← New search

2008 Dodge Magnum

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2008 Dodge Magnum do not stand out strongly from the model-year median of 100.5.

About this comparison →

How this year compares

Owner complaints by model year

Other model years Selected year
Compare all Magnum years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

All reported categories

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

58 reports with mileage · 35 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 67 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Air Bags. Review the 14 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 13 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

2 crash reports0 fire reports0 injury reports

Engine And Engine Cooling complaints

5 reports
Clear category filter
89,437 miles · Jan 26, 2015
Engine And Engine Cooling

TL*THE CONTACT OWNS 2008 DODGE MAGNUM. THE CONTACT STATED THAT WHILE DRIVING AT APPROXIMATELY 10 MPH, THE SERVICE ENGINE WARNING INDICATOR ILLUMINATED. THE FAILURE RECURRED ON MULTIPLE OCCASIONS. THE VEHICLE WAS TAKEN TO A DEALER. THE TECHNICIAN DIAGNOSED THAT THE CATALYTIC CONVERTER FAILED. THE VEHICLE WAS REPAIRED AND THE M…

Read full complaint

TL*THE CONTACT OWNS 2008 DODGE MAGNUM. THE CONTACT STATED THAT WHILE DRIVING AT APPROXIMATELY 10 MPH, THE SERVICE ENGINE WARNING INDICATOR ILLUMINATED. THE FAILURE RECURRED ON MULTIPLE OCCASIONS. THE VEHICLE WAS TAKEN TO A DEALER. THE TECHNICIAN DIAGNOSED THAT THE CATALYTIC CONVERTER FAILED. THE VEHICLE WAS REPAIRED AND THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE MILEAGE WAS 89,437.

NHTSA ODI #10678914

51,000 miles · Jun 9, 2010
Engine And Engine CoolingPower TrainSuspension

08 MAGNUM PURCHASED 08.08.2009 W/ 40,235 MILES W/ 48,000 EXTENDED WARRANTY. AROUND JANUARY OF 2010 STALLING IN PARKING LOTS, AT TRAFFIC LIGHTS, WHILE IN REVERSE. WHILE REGULAR DRIVING CAR WILL BUCK, AS THOUGH NEUTRAL WAS ENGAGED AND DISENGAGED. THIS MAY OCCUR WEEKLY, NO DIAGNOSIS WAS MADE ON MULTIPLE TRIPS. NOW WHILE DRIVING AT …

Read full complaint

08 MAGNUM PURCHASED 08.08.2009 W/ 40,235 MILES W/ 48,000 EXTENDED WARRANTY. AROUND JANUARY OF 2010 STALLING IN PARKING LOTS, AT TRAFFIC LIGHTS, WHILE IN REVERSE. WHILE REGULAR DRIVING CAR WILL BUCK, AS THOUGH NEUTRAL WAS ENGAGED AND DISENGAGED. THIS MAY OCCUR WEEKLY, NO DIAGNOSIS WAS MADE ON MULTIPLE TRIPS. NOW WHILE DRIVING AT 65-70MPH ON HIGHWAY ON 6/04/2010, RIGHT FRONT TIE ROD END "EXPLODES". I WAS ABLE TO WRESTLE CONTROL OF THE VEHICLE AND SAFELY PULL OVER TO SHOULDER AFTER NEARLY HITTING WALL. BOTH TIE ROD ENDS ARE CURRENTLY BEING REPLACED, AFTER MECHANIC DESCRIBES LEFT TIE ROD AS HAVING " EXCESSIVE PLAY". SPEED SENSOR DAMAGED BECAUSE RIGHT TIE ROD EXPLOSION. AS OFF NOW THE EXTENT OF THE DAMAGE IS STILL BEING ASSESSED, AND THE OLD PARTS HAVE BEEN REQUESTED TO STAY WITH THE CAR AS PROOF. THE ENGINE TROUBLES AND EXCESSIVE STALLING HAS NOT BEEN DIAGNOSED. PURCHASED DODGE BECAUSE OF LOVE FOR THE QUALITY AND CARS. AFTER INVESTIGATING; RECALLS/COMPLAINTS, NUMEROUS FORUMS I HAVE FOUND THIS PROBLEM TO BE IN THE HUNDREDS. PLEASE OPEN A CASE, I HAVE WAITED TO FILE A COMPLIANT SO THAT I WOULD HAVE TIME TO DO RESEARCH AND MAKE SURE I WOULD NOT BE "CRYING WOLF". CURRENTLY I AM TERRIFIED TO ACCEPT THE CAR, BECAUSE IF THE LEFT TIE ROD END WAS NOT IDENTIFIED AS PROBLEMATIC, THEN IT IS POSSIBLE THAT I COULD HAVE BEEN AWAITING REPAIRS FOR THE SAME PROBLEM LATER DOWN THE ROAD. AND I AM UNSURE IF I CAN KEEP WORRYING ABOUT WHEN AND WHERE THE CAR WILL STALL NEXT. IT IS NERVE RACKING TO HAVE TO CONSTANTLY PANIC WHEN IT DOES, OR EVEN IF IT WILL START BACK UP, ESPECIALLY WHEN THIS SHOULD NOT BE A ISSUE. THANK YOU. *TR

