← New search

2009 Dodge Charger

Owner reports · Recalls · Investigations

Limited comparison data

There is not enough comparable history to draw a useful model-year comparison.

About this comparison →

When problems were reported

Mileage at the reported incident

124 reports with mileage · 50 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 45 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 45 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 32 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

9 crash reports4 fire reports8 injury reports

Fuel System, Gasoline complaints

1 reports
Clear category filter
14,000 miles · Feb 24, 2010
Fuel System, GasolinePower TrainSuspension

. "SPORADIC" PROBLEM WITH THE CAR DEVELOPING A VIOLENT SHAKE WHEN TRAVELING BETWEEN 50-70MPH. PROBLEM HAS ONLY BEEN DETECTED SPORADICALLY WHEN GOING UP/DOWN INCLINES ON INTERSTATE. CAR LOSES MOMENTUM WHEN PROBLEM OCCURS REQUIRING ME TO COMPLETELY LET OFF GAS AND DROP CAR INTO NEUTRAL TO REGAIN MOMENTUM. CANNOT RECREATE PROBLE…

Read full complaint

. "SPORADIC" PROBLEM WITH THE CAR DEVELOPING A VIOLENT SHAKE WHEN TRAVELING BETWEEN 50-70MPH. PROBLEM HAS ONLY BEEN DETECTED SPORADICALLY WHEN GOING UP/DOWN INCLINES ON INTERSTATE. CAR LOSES MOMENTUM WHEN PROBLEM OCCURS REQUIRING ME TO COMPLETELY LET OFF GAS AND DROP CAR INTO NEUTRAL TO REGAIN MOMENTUM. CANNOT RECREATE PROBLEM AT WILL, ONLY OCCURS SPORADICALLY. . PROBLEM HAS OCCURRED OVER 20 TIMES SINCE MID DECEMBER 2009 . CAR HAS BEEN TAKEN ON 7 SEPARATE OCCASIONS TO LOCAL DODGE DEALERSHIP WHERE PURCHASED (BOB FRENSLEY CHRSYLER/DODGE). FIVE OF THESE OCCASIONS INVOICABLE WORK WAS PERFORMED AS NOTED BELOW. DEALERSHIP CLAIMS THEY CAN NO LONGER RECREATE THE PROBLEM AND REFUSE TO WORK ON THE CAR ANY LONGER . PROBLEM HAS BEEN REPORTED TO DODGE CUSTOMER CARE WITH 2 SEPARATE CASES BEING OPENED. DODGE CUSTOMER CARE REFUSES TO AUTHORIZE ANY FURTHER WORK UNLESS THE DEALERSHIP ACKNOWLEDGES THAT THEY CAN RECREATE THE PROBLEM. . BOTH DODGE CUSTOMER CARE AND THE DEALERSHIP HAVE VERBALLY RECOMMENDED THE FOLLOWING SOLUTION: "CONTINUE TO DRIVE THE CAR UNTIL THE PROBLEM WORSENS AND THEN BRING IT BACK TO BE SERVICED". . EACH TIME THE CAR HAS BEEN RETURNED TO ME THE PROBLEM HAS RECURRED WITHIN 3 DAYS INVOICES: #1 (01/08/2010) . REPLACED FUEL INJECTOR DUE TO P0304 CODE CYLINDER #4 MISFIRE . REPLACE LEFT REAR TIRE DUE TO NAIL IN TIRE (COVERED BY EXTENDED WARRANTY) #2 (01/18/2010) . FLASH UPGRADE TORQUE CONVERTER (PERFORMED, NOT LISTED ON INVOICE) . WHEEL BALANCE (BOTH FRONT, BOTH REAR) . MOUNT MATCH WHEEL TO TIRE (EACH WHEEL) #3 (01/26/2010) . REPLACED TORQUE CONVERTER . REMOVE AND REPOSITION MOLDING/WINDSHIELD A-PILLAR #4 (02/12/2010) . FLASH UPGRADE TORQUE CONVERTER (PERFORMED, NOT LISTED ON INVOICE) . REPLACE 4 LOW TIRE PRESSURE SENSORS . CROSS SWITCH ALL TIRES . FRONT END/REAR WHEEL ALIGNMENT #5 (02/22/2010) . ADDED ANTIFRICTION MODIFIER TO TRANSMISSION . TEST DROVE VEHICLE AND COULD NOT RECREATE PROBLEM. *TR

NHTSA ODI #10313491

Official recalls

6

18V021000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2018

Chrysler (FCA US LLC) is recalling certain 2009-2013 Jeep Wrangler, Chrysler 300, Dodge Challenger and Dodge Charger vehicles, and 2009-2011 Dodge Dakota vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Chrysler is recalling certain 2009-2010 RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Chrysler is also recalling certain 2009 RAM 3500, RAM 2500, RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, Dodge Durango, Chrysler Aspen, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U03.

16V352000 · Air Bags:frontal:passenger Side:inflator Module

May 24, 2016

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Consequence & remedy

Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

15V313000 · Air Bags:frontal:driver Side:inflator Module

May 26, 2015

Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.

09V420000 · Wheels:lugs/nuts/bolts/studs

Oct 29, 2009

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2009 THROUGH 2010 PASSENGER VEHICLES EQUIPPED WITH REAR WHEEL DRIVE. THESE VEHICLES MAY HAVE BEEN BUILT WITHOUT A FRONT WHEEL SPINDLE NUT.

