IllustrationMY KEY WILL NOT COME OUT OF THE IGNITION AFTER RUNNING THE CAR. I HAVE TO PULL OUT THE FUSE #8 IN THE TRUNK AND I HEAR A CLICK AND IT RESETS AND THEN I CAN GET THE KEY OUT OF THE IGNITION TURNING IT TO THE LEFT.
2010 Dodge Charger
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all Charger years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
280–25K
2025–50K
2450–75K
2075–100K
40100–150K
18150K+
150 reports with mileage · 82 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 74 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 59 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 48 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
14 crash reports9 fire reports5 injury reports
What owners actually said
232 reportsTHE WINN MODULE
TL* THE CONTACT OWNS A 2010 DODGE CHARGER. WHILE THE VEHICLE WAS AT CRONIC CHRYSLER DODGE JEEP RAM (2515 N EXPY, GRIFFIN, GA 30223, (770) 227-4271) FOR MAINTENANCE, THE MECHANIC INFORMED THE CONTACT THAT THE TIRES WERE UNABLE TO BE ROTATED BECAUSE THE LUG NUTS WERE SWOLLEN. THE CONTACT WAS UNABLE TO REMOVE THE LUG NUTS WITH THE …
Read full complaint
TL* THE CONTACT OWNS A 2010 DODGE CHARGER. WHILE THE VEHICLE WAS AT CRONIC CHRYSLER DODGE JEEP RAM (2515 N EXPY, GRIFFIN, GA 30223, (770) 227-4271) FOR MAINTENANCE, THE MECHANIC INFORMED THE CONTACT THAT THE TIRES WERE UNABLE TO BE ROTATED BECAUSE THE LUG NUTS WERE SWOLLEN. THE CONTACT WAS UNABLE TO REMOVE THE LUG NUTS WITH THE TIRE TOOL BECAUSE THE NUTS EXPANDED AND COULD FRACTURE IF ATTEMPTED TO BE REMOVED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 122,000.
SAFETY RECALL K08. WIRELESS IGNITION NODE KEY FALLS OUT OF IGNITION, CAR KEEPS RUNNING, CAN'T SHUT OFF UNLESS DISCONNECT BATTERY. CAR ALSO SHUTS OFF BY ITSELF AT TIMES IN THE MIDDLE OF TRAFFIC. PURCHASED CAR ABOUT TWO YEARS AGO. DEALER WANTS TO CHARGE $1250 TO FIX IT BECAUSE CAR NOT SHOWING ANY OPEN RECALLS. MAY HAVE BEEN FI…
Read full complaint
SAFETY RECALL K08. WIRELESS IGNITION NODE KEY FALLS OUT OF IGNITION, CAR KEEPS RUNNING, CAN'T SHUT OFF UNLESS DISCONNECT BATTERY. CAR ALSO SHUTS OFF BY ITSELF AT TIMES IN THE MIDDLE OF TRAFFIC. PURCHASED CAR ABOUT TWO YEARS AGO. DEALER WANTS TO CHARGE $1250 TO FIX IT BECAUSE CAR NOT SHOWING ANY OPEN RECALLS. MAY HAVE BEEN FIXED ONE TIME BEFORE WE PURCHASED IT BUT IT IS DOING EXACTLY WHAT RECALL PROBLEM IS RIGHT NOW. NOT SURE IF IT WAS EVER TAKEN CARE OF.
THE VEHICLE CAUGHT FIRE WHILE I WAS SITTING WITH MY CAR RUNNING PARKED.
TL* THE CONTACT OWNS A 2010 DODGE CHARGER. WHEN THE VEHICLE WAS STARTED AND THE ACCELERATOR PEDAL WAS DEPRESSED, AN ABNORMAL WINDING NOISE WAS HEARD AND THE BATTERY WARNING INDICATOR ILLUMINATED. ALSO, WHILE DRIVING VARIOUS SPEEDS, THE VEHICLE STALLED AND THE CHECK ENGINE INDICATOR ILLUMINATED. THE VEHICLE WAS NOT TAKEN TO A DEA…
Read full complaint
TL* THE CONTACT OWNS A 2010 DODGE CHARGER. WHEN THE VEHICLE WAS STARTED AND THE ACCELERATOR PEDAL WAS DEPRESSED, AN ABNORMAL WINDING NOISE WAS HEARD AND THE BATTERY WARNING INDICATOR ILLUMINATED. ALSO, WHILE DRIVING VARIOUS SPEEDS, THE VEHICLE STALLED AND THE CHECK ENGINE INDICATOR ILLUMINATED. THE VEHICLE WAS NOT TAKEN TO A DEALER OR INDEPENDENT MECHANIC FOR DIAGNOSTIC TESTING OR REPAIRS. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURES. THE FAILURE MILEAGE WAS 130,000.
