IllustrationTL* THE CONTACT OWNS A 2007 DODGE CALIBER. AFTER THE VEHICLE WAS TAKEN TO HAVE A FRONT WHEEL ALIGNMENT, THE TECHNICIAN INFORMED THAT THE FRAME OF THE VEHICLE WAS RUSTED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 170,000.
2007 Dodge Caliber
Owner reports · Recalls · Investigations
More warning signs than most Caliber years
Owner complaints for the 2007 Dodge Caliber are substantially higher than the model-year median of 165.
About this comparison →How this year compares
Owner complaints by model year
Compare all Caliber years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
820–25K
9925–50K
14450–75K
14575–100K
192100–150K
85150K+
747 reports with mileage · 137 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Suspension. Review the 255 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 197 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 158 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
54 crash reports18 fire reports28 injury reports
What owners actually said
884 reportsI BOUGHT MY CAR IN FEBRUARY OF 2013. APPROXIMATELY 6 MONTHS LATER I HAD TO REPLACE THE STRUTS AND BALL JOINTS ON THE CAR. THEN HAD THEM REPLACED AGAIN. 09/29/14 AND WAS TOLD AGAIN BY THE REPAIR SHOP LAST WEEK WHEN I BROUGHT THE CAR IN FOR A TUNEUP BECAUSE IT WAS HESITATING WHEN YOU STARTED TO ACCELERATE THAT I'M GOING TO NEED TO…
Read full complaint
I BOUGHT MY CAR IN FEBRUARY OF 2013. APPROXIMATELY 6 MONTHS LATER I HAD TO REPLACE THE STRUTS AND BALL JOINTS ON THE CAR. THEN HAD THEM REPLACED AGAIN. 09/29/14 AND WAS TOLD AGAIN BY THE REPAIR SHOP LAST WEEK WHEN I BROUGHT THE CAR IN FOR A TUNEUP BECAUSE IT WAS HESITATING WHEN YOU STARTED TO ACCELERATE THAT I'M GOING TO NEED TO HAVE THE STRUTS REPLACED AGAIN. SO NOW THAT'S 3 TIMES IN A LITTLE MORE 3 YRS I HAVE OWNED THE CAR. THIS CAN'T BE NORMAL. I LOOKED ONLINE AND THERE HAVE BEEN 100'S OF PEOPLE COMPLAINING ABOUT FRONT SUSPENSIONS ON THEIR CALIBERS. SO I THINK IT'S A DESIGN FAULT THAT NEEDS TO BE CORRECTED. THE ONE TIME ( THE 2ND REPAIR) I WAS TOLD THAT IT WAS A GOOD THING I BROUGHT THE CAR IN WHEN I DID OR I COULD HAVE BEEN IN A SERIOUS ACCIDENT BECAUSE THE STRUTS WERE SO BADLY DAMAGED.
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT WHILE ATTEMPTING TO POWER OFF THE VEHICLE, THE KEY WOULD NOT DISENGAGE FROM THE IGNITION. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 138,129. ....UPDATED 08/29/15 *BF UPDATED 08/26/15.*…
Read full complaint
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT WHILE ATTEMPTING TO POWER OFF THE VEHICLE, THE KEY WOULD NOT DISENGAGE FROM THE IGNITION. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 138,129. ....UPDATED 08/29/15 *BF UPDATED 08/26/15.*JB
WE WENT TO GET A FRONT END ALIGNMENT DONE BUT WAS TOLD THE DRIVERS SIDE TIEROD HAD TO BE REPLACED THEN FOUND OUT THAT THE CROSS MEMBER IS RUSTED OUT.WE JUST BOUGHT THIS CAR IN 2013 AND ITS NOT EVEN PAID OFF YET.WHAT CAN I DO ABOUT THIS CUZ IT WAS LIKE THIS WHEN WE BOUGHT IT BUT GOT WORSE!
