IllustrationWhile coming around a 35mph turn my car shut its self off. Normally it would say please put car in park but it shut off and had to panic and pull hard to make it around the turn. Put car in park then I was able to restart the car.
2017 Dodge Charger
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all Charger years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
170–25K
2325–50K
1250–75K
475–100K
4100–150K
1150K+
61 reports with mileage · 67 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 48 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 20 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 18 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
3 crash reports3 fire reports2 injury reports
Fuel/propulsion System complaints
6 reportsELECTRONIC THROTTLE CONTROL APPEARS TO BE SENDING ERROR CODES TO A HUM. THE CAR IS NOT GETTING ENOUGH FUEL TO ACCELERATE ON THE HIGHWAY.
EVAP HAS SYSTEM HAS A SMALL LEAK. MY GAS IS LEAKING FROM THE OPPOSITE SIDE OF THE GAS TANK .THE CHECK ENGINE LIGHT JUST CAME ON. THE GAS LEAKED 2 WEEKS AGO AND NOW THE CHECK ENGINE LIGHT IS ON AND I KEEP SMELLING GAS .THE CAR WAS STATIONARY.*DT*JB
MY VEHICLE HAD PROBLEMS JUST AFTER THE 1 YEAR MARK. IN OCTOBER 2018 FILLED THE GAS TANK AND BEGAN TO PULL AWAY FROM THE PUMP, AT THIS TIME THE CAR WAS IN "DRIVE" BUT DOWN-SHIFTED INTO WHAT FELT LIKE NEUTRAL. AN ERROR CODE RAN ACROSS THE DASH SAYING "PUSH P TO PARK, SELECT DESIRED GEAR". I PUT IT IN PARK AND TURNED IT OFF THEN O…
Read full complaint
MY VEHICLE HAD PROBLEMS JUST AFTER THE 1 YEAR MARK. IN OCTOBER 2018 FILLED THE GAS TANK AND BEGAN TO PULL AWAY FROM THE PUMP, AT THIS TIME THE CAR WAS IN "DRIVE" BUT DOWN-SHIFTED INTO WHAT FELT LIKE NEUTRAL. AN ERROR CODE RAN ACROSS THE DASH SAYING "PUSH P TO PARK, SELECT DESIRED GEAR". I PUT IT IN PARK AND TURNED IT OFF THEN ON AGAIN. THIS HAPPENED TWICE BUT IT STILL DID IT. I PARKED THE CAR, TURNED IT OFF AND HAD IT TOWED- DEALER SAID IT WAS FINE, AND WASN'T THROWING ANY CODES AND LET ME DRIVE AWAY. NOT 5 MILES DOWN THE ROAD AND IT STARTED SMELLING OF GAS AND WAS RIDING VERY ROUGH AND BACKFIRING. I PULL OVER TO THE NEAREST NEXT DEALERSHIP AND THEY NOTICE THAT GAS IS POURING OUT THE BACK OF THE CAR. DIAGNOSED AS AN 'OVERFILLED CHARCOAL CANISTER' STATING THAT I OVERFILLED THE GAS TANK. WAS REPAIRED, I HAD TO SUBMIT TO HAVE IT COVERED UNDER WARRANTY. I GET THE VEHICLE BACK AND NOT 2 MONTHS LATER THE EXACT SAME ISSUE AFTER FILLING TANK WITH GAS. GAS IS POURING OUT THE BACK, GAS GAUGE IS GOING CRAZY RISING AND FALLING AND FINALLY DROPPING OFF AS GAS POURS OUT THE BACK. HAD IT TOWED AGAIN AND REPAIRED AT A 3RD DEALERSHIP. GIVEN BACK TO ME AND TOLD IT WAS COVERED UNDER WARRANTY BUT THAT WE OVERFILLED THE TANK. HAPPENED A THIRD TIME NOT 3 MONTHS LATER AND FINALLY THE ENTIRE GAS TANK WAS REPLACED. BROUGHT IT HOME AND WAS TOLD I SHOULD BE ABLE TO FILL IT, AS THE FIRST TWO TIMES IT WAS LIKELY A SENSOR IN THE GAS TANK CAUSING THE ISSUES. THE CAR SMELLED OF GAS AGAIN WHEN I STOPPED TO FILL THE TANK ON THE WAY BACK FROM THE DEALERSHIP. MY HUSBAND PULLED THE SEATS BACK AND HAD TO SOAK UP THE OVERFLOW FROM THE CANISTER HIMSELF- I DON'T FILL THE TANK ALL THE WAY ANYMORE FOR FEAR OF A FIRE. MY DAUGHTER COMPLAINS OF HEADACHES WHEN IN THE CAR- WONDERING IF ITS RELATED TO THE POOLING GAS UNDER HER CARSEAT. VERY CONCERNED THAT THIS IS NOT BEING TAKEN SERIOUSLY BY DODGE.
