NHTSA owner reports · September 18, 2026 snapshot.
Vehicle Speed Control complaints
23 reportsClear category filter62,000 miles · Mar 2, 2020
Electrical SystemSteeringVehicle Speed Control
I WAS DRIVING ON THE INTERSTATE WITH CRUISE CONTROL SET, AND WHENEVER I WOULD SIGNAL LEFT TO MERGE INTO THE OTHER LANE, THE CRUISE WOULD DISENGAGE. I COULD RESET IT AS USUAL IMMEDIATELY AFTERWARDS, BUT IT HAD DONE THIS BEFORE, SO I TESTED MULTIPLE TIMES AND RECEIVED THE SAME RESPONSE ALMOST EVERY TIME. THE DASH LIGHTS WOULD FL…
Read full complaint
I WAS DRIVING ON THE INTERSTATE WITH CRUISE CONTROL SET, AND WHENEVER I WOULD SIGNAL LEFT TO MERGE INTO THE OTHER LANE, THE CRUISE WOULD DISENGAGE. I COULD RESET IT AS USUAL IMMEDIATELY AFTERWARDS, BUT IT HAD DONE THIS BEFORE, SO I TESTED MULTIPLE TIMES AND RECEIVED THE SAME RESPONSE ALMOST EVERY TIME. THE DASH LIGHTS WOULD FLICKER, AS WELL AS MYLINK WINDOW IN CENTER CONSOLE AREA. IT WOULD ALSO GO NUTS IF I ROLLED UP THE WINDOW AND HOLD A SECOND PAST THE TIME WINDOW WAS COMPLETELY UP. I HAD MULTIPLE LIGHTS WITHIN DASH LIGHT UP, THEN GO OFF (REALLY SCARY). HAPPENED TOO FAST TO TELL WHAT LIGHTS LIT UP. ADDITIONALLY, MY POWER STEERING WENT OUT AS I WAS SLOWLY TURNING INTO DRIVEWAY OF MY FRIEND'S HOUSE. HE EVEN COMMENTED IT LOOKED LIKE I WAS HAVING TROUBLE WITH THE TURN, SO IT WASN'T JUST MY IMAGINATION. THIS EPISODE HAS HAPPENED SEVERAL TIMES BEFORE, ALMOST AS IF THE ENGINE HAD DIED (BUT IT HAD NOT DONE SO). I HAVE READ WHERE THIS WAS A RECALL ON OTHER MODELS OF CHEVY TRUCKS, BUT FOUND NO RECALL INFORMATION ON MY VIN. ALL I KNOW IS THAT IF MY ELECTRONICS AND/OR MY STEERING GO OUT WHILE GOING DOWN THE ROAD AND I WRECK, GM WILL HAVE MAJOR LEGAL ISSUES ON THEIR HANDS. I HAVE BEEN A LIFELONG CHEVY OWNER AND ALWAYS KEEP MY VEHICLES IN TIP-TOP SHAPE. THEREFORE, THIS IS A MANUFACTURER'S ISSUE THAT NEEDS RESOLVED BEFORE LIVES ARE LOST.
NHTSA ODI #11315639
64,000 miles · May 10, 2019
Vehicle Speed Control
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. THE CONTACT STATED WHILE DRIVING 45 MPH, THE ACCELERATOR PEDAL WAS DEPRESSED AND THE VEHICLE FAILED TO ACCELERATE. THE VEHICLE WAS TOWED TO LOCAL DEALER FELDMAN CHEVROLET OF LANSING (2801 E MICHIGAN AVE, LANSING, MI 48912, (517) 507-4948) WHERE THE FAILURE WAS UNABLE TO BE DE…
Read full complaint
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. THE CONTACT STATED WHILE DRIVING 45 MPH, THE ACCELERATOR PEDAL WAS DEPRESSED AND THE VEHICLE FAILED TO ACCELERATE. THE VEHICLE WAS TOWED TO LOCAL DEALER FELDMAN CHEVROLET OF LANSING (2801 E MICHIGAN AVE, LANSING, MI 48912, (517) 507-4948) WHERE THE FAILURE WAS UNABLE TO BE DETERMINED. THE CONTACT STATED HE CONTINUED TO EXPERIENCE THE FAILURE. THE MANUFACTURER WAS INFORMED OF THE FAILURE. THE FAILURE MILEAGE WAS 64,000. *JS
NHTSA ODI #11206899
40,000 miles · Dec 5, 2018
Electronic Stability Control (esc)SteeringVehicle Speed Control
LOSS OF STEERING AND POWER DEALERSHIP HAS PERFORMED RECALL 17276 REPROGRAMING POWER STEERING CONTROL MODULE TWICE AND THIS HAS NOT FIXED PROBLEM.
