← New search

2008 Dodge Charger

Owner reports · Recalls · Investigations

Limited comparison data

There is not enough comparable history to draw a useful model-year comparison.

About this comparison →

When problems were reported

Mileage at the reported incident

393 reports with mileage · 216 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 391 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Air Bags. Review the 124 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 89 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

24 crash reports22 fire reports17 injury reports

Steering complaints

30 reports
Clear category filter
Mileage unknown · Jun 17, 2013
Electrical SystemEngineSteering

IGNITION MODULATOR SWITCH SHUT THE CAR COMPLETLY DOWN AS THE WAS COMING TO A STOP THIS PART ATTACHES INTO THE COMPUTER AND CAN GO AT ANYTIME EVEN WHEN DRIVING. CHRYSLER HAS A MAJOR BACK ORDER ON THIS PART AND HAS NO IDEA WHEN THEY CAN GET THE PART TO THE DEALERSHIPS TO CORRECT THE ISSUE. THERE ARE OVER 1000 VEHICLES CURRENTLY WI…

Read full complaint

IGNITION MODULATOR SWITCH SHUT THE CAR COMPLETLY DOWN AS THE WAS COMING TO A STOP THIS PART ATTACHES INTO THE COMPUTER AND CAN GO AT ANYTIME EVEN WHEN DRIVING. CHRYSLER HAS A MAJOR BACK ORDER ON THIS PART AND HAS NO IDEA WHEN THEY CAN GET THE PART TO THE DEALERSHIPS TO CORRECT THE ISSUE. THERE ARE OVER 1000 VEHICLES CURRENTLY WITH ISSUE ACROSS THE USA. I HAVE CHECKED WITH DEALERSHIPS FROM NJ AS FAR AS MO AFTER THEY CHECK THE DATABASE IN THE PARTS DEPARTMENT I GET THE SAME ANSWER NO PART IN STOCK. *TR

NHTSA ODI #10520262

101,761 miles · May 15, 2013
Electrical SystemElectronic Stability Control (esc)Service Brakes, Hydraulic

1 SOLUTION 2008 DODGE CHARGER THE ESP/BAS LIGHT COMES ON WHEN I MAKE A LEFT TURN AND STAYS ON FOR A WHILE AND THE RESETS. THIS IS A RE-OCCURRING ISSUE. WAS TOLD BY DODGE THAT STEERING COLUMN MAY HAVE TO BE REPAIRED. (WAS THIS A RECALL FOR DODGE?). THE CAR SEEMS TO BE DIFFICULT TO STEER DUE TO THE CAR BEING VERY "LOOSE" AND FEELS…

Read full complaint

1 SOLUTION 2008 DODGE CHARGER THE ESP/BAS LIGHT COMES ON WHEN I MAKE A LEFT TURN AND STAYS ON FOR A WHILE AND THE RESETS. THIS IS A RE-OCCURRING ISSUE. WAS TOLD BY DODGE THAT STEERING COLUMN MAY HAVE TO BE REPAIRED. (WAS THIS A RECALL FOR DODGE?). THE CAR SEEMS TO BE DIFFICULT TO STEER DUE TO THE CAR BEING VERY "LOOSE" AND FEELS AS IF THE CAR IS NOT ALIGNED BUT RECENTLY HAD NEW ALIGNMENT DONE. ALSO, LEFT REAR DRIVER'S SIDE DOOR LOCK WILL NOT WORK. THE WINDOW WORKS FINE BUT THE DOOR LOCK HAS STOPPED FUNCTIONING. HAVE HAD ISSUES WITH ROTORS SINCE I PURCHASED THE CAR WITH ONLY 17 MILES ON IT. ROTORS REPLACED SEVERAL TIMES AND WAS EVEN TOLD THAT THE ROTORS WERE WARPED IN FACTOR INSTALLATION. *TR

NHTSA ODI #10512185

50,000 miles · May 10, 2013
Steering

TL* THE CONTACT OWNS A 2008 DODGE CHARGER. THE CONTACT STATED THAT THE STEERING COLUMN FAILED, PREVENTING THE VEHICLE FROM BEING STARTED OR BEING SHUT OFF. THE CONTACT ALSO STATED THAT THE STEERING COLUMN FAILURE WAS EXPERIENCED WITH AN ENTIRE FLEET OF DODGE CHARGERS THAT WERE BEING UTILIZED BY THE LANIER COUNTY SHERIFF'S OFFICE…