DRIVING ON THE HIGHWAY AT 70 MPH AND CAR TRANSMISSION TEMPERATURE LIGHT CAME ON AND THE POWER TO THE CAR DECLINED TO A COAST AND I HAD TO TRY AND PULL TO THE SHOULDER IN HEAVY TRAFFIC WITH SNOW ON THE ROAD WHICH ALMOST CAUSED ME TO GET HIT BY OTHER VEHICLES GOING THE SPEED OF 70 MPH. THIS HAS HAPPENED NUMEROUS TIMES I HAVE TAKEN…
Read full complaint
DRIVING ON THE HIGHWAY AT 70 MPH AND CAR TRANSMISSION TEMPERATURE LIGHT CAME ON AND THE POWER TO THE CAR DECLINED TO A COAST AND I HAD TO TRY AND PULL TO THE SHOULDER IN HEAVY TRAFFIC WITH SNOW ON THE ROAD WHICH ALMOST CAUSED ME TO GET HIT BY OTHER VEHICLES GOING THE SPEED OF 70 MPH. THIS HAS HAPPENED NUMEROUS TIMES I HAVE TAKEN IT IN TO THE DEALER WHOM RECOMMENDED THAT I HAVE THE TRANSMISSION SERVICE DONE BY THE DEALER WHICH I PAID FOR AND COMPLIED TO HAVE PERFORMED. IT CONTINUED TO HAPPEN AND STILL LOOSES POWER GOING HIGHWAY SPEED OF 65. I HAVE TAKEN IT TO THE DEALER OVER AND OVER AND THEY DENY ANY LIABILITY AND SAY EVERYTHING IS OK. I HAVE THE LIFETIME POWERTRAIN WARRANTY ON THE VEHICLE. I AM GOING TO END UP DEAD THANKS TO A FAULTY TRANSMISSION IN THE CAR. IT HAS NEVER TOWED ANYTHING SO NO STRESS IS EVER APPLIED TO THE TRANSMISSION. NOW I AM PISSED BECAUSE MY WIFE WAS ALMOST HIT WHEN SHE WAS DRIVING IT ON THE HIGHWAY DURING RUSH HOUR AND IT REDUCED POWER ON HER. I HAVE PAPERWORK SHOWING THE DEALER CHECKING IT AND SAYING IT IS OK NOT TO MENTION THE NUMEROUS TIMES I HAVE GONE IN AND THEY SAY THEY HAVE HEARD NOTHING REGARDING PROBLEMS WITH THE CALIBER. IF YOU LOOK ON LINE THERE ARE PLENTY OF US CITIZENS THAT ARE PLAQUED WITH THIS SAME PROBLEM.......UPDATED 12/03/15 *BF UPDATED 11/13/2017*CN
AT 132000 MILES, I AM REPLACING BOTH CONTROL ARMS FOR THE FOURTH TIME ON MY 2007 DODGE CALIBER SXT 2.0L, NO TO MENTION THE NUMEROUS CV BOOTS AND BALL JOINTS. WITH THE NUMEROUS COMPLAINTS I HAVE SEEN ONLINE, IT IS SURPRISING THAT NO RECALL EFFORTS (AT LEAST SEEMINGLY) HAVE BEEN MADE FOR SUCH A DANGEROUS AND COSTLY DEFECT. I IMPLO…
Read full complaint
AT 132000 MILES, I AM REPLACING BOTH CONTROL ARMS FOR THE FOURTH TIME ON MY 2007 DODGE CALIBER SXT 2.0L, NO TO MENTION THE NUMEROUS CV BOOTS AND BALL JOINTS. WITH THE NUMEROUS COMPLAINTS I HAVE SEEN ONLINE, IT IS SURPRISING THAT NO RECALL EFFORTS (AT LEAST SEEMINGLY) HAVE BEEN MADE FOR SUCH A DANGEROUS AND COSTLY DEFECT. I IMPLORE YOUR COMPANY, PLEASE INVESTIGATE THE CONCERNS AND HAVING CHRYSLER-DODGE FIX THEIR ERRORS!!! EVEN MY MECHANIC INFORMED ME THAT THE LENGTH OF THE ARM IS JUST SHORT ENOUGH TO CREATE CONTINUAL ISSUES. THIS ISN'T RIGHT. AS A RESULT OF SO MANY REPAIRS ON THIS VEHICLE, I WILL NEVER OWN A CHRYSLER-DODGE PRODUCT AGAIN. THANK YOU FOR YOUR TIME AND CONSIDERATION. *TR
P2004 DODGE P2004 DODGE - INTAKE MANIFOLD RUNNER CONTROL STUCK OPEN READ MORE: HTTP://ENGINE-CODES.COM/P2004_DODGE.HTML#IXZZ3FRAOSEKS
WAS DRIVING HOME ONE NIGHT AND MY CAR STARED LOSING POWER AT LOWER SPEEDS. AFTER GETTING OFF THE INTERSTATE AND TURNING LEFT FROM A COMPLETE STOP MY CAR DIED. THIS STOP, GO, DIE CYCLE CONTINUED ALL THE WAY HOME NEXT MORNING GET READY TO GO TO WORK AND NOTHING. TURNED OUT THE FLUE PUMP AND WIRE HARNESS HAD MELTED AND BURNT UP.…
Read full complaint
WAS DRIVING HOME ONE NIGHT AND MY CAR STARED LOSING POWER AT LOWER SPEEDS. AFTER GETTING OFF THE INTERSTATE AND TURNING LEFT FROM A COMPLETE STOP MY CAR DIED. THIS STOP, GO, DIE CYCLE CONTINUED ALL THE WAY HOME NEXT MORNING GET READY TO GO TO WORK AND NOTHING. TURNED OUT THE FLUE PUMP AND WIRE HARNESS HAD MELTED AND BURNT UP. LUKY WE DIDN'T BURN UP TOO. WITH I COULD UPLOAD PICTURES HERE.