NHTSA ODI #11156353
101,000 miles · Sep 12, 2018
Electrical SystemSteeringVehicle Speed Control
PRODUCT SAFETY RECALL 17276 LOSS OF STEERING ASSIST -- MY TRUCK IS NOT INVOLVED IN THIS RECALL, BUT I AM HAVING THE EXACT ISSUES DESCRIBED IN THE RECALL, SUDDEN LOSS AND RETURN OF EPS ASSIST. THIS HAPPENS AT LOW SPEEDS WHEN TURNING OR BACKING, BOTH FORWARD AND REVERSE MOTIONS. I AM ALSO HAVING ISSUES WITH THE CRUISE CONTROL S…
Read full complaint
PRODUCT SAFETY RECALL 17276 LOSS OF STEERING ASSIST -- MY TRUCK IS NOT INVOLVED IN THIS RECALL, BUT I AM HAVING THE EXACT ISSUES DESCRIBED IN THE RECALL, SUDDEN LOSS AND RETURN OF EPS ASSIST. THIS HAPPENS AT LOW SPEEDS WHEN TURNING OR BACKING, BOTH FORWARD AND REVERSE MOTIONS. I AM ALSO HAVING ISSUES WITH THE CRUISE CONTROL SHUTTING OFF INTERMITTENTLY WHEN ACTIVATING THE TURN INDICATOR TO CHANGE LANES. I UNDERSTAND THAT THIS MAY BE RELATED TO THIS RECALL, AS THE ELECTRICAL SOFTWARE ISSUES CAN CAUSE OTHER ELECTRICAL SYSTEMS TO BECOME TEMPORARILY DISABLED, SUCH AS THE RADIO, STABILITRACK, DIC, CHIMES, DOOR-LOCK CYCLING, AIR CONDITIONING, OR CRUISE CONTROL. ALSO, WHEN THE TURN INDICATOR IS ACTIVATED AND THE CRUISE CONTROL SHUTS OFF, THE DASH LIGHTS ALSO FLICKER. I HAVE ALREADY HAD THIS TRUCK IN TO THE DEALER ONCE TO FIX THIS, AND THEY REFUSED TO RUN THE RECALL BECAUSE MY TRUCK WAS NOT IN THE RECALL GROUP. INSTEAD THEY CHARGED ME OVER $1,000 TO REPLACE A STEERING WHEEL POSITION SENSOR, WHICH I NOW DOUBT WAS THE PROBLEM SINCE THE ISSUES WITH LOSS OF STEERING AND DISABLING OF CRUISE CONTROL HAVE RETURNED. I JUST WANT THIS FIXED.
NHTSA ODI #11129154
75,000 miles · Aug 3, 2018
Electrical SystemEngineVehicle Speed Control
MY SILVERADO FREQUENTLY "SHUTS OFF" WHEN I AM MAKING TURNS. THIS IS EXTREMELY DANGEROUS - THE LATEST TIME I WAS PULLING OUT INTO TRAFFIC AND THE ENGINE AND ALL ELECTRICAL PARTS TURN OFF. I WAS NEARLY HIT BY ANOTHER VEHICLE. THERE WAS A RECALL FOR THIS EXACT ISSUE AND MY LOCAL CHEVROLET DEALER SAID THEY HAVE "FIXED IT". I KEE…
Read full complaint
MY SILVERADO FREQUENTLY "SHUTS OFF" WHEN I AM MAKING TURNS. THIS IS EXTREMELY DANGEROUS - THE LATEST TIME I WAS PULLING OUT INTO TRAFFIC AND THE ENGINE AND ALL ELECTRICAL PARTS TURN OFF. I WAS NEARLY HIT BY ANOTHER VEHICLE. THERE WAS A RECALL FOR THIS EXACT ISSUE AND MY LOCAL CHEVROLET DEALER SAID THEY HAVE "FIXED IT". I KEEP BRINGING THE TRUCK BACK TO THEM, BUT THEY WON'T ATTEMPT TO FIX IT AGAIN CITING LEMON LAWS BECAUSE THEY CAN'T GET THE TRUCK TO REPLICATE THE ISSUE. I AM BEYOND FRUSTRATED AND AT THIS POINT CONCERNED ABOUT THE SAFETY OF MY CHILDREN AND MYSELF AS I DRIVE.