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE CHARGER. THE CONTACT STATED THAT THE STEERING COLUMN FAILED, PREVENTING THE VEHICLE FROM BEING STARTED OR BEING SHUT OFF. THE CONTACT ALSO STATED THAT THE STEERING COLUMN FAILURE WAS EXPERIENCED WITH AN ENTIRE FLEET OF DODGE CHARGERS THAT WERE BEING UTILIZED BY THE LANIER COUNTY SHERIFF'S OFFICE. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS 50,000 AND THE CURRENT MILEAGE IS 180,000.

NHTSA ODI #10511421

40,000 miles · May 8, 2013
SteeringSuspensionWheels

THE TIE ROD ENDS IN THIS CAR HAVE BEEN REPLACED TWICE AND NOW IM GOING IN FOR A THIRD TIME. MY MECHANIC EXPLAINED TO ME THAT THESE CARS ARE KNOWN FOR THEIR TIE ROD ENDS BREAKING. I FEEL IT SHOULD BE LOOKED INTO..I HAVE BEEN TO ONLINE FORUMS FOR THIS VEHICLE AND ITS MENTIONED A LOT ON THERE TOO. IF A PART IS DEFECTIVE THE MANUFAC…

Read full complaint

THE TIE ROD ENDS IN THIS CAR HAVE BEEN REPLACED TWICE AND NOW IM GOING IN FOR A THIRD TIME. MY MECHANIC EXPLAINED TO ME THAT THESE CARS ARE KNOWN FOR THEIR TIE ROD ENDS BREAKING. I FEEL IT SHOULD BE LOOKED INTO..I HAVE BEEN TO ONLINE FORUMS FOR THIS VEHICLE AND ITS MENTIONED A LOT ON THERE TOO. IF A PART IS DEFECTIVE THE MANUFACTURER SHOULD BE RECALLING THESE VEHICLES. *TR

NHTSA ODI #10511045

39,000 miles · Apr 22, 2013
Steering

TL* THE CONTACT OWNS A 2008 DODGE CHARGER. THE CONTACT STATED THAT THE STEERING WHEEL SUDDENLY BECAME HARD TO TURN. THE FAILURE WAS EXPERIENCED SEVERAL TIMES. THE STEERING RETURNED TO NORMAL FUNCTION WHEN THE ENGINE WAS RESTARTED. THE VEHICLE WAS TAKEN TO THE DEALER TO HAVE A DIAGNOSED PERFORMED. THE VEHICLE WAS NOT REPAIRED. TH…

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE CHARGER. THE CONTACT STATED THAT THE STEERING WHEEL SUDDENLY BECAME HARD TO TURN. THE FAILURE WAS EXPERIENCED SEVERAL TIMES. THE STEERING RETURNED TO NORMAL FUNCTION WHEN THE ENGINE WAS RESTARTED. THE VEHICLE WAS TAKEN TO THE DEALER TO HAVE A DIAGNOSED PERFORMED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE VIN WAS NOT AVAILABLE. THE FAILURE AND CURRENT MILEAGE WAS 39,000.

NHTSA ODI #10509077

71,120 miles · Sep 5, 2012
Steering

DRIVER HAD BEEN EXPERIENCING INTERMITTENT PROBLEMS WITH ESP BAS LIGHT COMING ON ALONG WITH OCCASIONAL POPPING SOUNDS FROM STEERING WHEEL WHEN MAKING TURNS. ON DAY OF INCIDENT, DRIVER WAS ATTEMPTING TO MAKE A (LEFT) U-TURN IN A MEDIAN. STEERING WHEEL TURNED APPROXIMATELY 3/4 OF ONE REVOLUTION AND WOULD NOT TURN ANY FURTHER TO L…

