NHTSA owner reports · September 18, 2026 snapshot.
Power Train complaints
154 reportsClear category filter5,200 miles · Jun 29, 2015
Power Train
I HAD RECENTLY PURCHASED THE VEHICLE AND WAS COMING BACK FROM VEGAS, GOING UP A HILL THERE WAS A LITTLE BIT OF TRAFFIC I WAS PROBABLY DOING 35 TO 45 MPH AND SUDDENLY I HEARD A LOUD THUD COMING FROM THE REAR OF THE VEHICLE KIND OF LIKE WHEN YOU GET REAR ENDED AND IT DID AGAIN A FEW TIMES AFTER THAT, WHEN I TOOK THE TRUCK TO THE …
Read full complaint
I HAD RECENTLY PURCHASED THE VEHICLE AND WAS COMING BACK FROM VEGAS, GOING UP A HILL THERE WAS A LITTLE BIT OF TRAFFIC I WAS PROBABLY DOING 35 TO 45 MPH AND SUDDENLY I HEARD A LOUD THUD COMING FROM THE REAR OF THE VEHICLE KIND OF LIKE WHEN YOU GET REAR ENDED AND IT DID AGAIN A FEW TIMES AFTER THAT, WHEN I TOOK THE TRUCK TO THE LOCAL DEALERSHIP AND I EXPLAINED TO THEM WHAT HAD HAPPENED AND THEY SAY THAT IT WAS NEW VEHICLE WITH A ALL NEW DRIVETRAIN AND IT HAD A 6 SPEED TRANSMISSION AND IT WAS NORMAL.
NHTSA ODI #10730989
28,500 miles · May 20, 2015
Power TrainVehicle Speed Control
WHILE DRIVING, SLOWED THE VEHICLE DOWN TO START A DECENT IN THE ROAD, ONCE VEHICLE REACHED LEVEL GROUND, I PUSHED THE ACCELERATOR PEDAL, AND VEHICLE WOULD ONLY REV UP, WOULD NOT GOT FORWARD, WHILE IN DRIVE. THIS CONTINUED UNTIL THE VEHICLE WAS CLOSE TO 5 MPH, THEN VEHICLE STARTED MOVING AS THE ACCELERATOR PEDAL WAS PUSHED. THI…
Read full complaint
WHILE DRIVING, SLOWED THE VEHICLE DOWN TO START A DECENT IN THE ROAD, ONCE VEHICLE REACHED LEVEL GROUND, I PUSHED THE ACCELERATOR PEDAL, AND VEHICLE WOULD ONLY REV UP, WOULD NOT GOT FORWARD, WHILE IN DRIVE. THIS CONTINUED UNTIL THE VEHICLE WAS CLOSE TO 5 MPH, THEN VEHICLE STARTED MOVING AS THE ACCELERATOR PEDAL WAS PUSHED. THIS HAS HAPPENED ON SEVERAL TIMES, AND THE DEALER STATES THAT THEY CANNOT DUPLICATE THE OCCURRENCE. TRIED TO RECORD THE OCCURRENCE, BUT WITH THE CONSTANT TURNING OF THE STEERING WHEEL, MAKES IT HARD TO RECORD FOR PROOF.
NHTSA ODI #10717573
1,000 miles · May 19, 2015
Power TrainSteeringSuspension
WHEN DRIVING TRUCK ON INTERSTATE I NOTICE A VIBRATION IN THE FRONT STEERING AND WHEELS ONCE THE TRUCK GOES OVER 65 MILES PER HOUR. THIS WAS DOING IT JUST AFTER 1000 MILES.. WHEN THE ROTATED TIRES WHEN TRUCK WAS SERVICED . THE ISSUE IS STILL THERE
NHTSA ODI #10717376
18,000 miles · May 13, 2015
Power TrainSteeringSuspension
SINCE ABOUT 15000-18000 MILES THIS TRUCK VIBRATES AT MOST SPEEDS, MOST NOTICEABLE AT 65 MPH AND OVER. IT IS AT THE DEALER FOR THE SECOND TIME. THE FIRST TIME ALL THEY DID WAS BALANCE THE TIRES, BUT THE PROBLEM DIDN'T GO AWAY. THE DEALER IS STILL SCRATCHING THEIR HEADS ON THIS. THE LOANER 2015 I HAVE IS WORSE AND VIBRATES AT …
Read full complaint
SINCE ABOUT 15000-18000 MILES THIS TRUCK VIBRATES AT MOST SPEEDS, MOST NOTICEABLE AT 65 MPH AND OVER. IT IS AT THE DEALER FOR THE SECOND TIME. THE FIRST TIME ALL THEY DID WAS BALANCE THE TIRES, BUT THE PROBLEM DIDN'T GO AWAY. THE DEALER IS STILL SCRATCHING THEIR HEADS ON THIS. THE LOANER 2015 I HAVE IS WORSE AND VIBRATES AT ALL SPEEDS.....
