500 Mega Cab 4x4 trucks manufactured February 12, 2002, through February 13, 2008. The left tie rod assembly may break.

Consequence & remedy

Consequence: A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.

Remedy: Chrysler notified owners and launched its recall campaign in January 2014. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N62.

13V529000 · Steering:linkages:tie Rod Assembly

Nov 6, 2013

Chrysler Group LLC (Chrysler) is recalling certain model year 2008-2012 RAM 2500 4X4 and 3500 4X4 trucks, 2008-2012 Dodge RAM 3500 4x2 Cab Chassis, and model year 2008 Dodge RAM 1500 Mega Cab 4x4. The left tie rod assembly may break.

Consequence & remedy

Consequence: A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.

Remedy: Chrysler notified owners on January 16, 2014 that dealers would inspect vehicles and replace the steering linkage assembly, if necessary. On or about February 27, 2014, Chrysler ceased its recall remedy program due to parts quality concerns, and then re-initiated it on or about April 14, 2014. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N49.

11V350000 · Steering:linkages:tie Rod Assembly

Jul 6, 2011

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2008-2011 DODGE RAM 2500/3500 4X4, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH MARCH 28, 2011; MODEL YEAR 2008-2011 DODGE RAM 3500 CAB CHASSIS 4X2, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH MARCH 28, 2011; AND MODEL YEAR 2008 DODGE RAM 1500 MEGA CAB 4X4, MANUFACTURED FROM FEBRUARY 14, 2008, THROUGH AUGUST 15, 2008, BECAUSE THE LEFT TIE ROD BALL STUD MAY FRACTURE. THIS CONDITION TENDS TO OCCUR DURING LOW SPEED PARKING LOT TYPE MANEUVERS WHEN THE CUSTOMER IS MAKING A TIGHT TURN. ADDITIONALLY, MODEL YEAR 2003-2008 DODGE RAM 2500/3500 VEHICLES MAY HAVE RECEIVED THE AFFECTED TIE ROD ASSEMBLY AS A REPLACEMENT PART DURING NORMAL SERVICE.

Consequence & remedy

Consequence: THIS CONDITION COULD RESULT IN THE POTENTIAL LOSS OF DIRECTIONAL STABILITY IN THE LEFT HAND FRONT WHEEL, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE TIE ROD ENDS FOR RELATIVE ORIENTATION AND REPLACE THE LEFT OUTER TIE ROD AS REQUIRED AND PERFORM A FRONT END TOE ALIGNMENT AS NEEDED. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 3, 2011. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

09V005000 · Steering:linkages:tie Rod Assembly

Jan 9, 2009

CHRYSLER IS RECALLING 32,782 MY 2008-2009 DODGE RAM 2500, 3500 AND 3500 CAB CHASSIS PICKUP TRUCKS EQUIPPED WITH POWERS AND SONS STEERING LINKAGE. THE STEERING LINKAGE DRAG LINK INNER TIE ROD TO PITMAN ARM BALL STUD MAY FRACTURE. ALSO THE STEERING LINKAGE DAMPER ATTACHING THE BRACKET MAY YIELD AND SHIFT ON THE LINKAGE.

Consequence & remedy

Consequence: THIS COULD RESULT IN A LOSS OF STEERING CONTROL AND THE RESTRICTED ABILITY TO TURN THE VEHICLE IN ONE DIRECTION INCREASING THE RISK OF A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL REPLACE THE STEERING LINKAGE DRAG LINK INNER TIE ROD END ASSEMBLY, AND INSPECT THE STEERING LINKAGE DAMPER BRACKET FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON OR BEFORE FEBRUARY 16, 2009. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

08V641000 · Engine And Engine Cooling:engine:diesel

Dec 5, 2008

CHRYSLER IS RECALLING 108,429 MY 2007-2008 DODGE RAM 2500 AND 3500 PICKUP TRUCKS EQUIPPED WITH 6.7L DIESEL ENGINES. A SILENCER PAD CAN SAG AND CONTACT THE EXHAUST GAS RECIRCULATION (EGR) COOLER.

Consequence & remedy

Consequence: THIS COULD RESULT IN AN ENGINE COMPARTMENT FIRE.

Remedy: DEALERS WILL ADD A BRACKET TO SUPPORT THE ENGINE COMPARTMENT SILENCER PAD ADJACENT TO THE EGR COOLER. THE RECALL IS EXPECTED TO BEGIN DURING DECEMBER 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

3

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

AQ14003 · Chrysler's Execution Of 13V-528 & 529

Opened Oct 20, 2014 · Closed May 16, 2016

Status: closed (inferred from source dates) · Steering:linkages:tie Rod Assembly

RMD opened this audit query (AQ) investigation in order to better understand and evaluate Chrysler's process(es) for timely and efficient execution of its safety recall campaigns, including its oversight and management of its parts division Mopar.Prior to opening this investigation, RMD had raised concerns with the company related to its execution of two safety recalls, 13V-528 and 13V-529, both of which involved safety defects that could cause the involved vehicles, FCA?s heavier Dodge Ram trucks, to lose steering control suddenly and without warning.Specifically, RMD inquired about the availability of parts for recall repairs, by email and phone on January 15, 2014 and February 19, 2014, due to the volume of complaints it was receiving from owners alleging parts scarcity and parts restrictions. FCA steadfastly denied it had placed parts restrictions on its dealers to manage issues of parts scarcity.FCA shared material showing it had uncommitted stock of parts available for its dealers. Nevertheless, consumer complaints of lack of parts continued.RMD made independent inquiries tosome dealers tobetter understand the conflicting claims between owners alleging lack of ability to repair their defective vehicles due to lack of parts, and FCA?s information showing availability of parts.Dealers informed and provided documentation to RMD on February 21, 2014 and February 25, 2014 showing FCA had, in fact, put into place parts restrictions and, further, had in some instances canceled dealerships? back orders for parts.In addition, during the course of its dialogue with dealers, RMD discovered that FCA had notified their dealerships on February 27, 2014 to return the recall remedy parts over quality concerns, and had therefore effectively canceled its safety recall program without notification to NHTSA. RMD issued a request for information (IR) on October 21, 2014.The company failed to respond to a number of the questions RMD asked that required it to produce specifics surrounding the repairs and parts ordering process with the recalls, including a question about whether a dealer order for recall parts could be canceled and under what circumstances.

PE11009 · Outer Tie Rod Failure

Opened Apr 4, 2011 · Closed Feb 6, 2012

Status: closed (inferred from source dates) · Steering:linkages:tie Rod Assembly

ODI received complaints regarding failing tie rod ball studs on Model Year 2008-2011 Dodge Ram 2500 and 3500 vehicles resulting in loss of steering control.Chrysler concluded that misalignment of the left (driver side) ball stud on vehicles built with the Cross Car steering linkage system could allow contact between the bull stud and the ball housing which could weaken the stud and result in fracture.Chrysler submitted a recall notice on August 15, 2011 involving certain MY 2003-2011 Ram 2500 and Ram 3500 pickup trucks built or repaired with the Cross Car steering linkage.Chrysler will inspect, repair or realign the front end of the subject vehicles as needed.Chrysler's announcement of a safety recall on this matter addresses ODI's concerns.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10332525, 10357937, 10366591, 10303744, 10377166, 10373240, 10343969, 10375403, 10324831, 10373546, 10370771.