← New search

2010 Chevrolet Tahoe

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2010 Chevrolet Tahoe do not stand out strongly from the model-year median of 246.

About this comparison →

How this year compares

Owner complaints by model year

Compare all Tahoe years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

All reported categories

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

201 reports with mileage · 113 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 115 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 89 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 16 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

3 crash reports0 fire reports8 injury reports

Power Train complaints

6 reports
Clear category filter
Mileage unknown · Oct 15, 2025
Power Train

We purchased a 2010 Chevrolet Tahoe from a dealership in Wisconsin in 2022. In 2023, the vehicle’s transmission failed completely at only 128,000 miles. After researching the issue, I discovered that the 6L80E transmission installed in this model year has a long history of mechanical failures, particularly involving the torque c…

Read full complaint

We purchased a 2010 Chevrolet Tahoe from a dealership in Wisconsin in 2022. In 2023, the vehicle’s transmission failed completely at only 128,000 miles. After researching the issue, I discovered that the 6L80E transmission installed in this model year has a long history of mechanical failures, particularly involving the torque converter and internal clutch packs. Numerous consumer complaints report identical failures, and GM has issued multiple service bulletins acknowledging related issues but has not initiated a recall. The repair shop diagnosed the problem as a failed torque converter and damaged internal clutch packs. There were no warning signs, one day the transmission functioned normally, and the next day it failed completely. This failure caused significant financial hardship. I paid over $5,000 for a full transmission rebuild using my credit card, resulting in ongoing interest charges and credit impact. I had to perform balance transfers to manage the debt and ease the financial burden. Given the widespread nature of this issue and GM’s acknowledgment of mechanical defects in the 6L80E transmission, I am requesting that GM reimburse repair costs and that regulators investigate the 6L80E’s reliability and safety to determine whether a recall or class action remedy is warranted.

NHTSA ODI #11693610

Mileage unknown · Dec 21, 2021
Power Train

Transmission failure knocking and pinging would not go in reverse would only go 10 mph. Vehicle has never been abused only has 128,428 miles.

NHTSA ODI #11444608

126,000 miles · Mar 2, 2021
Power TrainCrash

LIFTERS COLLAPSED, MOTOR BLEW ON THE HIGHWAY AT 60MPH CAUSING LARGE ACCIDENT ON SHOULDER

NHTSA ODI #11398640

86,000 miles · Jan 15, 2020
Electrical SystemEnginePower Train

I PURCHASED THIS VEHICLE USED IN THE FALL OF 2019 AT A USED CAR DEALERS LOT IN OREGON. IN THE SUMMER OF 2019 WE STARTED EXPERIENCING RANDOM NO START PROBLEMS. THE FIRST INCIDENCE WE THOUGHT IT WAS A FAULTY STARTER EVEN THOUGH WE COULD JUMP/SHORT IT ACROSS THE TERMINAL, AND START THE VEHICLE. AFTER REPLACING THE VEHICLES STAR…

Read full complaint

I PURCHASED THIS VEHICLE USED IN THE FALL OF 2019 AT A USED CAR DEALERS LOT IN OREGON. IN THE SUMMER OF 2019 WE STARTED EXPERIENCING RANDOM NO START PROBLEMS. THE FIRST INCIDENCE WE THOUGHT IT WAS A FAULTY STARTER EVEN THOUGH WE COULD JUMP/SHORT IT ACROSS THE TERMINAL, AND START THE VEHICLE. AFTER REPLACING THE VEHICLES STARTER WITH A REMANUFACTURED NON GM STARTER, WE STARTED HAVING MORE NO START PROBLEMS. REMEDY WAS ARCING THE STARTER POSTS ACROSS ONE ANOTHER, AND THEN VEHICLE WOULD CRANK AND START. WE HAD THE VEHICLE INSPECTED BY A GM DEALER, OUR LOCAL MECHANIC, AND THEY STATED IT HAD TO BE "DEAD" IN ORDER TO DIAGNOSE THE PROBLEM. THEN A WEEK LATER WE HAD THE CAR GO INTO "ANTI-THEFT MODE" WHILE DRIVING, AND THE SPEED AND TRANSMISSION SLOWED THE VEHICLE NEARLY TO A STOP ,- ALL THE LIGHTS STARTED BLINKING, DIC WARNING LIGHTS STARTED FLASHING CHECK STABILITY, CHECK BLIND SIDE, CHECK 4 WHEEL DR., ECT... FORTUNATELY I WAS NOT FAR FROM HOME AND PARKED THE CAR IN THE DRIVEWAY AND SHUT IT OFF. IMMEDIATELY I TRIED TO RE-START THE VEHICLE AND WE HAD A "NO-CRANK" ISSUE AGAIN. I CHECKED AND REPLACED ALL FUSES RELATING TO THE STATER EVEN THOUGH NOT BLOWN. WE THEN HAD IT TOWED TO OUR LOCAL MECHANIC WHO IS ASE CERTIFIED AND HE COMPLETELY DISMANTLED THE UNDER HOOD ELECTRONIC FUSE BLOCK, AND THE COMMUNICATION FUSE BLOCK UNDER THE DRIVERS SIDE DASH AND TO NO AVAIL- FOUND NO WIRING OR FUSE PROBLEMS. HE DIAGNOSED OVER 400 CONNECTIONS, AND COULD NOT FIND ANYTHING CONTRIBUTING TO THE PROBLEMS. HE STATED AS SOON AS HE UNBOLTED THE UNDER HOOD FUSE BLOCK THE CAR STARTED, BUT HE CONTINUED THE DIAGNOSTICS AS STATED ABOVE. THERE IS A THIRD FUSE BLOCK UNDER THE DASH THAT SITS BESIDE THE COMMUNICATION BLOCK, AND HAS FUSES THAT WERE CHECKED AS WELL. DURING JULY, AUGUST, OCTOBER 2019, WE HAD NUMEROUS NO START/CRANK INSTANCES. REMEDY IS A LARGE SCREWDRIVER AND ARCING THE STARTER.

