NHTSA owner reports · September 18, 2026 snapshot.
Suspension complaints
255 reportsClear category filter140,000 miles · Dec 22, 2015
Electrical SystemService BrakesStructure
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. WHILE DRIVING 45 MPH, THE CONTACT NOTICED THAT THE ANTI SKID AND ABS WARNING LIGHTS ILLUMINATED WITHOUT WARNING. ALL OF THE INSTRUMENT PANEL LIGHTS ALSO ILLUMINATED. THE CONTACT DROVE THE VEHICLE TO A DEALER WHERE IT WAS DIAGNOSED THAT THE FRONT AND REAR ENDS OF THE VEHICLE NEEDED TO BE…
Read full complaint
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. WHILE DRIVING 45 MPH, THE CONTACT NOTICED THAT THE ANTI SKID AND ABS WARNING LIGHTS ILLUMINATED WITHOUT WARNING. ALL OF THE INSTRUMENT PANEL LIGHTS ALSO ILLUMINATED. THE CONTACT DROVE THE VEHICLE TO A DEALER WHERE IT WAS DIAGNOSED THAT THE FRONT AND REAR ENDS OF THE VEHICLE NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE CONTACT SPOKE WITH THE MANUFACTURER WHO APPROVED THE REPAIRS PERFORMED BY ANOTHER DEALER. THE VEHICLE WAS REPAIRED, BUT THE FAILURE RECURRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 140,000. UPDATED 02/12/16*LJ *TR
NHTSA ODI #10811734
110,000 miles · Nov 11, 2015
EngineSteeringSuspension
SUB FRAME WAS SO RUSTED IT AFFECTED THE STEERING, MOTOR MOUNT COLLAPSED INTO THE SUB FRAME, LOWER CONTROL ARM WAS ALMOST SEPARATED FROM THE FRAME. I WAS TRAVELING AT ABOUT 65 MPH ON THE N.Y. THRUWAY WHEN I STARTED HAVING PROBLEMS WITH THE STEERING . WHEN I ARRIVED HOME I INVESTIGATED AND FOUND THE CAR WAS SO UNSAFE I COULDN'T D…
Read full complaint
SUB FRAME WAS SO RUSTED IT AFFECTED THE STEERING, MOTOR MOUNT COLLAPSED INTO THE SUB FRAME, LOWER CONTROL ARM WAS ALMOST SEPARATED FROM THE FRAME. I WAS TRAVELING AT ABOUT 65 MPH ON THE N.Y. THRUWAY WHEN I STARTED HAVING PROBLEMS WITH THE STEERING . WHEN I ARRIVED HOME I INVESTIGATED AND FOUND THE CAR WAS SO UNSAFE I COULDN'T DRIVE IT AGAIN UNTIL SUB FRAME WAS REPLACED. I SAVED THE FRAME THAT WAS REMOVED FROM THE VEHICLE IF NEEDED.
NHTSA ODI #10789838
76,092 miles · Nov 6, 2015
StructureSuspension
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. WHILE HAVING ROUTINE MAINTENANCE PERFORMED ON THE VEHICLE BY AN INDEPENDENT MECHANIC, IT WAS BROUGHT TO THE ATTENTION OF THE CONTACT THAT THE VEHICLE'S CROSS MEMBER HAD RUST HOLES. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE FRONT LOWER CONTROL ARMS, INNER AND OU…
Read full complaint
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. WHILE HAVING ROUTINE MAINTENANCE PERFORMED ON THE VEHICLE BY AN INDEPENDENT MECHANIC, IT WAS BROUGHT TO THE ATTENTION OF THE CONTACT THAT THE VEHICLE'S CROSS MEMBER HAD RUST HOLES. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE FRONT LOWER CONTROL ARMS, INNER AND OUTER TIE RODS, AND CROSS MEMBER FAILED AND NEEDED TO BE REPAIRED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 76,092.
NHTSA ODI #10788826
140,000 miles · Nov 2, 2015
Suspension
NOISE UNDER FRONT OF CAR, TOOK TO MY MECHANIC TOLD ME SUB FRAME WAS RUSTED THROUGH AND CRACKED. THIS NEEDED TO BE REPLACED. @140000 MILES.
