NHTSA owner reports · September 18, 2026 snapshot.
Service Brakes complaints
31 reportsClear category filterMileage unknown · Jan 31, 2017
Electrical SystemElectronic Stability Control (esc)Service Brakes
I ALWAYS BRING MY CAR TO RANCHO CHRYSLER JEEP DODGE ON 8010 BALBOA AVENUE SAN DIEGO, CA 92111 REGARDING THE "BATTER SAVER MODE". I'VE HAD THIS CAR FOR ALMOST 2 YEARS AND HAVE GONE IN SEVERAL TIMES ABOUT THIS ISSUE. THEY REPLACED THE BATTERY/ALTERNATOR AT LEAST THAT'S WHAT I WAS TOLD AND THE "BATTERY SAVER MODE" STILL COMES ON. T…
Read full complaint
I ALWAYS BRING MY CAR TO RANCHO CHRYSLER JEEP DODGE ON 8010 BALBOA AVENUE SAN DIEGO, CA 92111 REGARDING THE "BATTER SAVER MODE". I'VE HAD THIS CAR FOR ALMOST 2 YEARS AND HAVE GONE IN SEVERAL TIMES ABOUT THIS ISSUE. THEY REPLACED THE BATTERY/ALTERNATOR AT LEAST THAT'S WHAT I WAS TOLD AND THE "BATTERY SAVER MODE" STILL COMES ON. THE ISSUE IS IF YOU TURN OFF THE CAR IT GOES AWAY. I WAS INFORMED TO BRING IT BACK IN IF THE "BATTERY SAVER MODE" COMES BACK ON BUT IF THE PLACE ISN'T OPENED THAT'S IMPOSSIBLE TO DO SO. I WOULD LIKE THIS TO BE FIXED, MY CAR CUTS OFF AT TIMES WHEN I START IT AND DRIVE OFF IN THE MORNING WHEN IT'S COLDER AND THIS HAS BEEN HAPPENING FOR YEARS WHICH THIS WAS REPORTED TO THE CAR COMPANY AS WELL.
NHTSA ODI #10948744
Mileage unknown · Dec 1, 2016
Service BrakesCrash
TL* THE CONTACT OWNS A 2014 DODGE CHARGER. WHILE APPROACHING A RED LIGHT AND DEPRESSING THE BRAKE PEDAL, THE BRAKES FAILED TO ENGAGE AND THE CONTACT'S VEHICLE ROLLED INTO THE REAR OF ANOTHER VEHICLE. A POLICE REPORT WAS FILED AND NO INJURIES WERE SUSTAINED. THE FAILURE OCCURRED ON SEVERAL OCCASIONS. THERE WERE NO WARNING INDICAT…
Read full complaint
TL* THE CONTACT OWNS A 2014 DODGE CHARGER. WHILE APPROACHING A RED LIGHT AND DEPRESSING THE BRAKE PEDAL, THE BRAKES FAILED TO ENGAGE AND THE CONTACT'S VEHICLE ROLLED INTO THE REAR OF ANOTHER VEHICLE. A POLICE REPORT WAS FILED AND NO INJURIES WERE SUSTAINED. THE FAILURE OCCURRED ON SEVERAL OCCASIONS. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS UNKNOWN.
NHTSA ODI #10929467
41,000 miles · Sep 6, 2016
Electronic Stability Control (esc)Service Brakes
WHEN DRIVING, I PRESSED BRAKE PEDAL TO STOP THE CAR AND HEARD A SCREECH NOISE, CAR TREMBLED A BIT AND CAME TO A STOP. WHEN I CONTINUED TO DRIVE WITHIN A COUPLE OF MINUTES THE ABS LIGHT CAME ON AND THE ELECTRICAL STABILITY LIGHT CAME ON. IT TURNED OFF FOR A COUPLE OF HOURS LATER, BUT IT TURNED ON AGAIN THE NEXT DAY IN THE MORNIN…
Read full complaint
WHEN DRIVING, I PRESSED BRAKE PEDAL TO STOP THE CAR AND HEARD A SCREECH NOISE, CAR TREMBLED A BIT AND CAME TO A STOP. WHEN I CONTINUED TO DRIVE WITHIN A COUPLE OF MINUTES THE ABS LIGHT CAME ON AND THE ELECTRICAL STABILITY LIGHT CAME ON. IT TURNED OFF FOR A COUPLE OF HOURS LATER, BUT IT TURNED ON AGAIN THE NEXT DAY IN THE MORNING WHEN I STARTED THE VEHICLE AND HAS STAYED ON SINCE.
