NHTSA owner reports · September 18, 2026 snapshot.
Service Brakes complaints
40 reportsClear category filterMileage unknown · Jan 16, 2026
Electrical SystemForward Collision AvoidanceService Brakes
The Anti-Lock Brake module has prematurely failed in the vehicle. The dealership can and will inspect the fault but they will say they are not trained or authorizes to fix the module. I was directed to an ABS module rebuilder and was simply told by the rebuilder that they could not fix it due to a computer chip shortage. The pr…
Read full complaint
The Anti-Lock Brake module has prematurely failed in the vehicle. The dealership can and will inspect the fault but they will say they are not trained or authorizes to fix the module. I was directed to an ABS module rebuilder and was simply told by the rebuilder that they could not fix it due to a computer chip shortage. The problem has been reproduced many times as seen with the RAM truck recalls on their anti-lock brake modules. The component has not been inspected. There is active warning lights as shown in the picture below. Ive spun out in the rain multiple times at less than 30mph due to the ABS module not activating traction control. It is extremely dangerous.
NHTSA ODI #11711543
Mileage unknown · Jul 13, 2022
Air BagsFuel/propulsion SystemService Brakes
ABS Wiring had a recall and replaced but the ABS Module is now out Air Bag had a recall but now the air bag clock spring is out Fuel Pump had an extended warranty but is now out and fuel pump needs replaced Crank shaft main bearing seal needs rplaced for an oil leak but other parts have been replaced for an oil leak within the p…
Read full complaint
ABS Wiring had a recall and replaced but the ABS Module is now out Air Bag had a recall but now the air bag clock spring is out Fuel Pump had an extended warranty but is now out and fuel pump needs replaced Crank shaft main bearing seal needs rplaced for an oil leak but other parts have been replaced for an oil leak within the past month
NHTSA ODI #11473765
Mileage unknown · Jul 22, 2020
Electrical SystemElectronic Stability Control (esc)Service Brakes
WHILE DRIVING ON MAJORS HIGHWAY OR ROADS CAR JUST STALLS COMPLETELY THIS HAS HAPPENED NUMEROUS TIMES ALMOST
NHTSA ODI #11340918
53,000 miles · Oct 9, 2019
Service Brakes
BRAKE PEDAL OCCASIONALLY WILL GO TO THE FLOOR. NO WORK DONE THAT WOULD ALLOW AIR INTO THE SYSTEM. NO VISIBLE SIGNS OF A LEAK AND MASTER CYLINDER IS FULL OF FLUID. NO SPECIFIC DRIVING HABITS ARE EVIDENT WHEN FAILURE OCCURS. PROBLEM CORRECTS ITSELF WHEN PEDAL IS FORCIBLY DEPRESSED AND OCCURRENCE MAY NOT HAPPEN AGAIN FOR WEEKS OR M…
Read full complaint
BRAKE PEDAL OCCASIONALLY WILL GO TO THE FLOOR. NO WORK DONE THAT WOULD ALLOW AIR INTO THE SYSTEM. NO VISIBLE SIGNS OF A LEAK AND MASTER CYLINDER IS FULL OF FLUID. NO SPECIFIC DRIVING HABITS ARE EVIDENT WHEN FAILURE OCCURS. PROBLEM CORRECTS ITSELF WHEN PEDAL IS FORCIBLY DEPRESSED AND OCCURRENCE MAY NOT HAPPEN AGAIN FOR WEEKS OR MONTHS.
NHTSA ODI #11267306
62,426 miles · Dec 26, 2018
Service BrakesVehicle Speed Control
TL* THE CONTACT OWNS A 2011 DODGE CHARGER. WHILE DRIVING 40 MPH, THE VEHICLE ACCELERATED ON ITS OWN TO 90 MPH. THE ABS WOULD NOT RELEASE AND THE CONTACT HAD NO CONTROL OVER THE VEHICLE. THE CONTACT HAD TO APPLY MORE PRESSURE THAN USUAL TO THE BRAKE PEDAL TO STOP THE VEHICLE. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE DEAL…
Read full complaint
TL* THE CONTACT OWNS A 2011 DODGE CHARGER. WHILE DRIVING 40 MPH, THE VEHICLE ACCELERATED ON ITS OWN TO 90 MPH. THE ABS WOULD NOT RELEASE AND THE CONTACT HAD NO CONTROL OVER THE VEHICLE. THE CONTACT HAD TO APPLY MORE PRESSURE THAN USUAL TO THE BRAKE PEDAL TO STOP THE VEHICLE. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE DEALER WAS NOT CONTACTED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 62,426.