RECENTLY I'VE BEEN HAVING SOME ISSUES WITH MY VEHICLE WITH IT TURNING ON AND OFF WHEN I FIRST GO TO START IT UP. NOW I AM HAVING A BIGGER ISSUE BECAUSE THE CAR DECIDED TO TURN OFF ON ME MULTIPLE TIMES WHILE DRIVING. LUCKILY I AM FULLY AWARE OF WHAT IS HAPPENING TO ME WHILE DRIVING. I'VE TAKEN IT TO DODGE AND THEY SEEM TO NOT CAR…
Read full complaint
RECENTLY I'VE BEEN HAVING SOME ISSUES WITH MY VEHICLE WITH IT TURNING ON AND OFF WHEN I FIRST GO TO START IT UP. NOW I AM HAVING A BIGGER ISSUE BECAUSE THE CAR DECIDED TO TURN OFF ON ME MULTIPLE TIMES WHILE DRIVING. LUCKILY I AM FULLY AWARE OF WHAT IS HAPPENING TO ME WHILE DRIVING. I'VE TAKEN IT TO DODGE AND THEY SEEM TO NOT CAR OR EVEN TRY TO FIGURE OUT WHAT IS WRONG BECAUSE I CAN NOT REENACT THE PROBLEM, EVEN THOUGH I HAVE VIDEO OF IT NOT STARTING UP IN THE BEGINNING. SIMPLY BECAUSE THERE ARE NO CODES THAT COME UP, WHICH OF COURSE MAKES IT EASIER ON THEM TO JUST PUSH THE CUSTOMER AWAY. NOW IN MY OPINION I FEEL LIKE THIS CAN BE A LIFE AND DEATH SITUATION IF SOMEONE LIKE MY MOTHER OR MY GRANDMA OWN THE VEHICLE BECAUSE THEY WOULD NOW KNOW HOW TO CONTROL SUCH A HEAVY VEHICLE. I BELIEVE DODGE SHOULD LOOK DEEPER INTO THIS PROBLEM CONSIDERING THE FACT THAT THERE ARE A LOT OF FORUMS ONLINE SUGGESTING A PROBLEM.
SHORTLY AFTER I PURCHASED A NEW VEHICLE I NOTICED A STRONG FUEL SMELL OUTSIDE AND INSIDE MY CAR AND WHEN THE AIR WAS ON THE SMELL WAS COMING THROUGH THE AIR VENTS. I BROUGHT IT IN THE DEALERSHIP AND THEY SMELLED THE GAS OUTSIDE THE CAR. THEY PULLED UP MY BACKSEATS AND THERE WAS A PUDDLE OF GAS THAT LEAKED FROM THE FUEL PUMP. …
Read full complaint
SHORTLY AFTER I PURCHASED A NEW VEHICLE I NOTICED A STRONG FUEL SMELL OUTSIDE AND INSIDE MY CAR AND WHEN THE AIR WAS ON THE SMELL WAS COMING THROUGH THE AIR VENTS. I BROUGHT IT IN THE DEALERSHIP AND THEY SMELLED THE GAS OUTSIDE THE CAR. THEY PULLED UP MY BACKSEATS AND THERE WAS A PUDDLE OF GAS THAT LEAKED FROM THE FUEL PUMP. THEY REPLACED THE FUEL PUMP AND A FEW DAYS AFTER GETTING MY CAR BACK WHEN I FILLED UP MY TANK AGAIN THE SAME THING HAPPENED AND THIS TIME IT WAS LEAKING GAS FROM THE BOTTOM OF MY CAR. AFTER THAT 2ND REPAIR I GOT MY CAR BACK AGAIN A FEW DAYS LATER AFTER I FILLED UP MY TANK AND THE SAME THING HAPPENED. THE 3RD TIME THEY ENDED UP REPLACING THE GAS TANK. THE CAR STILL HAS A STRONG GAS SMELL THAT CAUSES ME TO HAVE HEADACHES, DIZZINESS, AND NAUSEA. I DO NOT FEEL SAFE IN MY CAR BECAUSE LATELY SINCE I'VE BEEN HAVING THESE PROBLEMS WITH THE CAR LEAKING GAS I'VE BEEN GETTING ALOT OF STATIC SHOCK WHEN I TOUCH MY CAR.
Official recalls
418V332000 · Electrical System:software; Electrical System:wiring; Vehicle Speed Control:cruise Control
May 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence & remedy
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Additional source detail variants (3)
Electrical System:software
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Vehicle Speed Control:cruise Control
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Electrical System:wiring
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
18V281000 · Power Train:driveline:driveshaft
May 1, 2018
Chrysler (FCA US LLC) is recalling certain 2015-2018 Dodge Charger pursuit police vehicles equipped with all-wheel drive and V8 engines. The front driveshaft universal joint may seize or fracture causing the shaft to detach from the vehicle.
Consequence & remedy
Consequence: If the front driveshaft detaches from the vehicle it may become a road hazard, increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the front driveshaft, free of charge. The recall began June 27, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U37.
17V496000 · Engine And Engine Cooling:engine
Aug 8, 2017
Chrysler (FCA US LLC) is recalling certain 2017 Dodge Challenger and Charger vehicles equipped with Hellcat engines. The engine oil cooler (EOC) hoses may fail resulting in a rapid loss of engine oil.
Consequence & remedy
Consequence: If an EOC line fails, oil may spray onto the windshield or contact a hot surface, impairing driver visibility and increasing the risk of a crash or fire.
Remedy: Chrysler will notify owners, and dealers will replace the EOC lines, free of charge. The recall began October 3, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T48.
17V097000 · Power Train:axle Assembly:axle Shaft
Feb 14, 2017
Chrysler (FCA US LLC) is recalling certain 2014-2017 Dodge Charger and Chrysler 300 vehicles equipped with all-wheel drive (AWD). The front driveshaft bolts may loosen and allow the front driveshaft to disconnect, potentially causing a loss of motive power.
Consequence & remedy
Consequence: A loss of motive power can increase the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace all eight front driveshaft bolts, free of charge. The recall began April 7, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T03.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.