NHTSA ODI #10335478

479,900 miles · Jun 8, 2010
Engine And Engine Cooling

I PURCHASE THE DODGE MAGNUM IN DECEMBER OF 2008 IN FEBRUARY AND APRIL OF 2009 I HAD TO TAKE IT TO THE DEALER BECAUSE THE CAR WOULD NOT MOVE AFTER MAKING A STOP AT THE SIGNAL LIGHT ON TWO OCCASIONS WITHOUT SHUTTING THE CAR OFF AND RESTARTING IT. IN MAY ON 2010, I HAD TO TAKE MY CAR TO THE DEALER BECAUSE COOLANT LEAKING DUE TO WA…

Read full complaint

I PURCHASE THE DODGE MAGNUM IN DECEMBER OF 2008 IN FEBRUARY AND APRIL OF 2009 I HAD TO TAKE IT TO THE DEALER BECAUSE THE CAR WOULD NOT MOVE AFTER MAKING A STOP AT THE SIGNAL LIGHT ON TWO OCCASIONS WITHOUT SHUTTING THE CAR OFF AND RESTARTING IT. IN MAY ON 2010, I HAD TO TAKE MY CAR TO THE DEALER BECAUSE COOLANT LEAKING DUE TO WATER PUMP WENT OUT. *TR

NHTSA ODI #10335216

27,000 miles · Feb 17, 2010
Engine And Engine Cooling

WHILE DRIVING MY 2008 DODGE MAGNUM, MY CAR COMPLETELY SHUT OFF WITHOUT WARNING AND NOT ONE LIGHT INSIDE TURNED ON INDICATING A PROBLEM. THIS HAS HAPPENED ON THREE OCCASIONS WHEN I FIRST PURCHASED THE VEHICLE. THE CARS COMPUTER WAS REFLASHED TWICE AND I DON'T KNOW WHAT WAS DONE BESIDES THAT. IT OBVIOUSLY DIDN'T FIX THE PROBLEM CA…

Read full complaint

WHILE DRIVING MY 2008 DODGE MAGNUM, MY CAR COMPLETELY SHUT OFF WITHOUT WARNING AND NOT ONE LIGHT INSIDE TURNED ON INDICATING A PROBLEM. THIS HAS HAPPENED ON THREE OCCASIONS WHEN I FIRST PURCHASED THE VEHICLE. THE CARS COMPUTER WAS REFLASHED TWICE AND I DON'T KNOW WHAT WAS DONE BESIDES THAT. IT OBVIOUSLY DIDN'T FIX THE PROBLEM CAUSE MY CAR HAS SHUT OFF PLENTY OF TIMES AFTER THAT. THE LAST OCCASION WAS MONDAY 02-15-10 WHILE IN THE PARKING LOT, AS I PUT THE CAR IN REVERSE THE CAR STALLED WHEN I TOOK MY FOOT OFF THE BRAKE. IT JUST SHUT OFF AGAIN BUT THIS TIME AN ACTUAL LIGHT CAME ON. THE MALFUNCTION LIGHT CAME ON. *TR