NHTSA ODI #11163454
82,000 miles · Mar 8, 2018
Service Brakes
TL* THE CONTACT OWNS A 2011 DODGE CHARGER. WHILE APPROACHING A STOP, THE CONTACT DEPRESSED THE BRAKE PEDAL AND THE PEDAL WOULD STICK TO THE FLOORBOARD. THE FAILURE WAS EXPERIENCED NUMEROUS TIMES. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE BRAKE PEDAL HAD TO BE DEPRESSED SEVERAL TIMES TO REGAIN BRAKE FUNCTION. THE VEHICLE …
Read full complaint
TL* THE CONTACT OWNS A 2011 DODGE CHARGER. WHILE APPROACHING A STOP, THE CONTACT DEPRESSED THE BRAKE PEDAL AND THE PEDAL WOULD STICK TO THE FLOORBOARD. THE FAILURE WAS EXPERIENCED NUMEROUS TIMES. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE BRAKE PEDAL HAD TO BE DEPRESSED SEVERAL TIMES TO REGAIN BRAKE FUNCTION. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC, BUT NO BRAKE FAILURES WERE FOUND. THE MECHANIC RECOMMENDED THAT THE ROTORS AND BRAKE PADS BE REPLACED. THE ROTORS AND BRAKE PADS WERE REPLACED, BUT THE FAILURE CONTINUED. THE DEALER WAS NOT CONTACTED. THE MANUFACTURER WAS NOTIFIED. THE APPROXIMATE FAILURE MILEAGE WAS 82,000.
NHTSA ODI #11076893
38,000 miles · Dec 18, 2017
Electrical SystemService BrakesStructure
TL* THE CONTACT OWNS A 2011 DODGE CHARGER. DUE TO EXCESSIVE BATTERY DRAIN, THE BATTERY HAD TO BE CHARGED APPROXIMATELY EVERY NINE DAYS. IN ADDITION, THE ABS WARNING INDICATOR ILLUMINATED. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBERS: 16V043000 (STRUCTURE) AND 17V435000 (ELECTRICAL SYSTEM). THE PARTS TO DO THE REPA…
Read full complaint
TL* THE CONTACT OWNS A 2011 DODGE CHARGER. DUE TO EXCESSIVE BATTERY DRAIN, THE BATTERY HAD TO BE CHARGED APPROXIMATELY EVERY NINE DAYS. IN ADDITION, THE ABS WARNING INDICATOR ILLUMINATED. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBERS: 16V043000 (STRUCTURE) AND 17V435000 (ELECTRICAL SYSTEM). THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. GILLIE HYDE DODGE CHRYSLER JEEP RAM (1415 HAPPY VALLEY RD, GLASGOW, KY) WAS CONTACTED AND CONFIRMED THAT THE PARTS WERE NOT AVAILABLE FOR THE RECALL REMEDY. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE AND WAS NOT ABLE TO CONFIRM WHEN THE PARTS WERE TO BECOME AVAILABLE. THE FAILURE MILEAGE WAS APPROXIMATELY 38,000. VIN TOOL CONFIRMS PARTS NOT AVAILABLE. *TL NEW ALTERNATOR WAS INSTALLED. CONSUMER STATED THERE ARE STILL PROBLEMS WITH ELECTRICAL ISSUES. UPDATED 8/30/18*JB