NHTSA ODI #10903748
38,000 miles · Jul 21, 2016
Service BrakesSteering
WHILE DRIVING AND PREPARING TO TURN MY VEHICLE TOOK CONTROL AND I WAS NO LONGER ABLE TO BREAK OR TURN. THANKFULLY THERE WAS NOBODY IN THE NEIGHBOR AT THE TIME AND WITH LESS THAN A FOOT FROM HITTING THE STOP SIGN I WAS ABLE TO STOP. I TOOK IT TO THE DEALER WHERE I PURCHASED (1.5 YEARS PRIOR)AND THEY SAID NOTHING WAS WRONG JUST N…
Read full complaint
WHILE DRIVING AND PREPARING TO TURN MY VEHICLE TOOK CONTROL AND I WAS NO LONGER ABLE TO BREAK OR TURN. THANKFULLY THERE WAS NOBODY IN THE NEIGHBOR AT THE TIME AND WITH LESS THAN A FOOT FROM HITTING THE STOP SIGN I WAS ABLE TO STOP. I TOOK IT TO THE DEALER WHERE I PURCHASED (1.5 YEARS PRIOR)AND THEY SAID NOTHING WAS WRONG JUST NEEDED A NEW BATTERY. I INSISTED THIS WAS NOT THE ISSUE SO THE MANAGER HAD HIS ASSOCIATE TEST DRIVE TO COME TO THE SAME CONCLUSION THE STEERING AND BRAKE SYSTEM IS FINE. NOT HAPPY I LEFT AFTER PURCHASING THE BATTERY AND HERE WE ARE 1.5 WEEKS LATER WITH THE SAME ISSUE. I TRIED TO DRIVE OUT OF WORK YESTERDAY AND I LOST CONTROL TO MY STEERING AND IT LOCKED. I PUT MY CAR IN PARK AND TRIED ONCE MORE THE SAME THING HAPPENED, I THEN TRY TO RESTART BUT IT WOULD NOT ALLOW ME TO DO SO. I HAD TO DISCONNECT THE BATTERY AND IT STARTED. NOT FEELING SAFE FOR MY LIFE I LEFT THE CAR AT WORK AND STILL DO NOT WANT TO DRIVE IT. FROM WHAT I AM READING I AM NOT THE ONLY 2014 DODGE CHARGER HAVING THIS ISSUE. I NEED THIS FIXED IF I WAS ON THE FREEWAY WHO KNOWS WHAT WOULD HAVE HAPPENED.
NHTSA ODI #10887467
6,169 miles · Jun 14, 2016
Electronic Stability Control (esc)Service Brakes
LOSS OF ANTI-LOCK BRAKES AND LOSS OF TRACTION CONTROL WHILE DRIVING. WARNING LIGHTS INDICATED FOR BOTH. CAUSE WAS A BAD WHEEL SENSOR DRIVER SIDE REAR. 6,169 MILES.