ONE DAY WAS DRIVING ON THE HIGHWAY AND NOTICE WHEN I WAS SWITCHING INTO THE LEFT LANE THAT MY FRONT LEFT TURNING LIGHT WAS OUT BUT THE THE SIGNAL ON THE DASHBOARD WAS BLINKING . I GOT HOME PUT THE CAR IN PARK THEN CHABGE THE BULB THEN TESTED THE BULB TO SEE WOULD IT WORK IT DIDN'T WORK SO I TOOK THE CAR TO THE MECHANIC TO HAVE I…
Read full complaint
ONE DAY WAS DRIVING ON THE HIGHWAY AND NOTICE WHEN I WAS SWITCHING INTO THE LEFT LANE THAT MY FRONT LEFT TURNING LIGHT WAS OUT BUT THE THE SIGNAL ON THE DASHBOARD WAS BLINKING . I GOT HOME PUT THE CAR IN PARK THEN CHABGE THE BULB THEN TESTED THE BULB TO SEE WOULD IT WORK IT DIDN'T WORK SO I TOOK THE CAR TO THE MECHANIC TO HAVE IT CHECKED OUT HE COULDN'T FIND OUT WHAT WAS THE ISSUE. HE THOUGHT IT WAS THE BULB TOO BUT HE FOUND OUT IT WASN'T THE BULB BECAUSE WHEN WE TURN THE HEADLIGHTS ON THE TURNING SIGNAL LIGHT WOULD BE ON BUT WHEN YOU ENGAGE THE SIGNAL IT WOULD NOT BLINK OR WHEN YOU ENGAGE THE HAZARD LIGHTS TOO IT WOULD NOT BLINK .
I WAS TRAVELING ON I-40 WHEN I HIT A BUMP IN THE ROAD, MY ENGINE LIGHT CAME ON AND STAYED ON FROM MEMPHIS, TN TO JAMESTOWN, TN. I WAS NOT HAVING ANY DRIVING PROBLEMS, THE CAR DROVE FINE. I TOOK IT IN TO ADVANCE AUTO AND HAD THEM RUN THE OBD2 ON IT. IT PULLED 4 CODES AND THEY ARE AS FOLLOWS... P2006 INTAKE MANIFOLD RUNNER-…
Read full complaint
I WAS TRAVELING ON I-40 WHEN I HIT A BUMP IN THE ROAD, MY ENGINE LIGHT CAME ON AND STAYED ON FROM MEMPHIS, TN TO JAMESTOWN, TN. I WAS NOT HAVING ANY DRIVING PROBLEMS, THE CAR DROVE FINE. I TOOK IT IN TO ADVANCE AUTO AND HAD THEM RUN THE OBD2 ON IT. IT PULLED 4 CODES AND THEY ARE AS FOLLOWS... P2006 INTAKE MANIFOLD RUNNER- STUCK CLOSED. I ALREADY CHANGED THAT PART ON 6/6/15 P1607 POWERTRAIN CONTROL MODULE - INTERNAL SHUTDOWN. P0722 OUTPUT SHAFT SPEED SENSOR P0717 TURBINE INPUT SHAFT SPEED SENSOR NOW AS I SAID, MY CAR SEEMS TO RUN FINE AND I HAVE NO IDEA WHY THESE SENSORS ARE SHOWING UP. WHAT CAN I DO TO RESET THE CODES, I ALREADY DISCONNECTED THE BATTERY AND LEFT IT OVER NIGHT BUT ENGINE LIGHT IS STILL ON. WHAT CAN I DO? THANK YOU [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).' *JB
Official recalls
417V824000 · Equipment
Dec 21, 2017
Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17V824-0103.pdf. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: If the fire extinguisher does not function properly, it can increase the risk of injury in the event of a fire.
Remedy: Chrysler will notify owners instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began February 14, 2018. Owners may contact Chrysler customer service at 1-800-853-1403 or Kidde customer service service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. Chrysler's number for this recall is T82.
10V234000 · Vehicle Speed Control:accelerator Pedal
Jun 3, 2010
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2007 DODGE CALIBER AND JEEP COMPASS PASSENGER VEHICLES MANUFACTURED FROM MARCH 7 THROUGH MAY 19, 2006. THE PIVOT BUSHINGS IN VEHICLES WITH OVERSIZED ACCELERATOR PEDAL BEARING POCKETS MAY BECOME DISLODGED AND POTENTIALLY CAUSE THE ACCELERATOR PEDAL TO BIND OR STICK.