Consequence & remedy

Consequence: WHILE DRIVING, A TIRE AND WHEEL SEPARATION COULD OCCUR INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE TIRE AND WHEEL ASSEMBLY AND IF FOUND WITHOUT A SPINDLE NUT IT WILL BE REPAIRED FREE OF CHARGE. THE RECALL BEGAN ON NOVEMBER 2, 2009. OWNERS MAY CONTACT CHRYSLER AT 1-800-835-1403.

08V642000 · Tires:pressure Monitoring And Regulating Systems

Dec 5, 2008

CHRYSLER IS RECALLING 175 MY 2009 DODGE CHARGER, CHALLENGER, AND CHRYSLER 300 VEHICLES. THE TIRE PRESSURE MONITOR (TPM) SENSORS MAY NOT TRANSMIT THE ACTUAL TIRE PRESSURE. THIS COULD RESULT IN THE DRIVER NOT BEING AWARE OF LOW TIRE PRESSURE.

Consequence & remedy

Consequence: OPERATION OF THE VEHICLE WITH LOW TIRE PRESSURE COULD RESULT IN TIRE DAMAGE AND CAUSE A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL REPLACE THE TPM SENSORS. THE RECALL IS EXPECTED TO BEGIN ON FEBRUARY 9, 2009. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

08V583000 · Power Train:automatic Transmission:lever And Linkage:column Shift

Nov 6, 2008

CHRYSLER IS RECALLING 20,283 MY 2006-2009 CHARGER AND MAGNUM VEHICLES BUILT WITH THE POLICE PACKAGE AND EQUIPPED WITH A COLUMN SHIFTER. THE GEARSHIFT CABLE MAY BECOME DISENGAGED FROM THE STEERING COLUMN MOUNTING BRACKET AND CAUSE AN INCORRECT TRANSMISSION GEARSHIFT POSITION DISPLAY.

Consequence & remedy

Consequence: THIS COULD ALLOW THE VEHICLE TO MOVE IN AN UNEXPECTED DIRECTION STARTLING THE DRIVER, AND CAUSE A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL ADD A REDUNDANT LOCKING MECHANISM TO THE GEARSHIFT CABLE AT THE MOUNTING BRACKET TO ENSURE PROPER RETENTION AND SHIFT LINKAGE FUNCTION. THE RECALL BEGAN ON NOVEMBER 10, 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

PE08052 · Prndl Misalignment

Opened Sep 2, 2008 · Closed Nov 10, 2008

Status: closed (inferred from source dates) · Power Train:automatic Transmission:lever And Linkage:column Shift

IN A NOVEMBER 5, 2008 LETTER, CHRYSLER SUBMITTED A DEFECT INFORMATION REPORT DESCRIBING A DEFECT CONDITION THAT COULD RESULT IN PRNDL MISALIGNMENT (I.E., INCORRECT GEAR INDICATION) IN APPROXIMATELY 20,300 MODEL YEAR (MY) 2006 THROUGH 2009 DODGE CHARGER AND MAGNUM POLICE VEHICLES BUILT FROM MAY 17, 2005 THROUGH OCTOBER 21, 2008 (NHTSA RECALL NO. 08V-583, CHRYSLER RECALL H37).ACCORDING TO CHRYSLER, THE GEARSHIFT CABLE MAY BECOME DISENGAGED FROM THE STEERING COLUMN MOUNTING BRACKET AND CAUSE AN INCORRECT TRANSMISSION GEARSHIFT POSITION DISPLAY.THIS COULD ALLOW THE VEHICLE TO MOVE INADVERTENTLY AND CAUSE A CRASH WITHOUT WARNING.CHRYSLER DEALERS WILL REMEDY THE DEFECT CONDITION BY INSTALLING A REDUNDANT LOCKING MECHANISM TO THE GEARSHIFT CABLE AND THE MOUNTING BRACKET TO ENSURE PROPER RETENTION AND SHIFT LINKAGE FUNCTION. CHRYSLER USES A UNIQUE COLUMN SHIFTER IN THESE POLICE VEHICLES.AFTER PE08-052 WAS OPENED, CHRYSLER INSPECTED A MY 2009 POLICE VEHICLE AND NOTED THAT THOUGH THE GEARSHIFT CABLE APPEARED FULLY SEATED INTO THE STEERING COLUMN MOUNTING BRACKET, THE CABLE RETENTION FEATURE (LOCKING PIN) WAS NOT FULLY SEATED.CHRYSLER SUBSEQUENTLY DETERMINED THAT IF THE RETENTION FEATURE IS NOT FULLY SEATED, THE CABLE MAY DISENGAGE FROM THE MOUNTING BRACKET, RESULTING IN THE SHIFT LINKAGE SYSTEM NOT FUNCTIONING TO DESIGN INTENT WITH THE POTENTIAL FOR INCORRECT GEAR POSITION INDICATION VIA THE PRNDL DISPLAY.CHYSLER'S INSPECTION OF 59 MY 2009 DODGE CHARGER AND MAGNUM POLICE VEHICLES IN SEPTEMBER AND OCTOBER FOUND 30 WHERE THE GEARSHIFT CABLE WAS NOT FULLY ENGAGED TO THE MOUNTING BRACKET.THERE ARE NO REPORTED CRASHES OR INJURIES RELATED TO THE DEFECT CONDITION TO DATE. THIS INVESTIGATION IS CLOSED.