NHTSA ODI #10874244
15,000 miles · Jan 27, 2016
EngineService Brakes
TL* THE CONTACT OWNS A 2014 DODGE CHARGER. WHILE DRIVING APPROXIMATELY 65 MPH, THE VEHICLE STALLED WITHOUT WARNING. AFTER RESTARTING, THE VEHICLE RESUMED NORMAL OPERATION. THE FAILURE RECURRED ON THREE SEPARATE OCCASSIONS. IN ADDITION, THE ABS AND ANTI-SKID WARNING INDICATORS ILLUMINATED DURING BRAKING AS THE BRAKE PEDAL TRAVELE…
Read full complaint
TL* THE CONTACT OWNS A 2014 DODGE CHARGER. WHILE DRIVING APPROXIMATELY 65 MPH, THE VEHICLE STALLED WITHOUT WARNING. AFTER RESTARTING, THE VEHICLE RESUMED NORMAL OPERATION. THE FAILURE RECURRED ON THREE SEPARATE OCCASSIONS. IN ADDITION, THE ABS AND ANTI-SKID WARNING INDICATORS ILLUMINATED DURING BRAKING AS THE BRAKE PEDAL TRAVELED TO THE FLOORBOARD. THE BRAKE FUNCTIONED PROPERLY WITHIN SECONDS. THE FAILURE RECURRED SPORADICALLY. THE VEHICLE WAS TAKEN TO THE DEALER FOR DIAGNOSTIC TESTING; HOWEVER, A FAILURE CODE WAS NOT DETECTED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 15,000.
NHTSA ODI #10822679
39,000 miles · Oct 29, 2015
Electronic Stability Control (esc)Service BrakesVehicle Speed Control
WHILE DRIVING ON A TOWN ROAD AT ABOUT 35 MPH, THE WARNING LIGHTS FOR THE ABS AND ESC SYSTEMS LIT. I SUBSEQUENTLY DETERMINED THAT THE VEHICLE CRUISE CONTROL ALSO NO LONGER FUNCTIONED. I CONTACTED CHRYSLER SINCE THE VEHICLE RECENTLY HAD A RECALL PERFORMED FOR ALTERNATOR REPLACEMENT, AND SYMPTOMS INCLUDED IN THAT RECALL - CHRYSLER …
Read full complaint
WHILE DRIVING ON A TOWN ROAD AT ABOUT 35 MPH, THE WARNING LIGHTS FOR THE ABS AND ESC SYSTEMS LIT. I SUBSEQUENTLY DETERMINED THAT THE VEHICLE CRUISE CONTROL ALSO NO LONGER FUNCTIONED. I CONTACTED CHRYSLER SINCE THE VEHICLE RECENTLY HAD A RECALL PERFORMED FOR ALTERNATOR REPLACEMENT, AND SYMPTOMS INCLUDED IN THAT RECALL - CHRYSLER P60 / NHTSA 14V-634 - INDICATE THAT MODES OF FAILURE MAY INCLUDE DISABLING ABS AND ESC. CHRYSLER STATED THAT "SOMETIMES THEY MAY NEED TO DO THE RECALL AGAIN". BROUGHT VEHICLE TO DEALER. DIAGNOSED AS A SENSOR FAILURE. I HAD TO PAY FOR REPAIRS.SERVICE WRITER STATED THAT THIS FAILURE HAPPENS ON THESE CARS QUITE FREQUENTLY, AND EVEN "GUESSED" CORRECTLY WHAT NEEDED TO BE REPLACED BEFORE THE TECH WORKED ON IT. ESC AND ABS ARE BOTH SIGNIFICANT SAFETY SYSTEMS.
NHTSA ODI #10786967
26,000 miles · Oct 1, 2015
Electrical SystemPower TrainService BrakesCrashInjury
TL* THE CONTACT OWNS A 2014 DODGE CHARGER. WHILE DRIVING APPROXIMATELY 35 MPH, THE VEHICLE SUDDENLY SHUT OFF AND THE DRIVER WAS UNABLE TO STEER OR STOP THE VEHICLE BEFORE CRASHING INTO A TRACTOR TRAILER AND A GUARDRAIL. THE DRIVER SUSTAINED AN INJURED BACK DURING THE INCIDENT, BUT DID NOT REQUIRE MEDICAL ATTENTION. A POLICE REPO…
Read full complaint
TL* THE CONTACT OWNS A 2014 DODGE CHARGER. WHILE DRIVING APPROXIMATELY 35 MPH, THE VEHICLE SUDDENLY SHUT OFF AND THE DRIVER WAS UNABLE TO STEER OR STOP THE VEHICLE BEFORE CRASHING INTO A TRACTOR TRAILER AND A GUARDRAIL. THE DRIVER SUSTAINED AN INJURED BACK DURING THE INCIDENT, BUT DID NOT REQUIRE MEDICAL ATTENTION. A POLICE REPORT WAS NOT FILED. PRIOR TO THE INCIDENT, THE FAILURE OCCURRED ON MULTIPLE OCCASIONS AND THE VEHICLE WAS SERVICED BY THE DEALER WHO REPLACED THE ABS SENSOR, ABS MODULE, TRANSMISSION MODULE, AND THE MAIN COMPUTER, BUT THE FAILURE CONTINUED TO OCCUR. THE MANUFACTURER WAS NOTIFIED OF THE FAILURES. THE VIN WAS INVALID. THE FAILURE MILEAGE WAS 26,000.
