NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
1,434 reports137,000 miles · Nov 28, 2018
Service Brakes
I WAS TRAVELLING AT ROUGHLY 70 MPH ON THE FREEWAY WHEN WE ENCOUNTERED AND UNEXPECTED ROAD CREW I APPLIED MY BRAKES FIRMLY AND SLOWED TO APPROXIMATELY 40MPH AND CHANGED LANES TO AVOID THE HAZARD.. ALMOST INSTANTLY I WAS CUTOFF AT THE SLOWER SPEED AND NEEDED TO APPLY MY BRAKES AGAIN, THIS TIME THE PEDAL WAS FIRM AND THE VEHICLE …
Read full complaint
I WAS TRAVELLING AT ROUGHLY 70 MPH ON THE FREEWAY WHEN WE ENCOUNTERED AND UNEXPECTED ROAD CREW I APPLIED MY BRAKES FIRMLY AND SLOWED TO APPROXIMATELY 40MPH AND CHANGED LANES TO AVOID THE HAZARD.. ALMOST INSTANTLY I WAS CUTOFF AT THE SLOWER SPEED AND NEEDED TO APPLY MY BRAKES AGAIN, THIS TIME THE PEDAL WAS FIRM AND THE VEHICLE DID NOT REACT. I AVOIDED THE COLLISION BY SWERVING INTO THE NEXT LANE. THE PEDAL HAD NO AFFECT ON STOPPING THE VEHICLE IN THIS SITUATION.
NHTSA ODI #11154441
71,586 miles · Nov 28, 2018
Service Brakes
MY VEHICLE WAS IN MOTION I STARTED HEARING A LOUD NOISE AS I WAS COMING TO YIELD BECAUSE OF SLOW TRAFFIC IT WAS HARD FOR ME TO BRAKE I WAS HAVING DIFFICULT TIME BRAKING I WOULD HAVE TO PRESS BRAKE ALL THE WAY DOWN FOR IT TO COME TO A VERY SLOW AND LONG DISTANT STOP I HAD TO GET OFF THE HIGHWAY AND HAD TO GET MY TRUCK TOWED IT WA…
Read full complaint
MY VEHICLE WAS IN MOTION I STARTED HEARING A LOUD NOISE AS I WAS COMING TO YIELD BECAUSE OF SLOW TRAFFIC IT WAS HARD FOR ME TO BRAKE I WAS HAVING DIFFICULT TIME BRAKING I WOULD HAVE TO PRESS BRAKE ALL THE WAY DOWN FOR IT TO COME TO A VERY SLOW AND LONG DISTANT STOP I HAD TO GET OFF THE HIGHWAY AND HAD TO GET MY TRUCK TOWED IT WAS VERY DANGEROUS I TOOK IT TO THE DEALERSHIP THEY TOLD ME MY WARRANTY DIDN'T COVER IT SO I HAD TO PAY IT ENDED BEING A BRAKE HOSE THAT BUSTED I PAYED ABOUT $850 AND I HAVE THE RECEIPT FOR IT FROM THE DEALERSHIP I FELT VERY SCARED THIS SITUATION IS VERY DANGEROUS HAD TO GET A RENTAL THAT I PAYED FOR WHILE I WAITED FOR MY TRUCK TO GET REPAIRED .
NHTSA ODI #11154404
63,000 miles · Nov 27, 2018
Service Brakes
ON TWO SEPARATE OCCASIONS WHILE TRAVELING AT LOW SPEED, MY BRAKE PEDAL BECAME HARD AND WOULD NOT FUNCTION NORMALLY. AFTER USING A GREAT DEAL OF FORCE ON THE BRAKE PEDAL I WAS ABLE TO STOP THE VEHICLE BUT EXCEEDED THE DISTANCE AT WHICH I WAS TRYING TO STOP WITHIN. THANKFULLY A COLLISION DID NOT OCCUR AND THERE WAS NO HARM TO ANY…
Read full complaint
ON TWO SEPARATE OCCASIONS WHILE TRAVELING AT LOW SPEED, MY BRAKE PEDAL BECAME HARD AND WOULD NOT FUNCTION NORMALLY. AFTER USING A GREAT DEAL OF FORCE ON THE BRAKE PEDAL I WAS ABLE TO STOP THE VEHICLE BUT EXCEEDED THE DISTANCE AT WHICH I WAS TRYING TO STOP WITHIN. THANKFULLY A COLLISION DID NOT OCCUR AND THERE WAS NO HARM TO ANYONE.
