IllustrationBack up camera goes out (turns gray/ fizzes out) occasionally and stays on when car is in drive
2019 Dodge Challenger
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2019 Dodge Challenger do not stand out strongly from the model-year median of 45.
About this comparison →How this year compares
Owner complaints by model year
Compare all Challenger years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
150–25K
625–50K
250–75K
175–100K
0100–150K
0150K+
24 reports with mileage · 35 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 17 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Wheels. Review the 11 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 8 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
5 crash reports3 fire reports1 injury reports
Unknown Or Other complaints
14 reportsREAR CAMERA IS DARK AND CLOUDY HARD TO SEE IMPOSSABLE AT NIGHT
THIS IS MY 2ND DODGE CHALLENGE I'VE OWNED. MY FIRST ONE WAS A 2017 R/T. THE REASON I MENTION THIS IS BECAUSE ITS THE SAME ISSUE I HAD WITH THE OTHER ONE. I KEEP UP WITH ALL THE MAINTANCE AND TAKE CARE OF MY CARS. THE PROBLEM FROM WHAT I'VE BEEN TOLD IS THE EXHAUST MANIFOLD AND THERE'S ALSO A KNOCKING SOUND COMING FROM THE ENGINE…
Read full complaint
THIS IS MY 2ND DODGE CHALLENGE I'VE OWNED. MY FIRST ONE WAS A 2017 R/T. THE REASON I MENTION THIS IS BECAUSE ITS THE SAME ISSUE I HAD WITH THE OTHER ONE. I KEEP UP WITH ALL THE MAINTANCE AND TAKE CARE OF MY CARS. THE PROBLEM FROM WHAT I'VE BEEN TOLD IS THE EXHAUST MANIFOLD AND THERE'S ALSO A KNOCKING SOUND COMING FROM THE ENGINE. ITS EXACTLY LIKE THE FIRST ONE I HAD AND TRADED IN. I COULDN'T GET IT FIXED BECAUSE ITS NOT COVERED IN THE FACTORY WARRANTY OR IN THE EXTENDED WARRANTIES I BOUGHT. SO I DON'T KNOW WHAT TO DO AND DODGE WANTS ME TO PAY HUNDREDS JUST TO LOOK AT IT WHICH I SHOULDN'T HAVE TO DO WITH A CAR THAT HAS LESS THAN 30,000 MILES ON IT AND ITS SOMETHING THAT I FEEL AND BELIEVE IS THEIR FAULT. I KNOW I'M NOT THE ONLY ONE BECAUSE EVERY MECHANIC, OIL CHANGERS I'VE GONE TOO I ASK THEM ABOUT IT AND THEY TELL ME SO MANY OF THEIR CUSTOMERS COMPLAIN ABOUT THE SAME THING. I HOPE YOU CAN HELP. THANKS
MY TIRE SUFFERED A MAJOR CRACK ON THE TRAIN TO THE SIDEWALL ON JUNE 13, 2020 I CALLED RUSSELL WESTBROOK DODGE IN VAN NUYS TO PURCHASE A TIRE SINCE THIS WAS AN EMERGENCY THEY TOLD ME I HAD TO WAIT THREE DAYS BECAUSE OF ORDERING DELAYS, SO I HAD NO OTHER CHOICE TO BUY ANOTHER TIRE AT ANOTHER TIRE SHOP THIS TIRE WAS 305 3020 THE ST…
Read full complaint
MY TIRE SUFFERED A MAJOR CRACK ON THE TRAIN TO THE SIDEWALL ON JUNE 13, 2020 I CALLED RUSSELL WESTBROOK DODGE IN VAN NUYS TO PURCHASE A TIRE SINCE THIS WAS AN EMERGENCY THEY TOLD ME I HAD TO WAIT THREE DAYS BECAUSE OF ORDERING DELAYS, SO I HAD NO OTHER CHOICE TO BUY ANOTHER TIRE AT ANOTHER TIRE SHOP THIS TIRE WAS 305 3020 THE STANDARD STOCK TIRES ARE 305 35 20. I WAS UNABLE PHYSICALLY TO TAKE MY OLD TIRE WITH ME SINCE I CAME FROM A TRIP AND MY TRUNK AND INTERIOR HAD LUGGAGE. I WENT TO RUSSELL WESTBROOK DODGE ON JUNE 19, 2020 WITH THIS CONCERN AND ASK THEM AT THE VERY LEAST TO REFILL MY TIRE WITH NITROGEN WHICH I PAID $500 FOR AND ASKED TO CHECK FOR MY TIRE PRESSURE ON ALL MY TIRES, BOTH OF THESE REQUESTS WERE DENIED I FEEL UNSAFE DRIVING THIS CAR. I ASKED THE SERVICE DIRECTOR OF RUSSELL WESTBROOK DODGE IN VAN NUYS TO WRITE A SERVICE DOCKET DETAILING MY SITUATION AND HIS DENIAL TO CHECK MY TIRE PRESSURE AND TO FILL MY TIRES WITH NITROGEN, AS WELL AS A POTENTIAL ALIGNMENT HE DECLINED ALL OF THESE REQUEST AND BANNED ME FROM SERVICING MY CAR, I FEEL VERY OVERWHELMED FOR MY SAFETY AND FOR THE SAFETY OF OTHERS BECAUSE OF THIS NEGLIGENCE BROUGHT BY RUSSELL WESTBROOK DODGE. I REACHED OUT TO PERELLI TIRES LLC AND THEY DECLINED TO HELP ME BECAUSE I WAS AN ABLE TO HAVE THE TIRE WITH ME FOR INSPECTION, IF I HAD SPACE IN MY TRUCK I WOULD'VE TAKEN MY TIRE. ON ANOTHER MATTER I CONTACTED FCA DODGE REGARDING STEERING CLICKING NOISE COMING FROM MY CAR WHEN TURNING OUR PARKING THE CAR BETWEEN ZERO AND 3 MILES PER. *TR
Official recalls
320V191000 · Back Over Prevention: Sensing System: Camera
Sep 10, 2020
