IllustrationDriveshaft carrier bearing out at 28,000 miles of use. Common problem. Needs a recall.
2017 Dodge Challenger
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2017 Dodge Challenger do not stand out strongly from the model-year median of 45.
About this comparison →How this year compares
Owner complaints by model year
Compare all Challenger years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
80–25K
1025–50K
350–75K
075–100K
0100–150K
1150K+
22 reports with mileage · 27 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 16 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Suspension. Review the 6 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 5 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
7 crash reports2 fire reports5 injury reports
Power Train complaints
5 reportsDRIVE SHAFT VIBRATION AT 46,600 MILES. NEEDS REPLACING BY DEALER. OUT OF WARRANTY. $1400.00
I WANTED TO REPORT THAT I WAS INJURED ON 10/6/2020. WHEN MY 2017 V6 CHALLENGER WENT OUT OF GEAR FROM "PARK" AND DRUG ME DOWN, AS IT ROLLED BACKWARDS (WHILE IN "PARK"). I SUSTAINED MULTIPLE INJURIES ALL OVER MY BODY. I WENT TO THE E.R. AND FOLLOWED UP WITH PRIMARY DOCTOR. I ALSO HAVE AN APPOINTMENT WITH AN ORTHOPEDIST. I AM WRITI…
Read full complaint
I WANTED TO REPORT THAT I WAS INJURED ON 10/6/2020. WHEN MY 2017 V6 CHALLENGER WENT OUT OF GEAR FROM "PARK" AND DRUG ME DOWN, AS IT ROLLED BACKWARDS (WHILE IN "PARK"). I SUSTAINED MULTIPLE INJURIES ALL OVER MY BODY. I WENT TO THE E.R. AND FOLLOWED UP WITH PRIMARY DOCTOR. I ALSO HAVE AN APPOINTMENT WITH AN ORTHOPEDIST. I AM WRITING TO URGE YOU TO PLEASE RECALL AND FIX THE 2017 V6 CHALLENGERS FOR PEOPLES SAFETY. I DON'T WANT WHAT HAPPENED TO ME TO HAPPEN TO ANYONE ELSE. THANK YOU VERY MUCH FOR TAKING CARE OF THIS ISSUE.*DT*DT*DT THE CONSUMER PROVIDED PHOTOS. *TR*DT*DT
IN NOVEMBER AND DECEMBER OF 2017 AND AGAIN IN JANUARY 2018 AND SERIES OF POWER-TRAIN GEAR CHANGING WHILE DRIVING OCCURRED WHILE ON INTERSTATE I-20 AND 285 AND 85 AND GENERALLY AROUND TOWN WHICH CAUSED TO HAVE TO PULL OVER AND CALL A TOW TRUCK OR PARK UNTIL THE ISSUE WOULD STOP. THE VEHICLES WAS TAKEN TO DON JACKSON AND LANDMARK …
Read full complaint
IN NOVEMBER AND DECEMBER OF 2017 AND AGAIN IN JANUARY 2018 AND SERIES OF POWER-TRAIN GEAR CHANGING WHILE DRIVING OCCURRED WHILE ON INTERSTATE I-20 AND 285 AND 85 AND GENERALLY AROUND TOWN WHICH CAUSED TO HAVE TO PULL OVER AND CALL A TOW TRUCK OR PARK UNTIL THE ISSUE WOULD STOP. THE VEHICLES WAS TAKEN TO DON JACKSON AND LANDMARK AND LIITHIA SPRINGS CHRYSLER JEEP AND NO ONE TO THIS POINT HAS REPAIRED IT. THIS CONTINUES TO CAUSE ME TO HAVE TO PULL OVER ON THE SIDE OF THE ROAD BECOMES THE CAR BEGINS TO CHANGE GEARS WITH NO REASON AT ALL AT HIGH SPEEDS. ON 4-27-19 DON JACKSON CHRYSLER PERFORMED A RECALL AND WORK ON THE COMPUTER AND SINCE THEN MY CAR CRUISE CONTROL COMES ON AND GOES OFF WHEN EVER WNATS TO AS WELL THE RADIO AND DASH DISPLAY FLICKERS. THE CRUISE CONTROL IS ALARMING BECAUSE I AM DRIVING AT LOW SPEEDS ON THE ROADS AND CAR SUDDENLY SPEEDS UP WITH OUT MY DEPRESSING THE OR INCREASING THE GAS PEDAL. I TOOK THE VEHICLE BACK TO THE DEALER AND THEY TOLD ME I COULD NOT SEE THE TECHNICIAN UNTIL MAY 10, 2019. THIS MATTER ALL TOGETHER POINTS TO A LIFE SAFETY ISSUE AND I WOULD ASK AND HOPE YOUR ORGANIZATION COULD SEND A ENGINEER AND ACCESS THIS VEHICLE. THE DEALS HAVE SAID TO ME WHILE THE CAR THE WAS NEW THAT THEY WOULD NOT PROVIDE A LOANER OF GO TO ANY EXPENSE TO SOLVE THE ISSUES. PLEASE ADVISE