NHTSA ODI #11055262
93,000 miles · Dec 7, 2017
EngineService BrakesSteeringCrash
I DRIVE A 2011 DODGE CHARGER RT MY VEHICLE CONTINUES TO LOSS POWER AND WHEN POWER IS LOST I HAVE NO POWER STREERING OR BRAKES. I WAS ADVISED MY VEHICLE HAS A ACTIVE RECALL T-36 IN WHICH THE PROBLEMS I'M HAVE ARE A DIRECT RESULT OF THE RECALL. MY VEHICLE HAS BEEN IN THE SHOP MULTIPLE TIMES AT CLASSIC DODGE IN DENTON TX. THE ONLY …
Read full complaint
I DRIVE A 2011 DODGE CHARGER RT MY VEHICLE CONTINUES TO LOSS POWER AND WHEN POWER IS LOST I HAVE NO POWER STREERING OR BRAKES. I WAS ADVISED MY VEHICLE HAS A ACTIVE RECALL T-36 IN WHICH THE PROBLEMS I'M HAVE ARE A DIRECT RESULT OF THE RECALL. MY VEHICLE HAS BEEN IN THE SHOP MULTIPLE TIMES AT CLASSIC DODGE IN DENTON TX. THE ONLY THING CLASSIC DODGE HAS DONE IS REPLACE THE BATTERY STATING WE HAD TO START THERE AND ADVISED ME FCA HAS NOT SENT OUT A FIX AND WONT UNTIL FEB 2018. I HAVE REPORTED TO CLASSIC DODGE IN DENTON AS WELL AS MY FCA CASE MANAGER MY VEHICLE CONTINUES TO LOSS POWER AND HAS ALMOST RESULTED IN SEVERAL CRASHES AND FCA HAS FAILED TO RESOLVE THE PROBLEM AND HAS STOPPED RETURNING MY PHONE CALLS. ON 12-05-17 I WAS INVOLVED IN A AUTOMOBLE CRASH IN THE CHARGER CAUSED BY THE LOSS IN POWER AND I RAN INTO A TREE CAUSING VEHICLE STRUCTUAL DAMAGE.
NHTSA ODI #11052954
119,000 miles · Oct 5, 2017
Service Brakes
ON FOUR SEPARATE OCCASIONS, MY BRAKES HAVE SLIPPED AND THE PEDAL HAS GONE STRAIGHT TO THE FLOOR. THREE TIMES AS I WAS ROLLING SLOWLY UP TO AN ATM MACHINE. THE 4TH TIME WHILE I WAS SLOWING DOWN TO A STOP LIGHT, GOING APPX 30 MPH. I JUST HAD NEW FRONT BRAKES PUT ON. I WAS TOLD THE BACK BRAKES ARE STILL 3/4 PAD LEFT. I TOLD TH…
Read full complaint
ON FOUR SEPARATE OCCASIONS, MY BRAKES HAVE SLIPPED AND THE PEDAL HAS GONE STRAIGHT TO THE FLOOR. THREE TIMES AS I WAS ROLLING SLOWLY UP TO AN ATM MACHINE. THE 4TH TIME WHILE I WAS SLOWING DOWN TO A STOP LIGHT, GOING APPX 30 MPH. I JUST HAD NEW FRONT BRAKES PUT ON. I WAS TOLD THE BACK BRAKES ARE STILL 3/4 PAD LEFT. I TOLD THE MECHANIC OF THE SLIPPING AND HE SAID THEY CHECKED ALL THINGS THAT USUALLY CAUSE THIS AND ALL THOSE AREAS ARE FULLY SEALED AND LOOK GOOD. THEY CAN'T FIND ANY REASON FOR THIS TO BE HAPPENING.