NHTSA ODI #11115569
35,000 miles · May 12, 2018
Electronic Stability Control (esc)SteeringVehicle Speed Control
STEER ASSIST AND STABILITRAK ERRORR MESSAGES. SAYS TO SERVICE. MY A/C UNIT IS ALSO AFFECTED BY THIS. IT APPEARS THAT IT MAY HAVE BEEN PART OF THE RECALL #17276 BUT ACCORDING TO THE DEALER OUR VIN DID NOT PULL IT UP. THE VEHICLE PULLS AND STEERING BECOMES DIFFICULT. A/C UNIT BLOWS OUT HOT AIR. WHEN IN CRUISE CONTROL SOMETIMES T…
Read full complaint
STEER ASSIST AND STABILITRAK ERRORR MESSAGES. SAYS TO SERVICE. MY A/C UNIT IS ALSO AFFECTED BY THIS. IT APPEARS THAT IT MAY HAVE BEEN PART OF THE RECALL #17276 BUT ACCORDING TO THE DEALER OUR VIN DID NOT PULL IT UP. THE VEHICLE PULLS AND STEERING BECOMES DIFFICULT. A/C UNIT BLOWS OUT HOT AIR. WHEN IN CRUISE CONTROL SOMETIMES THE VEHICLE ACCELERATES ON ITS OWN AND THE RPMS SHOOT UP. HAVE TO BREAK AND DECREASE SPEED FOR PROBLEM TO BE RESOLVED BEFORE RESETTING CRUISE CONTROL.
NHTSA ODI #11093471
51,000 miles · Dec 13, 2017
EngineVehicle Speed Control
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. WHILE DRIVING AT 15-20 MPH AND APPROACHING A STOP LIGHT, THE BRAKE PEDAL WAS DEPRESSED AND THE VEHICLE ACCELERATED INTO THE TRAFFIC. IN ADDITION, THE VEHICLE THEN STALLED. THE CONTACT STATED THE VEHICLE WAS ABLE TO BE RE STARTED AND PUT IN INTO REVERSE. THE DEALER WAS CONTACT…
Read full complaint
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. WHILE DRIVING AT 15-20 MPH AND APPROACHING A STOP LIGHT, THE BRAKE PEDAL WAS DEPRESSED AND THE VEHICLE ACCELERATED INTO THE TRAFFIC. IN ADDITION, THE VEHICLE THEN STALLED. THE CONTACT STATED THE VEHICLE WAS ABLE TO BE RE STARTED AND PUT IN INTO REVERSE. THE DEALER WAS CONTACT LOCATED AT ( DEACON JONES LOCATED: 1615 SUNSET AVE, CLINTON, NC 28328) WHERE THE TECHNICIAN INFORMED THAT AN UNKNOWN PART FAILED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER HAD NOT BEEN CONTACTED. THE FAILURE MILEAGE WAS 51,000.