WHEN THE VEHICLE IS STARTED FOR THE DAY OR WHEN SITTING FOR 8 PLUS HOURS THE FIRST FEW SHIFTS ARE DELAYED. LEAVING FROM HOME IS NOT AS BIG OF A DEAL, AS WHEN I LEAVE FROM WORK. MY OFFICE EXIT CROSSES A 3 LANE ROAD WITH TRAFFIC SPEED LIMIT OF 45 MPH. EXPECTING THE VEHICLE TO MOVE WITHOUT DELAY TRYING TO CROSS TRAFFIC IS DANGEROUS…
Read full complaint
WHEN THE VEHICLE IS STARTED FOR THE DAY OR WHEN SITTING FOR 8 PLUS HOURS THE FIRST FEW SHIFTS ARE DELAYED. LEAVING FROM HOME IS NOT AS BIG OF A DEAL, AS WHEN I LEAVE FROM WORK. MY OFFICE EXIT CROSSES A 3 LANE ROAD WITH TRAFFIC SPEED LIMIT OF 45 MPH. EXPECTING THE VEHICLE TO MOVE WITHOUT DELAY TRYING TO CROSS TRAFFIC IS DANGEROUS AND I WAS ALMOST HIT BY CROSS TRAFFIC BECAUSE OF THE DELAY. DEALER HAS CHECKED TRANSMISSION AND STATES EVERYTHING IS NORMAL.
Official recalls
318V332000 · Electrical System:software; Electrical System:wiring; Vehicle Speed Control:cruise Control
May 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence & remedy
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Additional source detail variants (3)
Electrical System:software
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Vehicle Speed Control:cruise Control
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Electrical System:wiring
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
17V496000 · Engine And Engine Cooling:engine
Aug 8, 2017
Chrysler (FCA US LLC) is recalling certain 2017 Dodge Challenger and Charger vehicles equipped with Hellcat engines. The engine oil cooler (EOC) hoses may fail resulting in a rapid loss of engine oil.
Consequence & remedy
Consequence: If an EOC line fails, oil may spray onto the windshield or contact a hot surface, impairing driver visibility and increasing the risk of a crash or fire.
Remedy: Chrysler will notify owners, and dealers will replace the EOC lines, free of charge. The recall began October 3, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T48.
17V431000 · Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Jul 7, 2017
Chrysler (FCA US LLC) is recalling certain 2017 Dodge Challenger vehicles equipped with 5.7L V8 engines and eight-speed automatic transmissions. The transmission may not remain in the PARK position if that gear is selected, the engine is still running, and the driver exits the vehicle exited.
Consequence & remedy
Consequence: If the vehicle is exited without the transmission remaining in the PARK position and without the parking brake set, the vehicle may roll, increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will update the transmission control module software, free of charge. The recall began 28, 2017. Owners may the Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T41.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.