NHTSA ODI #10716159
17,000 miles · Apr 21, 2015
EnginePower TrainSteering
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. THE CONTACT STATED THAT THE DRIVESHAFT AND STEERING COLUMN WAS REPAIRED TWICE. THE CONTACT STATED THAT THE DEALER ALSO HAD TO HAVE THE MOTOR MOUNTS REPLACED. THE CONTACT STATED THAT THE STEERING FAILED AGAIN AND THE VEHICLE COULD NOT BE TURNED. THE VEHICLE ALSO HAD A VIBRATIO…
Read full complaint
TL* THE CONTACT OWNS A 2014 CHEVROLET SILVERADO 1500. THE CONTACT STATED THAT THE DRIVESHAFT AND STEERING COLUMN WAS REPAIRED TWICE. THE CONTACT STATED THAT THE DEALER ALSO HAD TO HAVE THE MOTOR MOUNTS REPLACED. THE CONTACT STATED THAT THE STEERING FAILED AGAIN AND THE VEHICLE COULD NOT BE TURNED. THE VEHICLE ALSO HAD A VIBRATION COMING FROM THE FRONT END OF THE VEHICLE. THE VEHICLE WAS GIVEN TWO SETS OF NEW TIRES AND BOTH SETS FAILED. THE FAILURES OCCURRED EVER SINCE THE VEHICLE WAS PURCHASED. THE VEHICLE HAD NOT BEEN REPAIRED. THE FAILURE MILEAGE WAS 17,000. UPDATED 7/29/15*CN UPDATED 10/06/2017*CN
NHTSA ODI #10711992
7,725 miles · Mar 15, 2015
Power Train
WHILE DRIVING, VEHICLE WOULD QUIT PULLING, AS IF IN NEUTRAL. HAPPENED 3 TIMES IN A SHORT PERIOD OF TIME ON MAY 10,2015. NO WARNING BEFORE LOSING POWER TO WHEELS AND NO WARNING LIGHTS CAME ON THE DASH.ENGINE WAS RUNNING NORMAL BEFORE AND AFTER LOSING POWER TO THE WHEELS. I THINK THIS PROBLEM WOULD BE A SERIOUS SAFETY PROBLEM IF Y…
Read full complaint
WHILE DRIVING, VEHICLE WOULD QUIT PULLING, AS IF IN NEUTRAL. HAPPENED 3 TIMES IN A SHORT PERIOD OF TIME ON MAY 10,2015. NO WARNING BEFORE LOSING POWER TO WHEELS AND NO WARNING LIGHTS CAME ON THE DASH.ENGINE WAS RUNNING NORMAL BEFORE AND AFTER LOSING POWER TO THE WHEELS. I THINK THIS PROBLEM WOULD BE A SERIOUS SAFETY PROBLEM IF YOU WERE PULLING OUT IN TRAFFIC AND LOSS ALL POWER TO THE DRIVE. I NOW FEEL UNSAFE DURING THE VEHICLE OR TAKING IT ON TRIPS. I THINK YOU SHOULD PUT A REDALL ON THIS VEHICLE S DRIVE TRAIN, COMPUTER AND TRANSMISSION BEFORE PEOPLE ARE KILLED FROM THIS PROBLEM. *TR
NHTSA ODI #10694374
1,400 miles · Mar 14, 2015
Electrical SystemPower TrainSeats
WHILE DRIVING IN 4WD 'AUTO', OFF PAVEMENT IN WATERFRONT AREA, I DID NOT THINK 4WD WAS ENGAGING. WHEN I SHIFTED TO 4H, THE SEAT IMMEDIATELY CLAM SHELLED IN AND DOWN ON ME. I RESET SEAT, AND NOTICED MIRRORS ALSO HAD MOVED. A FEW MINUTES LATTER I TRIED THE SAME MANEUVER WHILE MOVING <5 MPH, WITH THE SAME RESULTS. I DROVE THE 20+ M…
Read full complaint
WHILE DRIVING IN 4WD 'AUTO', OFF PAVEMENT IN WATERFRONT AREA, I DID NOT THINK 4WD WAS ENGAGING. WHEN I SHIFTED TO 4H, THE SEAT IMMEDIATELY CLAM SHELLED IN AND DOWN ON ME. I RESET SEAT, AND NOTICED MIRRORS ALSO HAD MOVED. A FEW MINUTES LATTER I TRIED THE SAME MANEUVER WHILE MOVING <5 MPH, WITH THE SAME RESULTS. I DROVE THE 20+ MILES BACK HOME IN 4AUTO, BUT READY FOR A SURPRISE SHIFT INTO 4WD, WITH THE ACCOMPANYING, DANGEROUS SEAT POSITION CHANGE. IT OCCURRED 1 MORE TIME, WHILE DRIVING SLOWLY APPROACHING MY DRIVEWAY. I TRIED TO DUPLICATED IT A FEW MORE TIMES DURING A 2 WEEK PERIOD; NO OCCURRENCES. THE SALES PEOPLE TOLD ME TO USE 4AUTO AS MY REGUALR MODE. I DECIDED TO TRY 2H. NOW WHEN I GO FROM 2H TO 4AUTO, THE SEAT MOVES BACKWARD IN SHORT JOLTS. GOING TO 4H OR 4L, AS DIRECTED IN THE MANUAL, A CLAM SHELL EFFECT OCCURS. I HAVE DONE IT WITH OTHERS IN MY TRUCK, SO THEY CAN