NHTSA ODI #11031955
70,000 miles · Aug 7, 2017
EnginePower TrainService Brakes
TL* THE CONTACT OWNS A 2011 DODGE CHARGER. WHILE DRIVING 45 MPH, THE ABS, TRACTION CONTROL, AND SERVICE AWD INDICATORS ILLUMINATED WITHOUT WARNING IN THE MIDDLE OF AN INTERSECTION. ALSO, THE TRANSMISSION SLIPPED, WHICH CAUSED THE VEHICLE TO STALL. ALSO, WHILE THE VEHICLE WAS STATIONARY, THE EMERGENCY BRAKE INDICATOR ILLUMINATED …
Read full complaint
TL* THE CONTACT OWNS A 2011 DODGE CHARGER. WHILE DRIVING 45 MPH, THE ABS, TRACTION CONTROL, AND SERVICE AWD INDICATORS ILLUMINATED WITHOUT WARNING IN THE MIDDLE OF AN INTERSECTION. ALSO, THE TRANSMISSION SLIPPED, WHICH CAUSED THE VEHICLE TO STALL. ALSO, WHILE THE VEHICLE WAS STATIONARY, THE EMERGENCY BRAKE INDICATOR ILLUMINATED AND THE TRANSMISSION SLIPPED. THE CONTACT STATED THAT THE ABS INDICATOR DISENGAGED AND THE VEHICLE WAS ABLE TO BE DRIVEN AWAY AT LOWER SPEEDS OF 20-25 MPH. THE DEALER AND MANUFACTURER WERE NOT NOTIFIED. THE FAILURE MILEAGE WAS 70,000.
NHTSA ODI #11013501
Official recalls
11Jan 15, 2019
Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to explode.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could explode with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 4, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V01.
Jan 9, 2018
Chrysler (FCA US LLC) is recalling certain 2009-2013 Jeep Wrangler, Chrysler 300, Dodge Challenger and Dodge Charger vehicles, and 2009-2011 Dodge Dakota vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Chrysler is recalling certain 2009-2010 RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Chrysler is also recalling certain 2009 RAM 3500, RAM 2500, RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, Dodge Durango, Chrysler Aspen, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U03.
Jul 10, 2017
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Challenger, Dodge Charger, Chrysler 300, Dodge Durango, and 2012-2014 Jeep Grand Cherokee vehicles. The affected vehicles have electro-hydraulic power steering (EHPS) and are equipped with a 5.7L or a 3.6L engine and a 160, 180 or 220 amp alternator. In the affected vehicles, the alternator may suddenly fail.
Consequence & remedy
Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash. There is also the possibility that the alternator may short circuit, increasing the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will inspect the alternator and depending on the part number, will replace the alternator, if necessary, free of charge. The recall began February 12, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T36.
May 24, 2016
Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.
Consequence & remedy
Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.
Jan 28, 2016
FCA US LLC (Chrysler) is recalling certain model year 2011-2016 Dodge Charger vehicles manufactured August 23, 2010, to January 7, 2016. When an affected vehicle is lifted using the supplied tire jack without chocking the wheels, the vehicle's body-side sill may give causing the tire jack to fail and the car to fall.
Consequence & remedy
Consequence: A car that falls unexpectedly increases the risk of injury.
Remedy: Chrysler will notify owners, and dealers will provide owners with wheel chocks and instructions for their use, free of charge. The recall began on March 21, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S03.
Jul 27, 2015
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Charger vehicles manufactured May 6, 2010, to June 5, 2014. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence & remedy
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on August 25, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R35.
Additional source detail variants (2)
Seat Belts
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Charger vehicles manufactured May 6, 2010, to June 5, 2014. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on August 25, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R35.
Air Bags:side/window
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Charger vehicles manufactured May 6, 2010, to June 5, 2014. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on August 25, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R35.
Oct 8, 2014
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2014 Chrysler 300, Dodge Charger, Challenger, and Durango; and 2012-2014 Jeep Grand Cherokee vehicles manufactured April 22, 2010, to January 2, 2014, and equipped with a 3.6L engine and a 160 amp alternator. In the affected vehicles, the alternator may suddenly fail.
Consequence & remedy
Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash.
Remedy: Chrysler has notified owners, and dealers will replace the alternator, free of charge. The recall began on February 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P60.
Mar 4, 2014
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2012 Dodge Charger vehicles manufactured May 20, 2010, through November 8, 2011, and equipped with halogen headlamps. In the affected vehicles, a sub-harness for the headlights may overheat and cause the low beam headlights to go out.
Consequence & remedy
Consequence: Loss of headlights reduces the driver's visibility, increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the headlamp jumper harnesses and bulbs, or the headlamp assemblies, as necessary, free of charge. The recall began on May 2, 2014. Owners may contract Chrysler at 1-800-853-1403. Chrysler's number associated with this recall is P08. This recall concerns non-police vehicles. A separate campaign was launched in 2012 to address police vehicles. See NHTSA recall 12V-042.