NHTSA ODI #10787771
89,000 miles · Oct 16, 2015
Suspension
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. WHILE THE VEHICLE WAS BEING SERVICED, THE MECHANIC NOTICED THAT THE REAR TRAILING ARM BUSHING WAS STUCK TO THE SUSPENSION. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 89,000. THE VIN WAS NOT AVAILABLE.
NHTSA ODI #10782990
110,000 miles · Sep 29, 2015
StructureSuspension
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT WHILE AT AN INDEPENDENT MECHANIC FOR A ROUTINE SERVICE, THE MECHANIC DIAGNOSED THAT THE SUBFRAME CORRODED AND BOTH FRONT BALL JOINTS NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 110,00…
Read full complaint
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. THE CONTACT STATED THAT WHILE AT AN INDEPENDENT MECHANIC FOR A ROUTINE SERVICE, THE MECHANIC DIAGNOSED THAT THE SUBFRAME CORRODED AND BOTH FRONT BALL JOINTS NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 110,000.
NHTSA ODI #10778502
50,000 miles · Sep 26, 2015
Suspension
AT 50,00 MILES I WAS TOLD BY THE MECHANIC DURING AN OIL CHANGE THAT THE VEHICLES BALL JOINTS COULD FAIL WITHOUT WARNING. I HAD THE BALL JOINTS REPLACED AT 50,000 MILES AND THEN AGAIN AT 75,000 MILES. AT 80,000 MILES I ALSO HAVE TO REPLACE INNER AND OUTER TIE RODS, CONTROL ARM BEARINGS, AND SUSPENSION TIE BAR LINKS, AND STRUTS. …
Read full complaint
AT 50,00 MILES I WAS TOLD BY THE MECHANIC DURING AN OIL CHANGE THAT THE VEHICLES BALL JOINTS COULD FAIL WITHOUT WARNING. I HAD THE BALL JOINTS REPLACED AT 50,000 MILES AND THEN AGAIN AT 75,000 MILES. AT 80,000 MILES I ALSO HAVE TO REPLACE INNER AND OUTER TIE RODS, CONTROL ARM BEARINGS, AND SUSPENSION TIE BAR LINKS, AND STRUTS. DODGE CUSTOMER SERVICE HAS STATED THERE IS A "UNRESOLVED" ISSUE. THE SUSPENSION ISSUES COULD RESULT IN AN ACCIDENT WHEN TRAVELING AT HIGHWAY SPEEDS IF THE SUSPENSION FAILS.
NHTSA ODI #10777804
80,000 miles · Sep 12, 2015
SuspensionWheels
THE FIRST INDICATION OF THE PROBLEM WAS AS I WAS DRIVING AT HIGHER SPEEDS (ABOVE 50 MPH). I NOTICED A DEFINITE SHAKING WHICH I TOOK TO MEAN THAT THE TIRES WERE NOT BALANCED PROPERLY. I HAD THE VEHICLE CHECKED AND WAS TOLD THAT THE FRONT BALL JOINTS, CONTROL ARMS AND TIE RODS WERE WORN OUT. I REPLACED THESE PARTS AND THE TIRES AS…
Read full complaint
THE FIRST INDICATION OF THE PROBLEM WAS AS I WAS DRIVING AT HIGHER SPEEDS (ABOVE 50 MPH). I NOTICED A DEFINITE SHAKING WHICH I TOOK TO MEAN THAT THE TIRES WERE NOT BALANCED PROPERLY. I HAD THE VEHICLE CHECKED AND WAS TOLD THAT THE FRONT BALL JOINTS, CONTROL ARMS AND TIE RODS WERE WORN OUT. I REPLACED THESE PARTS AND THE TIRES AS THEY HAD BEGUN TO WEAR BADLY. I AM NOW ABOUT TO REPLACE THE SAME PARTS FOR THE FOURTH TIME! THERE ARE ALSO MAJOR PROBLEMS WITH THE REAR SUSPENSION. I AM REPLACING THE REAR CONTROL ARMS AND LATERAL LINKS FOR THE THIRD TIME! I DRIVE A LOT AND AT FIRST PUT THE PROBLEM DOWN TO THE NUMBER OF MILES