NHTSA ODI #10778938
32,616 miles · Sep 24, 2015
Service BrakesSuspension
TL* THE CONTACT OWNS A 2014 DODGE CHARGER. WHILE DRIVING AT AN UNKNOWN SPEED, THE VEHICLE MADE AN ABNORMALLY LOUD SOUND. WHEN THE BRAKE PEDAL WAS ACTIVATED, THE REAR END OF THE VEHICLE VIBRATED. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIFIED. THE APPROXIMATE FAILURE MIL…
Read full complaint
TL* THE CONTACT OWNS A 2014 DODGE CHARGER. WHILE DRIVING AT AN UNKNOWN SPEED, THE VEHICLE MADE AN ABNORMALLY LOUD SOUND. WHEN THE BRAKE PEDAL WAS ACTIVATED, THE REAR END OF THE VEHICLE VIBRATED. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIFIED. THE APPROXIMATE FAILURE MILEAGE WAS 32,616.
NHTSA ODI #10776472
10,552 miles · Aug 4, 2015
Electronic Stability Control (esc)Service BrakesVehicle Speed Control
TWO OF THE LIGHTS ON THE INSTRUMENT CLUSTER WARNING WERE ON:ESC(ELECTRONIC STABILITY CONTROL) AND ABS.I TOOK MY CAR FOR SERVICE AT THE DEALER AND I WAS TOLD TO LEAVE IT FOR REPAIRS. AFTER FOUR DAYS I RECEIVED A PHONE CALL WHICH I GOT INFORMED THAT THE REPLACEMENT PART WAS OUT OF STOCK AND IT NEED TO BE ORDER AND THEY TOLD ME TH…
Read full complaint
TWO OF THE LIGHTS ON THE INSTRUMENT CLUSTER WARNING WERE ON:ESC(ELECTRONIC STABILITY CONTROL) AND ABS.I TOOK MY CAR FOR SERVICE AT THE DEALER AND I WAS TOLD TO LEAVE IT FOR REPAIRS. AFTER FOUR DAYS I RECEIVED A PHONE CALL WHICH I GOT INFORMED THAT THE REPLACEMENT PART WAS OUT OF STOCK AND IT NEED TO BE ORDER AND THEY TOLD ME THAT EVEN THOUGH THE CAR NEEDED REPAIRS IT WAS SAFE TO DRIVE IT UNTIL THE PART ARRIVES.AFTER TWO WEEKS, I VISITED AGAIN THE DEALER AND THE PART WAS NOT THERE AND NOW AND I HAVE TO WAIT AND I ALSO NEEDED TO BE PLACE IN A WAITING LIST IN WHICH I WOULD HAVE NUMBER 254 (THOSE ARE THE AMOUNT OF CARS WHICH NEEDS TO REPLACED THE SAME PART). IN MY LAST VISITED TO THE DEALER I INFORMED THAT THE CAR IS WORSE BECAUSE NOW IT HAS STRANGE VIBRATION WHEN PRESSING THE BRAKE AND MAKES NOISE. AFTER ALL THIS ISSUES IS VERY HARD FOR ME AND I CAN FEEL SAFE DRIVING THE CAR.
NHTSA ODI #10746270
Official recalls
9Jan 15, 2019
Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to explode.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could explode with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 4, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V01.