NHTSA ODI #11154191
54,000 miles · Nov 26, 2018
Service BrakesSteering
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. WHILE DRIVING VARIOUS SPEEDS, A SUDDEN CHIME SOUNDED. NEXT, THE POWER STEERING AND POWER BRAKES SUDDENLY MALFUNCTIONED AND THE STEERING WHEEL BECAME DIFFICULT TO TURN IN EITHER DIRECTION. ALSO, THE BRAKE PEDAL HAD TO BE DEPRESSED WITH FORCE TO STOP THE VEHICLE. THE VEHICLE WA…
Read full complaint
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. WHILE DRIVING VARIOUS SPEEDS, A SUDDEN CHIME SOUNDED. NEXT, THE POWER STEERING AND POWER BRAKES SUDDENLY MALFUNCTIONED AND THE STEERING WHEEL BECAME DIFFICULT TO TURN IN EITHER DIRECTION. ALSO, THE BRAKE PEDAL HAD TO BE DEPRESSED WITH FORCE TO STOP THE VEHICLE. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER AND AN UNKNOWN DEALER WERE NOTIFIED OF THE FAILURES. THE FAILURE MILEAGE WAS 54,000. THE VIN WAS UNKNOWN.
NHTSA ODI #11153973
64,400 miles · Nov 26, 2018
Electrical SystemSteering
MY TRUCK HAS LOST POWER 3 TIMES WHILE DRIVING. FORTUNATELY NO ACCIDENTS HAVE HAPPENED AS A RESULT, BUT I NO LONGER FEEL SAFE IN THE VEHICLE. FIRST OCCURRENCE, I WAS IN MOTION BACKING INTO MY DRIVEWAY. SECOND OCCURRENCE, I WAS LEAVING MY NEIGHBORHOOD AND TURNING RIGHT WHEN I LOST ALL POWER AND DRIFTED INTO TRAFFIC. THIRD OCCU…
Read full complaint
MY TRUCK HAS LOST POWER 3 TIMES WHILE DRIVING. FORTUNATELY NO ACCIDENTS HAVE HAPPENED AS A RESULT, BUT I NO LONGER FEEL SAFE IN THE VEHICLE. FIRST OCCURRENCE, I WAS IN MOTION BACKING INTO MY DRIVEWAY. SECOND OCCURRENCE, I WAS LEAVING MY NEIGHBORHOOD AND TURNING RIGHT WHEN I LOST ALL POWER AND DRIFTED INTO TRAFFIC. THIRD OCCURRENCE, I WAS TURNING RIGHT INTO MY NEIGHBORHOOD AND ENDED UP ON MY NEIGHBORS FRONT LAWN. I TOOK IT TO A LOCAL CHEVROLET DEALERSHIP FOR REPAIRS, AND THE PROBLEM PERSISTS. THEY MADE 3 ATTEMPTS AT FIXING, I PAID EACH TIME, AND NOTHING HAS BEEN REPAIRED.
NHTSA ODI #11153719
61,000 miles · Nov 26, 2018
Service Brakes
BRAKE PEDAL PRESSURE SIGNIFICANTLY INCREASES AFTER A SERIES OF BRAKE APPLICATIONS AT LOW SPEED. BRAKE PEDAL BECOMES VERY FIRM AND PULSATES, STOPPING BECOMES VERY DIFFICULT. PEDAL FEEL RETURNS TO NORMAL AFTER DRIVING A SHORT DISTANCE BUT THE ISSUE RETURNS AFTER A SERIES OF BRAKE PEDAL APPLICATIONS IN A SHORT TIME SPAN. FIRST N…
Read full complaint
BRAKE PEDAL PRESSURE SIGNIFICANTLY INCREASES AFTER A SERIES OF BRAKE APPLICATIONS AT LOW SPEED. BRAKE PEDAL BECOMES VERY FIRM AND PULSATES, STOPPING BECOMES VERY DIFFICULT. PEDAL FEEL RETURNS TO NORMAL AFTER DRIVING A SHORT DISTANCE BUT THE ISSUE RETURNS AFTER A SERIES OF BRAKE PEDAL APPLICATIONS IN A SHORT TIME SPAN. FIRST NOTICED IN A PARKING LOT AS PULLING INTO A SPACE, BUT PROBLEM REPEATED ON CITY STREETS AS PULLING UP TO STOP LIGHTS OR IN CITY STOP AND GO TRAFFIC.