I DRIVE. THE VEHICLE IS NOW AT APPROXIMATELY 211,000 MILES, BUT THIS IS RIDICULOUS! THE LAST TIME THE FRONT SUSPENSION WORE OUT, THE RIGHT FRONT WHEEL NEARLY FELL OFF! THE VEHICLE BEGAN TO SHAKE SEVERELY AND AS I WAS A MILE OR TWO TO MY DESTINATION, I SLOWED TO A CRAWL AND WHEN I ARRIVED I WAS NEARLY SICK WHEN I SAW HOW BAD IT WAS. NOW THE FRONT AND THE REAR ARE BAD AT THE SAME TIME. HELP ME OUT PLEASE! I'M AT MY WITS END AS I STILL OWE SOMEONE MONEY I HAD TO BORROW THE LAST TIME I NEEDED THIS FIXED. I REALLY DON'T WANT A CAR PAYMENT NOW AS MY WIFE LOST HER JOB RECENTLY.
NHTSA ODI #10763290
99,900 miles · Sep 2, 2015
StructureSuspension
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. WHILE DRIVING APPROXIMATELY 20 MPH, THE FRONT SUBFRAME FRACTURED DUE TO RUST. THE VEHICLE WAS TAKEN TO THE DEALER FOR DIAGNOSTIC TESTING. THE TECHNICIAN STATED THAT THE SUBFRAME AND SWAY BAR NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED. THE APPR…
Read full complaint
TL* THE CONTACT OWNS A 2007 DODGE CALIBER. WHILE DRIVING APPROXIMATELY 20 MPH, THE FRONT SUBFRAME FRACTURED DUE TO RUST. THE VEHICLE WAS TAKEN TO THE DEALER FOR DIAGNOSTIC TESTING. THE TECHNICIAN STATED THAT THE SUBFRAME AND SWAY BAR NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED. THE APPROXIMATE FAILURE MILEAGE WAS 99,900.
NHTSA ODI #10761120
121,600 miles · Aug 5, 2015
Service BrakesSteeringSuspension
BRAKES ON THIS VEHICLE ARE NO GOOD, VERY HARD TO STOP. BALL JOINTS NO GOOD STEERING ON THIS VEHICLE IS NOT SAFE EITHER I HAVE NOTICED ALL THE RECALLS AND COMPLAINTS.
NHTSA ODI #10746443
Official recalls
4Dec 21, 2017
Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17V824-0103.pdf. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: If the fire extinguisher does not function properly, it can increase the risk of injury in the event of a fire.
Remedy: Chrysler will notify owners instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began February 14, 2018. Owners may contact Chrysler customer service at 1-800-853-1403 or Kidde customer service service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. Chrysler's number for this recall is T82.
Jun 3, 2010
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2007 DODGE CALIBER AND JEEP COMPASS PASSENGER VEHICLES MANUFACTURED FROM MARCH 7 THROUGH MAY 19, 2006. THE PIVOT BUSHINGS IN VEHICLES WITH OVERSIZED ACCELERATOR PEDAL BEARING POCKETS MAY BECOME DISLODGED AND POTENTIALLY CAUSE THE ACCELERATOR PEDAL TO BIND OR STICK.
Consequence & remedy
Consequence: SHOULD THE PEDAL BIND OR BECOME STUCK, IT CAN BE OVERCOME BY SMART BRAKES WHICH OVERRIDE THE ACCELERATOR PEDAL IN CERTAIN CONDITIONS.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL INSPECT AND REPLACE ALL AFFECTED ACCELERATOR PEDAL ASSEMBLIES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 29, 2010. OWNERS MAY CONTACT CHRYSLER TOLL-FREE AT 1-800-853-1403.