May 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence & remedy
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Additional source detail variants (3)
Electrical System:software
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Vehicle Speed Control:cruise Control
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Electrical System:wiring
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Nov 21, 2017
Chrysler (FCA US LLC) is recalling certain 2014 Dodge Challenger, Charger, Durango, Chrysler 300, and Jeep Grand Cherokee vehicles equipped with a 3.6L engine and a 160 amp alternator. In the affected vehicles, the alternator may suddenly fail.
Consequence & remedy
Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the alternator, free of charge. The recall began December 15, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T75.
Jul 10, 2017
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Challenger, Dodge Charger, Chrysler 300, Dodge Durango, and 2012-2014 Jeep Grand Cherokee vehicles. The affected vehicles have electro-hydraulic power steering (EHPS) and are equipped with a 5.7L or a 3.6L engine and a 160, 180 or 220 amp alternator. In the affected vehicles, the alternator may suddenly fail.
Consequence & remedy
Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash. There is also the possibility that the alternator may short circuit, increasing the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will inspect the alternator and depending on the part number, will replace the alternator, if necessary, free of charge. The recall began February 12, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T36.
Feb 14, 2017
Chrysler (FCA US LLC) is recalling certain 2014-2017 Dodge Charger and Chrysler 300 vehicles equipped with all-wheel drive (AWD). The front driveshaft bolts may loosen and allow the front driveshaft to disconnect, potentially causing a loss of motive power.
Consequence & remedy
Consequence: A loss of motive power can increase the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace all eight front driveshaft bolts, free of charge. The recall began April 7, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T03.
Apr 25, 2016
Chrysler (FCA US LLC) is recalling certain model year 2012-2014 Dodge Charger and Chrysler 300 vehicles manufactured February 15, 2011, to November 27, 2014, and 2014-2015 Jeep Grand Cherokee vehicles manufactured July 16, 2012, to December 22, 2015. The affected vehicles, equipped with an eight-speed automatic transmission and a monostable gear selector, may not adequately warn the driver when driver's door is opened and the vehicle is not in PARK, allowing them to exit the vehicle while the vehicle is still in gear.
Consequence & remedy
Consequence: Drivers thinking that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.
Remedy: Chrysler will notify owners, and dealers will update the vehicle software to mitigate the risk of vehicle rollaway, free of charge. The recall began on June 24, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S27. Note: On October 19, 2016 Chrysler identified some previously repaired vehicles did not receive the complete software updates. Chrysler will renotify the affected owners, and dealers will update the software again.
Jan 28, 2016
FCA US LLC (Chrysler) is recalling certain model year 2011-2016 Dodge Charger vehicles manufactured August 23, 2010, to January 7, 2016. When an affected vehicle is lifted using the supplied tire jack without chocking the wheels, the vehicle's body-side sill may give causing the tire jack to fail and the car to fall.
Consequence & remedy
Consequence: A car that falls unexpectedly increases the risk of injury.
Remedy: Chrysler will notify owners, and dealers will provide owners with wheel chocks and instructions for their use, free of charge. The recall began on March 21, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S03.
Jul 27, 2015
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Charger vehicles manufactured May 6, 2010, to June 5, 2014. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence & remedy
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on August 25, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R35.
Additional source detail variants (2)
Seat Belts
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Charger vehicles manufactured May 6, 2010, to June 5, 2014. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on August 25, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R35.
Air Bags:side/window
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Charger vehicles manufactured May 6, 2010, to June 5, 2014. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on August 25, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R35.
Oct 8, 2014
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2014 Chrysler 300, Dodge Charger, Challenger, and Durango; and 2012-2014 Jeep Grand Cherokee vehicles manufactured April 22, 2010, to January 2, 2014, and equipped with a 3.6L engine and a 160 amp alternator. In the affected vehicles, the alternator may suddenly fail.
Consequence & remedy
Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash.