NHTSA ODI #11153683
47,000 miles · Nov 25, 2018
Electrical SystemElectronic Stability Control (esc)Steering
TAKATA RECALL - 2014 CHEVY SILVERADO LTZ ABOUT 6 MONTHS AGO NOW, I HAVE BEEN HAVING THIS PROBLEM AND NOW I HAVE HAD ENOUGH! WHEN TURNING ON A LOW SPEED THE STEERING WHEEL LOCKS AND SEEMS TO BOUNCE BACK. I DON'T KNOW WHAT CAUSES THIS. IT USE TO HAPPEN MAYBE 1-2 TIMES EVERY MONTH WHILE PARKING IN MY DRIVE WAY. USE TO BE ALWAYS IN …
Read full complaint
TAKATA RECALL - 2014 CHEVY SILVERADO LTZ ABOUT 6 MONTHS AGO NOW, I HAVE BEEN HAVING THIS PROBLEM AND NOW I HAVE HAD ENOUGH! WHEN TURNING ON A LOW SPEED THE STEERING WHEEL LOCKS AND SEEMS TO BOUNCE BACK. I DON'T KNOW WHAT CAUSES THIS. IT USE TO HAPPEN MAYBE 1-2 TIMES EVERY MONTH WHILE PARKING IN MY DRIVE WAY. USE TO BE ALWAYS IN MY DRIVEWAY ONLY. AND NOW THAT THANKSGIVING PASSED AND I WAS DOING SOME SHOPPING WITH MY KIDS; FROM 11/22/18-NOW 11/25/18, IT HAS LOCKED ON ME ABOUT 15 TIMES! ONCE TURNING LEFT ON A GREEN LIGHT ON A BUSY CITY STREET, IT LOCKED AND WOULDN'T TURN WAS GOING STRAIGHT WITH MY KIDS INSIDE AND MY WIFE DRIVING! ANOTHER TIME PARKING AT STORE PARKING LOTS WITH CARS IN FRONT AND BEHIND ME! AND JUST NOW 7:26 P.M. IT LOCKED 5 TIMES WHILE PARKING! I TOOK IT TO GET IT CHECKED OUT BACK IN AUGUST I BELIEVE AND ALL THEY TOLD ME WAS NOTHING IS WRONG. I CAN NOT KEEP DRIVING THIS OR HAVING MY WIFE DRIVE MY KIDS AND RISK LOOSING THEM! YOU NEED TO FIX THIS NOW! PLEASE! I BELIEVE THERE IS A RECALL GOING ARROUND; I BELIEVE THE RECALL NUMBER IS 17V414000 A LOT OF WHAT IT SAYS SOUNDS EXACTLY WHAT HAPPENS TO MY TRUCK.
NHTSA ODI #11153663
80,000 miles · Nov 25, 2018
Service Brakes
DURING LOW SPEED BRAKING POWER ASSIST IS LOST AND BRAKING IS DIFFICULT. VEHICLE TAKES LONGER TO STOP.
NHTSA ODI #11153572
80,000 miles · Nov 24, 2018
Service Brakes
DROVE 35 MILES. STOPPED OK. BACKED UP ABOUT 5 MPH. BRAKE PEDAL WOULD ONLY PUSH DOWN ABOUT ONE QUARTER INCH WITH NO BRAKING ACTION. PRESSED AS HARD AS POSSIBLE AND GOT SLIGHT BRAKING. WE HAD IT REPAIRED AT A SHOP AND THEY SAID IT WAS A VACUUM PUMP AND A SENSOR THAT HAD GONE BAD.