NHTSA ODI #10311378

57,000 miles · Jun 17, 2009
Engine And Engine Cooling

TL*THE CONTACT OWNS A 2008 DODGE MAGNUM. THE CONTACT PURCHASED THE VEHICLE WITH 32,000 MILES. WHILE DRIVING AT AN UNKNOWN SPEED, THE ENGINE LOST POWER AND STALLED. THE INSTRUMENT PANEL GAUGES FLUCTUATED RIGHT BEFORE THE FAILURE OCCURRED. THE VEHICLE WAS TOWED TO THE DEALER AND THEY STATED THAT THE ENGINE LOCKED UP AND THE TO…

Read full complaint

TL*THE CONTACT OWNS A 2008 DODGE MAGNUM. THE CONTACT PURCHASED THE VEHICLE WITH 32,000 MILES. WHILE DRIVING AT AN UNKNOWN SPEED, THE ENGINE LOST POWER AND STALLED. THE INSTRUMENT PANEL GAUGES FLUCTUATED RIGHT BEFORE THE FAILURE OCCURRED. THE VEHICLE WAS TOWED TO THE DEALER AND THEY STATED THAT THE ENGINE LOCKED UP AND THE TOP PART OF THE ENGINE SEIZED. THE VEHICLE COULD NOT BE RESTARTED AFTER THE FAILURE OCCURRED. THE VEHICLE IS UNABLE TO BE DRIVEN. THERE WERE NO PREVIOUS FAILURES WITH THE VEHICLE. THE VIN WAS UNKNOWN. THE CURRENT AND FAILURE MILEAGES WERE 57,000.

NHTSA ODI #10274147

Official recalls

5

16V352000 · Air Bags:frontal:passenger Side:inflator Module

May 24, 2016

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Consequence & remedy

Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

15V313000 · Air Bags:frontal:driver Side:inflator Module

May 26, 2015

Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.

14V567000 · Electrical System:ignition

Sep 17, 2014

Chrysler Group LLC (Chrysler) is recalling certain model year 2008 Chrysler 300 vehicles manufactured May 31, 2007, to May 12, 2008, Dodge Magnum vehicles manufactured May 23, 2007, to May 12, 2008, Dodge Charger vehicles manufactured May 24, 2007, to May 12, 2008, Jeep Commander vehicles manufactured April 3, 2007, to May 12, 2008, and Jeep Grand Cherokee vehicles manufactured March 21, 2007, to May 12, 2008. In the affected vehicles, the ignition key (FOBIK) may not return to the "ON" position after being rotated to the "START" position, instead sticking between the two positions. Potentially, while the vehicle is being driven, the ignition may inadvertently move through the "RUN" position to the "ACCESSORY" or "OFF" ignition position, turning off the engine.

Consequence & remedy

Consequence: If the ignition stays between "START" and "ON" positions it could cause loss of certain electrical functions. If the ignition key inadvertently moves into the "OFF" or "ACCESSORY" position, the engine will turn off, which will then depower various key safety systems including but not limited to air bags, power steering, and power braking. Loss of functionality of these systems may increase the risk of crash and/or increase the risk of injury in the event of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the ignition switch and key FOBs, free of charge. The recall began August 19, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P57.

08V583000 · Power Train:automatic Transmission:lever And Linkage:column Shift

Nov 6, 2008

CHRYSLER IS RECALLING 20,283 MY 2006-2009 CHARGER AND MAGNUM VEHICLES BUILT WITH THE POLICE PACKAGE AND EQUIPPED WITH A COLUMN SHIFTER. THE GEARSHIFT CABLE MAY BECOME DISENGAGED FROM THE STEERING COLUMN MOUNTING BRACKET AND CAUSE AN INCORRECT TRANSMISSION GEARSHIFT POSITION DISPLAY.