May 7, 2007
CERTAIN PASSENGER VEHICLES EQUIPPED WITH REAR DISC BRAKES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 135, "LIGHT VEHICLE BRAKE SYSTEMS." THE LENGTH OF THE REAR WHEEL HUB MOUNTING BOLTS MAY PREVENT ACTUATION OF THE PARK BRAKE.
Consequence & remedy
Consequence: THIS COULD ALLOW UNINTENDED MOVEMENT OF THE VEHICLE UNDER CERTAIN CONDITIONS AND CAUSE A CRASH WITHOUT WARNING.
Remedy: DEALERS WILL REPLACE THE REAR WHEEL HUB MOUNTING BOLTS AND REPAIR THE PARK BRAKE FREE OF CHARGE. THE RECALL BEGAN ON MAY 8, 2007. OWNERS MAY CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
Dec 29, 2006
ON CERTAIN VEHICLES, THE ANTILOCK BRAKE SYSTEM (ABS) CONTROL MODULE SOFTWARE MAY CAUSE THE REAR BRAKES TO LOCK UP DURING CERTAIN BRAKING CONDITIONS.
Consequence & remedy
Consequence: THIS COULD RESULT IN A LOSS OF VEHICLE CONTROL AND CAUSE A CRASH WITHOUT WARNING.
Remedy: DEALERS WILL REPROGRAM THE ABS ELECTRONIC CONTROL UNIT. THE RECALL BEGAN ON FEBRUARY 19, 2007. OWNERS MAY CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10012 · Sticking Accelerator Pedal
Opened Apr 29, 2010 · Closed Aug 26, 2010
Status: closed (inferred from source dates) · Vehicle Speed Control:accelerator Pedal
In their Defect Information Report (DIR) of June 3, 2010, Chrysler Group, LLC (Chrysler) notified NHTSA that it will conduct a safety recall of approximately 25,265 model year 2007 Dodge Caliber vehicles and 71 model year 2007 Jeep Compass vehicles manufactured from March 7, 2006 through May 19, 2006.The recall will remedy a defect in the accelerator pedal assembly (accelerator pedal) of the Electronic Throttle Control (ETC) system that can cause the accelerator pedal to stick in an open position and not return to the idle position when released.As stated in the opening resume, the subject vehicles (Caliber) are equipped with an ETC accelerator pedal manufactured by the CTS Corporation, the same supplier of the ETC accelerator pedal used in the recently recalled Toyota vehicles.The ETC accelerator pedal used in Caliber and Compass vehicles is not the same as those used in the recalled Toyota vehicles.They are of a different design, were manufactured using different tooling, and fail in a different manner.According to Chrysler and CTS, oversized bearing pockets in the ETC accelerator pedal housing of the Caliber and Compass vehicles allows the accelerator pedal pivot shaft bearings to dislodge from the housing.If this occurs, the accelerator pedal can stick in an open position (i.e., fails to return to the closed position) or be slow to return.Chrysler's DIR notes that the subject vehicles are equipped with Smart Brake Technology and contends that the impact of a binding or sticking accelerator pedal can be negated by its Smart Brake system.In Chrysler's view, the system enables the brake pedal input to override the throttle control system and safely depower the vehicle and minimizes the potential for safety consequences resulting from the defect in the accelerator pedal.Further, Chrysler states, as a result of the presence of this technology, Chrysler Group LLC has concluded that the condition described in this report does not present an unreasonable risk to motor vehicle safety.ODI does not concur with Chrysler's position that the Smart Brake technology employed in the subject vehicles eliminates unreasonable risks to safety stemming from the ETC accelerator pedal defect.Aside from the fact that the technology is applicable only to situations where the brake pedal is activated, the Smart Brake system implemented in the subject vehicles will override a stuck throttle under a discrete set of conditions.Because driver behaviors (e.g., kicking at the accelerator pedal to dislodge it, or pumping the brake pedal instead of steady application) may delay or prevent activation of the Smart Brake system in the subject vehicles, ODI believes that this Smart Brake system does not totally eliminate unreasonable risks to safety posed by this defect or the necessity of a safety recall in this case.See Safety Recall file 10V-234 for recall details.
Illustration