Chrysler (FCA US LLC) is recalling certain 2020 Jeep Gladiator and Jeep Cherokee, 2019-2020 Ram 1500 Pickup, Ram 2500 Pickup, Ram 3500 Pickup, Chrysler Pacifica, Dodge Durango, Jeep Grand Cherokee, Jeep Wrangler, and Jeep Renegade and 2019 Dodge Challenger vehicles equipped with 8.4" or 12" radio displays. A software error can cause the rearview camera image to remain displayed after the vehicle has been shifted out of reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rearview Mirrors."
Consequence & remedy
Consequence: The lingering rearview image can distract the driver, increasing the risk of a crash.
Remedy: Chrysler has notified owners, and dealers will update the radio display software, free of charge. Optionally, owners can choose to remotely update their software via an Over-The-Air (OTA) update available as of May 1, 2020. The recall began April 27, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is W30-W37.
19V758000 · Service Brakes; Tires; Wheels
Oct 24, 2019
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger vehicles. An incompatible front wheel and brake package was installed and may allow the front tire to contact the steering knuckle, causing tire damage.
Consequence & remedy
Consequence: A damaged tire can suddenly lose air pressure and increase the risk of a crash.
Remedy: FCA US will notify owners, and dealers will replace the front wheels and inspect and replace the front tires, as necessary. In addition, dealers will inspect the wheel alignment, adjusting it if necessary. These repairs will be performed free of charge. The recall began December 19, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA's number for this recall is VB0.
Additional source detail variants (3)
Service Brakes
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger vehicles. An incompatible front wheel and brake package was installed and may allow the front tire to contact the steering knuckle, causing tire damage.
Consequence: A damaged tire can suddenly lose air pressure and increase the risk of a crash.
Remedy: FCA US will notify owners, and dealers will replace the front wheels and inspect and replace the front tires, as necessary. In addition, dealers will inspect the wheel alignment, adjusting it if necessary. These repairs will be performed free of charge. The recall began December 19, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA's number for this recall is VB0.
Wheels
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger vehicles. An incompatible front wheel and brake package was installed and may allow the front tire to contact the steering knuckle, causing tire damage.
Consequence: A damaged tire can suddenly lose air pressure and increase the risk of a crash.
Remedy: FCA US will notify owners, and dealers will replace the front wheels and inspect and replace the front tires, as necessary. In addition, dealers will inspect the wheel alignment, adjusting it if necessary. These repairs will be performed free of charge. The recall began December 19, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA's number for this recall is VB0.
Tires
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger vehicles. An incompatible front wheel and brake package was installed and may allow the front tire to contact the steering knuckle, causing tire damage.
Consequence: A damaged tire can suddenly lose air pressure and increase the risk of a crash.
Remedy: FCA US will notify owners, and dealers will replace the front wheels and inspect and replace the front tires, as necessary. In addition, dealers will inspect the wheel alignment, adjusting it if necessary. These repairs will be performed free of charge. The recall began December 19, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA's number for this recall is VB0.
19V203000 · Electrical System: Instrument Cluster/panel
Mar 14, 2019
Chrysler (FCA US LLC) is recalling certain 2019 Dodge Challenger and Charger and Chrysler 300 vehicles. The instrument cluster may not properly illuminate driver warnings. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 101, "Control and Displays."
Consequence & remedy
Consequence: Failure of the instrument cluster to properly illuminate may prevent the driver from receiving warnings about the vehicle's systems, increasing the risk of crash.
Remedy: Chrysler has notified owners, and dealers will update the instrument cluster software, free of charge. The recall began April 8, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V32.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.