Read full complaint

DRIVER HAD BEEN EXPERIENCING INTERMITTENT PROBLEMS WITH ESP BAS LIGHT COMING ON ALONG WITH OCCASIONAL POPPING SOUNDS FROM STEERING WHEEL WHEN MAKING TURNS. ON DAY OF INCIDENT, DRIVER WAS ATTEMPTING TO MAKE A (LEFT) U-TURN IN A MEDIAN. STEERING WHEEL TURNED APPROXIMATELY 3/4 OF ONE REVOLUTION AND WOULD NOT TURN ANY FURTHER TO LEFT. DRIVER JERKED ON STEERING WHEEL A FEW TIMES WHICH 'BROKE LOOSE' LOCK AND TURN WAS ABLE TO BE COMPLETED. VEHICLE WAS DRIVEN TO ONE DODGE DEALERSHIP FOR INSPECTION AND DRIVER WAS TOLD NO PROBLEMS COULD BE FOUND. UPON LEAVING DEALERSHIP, ESP BAS LIGHT COME ON AGAIN. DRIVER TOOK VEHICLE TO A SECOND DODGE DEALERSHIP WHERE DIAGNOSTICS REVEALED A FAULTY STEERING ANGLE SENSOR. SENSOR WAS REPLACED AND NO FURTHER PROBLEMS HAVE BEEN EXPERIENCED AT THIS TIME. *TR

NHTSA ODI #10473881

44,900 miles · Jul 26, 2012
Exterior LightingSteering

I DRIVING AND MERGED ONTO ROUTE 3 GOING SOUTH; I TURNED MY RIGHT BLINKER ON SINCE THE RAMP WAS ON THE RIGHT, IT SHUT OFF WHEN I GOT ON THE EXPRESSWAY. AUTOMATICALLY THE LEFT BLINKER CAME ON, EVEN THOUGH I DID NOT TURN IT ON. WHILE DRIVING ON THE EXPRESSWAY GOING 60MPH WITH THREE KIDS IN THE CAR I HAD TO TRY TO TURN OFF THE BLINK…

Read full complaint

I DRIVING AND MERGED ONTO ROUTE 3 GOING SOUTH; I TURNED MY RIGHT BLINKER ON SINCE THE RAMP WAS ON THE RIGHT, IT SHUT OFF WHEN I GOT ON THE EXPRESSWAY. AUTOMATICALLY THE LEFT BLINKER CAME ON, EVEN THOUGH I DID NOT TURN IT ON. WHILE DRIVING ON THE EXPRESSWAY GOING 60MPH WITH THREE KIDS IN THE CAR I HAD TO TRY TO TURN OFF THE BLINKER, WHICH WOULD NOT TURN OFF. IT WAS A SCARY SITUATION SINCE THERE WAS A LOT OF TRAFFIC; SO I WAS TRYING TO WATCH THE TRAFFIC (WHICH MAY THINK I WAS MERGING LEFT) AND FIX THE ISSUE AT THE SAME TIME. REPEATEDLY THE RIGHT BLINKER CAME ON, THEN THE LEFT AGAIN. THERE WAS A LOUD CLICKING NOISE WHEN I TRIED TO FIX IT, AFTER SEVERAL TRIES THE BLINKER SHUT OFF. I GOT OFF THE EXPRESSWAY AND EVERY TURN I MADE THE SAME THING HAPPENED. I CALL AND EMAILED CHRYSLER DODGE. I WAS TOLD A SUPERVISOR WOULD RETURN MY CALL WITHIN 24 HOURS. THEY DID NOT. I REPEATEDLY EMAILED AND CALLED. IN THE INTERIM I BROUGHT MY CAR TO THE DEALERSHIP AND I RESEARCHED THE PROBLEM ONLINE AND BY SPEAKING TO MECHANICS AND SERVICE PEOPLE AT DODGE DEALERSHIPS. ACCORDING TO ALL OF THESE SOURCES THIS IS A COMMON PROBLEM WITH DODGE CHARGERS. TODAY, JULY 26TH, I FINALLY TALKED TO A SUPERVISOR AFTER CALLING DODGE ANOTHER TWO TIMES. HE ([XXX]) SAID THAT THERE IS NO RECALL ON THE PART (WHICH I FOUND OUT WAS A CLOCK SPRING FAILURE) AND THAT THEY WOULD DO NOTHING TO HELP. I ASKED IF HE WOULD ALLOW ME TO TALK TO HIS SUPERIOR AND HE SAID HE DIDN'T HAVE ONE. HE THEN SAID HE DID BUT THEY WOULD TELL ME THE SAME THING. I ASKED IF THEY WERE GOING TO AT LEAST WARN OTHER OWNERS OF THIS ISSUE AND HE SAID NO, THAT THE CASE WAS CLOSED. I TOLD HIM ABOUT THE INFORMATION I HAD GAINED BY TALKING TO MECHANICS, SERVICE PEOPLE (INCLUDING THE ONE WHO FIXED MY CAR) AND ONLINE RESEARCH. I TOLD HIM I WOULD FAX IT TO HIM. EVEN WITH ALL OF THIS INFORMATION HE TOLD ME THAT THEY WOULD NOT DO ANYTHING ABOUT THIS ISSUE. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR

NHTSA ODI #10467879

26,000 miles · Jul 7, 2011
Power TrainSteering

TL* THE CONTACT OWNS A 2008 DODGE CHARGER. WHILE DRIVING APPROXIMATELY 15 MPH, THE CONTACT NOTICED THAT THE STEERING WHEEL WAS LOOSE AND SEEMED TO WOBBLE WHILE TURNING. THE CONTACT STATED THAT THE VEHICLE FISH-TAILED AND BECAME UNCONTROLLABLE. THE CONTACT HAD TO APPLY EXCESSIVE FORCE TO THE STEERING WHEEL IN ORDER TO GAIN CONTR…

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE CHARGER. WHILE DRIVING APPROXIMATELY 15 MPH, THE CONTACT NOTICED THAT THE STEERING WHEEL WAS LOOSE AND SEEMED TO WOBBLE WHILE TURNING. THE CONTACT STATED THAT THE VEHICLE FISH-TAILED AND BECAME UNCONTROLLABLE. THE CONTACT HAD TO APPLY EXCESSIVE FORCE TO THE STEERING WHEEL IN ORDER TO GAIN CONTROL OF THE VEHICLE. THE VEHICLE WAS TAKEN TO THE DEALER FOR DIAGNOSTICS BUT THE TECHNICIANS WERE UNABLE TO DUPLICATE OR DIAGNOSE THE FAILURE. THE FAILURE PERSISTED AND THE VEHICLE WAS TAKEN TO THE DEALER NUMEROUS TIMES BUT TO NO AVAIL. ON THE FINAL ATTEMPT, THE TECHNICIANS DIAGNOSED THE FAILURE AS THE POWER TRAIN TORQUE CONVERTER NEEDING TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 26,000.

NHTSA ODI #10410837

84,000 miles · Jul 5, 2011
Electrical SystemPower TrainSteering

I HAVE A 2008 DODGE CHARGER, WHICH HAS HAD SEVERAL ELECTRICAL PROBLEMS TO OCCUR SINCE I PURCHASED THE VEHICLE IN AUG., 2008. 2 OF THE PROBLEMS COULD HAVE CAUSED SERIOUS INJURY IF I HAD WRECKED WHEN THE STERRING WHEEL LOCKED OR JUST THE OTHER DAY THE FAN BLADE MOTORS LOCKED UP AND BURSTED MY RADIAOTR. THIS VEHICLE IS TOO NEW TO…

Read full complaint

I HAVE A 2008 DODGE CHARGER, WHICH HAS HAD SEVERAL ELECTRICAL PROBLEMS TO OCCUR SINCE I PURCHASED THE VEHICLE IN AUG., 2008. 2 OF THE PROBLEMS COULD HAVE CAUSED SERIOUS INJURY IF I HAD WRECKED WHEN THE STERRING WHEEL LOCKED OR JUST THE OTHER DAY THE FAN BLADE MOTORS LOCKED UP AND BURSTED MY RADIAOTR. THIS VEHICLE IS TOO NEW TO HAVE SO MANY DEFECTS, ESPECIALL LINKING TO ELECTRICAL MATTERS THAT ARE NOT RECOGNIZED BY THE POWER-TRAIN WARRANTY, WHICH I FEEL SHOULD HAVE ALL BEEN COVERED THE THE WARRANTY. AFTER READING HTTP://WWW.DAIMLERCHRYSLERVEHICLEPROBLEMS.COM/, I WISH THIS WAS BROUGHT TO MY ATTENTION BEFORE MAKING THE DECISION ON THIS DODGE VEHICLE. THE CAR HAS SEVERAL YEARS BEFORE BEING PAID OFF, BUT I AM NOW TERRIFIED TO CONTINUE DRIVING THIS VEHICLE KNOWING ANYTHING, UNPLAINABLE CAN HAPPEN AT ANYTIME. SOMETHING NEEDS TO BE DONE ABOUT DODGE, CHRYSLER, JEEP FOR PUTTING PEOPLE'S LIVES IN DANGER. *KB