Apr 3, 2013
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2012 Chrysler 300, Dodge Challenger, and Dodge Charger vehicles manufactured April 11, 2011, through December 14, 2011. The affected vehicles may have improperly sized terminal crimps on the seat side-airbag wiring harness which may cause the seat side-airbags to malfunction and illuminate the airbag warning light.
Consequence & remedy
Consequence: In the event of a crash necessitating airbag deployment the airbags may not operate as designed, increasing the risk of injury.
Remedy: Chrysler will notify owners, and dealers will replace both driver and passenger seat airbag wiring harnesses, free of charge. The recall began on April 22, 2013. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N07.
May 2, 2012
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 300 AND DODGE CHARGER VEHICLES. THESE VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence & remedy
Consequence: THIS COULD LEAD TO LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS, AND DEALERS WILL RELOCATE THE ABS/ESC SYSTEM FUSE, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 18, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Additional source detail variants (2)
Electrical System:wiring:fuses And Circuit Breakers
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 300 AND DODGE CHARGER VEHICLES. THESE VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence: THIS COULD LEAD TO LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS, AND DEALERS WILL RELOCATE THE ABS/ESC SYSTEM FUSE, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 18, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Service Brakes, Air:antilock:control Unit/module
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 300 AND DODGE CHARGER VEHICLES. THESE VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence: THIS COULD LEAD TO LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS, AND DEALERS WILL RELOCATE THE ABS/ESC SYSTEM FUSE, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 18, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Feb 7, 2012
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 and 2012 DODGE CHARGER POLICE VEHICLES. THE LOW BEAM HEADLAMPS OF SOME VEHICLES COULD FAIL DUE TO AN OVERHEATED BULB HARNESS CONNECTOR. OTHER VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence & remedy
Consequence: THIS COULD LEAD TO LOSS OF VISIBILITY AND/OR BRAKING ABILITY, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL REPLACE THE HEADLAMP JUMPER HARNESSES AND RELOCATE THE ABS/ESC SYSTEM FUSE WITHIN THE POWER DISTRIBUTION CENTER, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 2, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Additional source detail variants (4)
Electrical System:wiring:fuses And Circuit Breakers
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 and 2012 DODGE CHARGER POLICE VEHICLES. THE LOW BEAM HEADLAMPS OF SOME VEHICLES COULD FAIL DUE TO AN OVERHEATED BULB HARNESS CONNECTOR. OTHER VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence: THIS COULD LEAD TO LOSS OF VISIBILITY AND/OR BRAKING ABILITY, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL REPLACE THE HEADLAMP JUMPER HARNESSES AND RELOCATE THE ABS/ESC SYSTEM FUSE WITHIN THE POWER DISTRIBUTION CENTER, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 2, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Exterior Lighting:headlights
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 and 2012 DODGE CHARGER POLICE VEHICLES. THE LOW BEAM HEADLAMPS OF SOME VEHICLES COULD FAIL DUE TO AN OVERHEATED BULB HARNESS CONNECTOR. OTHER VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence: THIS COULD LEAD TO LOSS OF VISIBILITY AND/OR BRAKING ABILITY, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL REPLACE THE HEADLAMP JUMPER HARNESSES AND RELOCATE THE ABS/ESC SYSTEM FUSE WITHIN THE POWER DISTRIBUTION CENTER, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 2, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Electrical System:wiring