NHTSA ODI #11054546
51,000 miles · Apr 11, 2017
Electrical SystemElectronic Stability Control (esc)Vehicle Speed Control
WHILE DRIVING WITH CRUISE CONTROL ENGAGED AND A SIGNAL LIGHT IS USED , CRUISE IS DISENGAGED OR IF THE WINDOWS ARE ROLLED UP OR DOWN THEN CRUISE WILL BE DISENGAGED. THIS ACTION WILL ALSO CAUSE THE INSTRUMENT CLUSTER TO DIM WHEN THE SIGNAL IS USED OR WINDOWS ROLLED UP OR DOWN. IF I TURN THE VEHICLE OFF AND RESTART THE VEHICLE IT W…
Read full complaint
WHILE DRIVING WITH CRUISE CONTROL ENGAGED AND A SIGNAL LIGHT IS USED , CRUISE IS DISENGAGED OR IF THE WINDOWS ARE ROLLED UP OR DOWN THEN CRUISE WILL BE DISENGAGED. THIS ACTION WILL ALSO CAUSE THE INSTRUMENT CLUSTER TO DIM WHEN THE SIGNAL IS USED OR WINDOWS ROLLED UP OR DOWN. IF I TURN THE VEHICLE OFF AND RESTART THE VEHICLE IT WILL CLEAR UP AND MAY GO ANOTHER HOUR BEFORE IT DOES IT AGAIN. THIS IS GETTING PROGRESSIVELY WORSE AND SOMETIMES FLASHES A WARNING IN THE DRIVERS INFORMATION CENTER,STABILITRAK DISABLED AND STEERING ASSIST DISABLED DRIVE WITH CAUTION. AGAIN IF I TURN THE VEHICLE OFF AND RESTART IT IT WILL WORK JUST FINE FOR A WHILE. THIS DOES SEEM TO HAPPEN MORE WHEN I HAVE DRIVEN THE VEHICLE FOR AT LEAST ONE HOUR. THIS STARTED HAPPENING APPROX 6 MONTHS AGO WITH CRUISE BEING DISENGAGED AND THE DASH LIGHTS DIMMING WHILE USING THE SIGNAL LIGHTS OR THE WINDOW SWITCH. THE STABILITRAK AND STEERING WARNINGS STARTED 03/19/2017. ON 03/20/2017 I HAD DRIVEN THE VEHICLE ABOUT 2 MILES AND WAS PULLING INTO A PARKING SPOT AT A LOW SPEED WHEN THE STEERING WHEEL WAS RIPPED FROM MY HANDS. THE LAST INCIDENT WAS ON APRIL 8TH WHILE PULLING A TRAILER WITH THE TOW HAUL MODE ENGAGED. I WAS ATTEMPTING TO PASS A VEHICLE AND KICKED THE VEHICLE INTO PASSING GEAR WHEN THE STABILITRAK AND STEERING WARNING BOTH CAME ON .
NHTSA ODI #10971837
26,474 miles · Nov 30, 2016
Electronic Stability Control (esc)SteeringVehicle Speed Control
THIS FAILURE HAS OCCURRED QUITE A FEW TIMES. DRIVING HOME THEN TURNING LEFT THE STEERING WHEEL LOCKED UP AND SHOOK VIOLENTLY BACK AND FORTH. I ALMOST HIT A CAR IN THE OPPOSITE LANE DUE TO THE LOSS OF VEHICLE CONTROL. WHEN THIS HAPPENED THE LIGHTS ON THE DASH, RADIO, AC FAN ALL FLICKERED AND SUDDENLY THE TRUCK SHUT OFF. I TURNED…
Read full complaint
THIS FAILURE HAS OCCURRED QUITE A FEW TIMES. DRIVING HOME THEN TURNING LEFT THE STEERING WHEEL LOCKED UP AND SHOOK VIOLENTLY BACK AND FORTH. I ALMOST HIT A CAR IN THE OPPOSITE LANE DUE TO THE LOSS OF VEHICLE CONTROL. WHEN THIS HAPPENED THE LIGHTS ON THE DASH, RADIO, AC FAN ALL FLICKERED AND SUDDENLY THE TRUCK SHUT OFF. I TURNED IT BACK ON AND DROVE WITH SIMILAR ISSUES AND WARNING LIGHTS ON THE DASH TELLING ME THE STEERING ASSIST IS OFF AND SERVICE STABILITRAK. WHEN I PUSHED THE WINDOW CONTROL UP WITH THE WINDOW SHUT THE SAME THING HAPPENED AGAIN SHUTTING THE CRUISE CONTROL OFF WHEN I USED THE TURN SIGNAL. I'M WORRIED ABOUT MY FAMILY'S SAFETY THE DEALERSHIP SAID THEY COULDN'T DUPLICATE AND CAN'T "FIND THE FAULT CODE" WHICH I FIND RIDICULOUS WITH ELECTRONIC TECHNOLOGY CONTROLLING EVERYTHING. THEY SHOULD BE ABLE TO FIX THIS SERIOUS SAFETY PROBLEM. *TR
NHTSA ODI #10928724
42,000 miles · May 19, 2016
Electrical SystemUnknown Or OtherVehicle Speed Control
VEHICLE IS PRESENTLY AT THE DEALERSHIP FOR THE FIFTH TIME. WHILE DRIVING WITH CRUISE, WHEN CHANGING LANES AFTER TURN SIGNAL IS USED THE CRUISE SHUTS DOWN. ON SEVERAL OCCASIONS WHILE IN THE MIDDLE OF A TURN THE DASH LIGHTS FLASH, LOCKS FLIP UP N DOWN, STEERING WHEEL JERKS BACK N FORTH THEN VEHICLE DIES. THE INCIDENT THAT IS REASO…