Remedy: Chrysler has notified owners, and dealers will replace the alternator, free of charge. The recall began on February 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P60.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA16002 · Vehicle Rollaway, Engine On
Opened Feb 3, 2016 · Closed Jun 24, 2016
Status: closed (inferred from source dates) · Power Train:automatic Transmission:gear Position Indication (prndl)
On April 22, 2016, Fiat Chrysler Automotive US LLC, (FCA) submitted a Defect Information Report (DIR) to NHTSA regarding a defect that could result in unattended vehicle rollaway with the engine running in approximately 811,586 model year (MY) 2012 to 2014 Dodge Charger and Chrysler 300 vehicles and MY 2014 to 2015 Jeep Grand Cherokee vehicles equipped with 8-speed transmissions and a monostable gear selector (NHTSA Recall #16V-240, FCA Recall #S27). According to FCA's DIR, The existing strategies built into these vehicles to deter drivers from exiting the vehicle after failing to put the transmission into PARK have not stopped some from doing so. Drivers erroneously concluding that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.The vehicles recalled by FCA are equipped with Monostable electronic (shift-by-wire) gearshift assemblies supplied by ZF Group (see Figure 1).The subject Monostable shifter has a single neutral position that it snaps back to when the driver releases the shift knob.Although the Monostable gearshift has the familiar appearance of a conventional console mechanical gearshift assembly, it has an unfamiliar movement that does not provide the tactile or visual feedback that drivers are accustomed to receiving from conventional shifters.Consequently, the driver must take additional time to verify that the desired gear position was achieved by checking the PRNDL display on the shift knob or the Electronic Vehicle Information Center (EVIC) display.
Additional source detail variants (2)
Power Train:automatic Transmission:gear Position Indication (prndl)
On April 22, 2016, Fiat Chrysler Automotive US LLC, (FCA) submitted a Defect Information Report (DIR) to NHTSA regarding a defect that could result in unattended vehicle rollaway with the engine running in approximately 811,586 model year (MY) 2012 to 2014 Dodge Charger and Chrysler 300 vehicles and MY 2014 to 2015 Jeep Grand Cherokee vehicles equipped with 8-speed transmissions and a monostable gear selector (NHTSA Recall #16V-240, FCA Recall #S27). According to FCA's DIR, The existing strategies built into these vehicles to deter drivers from exiting the vehicle after failing to put the transmission into PARK have not stopped some from doing so. Drivers erroneously concluding that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.The vehicles recalled by FCA are equipped with Monostable electronic (shift-by-wire) gearshift assemblies supplied by ZF Group (see Figure 1).The subject Monostable shifter has a single neutral position that it snaps back to when the driver releases the shift knob.Although the Monostable gearshift has the familiar appearance of a conventional console mechanical gearshift assembly, it has an unfamiliar movement that does not provide the tactile or visual feedback that drivers are accustomed to receiving from conventional shifters.Consequently, the driver must take additional time to verify that the desired gear position was achieved by checking the PRNDL display on the shift knob or the Electronic Vehicle Information Center (EVIC) display.
Power Train:automatic Transmission:gear Position Indication (prndl)
On April 22, 2016, Fiat Chrysler Automotive US LLC, (FCA) submitted a Defect Information Report (DIR) to NHTSA regarding a defect that could result in unattended vehicle rollaway with the engine running in approximately 811,586 model year (MY) 2012 to 2014 Dodge Charger and Chrysler 300 vehicles and MY 2014 to 2015 Jeep Grand Cherokee vehicles equipped with 8-speed transmissions and a monostable gear selector (NHTSA Recall #16V-240, FCA Recall #S27). According to FCA's DIR, The existing strategies built into these vehicles to deter drivers from exiting the vehicle after failing to put the transmission into PARK have not stopped some from doing so. Drivers erroneously concluding that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.The vehicles recalled by FCA are equipped with Monostable electronic (shift-by-wire) gearshift assemblies supplied by ZF Group (see Figure 1).The subject Monostable shifter has a single neutral position that it snaps back to when the driver releases the shift knob.Although the Monostable gearshift has the familiar appearance of a conventional console mechanical gearshift assembly, it has an unfamiliar movement that does not provide the tactile or visual feedback that drivers are accustomed to receiving from conventional shifters.Consequently, the driver must take additional time to verify that the desired gear position was achieved by checking the PRNDL display on the shift knob or the Electronic Vehicle Information Center (EVIC) display.
Illustration