Consequence & remedy

Consequence: THIS COULD ALLOW THE VEHICLE TO MOVE IN AN UNEXPECTED DIRECTION STARTLING THE DRIVER, AND CAUSE A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL ADD A REDUNDANT LOCKING MECHANISM TO THE GEARSHIFT CABLE AT THE MOUNTING BRACKET TO ENSURE PROPER RETENTION AND SHIFT LINKAGE FUNCTION. THE RECALL BEGAN ON NOVEMBER 10, 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

08V295000 · Power Train:axle Hubs

Jul 2, 2008

CHRYSLER IS RECALLING 5,509 MY 2008 300, DODGE MAGNUM, AND CHARGER VEHICLES. THE TORQUE RETENTION CRIMP FEATURE WAS MISSED DURING THE MANUFACTURE OF ONE LOT OF REAR AXLE HUB NUTS. THIS COULD CAUSE THE NUTS TO LOOSEN AND ALLOW THE HALFSHAFT TO DISENGAGE FROM THE WHEEL HUB.

Consequence & remedy

Consequence: THIS COULD CAUSE THE VEHICLE TO LOSE POWER AND RESULT IN A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL REPLACE THE REAR AXLE HUB NUTS. THE RECALL BEGAN ON JULY 21, 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

PE08052 · Prndl Misalignment

Opened Sep 2, 2008 · Closed Nov 10, 2008

Status: closed (inferred from source dates) · Power Train:automatic Transmission:lever And Linkage:column Shift

IN A NOVEMBER 5, 2008 LETTER, CHRYSLER SUBMITTED A DEFECT INFORMATION REPORT DESCRIBING A DEFECT CONDITION THAT COULD RESULT IN PRNDL MISALIGNMENT (I.E., INCORRECT GEAR INDICATION) IN APPROXIMATELY 20,300 MODEL YEAR (MY) 2006 THROUGH 2009 DODGE CHARGER AND MAGNUM POLICE VEHICLES BUILT FROM MAY 17, 2005 THROUGH OCTOBER 21, 2008 (NHTSA RECALL NO. 08V-583, CHRYSLER RECALL H37).ACCORDING TO CHRYSLER, THE GEARSHIFT CABLE MAY BECOME DISENGAGED FROM THE STEERING COLUMN MOUNTING BRACKET AND CAUSE AN INCORRECT TRANSMISSION GEARSHIFT POSITION DISPLAY.THIS COULD ALLOW THE VEHICLE TO MOVE INADVERTENTLY AND CAUSE A CRASH WITHOUT WARNING.CHRYSLER DEALERS WILL REMEDY THE DEFECT CONDITION BY INSTALLING A REDUNDANT LOCKING MECHANISM TO THE GEARSHIFT CABLE AND THE MOUNTING BRACKET TO ENSURE PROPER RETENTION AND SHIFT LINKAGE FUNCTION. CHRYSLER USES A UNIQUE COLUMN SHIFTER IN THESE POLICE VEHICLES.AFTER PE08-052 WAS OPENED, CHRYSLER INSPECTED A MY 2009 POLICE VEHICLE AND NOTED THAT THOUGH THE GEARSHIFT CABLE APPEARED FULLY SEATED INTO THE STEERING COLUMN MOUNTING BRACKET, THE CABLE RETENTION FEATURE (LOCKING PIN) WAS NOT FULLY SEATED.CHRYSLER SUBSEQUENTLY DETERMINED THAT IF THE RETENTION FEATURE IS NOT FULLY SEATED, THE CABLE MAY DISENGAGE FROM THE MOUNTING BRACKET, RESULTING IN THE SHIFT LINKAGE SYSTEM NOT FUNCTIONING TO DESIGN INTENT WITH THE POTENTIAL FOR INCORRECT GEAR POSITION INDICATION VIA THE PRNDL DISPLAY.CHYSLER'S INSPECTION OF 59 MY 2009 DODGE CHARGER AND MAGNUM POLICE VEHICLES IN SEPTEMBER AND OCTOBER FOUND 30 WHERE THE GEARSHIFT CABLE WAS NOT FULLY ENGAGED TO THE MOUNTING BRACKET.THERE ARE NO REPORTED CRASHES OR INJURIES RELATED TO THE DEFECT CONDITION TO DATE. THIS INVESTIGATION IS CLOSED.