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 and 2012 DODGE CHARGER POLICE VEHICLES. THE LOW BEAM HEADLAMPS OF SOME VEHICLES COULD FAIL DUE TO AN OVERHEATED BULB HARNESS CONNECTOR. OTHER VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence: THIS COULD LEAD TO LOSS OF VISIBILITY AND/OR BRAKING ABILITY, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL REPLACE THE HEADLAMP JUMPER HARNESSES AND RELOCATE THE ABS/ESC SYSTEM FUSE WITHIN THE POWER DISTRIBUTION CENTER, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 2, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 and 2012 DODGE CHARGER POLICE VEHICLES. THE LOW BEAM HEADLAMPS OF SOME VEHICLES COULD FAIL DUE TO AN OVERHEATED BULB HARNESS CONNECTOR. OTHER VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence: THIS COULD LEAD TO LOSS OF VISIBILITY AND/OR BRAKING ABILITY, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL REPLACE THE HEADLAMP JUMPER HARNESSES AND RELOCATE THE ABS/ESC SYSTEM FUSE WITHIN THE POWER DISTRIBUTION CENTER, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 2, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE14022 · Alternator Failure
Opened Jul 22, 2014 · Closed Nov 6, 2014
Status: closed (inferred from source dates) · Electrical System:alternator/generator/regulator
On July 22, 2014, the Office of Defects Investigation (ODI) opened PE14-022 to investigate 14 complaints (VOQs) alleging incidents of alternator failure resulting in engine stall while driving in model year (MY) 2011 through 2012 Dodge Charger vehicles.The MY 2011 through 2012 Dodge Charger vehicles were sold with three different engine options:1) 3.6L V6 (VIN8 = G), 88,766 vehicles; 2) 5.7L V8 (VIN8 = T), 38,615 vehicles; and 3) 6.4L V8 (VIN8 = J), 2,406 MY 2012 vehicles.The 14 VOQs identified in the PE14-022 opening resume involve 13 vehicles with 3.6L V6 engines and 1 vehicle with unknown engine (no VIN provided).In an October 7, 2014 letter to NHTSA, Chrysler described a safety defect condition that could result in rapid alternator failure having limited or no detection in approximately 434,581 MY 2011 through 2014 Chrysler 300, Dodge Charger, Dodge Challenger, Dodge Durango and Jeep Grand Cherokee vehicles equipped with 3.6L engines and 160 amp alternators (NHTSA Recall No. 14V-634, Chrysler P60).The subject alternators are used in vehicles equipped with 3.6L V6 engines and without towing packages.According to Chrysler, the silicone diodes in the alternator rectifier bridge may experience thermal fatigue due to cyclic loading from the Electric Hydraulic Power Steering (EHPS) system, eventually resulting in no output, reduced output, or a fully shorted to ground condition.These failure modes vary in their time to failure and warning to the driver.Depending on the failure mode and timing, system voltage may drop to critically low levels, disabling systems such as the Anti-lock Brake System/Electronic Stability Control, Engine Control Module/Central Body Controller, or a total vehicle electrical system shut down (in the event of a short to ground failure mode).Analysis of complaints to ODI and Chrysler identified a total of 146 incidents of alternator failure resulting in engine stall while driving in MY 2011 through 2012 Dodge Charger vehicles, including 142 involving vehicles equipped with the 3.6L V6 engines (1.6 IPTV) that were included in 14V-634 and 4 involving vehicles with 5.7L V8 engines (0.1 IPTV), which are equipped with different alternators.Analysis of all alternator failure complaints found that approximately 48 percent of VOQs and 21 percent of Chrysler complaints involved allegations of engine stall.Many (98) complaints reported fire and/or smoke, but analysis of these determined that they involved thermal damage to the alternator diode and did not identify any incidents involving damage beyond the alternator assembly.One VOQ identified in the opening resume for PE14-022 alleged a crash, but further evaluation determined that this involved a minor rear-end impact with slight bumper damage.This investigation is closed based on Chrysler's decision to conduct a safety recall.The VOQs associated with this investigation are:10641479,10641366,10641349,10642017,10640770,10640687,10640553,10639692,10638810,10638356,10638175,10638143,10637460,10633806,10633304,10632943,10632006,10631704,10631613,10631420,10631088,10630991,10630854,10630844,10630108,10629623,10629603,10628228,10628150,10627941,10627342,10626452,10626254,10625962,10622385,10622340,10621603,10620961,10619481,10618950,10618948,10618539,10618476,10618334,10618081,10618107,10616834,10616461,10616456,10615754,10615719,10606580,10605090,10604958,10597295,10592085,10588675,10587141,10562463,10559730,10511407
Illustration