WITNESS THE SEAT TRY TO DEVOUR ME. THE LAST TIME IT HAPPENED, I LEFT IT IN THE DRIVEWAY WITH THE SEAT & MIRRORS IN THEIR FINAL POSITION, SO OTHERS COULD GET IN AND SEE IF THEY THOUGHT THEY COULD DRIVE IN THAT POSITION. I HAVE NOT SET THE SET MEMORY, AND WAS VERY CAREFUL TO NOT TOUCH ANYTHING BUT THE 4WD CONTROL WHILE CHANGING DRIVE MODES. AS AN ASIDE, I NOTICED OTHERS OWNERS HAD COMPLAINTS ABOUT THE SEATS. MY 'SAFETY ALERT' SEAT, 'HEATED AND COOLED (PERFORATED)', 'FRONT FULL FEATURE', 'LEATHER APPOINTED BUCKETS' DEVELOPED A SMALL TEAR IN THE LOWER, MIDDLE PORTION OF THE SEAT. I WANTED IT REPLACED, AND OF COURSE, THE FRIENDLY DEALERSHIP STAFF TRIED TO SAY THIS WAS 'NORMAL WEAR AND TEAR'. THIS WAS AT LESS THAN 500 MILES, 350 OF WHICH THE DEALERSHIP PUT ON WHILE DRIVING IT FROM ANOTHER DEALER. THIS TRUCK IS USED FOR PLEASURE ONLY, NOT WORK, NO TOOL POUCHES OR IN POCKETS... IF IT WASN'T SUCH A BAD EXAMPLE OF HOW CUSTOMERS ARE TREATED BY SOME DEALERSHIPS, IT WOULD BE LAUGHABLE. CURRENT MILLAGE: 1,711 MI. *TR
NHTSA ODI #10694307
1,461 miles · Feb 24, 2015
Power Train
DRIVING THROUGH THE PARKING LOT WHEN I NOTICED A LOSS OF POWER. I LOOKED DOWN AT THE DASHBOARD AND SAW THE CHECK ENGINE LIGHT WAS ON. AFTER CALLING THE DEALER, I ATTEMPTED TO DRIVE BACK HOME. THE TRUCK WOULDN'T GO PAST SECOND GEAR. I EVEN TRIED PUTTING IT ON MANUAL AND SHIFTING MYSELF. EVEN THOUGH THE LEVER WAS ON M, THE M ITS…
Read full complaint
DRIVING THROUGH THE PARKING LOT WHEN I NOTICED A LOSS OF POWER. I LOOKED DOWN AT THE DASHBOARD AND SAW THE CHECK ENGINE LIGHT WAS ON. AFTER CALLING THE DEALER, I ATTEMPTED TO DRIVE BACK HOME. THE TRUCK WOULDN'T GO PAST SECOND GEAR. I EVEN TRIED PUTTING IT ON MANUAL AND SHIFTING MYSELF. EVEN THOUGH THE LEVER WAS ON M, THE M ITSELF DID NOT LIGHT UP AND THE + - BUTTONS DID NOT WORK. THANKFULLY I MADE IT HOME WITH THE HAZARDS ON. THIS IS THE SECOND TIME DEALING WITH THIS ISSUE. THE DEALER SAID IT WAS THE TRANSMISSION CONTROL MODULE THE FIRST TIME. NOW THEY ARE SAYING IT'S THE SPEED SENSORS. *JS
NHTSA ODI #10690363
1,440 miles · Feb 20, 2015
Power Train
"CHECK ENGINE" LIGHT TURNED ON WHILE DRIVING ON THE EXPRESSWAY. I PULLED OFF THE EXIT RAMP AND CAME TO A RED LIGHT. WHEN IT TURNED GREEN, I STEPPED ON THE GAS AND THERE WAS LITTLE TO NO POWER. I PULLED INTO THE CLOSEST PARKING LOT AND TURNED THE VEHICLE OFF FOR A FEW MINUTES. TURNED IT ON AGAIN AND THE CHECK ENGINE LIGHT WAS S…
Read full complaint
"CHECK ENGINE" LIGHT TURNED ON WHILE DRIVING ON THE EXPRESSWAY. I PULLED OFF THE EXIT RAMP AND CAME TO A RED LIGHT. WHEN IT TURNED GREEN, I STEPPED ON THE GAS AND THERE WAS LITTLE TO NO POWER. I PULLED INTO THE CLOSEST PARKING LOT AND TURNED THE VEHICLE OFF FOR A FEW MINUTES. TURNED IT ON AGAIN AND THE CHECK ENGINE LIGHT WAS STILL ON. I PUT THE TRUCK IN REVERSE AND THE POWER WAS BACK TO NORMAL. I PUT IT IN DRIVE AND PULLED UP TO THE STOP SIGN WITHOUT INCIDENT. UPON MAKING A RIGHT TURN, I NOTICED THE RPMS WERE UNUSUALLY HIGH AND THE TRANSMISSION WAS NOT SHIFTING HIGHER THAN MAYBE 2ND GEAR. I PULLED INTO THE CLOSEST PARKING LOT AGAIN AND CALLED CHEVROLET TOW SERVICES AND THE DEALER WHO SOLD ME THE TRUCK AS NEW WITH 450 MILES ON THE ODOMETER. *TR
NHTSA ODI #10689701
800 miles · Nov 5, 2014
Power Train