NHTSA ODI #10410473

31,000 miles · Jul 26, 2010
Steering

TL* THE CONTACT OWNS A 2008 DODGE CHARGER. WHILE HAVING A ROUTINE OIL CHANGE PERFORMED BY AN AUTHORIZED DEALER, THE CONTACT WAS INFORMED THAT HE WOULD NEED TO HAVE THE FRONT DRIVERS SIDE TIE ROD REPLACED. THE TIE ROD WAS REPLACED BY THE AUTHORIZED DEALER UNDER FACTORY WARRANTY. THE FAILURE DID NOT RECUR. THE FAILURE MILEAGE WAS …

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE CHARGER. WHILE HAVING A ROUTINE OIL CHANGE PERFORMED BY AN AUTHORIZED DEALER, THE CONTACT WAS INFORMED THAT HE WOULD NEED TO HAVE THE FRONT DRIVERS SIDE TIE ROD REPLACED. THE TIE ROD WAS REPLACED BY THE AUTHORIZED DEALER UNDER FACTORY WARRANTY. THE FAILURE DID NOT RECUR. THE FAILURE MILEAGE WAS 31,000 AND THE CURRENT MILEAGE WAS UNKNOWN.

NHTSA ODI #10345284

Official recalls

5

16V352000 · Air Bags:frontal:passenger Side:inflator Module

May 24, 2016

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Consequence & remedy

Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

15V313000 · Air Bags:frontal:driver Side:inflator Module

May 26, 2015

Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.

14V567000 · Electrical System:ignition

Sep 17, 2014

Chrysler Group LLC (Chrysler) is recalling certain model year 2008 Chrysler 300 vehicles manufactured May 31, 2007, to May 12, 2008, Dodge Magnum vehicles manufactured May 23, 2007, to May 12, 2008, Dodge Charger vehicles manufactured May 24, 2007, to May 12, 2008, Jeep Commander vehicles manufactured April 3, 2007, to May 12, 2008, and Jeep Grand Cherokee vehicles manufactured March 21, 2007, to May 12, 2008. In the affected vehicles, the ignition key (FOBIK) may not return to the "ON" position after being rotated to the "START" position, instead sticking between the two positions. Potentially, while the vehicle is being driven, the ignition may inadvertently move through the "RUN" position to the "ACCESSORY" or "OFF" ignition position, turning off the engine.

Consequence & remedy

Consequence: If the ignition stays between "START" and "ON" positions it could cause loss of certain electrical functions. If the ignition key inadvertently moves into the "OFF" or "ACCESSORY" position, the engine will turn off, which will then depower various key safety systems including but not limited to air bags, power steering, and power braking. Loss of functionality of these systems may increase the risk of crash and/or increase the risk of injury in the event of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the ignition switch and key FOBs, free of charge. The recall began August 19, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P57.

08V583000 · Power Train:automatic Transmission:lever And Linkage:column Shift

Nov 6, 2008

CHRYSLER IS RECALLING 20,283 MY 2006-2009 CHARGER AND MAGNUM VEHICLES BUILT WITH THE POLICE PACKAGE AND EQUIPPED WITH A COLUMN SHIFTER. THE GEARSHIFT CABLE MAY BECOME DISENGAGED FROM THE STEERING COLUMN MOUNTING BRACKET AND CAUSE AN INCORRECT TRANSMISSION GEARSHIFT POSITION DISPLAY.