RECENTLY I HAVE CHANGED THE BATTERY, ALTERNATOR, AND NOW THE CAR IS AT THE DEALERSHIP AND THEY CHANGED SOME TYPE OF MODULE THAT READS THE KEYS, FIRST THEY STATED THE FUSE BOX IN THE TRUNK WAS THE PROBLEM. THEY INSTALLED A NEW FUSE BOX AND THEY THEN STATED THAT WAS NOT THE PROBLEM. NEXT IS WHEN THEY REPLACED THE MODULE THAT RE…
Read full complaint
RECENTLY I HAVE CHANGED THE BATTERY, ALTERNATOR, AND NOW THE CAR IS AT THE DEALERSHIP AND THEY CHANGED SOME TYPE OF MODULE THAT READS THE KEYS, FIRST THEY STATED THE FUSE BOX IN THE TRUNK WAS THE PROBLEM. THEY INSTALLED A NEW FUSE BOX AND THEY THEN STATED THAT WAS NOT THE PROBLEM. NEXT IS WHEN THEY REPLACED THE MODULE THAT READS THE KEYS, AND THEN THEY STATED THAT ALL THE FUSES WERE BLOWN AND THERE HAD TO BE A POWER SURGE THERE WAS NOT. I DON'T UNDERSTAND WHY THEY DIDN'T SEE THE BLOWN FUSES WHEN THEY STARTED THIS WHOLE PROCESS. ALSO, THEY STATED THAT THERE IS A RECALL ON 2010 DODGE CHARGERS WITH THE MODULE THAT CONTROLS THE KEYS HOWEVER MY CAR WAS 10 DAYS OUTSIDE OF THE BUILD DATE TO QUALIFY. WHAT IS GOING AND WHY WOULD MY CAR BE OUTSIDE THE BUILD DATE? THEY STATED THAT THEY DON'T KNOW WHAT THE ISSUE IS NOW. THE OFFICIAL DODGE DEALERSHIP HAS MY CAR AND THEY DON'T KNOW WHAT THE ISSUE IS.
TL* THE CONTACT OWNS A 2010 DODGE CHARGER. WHILE DRIVING 60 MPH, THE THROTTLE BODY AND ELECTRIC POWER STEERING WARNING INDICATORS ILLUMINATED. AFTERWARDS, THE VEHICLE AUTOMATICALLY SLOW DOWN FROM 60 TO 40 MPH. GRAINGER HONDA (1596 CHATHAM PKWY, SAVANNAH, GA 31408, (888) 229-4632) DIAGNOSED THE VEHICLE, BUT COULD NOT FIND A FAILU…
Read full complaint
TL* THE CONTACT OWNS A 2010 DODGE CHARGER. WHILE DRIVING 60 MPH, THE THROTTLE BODY AND ELECTRIC POWER STEERING WARNING INDICATORS ILLUMINATED. AFTERWARDS, THE VEHICLE AUTOMATICALLY SLOW DOWN FROM 60 TO 40 MPH. GRAINGER HONDA (1596 CHATHAM PKWY, SAVANNAH, GA 31408, (888) 229-4632) DIAGNOSED THE VEHICLE, BUT COULD NOT FIND A FAILURE. THE CONTACT BELIEVED THE FAILURE WAS DUE TO THE ELECTRICAL SYSTEM. THE MANUFACTURER WAS NOT NOTIFIED. THE VIN WAS UNKNOWN. THE FAILURE MILEAGE WAS 92,000.