WHILE SITTING AT A TRAFFIC LIGHT WHILE REMOVING FOOT FROM BRAKE PEDAL VEHICLE JUMP FORWARD (AS BEING REAR ENDED) AT OTHER TIMES AT LOW SPEEDS WHILE PARKING VEHICLE LUNGES FORWARD. VEHICLE ACTS LIKE TRANSMISSION IS SLIPPING THEN LUNGES FORWARD. TOOK VEHICLE TO DEALERSHIP AND THEY REPORTED THAT PROBLEMS ARE A NORMAL AND ARE A NOR…
Read full complaint
WHILE SITTING AT A TRAFFIC LIGHT WHILE REMOVING FOOT FROM BRAKE PEDAL VEHICLE JUMP FORWARD (AS BEING REAR ENDED) AT OTHER TIMES AT LOW SPEEDS WHILE PARKING VEHICLE LUNGES FORWARD. VEHICLE ACTS LIKE TRANSMISSION IS SLIPPING THEN LUNGES FORWARD. TOOK VEHICLE TO DEALERSHIP AND THEY REPORTED THAT PROBLEMS ARE A NORMAL AND ARE A NORMAL CHARACTERISTIC OF VEHICLE OPERATING AS DESIGNED. DEALERSHIP THEN GAVE ME A LIST OF SERVICE BULLETINS OF PAST ISSUES THAT WERE NOT PART OF MY ORIGINAL COMPLAINT. VEHICLE PROBLEMS STARTED WITH LESS THAN 800 MILES NOW HAS 1800. VEHICLE PROBLEM IS INTERMITTENT. *TR
NHTSA ODI #10652812
Official recalls
6Apr 8, 2021
General Motors, LLC (GM) is recalling certain 2014-2016 Chevrolet Silverado 1500, 2015-2016 Chevrolet Tahoe, and 2014-2015 GMC Sierra 1500 vehicles that may have received an incorrect replacement tensioner cable assembly as part of a previous recall remedy or a subsequent repair. The flexible steel cable connecting the driver's seat belt to the outboard side of the seat may be repeatedly bent over the seat side shield as the driver enters and exits the vehicle causing the cable to fatigue and separate.
Consequence & remedy
Consequence: A broken pretensioner cable reduces the effectiveness of the driver's seat belt, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the driver seat belt lap pretensioner, free of charge. The recall began on May 5, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212330040.
Oct 24, 2019
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence & remedy
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Additional source detail variants (3)
Service Brakes
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor/tone Ring
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Electronic Stability Control (esc)
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Sep 6, 2019
General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.
Consequence & remedy
Consequence: As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-458-8006 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192268490.
Jul 10, 2017
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Jun 29, 2017
General Motors LLC (GM) is recalling certain 2014 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles. The vehicles may have a temporary loss of electric power steering (EPS) assist, especially during low-speed turning maneuvers.
Consequence & remedy
Consequence: If EPS assist is lost and then returns, the driver might lose temporary control of the steering wheel, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will update the EPS module software, free of charge. The recall began on August 10, 2017. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-432-8782. GM's number for this recall is 17276.
Sep 8, 2016
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE18012 · Brake Vacuum Pump Failure
Opened Nov 20, 2018 · Closed Apr 10, 2022
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Additional source detail variants (3)
Service Brakes
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Illustration