Consequence & remedy
Consequence: SHOULD THE PEDAL BIND OR BECOME STUCK, IT CAN BE OVERCOME BY SMART BRAKES WHICH OVERRIDE THE ACCELERATOR PEDAL IN CERTAIN CONDITIONS.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL INSPECT AND REPLACE ALL AFFECTED ACCELERATOR PEDAL ASSEMBLIES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 29, 2010. OWNERS MAY CONTACT CHRYSLER TOLL-FREE AT 1-800-853-1403.
07V196000 · Wheels:hub
May 7, 2007
CERTAIN PASSENGER VEHICLES EQUIPPED WITH REAR DISC BRAKES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 135, "LIGHT VEHICLE BRAKE SYSTEMS." THE LENGTH OF THE REAR WHEEL HUB MOUNTING BOLTS MAY PREVENT ACTUATION OF THE PARK BRAKE.
Consequence & remedy
Consequence: THIS COULD ALLOW UNINTENDED MOVEMENT OF THE VEHICLE UNDER CERTAIN CONDITIONS AND CAUSE A CRASH WITHOUT WARNING.
Remedy: DEALERS WILL REPLACE THE REAR WHEEL HUB MOUNTING BOLTS AND REPAIR THE PARK BRAKE FREE OF CHARGE. THE RECALL BEGAN ON MAY 8, 2007. OWNERS MAY CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
06V493000 · Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
Dec 29, 2006
ON CERTAIN VEHICLES, THE ANTILOCK BRAKE SYSTEM (ABS) CONTROL MODULE SOFTWARE MAY CAUSE THE REAR BRAKES TO LOCK UP DURING CERTAIN BRAKING CONDITIONS.
Consequence & remedy
Consequence: THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND CAUSE A CRASH WITHOUT WARNING.
Remedy: DEALERS WILL REPROGRAM THE ABS ELECTRONIC CONTROL UNIT. THE RECALL BEGAN ON FEBRUARY 19, 2007. OWNERS MAY CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10012 · Sticking Accelerator Pedal
Opened Apr 29, 2010 · Closed Aug 26, 2010
Status: closed (inferred from source dates) · Vehicle Speed Control:accelerator Pedal
In their Defect Information Report (DIR) of June 3, 2010, Chrysler Group, LLC (Chrysler) notified NHTSA that it will conduct a safety recall of approximately 25,265 model year 2007 Dodge Caliber vehicles and 71 model year 2007 Jeep Compass vehicles manufactured from March 7, 2006 through May 19, 2006.The recall will remedy a defect in the accelerator pedal assembly (accelerator pedal) of the Electronic Throttle Control (ETC) system that can cause the accelerator pedal to stick in an open position and not return to the idle position when released.As stated in the opening resume, the subject vehicles (Caliber) are equipped with an ETC accelerator pedal manufactured by the CTS Corporation, the same supplier of the ETC accelerator pedal used in the recently recalled Toyota vehicles.The ETC accelerator pedal used in Caliber and Compass vehicles is not the same as those used in the recalled Toyota vehicles.They are of a different design, were manufactured using different tooling, and fail in a different manner.According to Chrysler and CTS, oversized bearing pockets in the ETC accelerator pedal housing of the Caliber and Compass vehicles allows the accelerator pedal pivot shaft bearings to dislodge from the housing.If this occurs, the accelerator pedal can stick in an open position (i.e., fails to return to the closed position) or be slow to return.Chrysler's DIR notes that the subject vehicles are equipped with Smart Brake Technology and contends that the impact of a binding or sticking accelerator pedal can be negated by its Smart Brake system.In Chrysler's view, the system enables the brake pedal input to override the throttle control system and safely depower the vehicle and minimizes the potential for safety consequences resulting from the defect in the accelerator pedal.Further, Chrysler states, as a result of the presence of this technology, Chrysler Group LLC has concluded that the condition described in this report does not present an unreasonable risk to motor vehicle safety.ODI does not concur with Chrysler's position that the Smart Brake technology employed in the subject vehicles eliminates unreasonable risks to safety stemming from the ETC accelerator pedal defect.Aside from the fact that the technology is applicable only to situations where the brake pedal is activated, the Smart Brake system implemented in the subject vehicles will override a stuck throttle under a discrete set of conditions.Because driver behaviors (e.g., kicking at the accelerator pedal to dislodge it, or pumping the brake pedal instead of steady application) may delay or prevent activation of the Smart Brake system in the subject vehicles, ODI believes that this Smart Brake system does not totally eliminate unreasonable risks to safety posed by this defect or the necessity of a safety recall in this case.See Safety Recall file 10V-234 for recall details.