Consequence & remedy

Consequence: THIS COULD ALLOW THE VEHICLE TO MOVE IN AN UNEXPECTED DIRECTION STARTLING THE DRIVER, AND CAUSE A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL ADD A REDUNDANT LOCKING MECHANISM TO THE GEARSHIFT CABLE AT THE MOUNTING BRACKET TO ENSURE PROPER RETENTION AND SHIFT LINKAGE FUNCTION. THE RECALL BEGAN ON NOVEMBER 10, 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

08V295000 · Power Train:axle Hubs

Jul 2, 2008

CHRYSLER IS RECALLING 5,509 MY 2008 300, DODGE MAGNUM, AND CHARGER VEHICLES. THE TORQUE RETENTION CRIMP FEATURE WAS MISSED DURING THE MANUFACTURE OF ONE LOT OF REAR AXLE HUB NUTS. THIS COULD CAUSE THE NUTS TO LOOSEN AND ALLOW THE HALFSHAFT TO DISENGAGE FROM THE WHEEL HUB.

Consequence & remedy

Consequence: THIS COULD CAUSE THE VEHICLE TO LOSE POWER AND RESULT IN A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL REPLACE THE REAR AXLE HUB NUTS. THE RECALL BEGAN ON JULY 21, 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

PE08052 · Prndl Misalignment

Opened Sep 2, 2008 · Closed Nov 10, 2008

Status: closed (inferred from source dates) · Power Train:automatic Transmission:lever And Linkage:column Shift

IN A NOVEMBER 5, 2008 LETTER, CHRYSLER SUBMITTED A DEFECT INFORMATION REPORT DESCRIBING A DEFECT CONDITION THAT COULD RESULT IN PRNDL MISALIGNMENT (I.E., INCORRECT GEAR INDICATION) IN APPROXIMATELY 20,300 MODEL YEAR (MY) 2006 THROUGH 2009 DODGE CHARGER AND MAGNUM POLICE VEHICLES BUILT FROM MAY 17, 2005 THROUGH OCTOBER 21, 2008 (NHTSA RECALL NO. 08V-583, CHRYSLER RECALL H37).ACCORDING TO CHRYSLER, THE GEARSHIFT CABLE MAY BECOME DISENGAGED FROM THE STEERING COLUMN MOUNTING BRACKET AND CAUSE AN INCORRECT TRANSMISSION GEARSHIFT POSITION DISPLAY.THIS COULD ALLOW THE VEHICLE TO MOVE INADVERTENTLY AND CAUSE A CRASH WITHOUT WARNING.CHRYSLER DEALERS WILL REMEDY THE DEFECT CONDITION BY INSTALLING A REDUNDANT LOCKING MECHANISM TO THE GEARSHIFT CABLE AND THE MOUNTING BRACKET TO ENSURE PROPER RETENTION AND SHIFT LINKAGE FUNCTION. CHRYSLER USES A UNIQUE COLUMN SHIFTER IN THESE POLICE VEHICLES.AFTER PE08-052 WAS OPENED, CHRYSLER INSPECTED A MY 2009 POLICE VEHICLE AND NOTED THAT THOUGH THE GEARSHIFT CABLE APPEARED FULLY SEATED INTO THE STEERING COLUMN MOUNTING BRACKET, THE CABLE RETENTION FEATURE (LOCKING PIN) WAS NOT FULLY SEATED.CHRYSLER SUBSEQUENTLY DETERMINED THAT IF THE RETENTION FEATURE IS NOT FULLY SEATED, THE CABLE MAY DISENGAGE FROM THE MOUNTING BRACKET, RESULTING IN THE SHIFT LINKAGE SYSTEM NOT FUNCTIONING TO DESIGN INTENT WITH THE POTENTIAL FOR INCORRECT GEAR POSITION INDICATION VIA THE PRNDL DISPLAY.CHYSLER'S INSPECTION OF 59 MY 2009 DODGE CHARGER AND MAGNUM POLICE VEHICLES IN SEPTEMBER AND OCTOBER FOUND 30 WHERE THE GEARSHIFT CABLE WAS NOT FULLY ENGAGED TO THE MOUNTING BRACKET.THERE ARE NO REPORTED CRASHES OR INJURIES RELATED TO THE DEFECT CONDITION TO DATE. THIS INVESTIGATION IS CLOSED.