NHTSA ODI #11153486
87,264 miles · Nov 24, 2018
Service Brakes
ANY TIME, WHILE I AM DRIVING, THE BRAKES TURN ROCK HARD WHEN TRYING TO BRAKE. WHEN IT FIRST STARTED A LITTLE OVER A WEEK AGO, THE BRAKES WOULD ONLY TURN HARD WHEN I WAS GOING 20MPH OR SLOWER. NOW IT'S EVERYTIME I TRY TO BRAKE WHILE DRIVING. EVERY ONCE IN AWHILE IT WILL HAPPEN WHEN I AM STATIONARY. WHEN IT FIRST HAPPENED A LITTLE…
Read full complaint
ANY TIME, WHILE I AM DRIVING, THE BRAKES TURN ROCK HARD WHEN TRYING TO BRAKE. WHEN IT FIRST STARTED A LITTLE OVER A WEEK AGO, THE BRAKES WOULD ONLY TURN HARD WHEN I WAS GOING 20MPH OR SLOWER. NOW IT'S EVERYTIME I TRY TO BRAKE WHILE DRIVING. EVERY ONCE IN AWHILE IT WILL HAPPEN WHEN I AM STATIONARY. WHEN IT FIRST HAPPENED A LITTLE OVER A WEEK AGO I ALMOST HIT ANOTHER VEHICLE IN FRONT OF ME WHILE I WAS COMING TO A STOP LIGHT. IT TOOK EVERYTHING I HAD IN ME TO STOP MY VEHICLE DUE TO THE BRAKES. MY HUSBAND, WHO IS A MECHANIC, LOOKED AT MY BRAKE PADS AND THEY ARE FINE. I KEEP HAVING THE SERVICE BRAKE ASSIST BADGE POP UP ON MY DASH WHEN I HAVE TROUBLE BRAKING. THERE NEEDS TO BE A RECALL ON THIS TO FIX THE VACUUM PUMP, BRAKE BOOSTER, OR WHATEVER MAYBE CAUSING THE ISSUE. THIS HAPPENS NOW EVERYTIME I'M DRIVING ON THE HIGHWAY, COUNTRY ROAD, MY DRIVEWAY, OR TURNING. I HAVE COMPLETELY STOPPED DRIVING MY TRUCK UNTIL THE ISSUE IS FIXED, DUE TO IT BEING A SAFETY HAZARD FOR MY FAMILY AND OTHERS. I HAVE HORSES SO I USE MY TRUCK ON A DAILY OCCURRENCE TO TAKE CARE OF THEIR NEEDS. THE PROBLEM NEEDS TO BE FIXED AND A RECALL NEEDS TO HAPPEN.
NHTSA ODI #11153473
Official recalls
6Apr 8, 2021
General Motors, LLC (GM) is recalling certain 2014-2016 Chevrolet Silverado 1500, 2015-2016 Chevrolet Tahoe, and 2014-2015 GMC Sierra 1500 vehicles that may have received an incorrect replacement tensioner cable assembly as part of a previous recall remedy or a subsequent repair. The flexible steel cable connecting the driver's seat belt to the outboard side of the seat may be repeatedly bent over the seat side shield as the driver enters and exits the vehicle causing the cable to fatigue and separate.
Consequence & remedy
Consequence: A broken pretensioner cable reduces the effectiveness of the driver's seat belt, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the driver seat belt lap pretensioner, free of charge. The recall began on May 5, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212330040.
Oct 24, 2019
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence & remedy
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Additional source detail variants (3)
Service Brakes
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor/tone Ring
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Electronic Stability Control (esc)
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Sep 6, 2019
General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.
Consequence & remedy
Consequence: As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-458-8006 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192268490.
Jul 10, 2017
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Jun 29, 2017
General Motors LLC (GM) is recalling certain 2014 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles. The vehicles may have a temporary loss of electric power steering (EPS) assist, especially during low-speed turning maneuvers.
Consequence & remedy
Consequence: If EPS assist is lost and then returns, the driver might lose temporary control of the steering wheel, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will update the EPS module software, free of charge. The recall began on August 10, 2017. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-432-8782. GM's number for this recall is 17276.
Sep 8, 2016
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE18012 · Brake Vacuum Pump Failure
Opened Nov 20, 2018 · Closed Apr 10, 2022
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Additional source detail variants (3)
Service Brakes
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Illustration