NHTSA ODI #11299514

31,000 miles · Jun 7, 2014
Air BagsElectrical SystemPower Train

I HAVE READ THOUSANDS OF COMPLAINTS ABOUT THE DASHBOARD BEING CRACKED. MINE HAS DONE THE SAME AND I HAD TAKEN IT TO THE DEALER TO SEE IF IT WAS COVERED UNDER WARRANTY AND THEY HAD TOLD ME NO BECAUSE IT DID NOT COME FROM THE FACTORY LIKE THAT. I'M THINKING WELL NO [XXX], HAVE AN ELECTRICAL ISSUE/POWERTRAIN ISSUE/ENGINE ISSUE/ ETC…

Read full complaint

I HAVE READ THOUSANDS OF COMPLAINTS ABOUT THE DASHBOARD BEING CRACKED. MINE HAS DONE THE SAME AND I HAD TAKEN IT TO THE DEALER TO SEE IF IT WAS COVERED UNDER WARRANTY AND THEY HAD TOLD ME NO BECAUSE IT DID NOT COME FROM THE FACTORY LIKE THAT. I'M THINKING WELL NO [XXX], HAVE AN ELECTRICAL ISSUE/POWERTRAIN ISSUE/ENGINE ISSUE/ ETC IT'S PROBABLY NOT GOING TO COME FROM THE FACTORY WITH THE ISSUE. ANYWAY I AM TRYING TO CONTACT CHEVROLET TO FIX THE ISSUE AND/OR PUT OUT A RECALL FOR THE PROBLEM. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR

NHTSA ODI #10596829

36,510 miles · Oct 8, 2011
Power Train

SUPPORT BRACKET WELD TO TRANSMISSION DIPSTICK TUBE BROKE. DIPSTICK TUBE LOOSE AND ONLY HELD IN PLACE AT TRANSMISSION. CAUGHT AT A GM LUBE LOCATION IN CHARLESTON, WV DURING ROUTINE LUBE AND OIL CHANGE. THEY STATED THEY HAVE SEEN AT LEAST 6 OF THESE BREAKS IN LATE MODEL GM SUVS. IN WORST CASE TUBE COULD POP OUT OF TRANSMISSION AND…

Read full complaint

SUPPORT BRACKET WELD TO TRANSMISSION DIPSTICK TUBE BROKE. DIPSTICK TUBE LOOSE AND ONLY HELD IN PLACE AT TRANSMISSION. CAUGHT AT A GM LUBE LOCATION IN CHARLESTON, WV DURING ROUTINE LUBE AND OIL CHANGE. THEY STATED THEY HAVE SEEN AT LEAST 6 OF THESE BREAKS IN LATE MODEL GM SUVS. IN WORST CASE TUBE COULD POP OUT OF TRANSMISSION AND LEAKING TRANSMISSION OIL COULD HIT EXHAUST AND CAUSE A FIRE. MY FIX IS A SMALL HOSE CLAMP AROUND THE BRACKET AND TUBE TO HOLD IT IN PLACE. *TR

NHTSA ODI #10429185

Official recalls

3

21V050000 · Air Bags:frontal:passenger Side:inflator Module

Feb 5, 2021

General Motors, LLC (GM) is recalling certain 2007-2011 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL, and 2009-2011 Chevrolet Silverado 2500, Silverado 3500, GMC Sierra 2500 and Sierra 3500 vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.

Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 22, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on March 1, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328760.

21V053000 · Air Bags:frontal:passenger Side:inflator Module

Feb 5, 2021

General Motors, LLC (GM) is recalling certain 2013 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2010 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2009 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C."

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.

Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 24, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on May 11, 2021. Owners may contact Cadillac customer service at 1-800-458-8006; Chevrolet customer service at 1-800-222-1020; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328790.

21V054000 · Air Bags:frontal:passenger Side:inflator Module

Feb 5, 2021

General Motors, LLC (GM) is recalling certain 2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally GM is recalling certain 2011-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, Yukon XL and 2011-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Additionally, GM is recalling certain 2010-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL and 2010-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.

Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 25, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed to 40 VIN owners on May 11, 2021. A second owner notification letter was mailed to all other owners on January 24, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328800.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

DP15004 · Rollover Side Curtain Air Bags

Opened Jun 11, 2015 · Closed Mar 7, 2017

Status: closed (inferred from source dates) · Air Bags; Air Bags:side/window; Air Bags:side/window:curtain

In June 2015, the Office of Defects Investigation (ODI) opened this Defect Petition in response to a petition (see ODI 10568388) requesting a defect investigation of several alleged defects that can cause occupant ejections during rollover crashes in certain General Motors vehicles.The petition focused on a 2011 Texas crash involving a model year 2010 Chevrolet Tahoe, which allegedly resulted in multiple occupants to be ejected.One of the ejected occupants was fatally injured.In assessing the petitioner's request, ODI reviewed information from the petitioner, technical information related to rollover side curtain air bags from General Motors (note: ODI did not request GM's field incident data), NHTSA's prior testing and evaluation work related to FMVSS No. 226 Ejection Mitigation, and potentially relevant reports in the NHTSA complaint and crash databases.Based on the information available at the present time, NHTSA does not believe that a safety-related defect currently exists in the design of the rollover side curtain air bags in the model year 2010 Chevrolet Tahoe and other similarly designed Tahoe and Yukon vehicles.Therefore, the petition is denied.However, the agency will take further action if warranted by changing future circumstances.The official petition denial, as published in the Federal Register, is available in the document file for this petition.

Additional source detail variants (3)

Air Bags

In June 2015, the Office of Defects Investigation (ODI) opened this Defect Petition in response to a petition (see ODI 10568388) requesting a defect investigation of several alleged defects that can cause occupant ejections during rollover crashes in certain General Motors vehicles.The petition focused on a 2011 Texas crash involving a model year 2010 Chevrolet Tahoe, which allegedly resulted in multiple occupants to be ejected.One of the ejected occupants was fatally injured.In assessing the petitioner's request, ODI reviewed information from the petitioner, technical information related to rollover side curtain air bags from General Motors (note: ODI did not request GM's field incident data), NHTSA's prior testing and evaluation work related to FMVSS No. 226 Ejection Mitigation, and potentially relevant reports in the NHTSA complaint and crash databases.Based on the information available at the present time, NHTSA does not believe that a safety-related defect currently exists in the design of the rollover side curtain air bags in the model year 2010 Chevrolet Tahoe and other similarly designed Tahoe and Yukon vehicles.Therefore, the petition is denied.However, the agency will take further action if warranted by changing future circumstances.The official petition denial, as published in the Federal Register, is available in the document file for this petition.

Air Bags:side/window:curtain

In June 2015, the Office of Defects Investigation (ODI) opened this Defect Petition in response to a petition (see ODI 10568388) requesting a defect investigation of several alleged defects that can cause occupant ejections during rollover crashes in certain General Motors vehicles.The petition focused on a 2011 Texas crash involving a model year 2010 Chevrolet Tahoe, which allegedly resulted in multiple occupants to be ejected.One of the ejected occupants was fatally injured.In assessing the petitioner's request, ODI reviewed information from the petitioner, technical information related to rollover side curtain air bags from General Motors (note: ODI did not request GM's field incident data), NHTSA's prior testing and evaluation work related to FMVSS No. 226 Ejection Mitigation, and potentially relevant reports in the NHTSA complaint and crash databases.Based on the information available at the present time, NHTSA does not believe that a safety-related defect currently exists in the design of the rollover side curtain air bags in the model year 2010 Chevrolet Tahoe and other similarly designed Tahoe and Yukon vehicles.Therefore, the petition is denied.However, the agency will take further action if warranted by changing future circumstances.The official petition denial, as published in the Federal Register, is available in the document file for this petition.

Air Bags:side/window

In June 2015, the Office of Defects Investigation (ODI) opened this Defect Petition in response to a petition (see ODI 10568388) requesting a defect investigation of several alleged defects that can cause occupant ejections during rollover crashes in certain General Motors vehicles.The petition focused on a 2011 Texas crash involving a model year 2010 Chevrolet Tahoe, which allegedly resulted in multiple occupants to be ejected.One of the ejected occupants was fatally injured.In assessing the petitioner's request, ODI reviewed information from the petitioner, technical information related to rollover side curtain air bags from General Motors (note: ODI did not request GM's field incident data), NHTSA's prior testing and evaluation work related to FMVSS No. 226 Ejection Mitigation, and potentially relevant reports in the NHTSA complaint and crash databases.Based on the information available at the present time, NHTSA does not believe that a safety-related defect currently exists in the design of the rollover side curtain air bags in the model year 2010 Chevrolet Tahoe and other similarly designed Tahoe and Yukon vehicles.Therefore, the petition is denied.However, the agency will take further action if warranted by changing future circumstances.The official petition denial, as published in the Federal Register, is available in the document file for this petition.