I'VE HAD A RECURRING ISSUE WITH A FUEL SMELL IN MY VEHICLE . TURNS OUT MOST DODGE CHARGERS HAVE DEFECTIVE FUEL PUMPS AND LUCKY US THERE ARE 2 AT ALMOST 700 DOLLARS TOGETHER FROM NAPA . WHY HASN'T THIS ISSUE BEEN RECALLED? IT CAN CAUSE MAJOR DAMAGE TO THE ENGINE IF FUEL GETS IN THE OIL. MAJOR SAFETY CONCERN GAS VAPORS SHOULD NEV…
Read full complaint
I'VE HAD A RECURRING ISSUE WITH A FUEL SMELL IN MY VEHICLE . TURNS OUT MOST DODGE CHARGERS HAVE DEFECTIVE FUEL PUMPS AND LUCKY US THERE ARE 2 AT ALMOST 700 DOLLARS TOGETHER FROM NAPA . WHY HASN'T THIS ISSUE BEEN RECALLED? IT CAN CAUSE MAJOR DAMAGE TO THE ENGINE IF FUEL GETS IN THE OIL. MAJOR SAFETY CONCERN GAS VAPORS SHOULD NEVER BE IN CABIN !!!!
TL* THE CONTACT OWNS A 2010 DODGE CHARGER. WHILE DRIVING 55 MPH, THE CHECK ENGINE INDICATOR ILLUMINATED AND THE VEHICLE LOST POWER. THE VEHICLE WAS TOWED TO THE CONTACT'S RESIDENCE. THE VEHICLE WAS NOT TAKEN TO A DEALER OR INDEPENDENT MECHANIC FOR DIAGNOSTIC TESTING OR REPAIRS. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE.…
Read full complaint
TL* THE CONTACT OWNS A 2010 DODGE CHARGER. WHILE DRIVING 55 MPH, THE CHECK ENGINE INDICATOR ILLUMINATED AND THE VEHICLE LOST POWER. THE VEHICLE WAS TOWED TO THE CONTACT'S RESIDENCE. THE VEHICLE WAS NOT TAKEN TO A DEALER OR INDEPENDENT MECHANIC FOR DIAGNOSTIC TESTING OR REPAIRS. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 152,000.
Official recalls
619V018000 · Air Bags:frontal:passenger Side:inflator Module
Jan 15, 2019
Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to explode.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could explode with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 4, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V01.
18V021000 · Air Bags:frontal:passenger Side:inflator Module
Jan 9, 2018
Chrysler (FCA US LLC) is recalling certain 2009-2013 Jeep Wrangler, Chrysler 300, Dodge Challenger and Dodge Charger vehicles, and 2009-2011 Dodge Dakota vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Chrysler is recalling certain 2009-2010 RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Chrysler is also recalling certain 2009 RAM 3500, RAM 2500, RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, Dodge Durango, Chrysler Aspen, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U03.
16V352000 · Air Bags:frontal:passenger Side:inflator Module
May 24, 2016
Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.
Consequence & remedy
Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.
15V313000 · Air Bags:frontal:driver Side:inflator Module
May 26, 2015
Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.
10V200000 · Electrical System:ignition:module
May 11, 2010
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2010 CHRYSLER 300, DODGE CHALLENGER, CHARGER, JEEP COMMANDER, GRAND CHEROKEE AND DODGE RAM VEHICLES. THESE VEHICLES MAY HAVE BEEN BUILT WITH A WIRELESS IGNITION NODE (WIN) MODULE EXHIBITING A BINDING CONDITION OF THE SOLENOID LATCH.
Consequence & remedy
Consequence: THE RESULT OF THE DEFECT COULD LEAD TO A CONDITION WHERE THE KEY MAY BE REMOVED FROM THE IGNITION SWITCH (WIN MODULE) PRIOR TO PLACING THE SHIFTER IN PARK. THIS COULD RESULT IN THE POTENTIAL FOR UNINTENDED VEHICLE MOVEMENT AND COULD INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL INSPECT AND REPLACE THE WIN MODULE FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE AUGUST 23, 2010. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
09V420000 · Wheels:lugs/nuts/bolts/studs
Oct 29, 2009
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2009 THROUGH 2010 PASSENGER VEHICLES EQUIPPED WITH REAR WHEEL DRIVE. THESE VEHICLES MAY HAVE BEEN BUILT WITHOUT A FRONT WHEEL SPINDLE NUT.
Consequence & remedy
Consequence: WHILE DRIVING, A TIRE AND WHEEL SEPARATION COULD OCCUR INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL INSPECT THE TIRE AND WHEEL ASSEMBLY AND IF FOUND WITHOUT A SPINDLE NUT IT WILL BE REPAIRED FREE OF CHARGE. THE RECALL BEGAN ON NOVEMBER 2, 2009. OWNERS MAY CONTACT CHRYSLER AT 1-800-835-1403.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.