Read full complaint
VEHICLE IS PRESENTLY AT THE DEALERSHIP FOR THE FIFTH TIME. WHILE DRIVING WITH CRUISE, WHEN CHANGING LANES AFTER TURN SIGNAL IS USED THE CRUISE SHUTS DOWN. ON SEVERAL OCCASIONS WHILE IN THE MIDDLE OF A TURN THE DASH LIGHTS FLASH, LOCKS FLIP UP N DOWN, STEERING WHEEL JERKS BACK N FORTH THEN VEHICLE DIES. THE INCIDENT THAT IS REASON FOR BEING IN THE SHOP NOW IS, WHILE IN A PARKING LOT, STEERING LOCKED N UNLOCKED, DOOR LOCKS AGAIN FLIPPED UP N DOWN, VEHICLE DIED WITH NO POWER. COULD NOT UNLOCK THE VEHICLE, NO POWER WHAT SO EVER, KEY WOULD NO TURN. EVENTUALLY I HEARD A PSST NOISE AND THE POWER CAME BACK. THE PREVIOUS TIMES TAKEN TO THE DEALER, I'M ALWAYS TOLD, CANNOT DUPLICATE. THIS IS A DANGER TO ME,MY FAMILY. AFTER BEING A FAITHFUL GM FAN FOR OVER 40+ YEARS THEY HAVE LOST THIS GUY TO ANOTHER MAKE OF VEHICLE, ESPECIALLY AFTER READING SO MANY OF THE SAME COMPLAINTS, AS I, WITHOUT RESOLVE. THEY HAVE LOST MY TRUST.
NHTSA ODI #10865825
Official recalls
6Apr 8, 2021
General Motors, LLC (GM) is recalling certain 2014-2016 Chevrolet Silverado 1500, 2015-2016 Chevrolet Tahoe, and 2014-2015 GMC Sierra 1500 vehicles that may have received an incorrect replacement tensioner cable assembly as part of a previous recall remedy or a subsequent repair. The flexible steel cable connecting the driver's seat belt to the outboard side of the seat may be repeatedly bent over the seat side shield as the driver enters and exits the vehicle causing the cable to fatigue and separate.
Consequence & remedy
Consequence: A broken pretensioner cable reduces the effectiveness of the driver's seat belt, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the driver seat belt lap pretensioner, free of charge. The recall began on May 5, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212330040.
Oct 24, 2019
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence & remedy
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Additional source detail variants (3)
Service Brakes
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor/tone Ring
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Electronic Stability Control (esc)
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Sep 6, 2019
General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.
Consequence & remedy
Consequence: As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-458-8006 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192268490.
Jul 10, 2017
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Jun 29, 2017
General Motors LLC (GM) is recalling certain 2014 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles. The vehicles may have a temporary loss of electric power steering (EPS) assist, especially during low-speed turning maneuvers.
Consequence & remedy
Consequence: If EPS assist is lost and then returns, the driver might lose temporary control of the steering wheel, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will update the EPS module software, free of charge. The recall began on August 10, 2017. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-432-8782. GM's number for this recall is 17276.
Sep 8, 2016
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE18012 · Brake Vacuum Pump Failure
Opened Nov 20, 2018 · Closed Apr 10, 2022
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Additional source detail variants (3)
Service Brakes
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Illustration