2010 Chevrolet Camaro

CAR WILL NOT GO INTO FIRST OR REVERSE. SHIFTS FINE IN OTHER GEARS AND WHEN CAR TURNED OFF. TOOK TO DEALER WHO SAID CLUTCH WAS WORN AT 50,000 MILES BECAUSE I WAS TOO HARD ON IT? I DON'T RACE, HOT ROD ETC, THAT'S WHY I BOUGHT A V6 MANUAL FOR DURABILITY. AM ONLY OWNER ONLY DRIVER. THIS IS NOT MY FIRST MANUAL TRANSMISSION VEHICLE AND TO HAVE A CLUTCH GO BAD AT 50,000 MILES IS PRE-MATURE AND UNACCEPTABLE AND COSTING $1700.00 GM IS THE ONLY ONES MAKING CLUTCH SO I WAS FORCED TO GO TO DEALER AND PAY FOR REPAIRS FOR A FACTORY ISSUE THAT CAUSED EARLY CLUTCH BURN OUT AND FALSE "OK" DIAGNOSTIC ON TRANSMISSION. TURNS OUT ALOT OF OTHER OWNERS ARE HAVING THE SAME PROBLEM AND ITS COSTING US $$$. ANY MECHANIC DRIVING THIS CAR SAID "THIS IS A TRANSMISSION ISSUE, NOT A CLUTCH". A CAR NOT GOING INTO GEAR IS NOT THE CLUTCH. THERE WAS NO GRINDING OF GEARS, IT JUST WOULDN'T GO DESPITE FORCE AND CLUTCH PUSHED ALL THE WAY IN NUMEROUS TIMES. *TR

BOLTS ON THE DRIVE SHAFT ARE DEFECTIVE AND BREAKING OFF THE DRIVE SHAFT. CAR BEGINS TO VIBRATE HEAVILY ON STICK SHIFT AND STEERING WHEEL. IT IS ALSO REPRESENTED AND EQUALLY EXPLAINED ON OTHER WEB PAGES REGARDING THE CHEVROLET, CAMARO PRODUCTS, SAME YEAR OR NEWER. AFTER INSPECTION TWO OF THREE NUTS AND BOLTS EITHER BROKE OFF OR CAME OFF, LEAVING ONE BOLT TO CONTROL THE TORQ AND HORSE POWER TRAVELING DOWN THE DRIVE SHAFT. VEHICLE WAS HARD TO MANEUVER AND CLEAR OFF THE ROAD TO A SAFE LOCATION. *TR

AT 3900 MILES, THE RIGHT REAR HALFSHAFT DRIVE AXLE FAILED ON 11/04/10. AT 6907 MILES, THE CAR SUFFERED ANOTHER CATASTROPHIC POWERTRAIN FAILURE. THE FULL EXTENT OF THE DAMAGE HAS YET TO BE DETERMINED. THE KNOWN DAMAGE INCLUDED, DRIVESHAFT, TRANSMISSION, TRANSMISSION SHIFTER, AND EXHAUST. THE FAILURE OCCURRED DURING 5PM RUSH HOUR TRAFFIC AT @ 35MPH, WITH A GRINDING NOISE, AND VIBRATION AS THE ONLY INDICATORS THAT A FAILURE WAS IMMINENT. THE FAILURE OCCURRED WITH TRAFFIC SURROUNDING THE VEHICLE AT A RELATIVELY SLOW SPEED. HAD THE SAME FAILURE OCCURRED AT 55MPH, OR INTERSTATE SPEEDS IN EXCESS OF 55MPH, THE OUTCOME COULD HAVE INVOLVED FATALITIES.

TRIED TO SHIFT GEAR TO FIRST BUT THE GEAR WOULDN'T ENGAGE. CLUTCH PEDAL WAS STUCK TO THE FLOOR AND NOT RELEASING. TOWED CAR TO DEALERSHIP AND AFTER INSPECTION I WAS INFORMED THAT THE CLUTCH WAS WORN AND THE PRESSURE PLATE AND FLYWHEEL HAD TO BE REPLACED. FINAL COST $1965.77. NOT COVERED UNDER WARRANTY. 10/15/11 THE SAME PROBLEM HAS OCCURRED LESS THAN THIRTY DAYS AFTER REPAIRS. DROVE CAR 200 YARDS AND CLUTCH PEDAL WAS STUCK ONCE AGAIN, GEAR WONT ENGAGE. DISCOVERED FLUID LEAKAGE. TAKING CAR BACK TO DEALERSHIP HOPING TO GET A REFUND. *TR

I HAVE BEEN EXPERIENCING AN INTERMITTENT PROBLEM WHEN SHIFTING FROM 1ST TO 2ND GEAR. WHILE MERGING INTO TRAFFIC FROM A STOP AND GOING INTO 2ND GEAR IT GRINDS AND IS DIFFICULT TO GO INTO GEAR. THIS PROBLEM CAUSES ME TO LET OFF THE GAS AND THE RE-COMPRESS THE CLUTCH AND TRY TO PUT THE CAR INTO 2ND GEAR. DUE TO MY DECREASE OF SPEED AND ATTEMPTING TO MERGE INTO TRAFFIC THIS COULD CAUSE A SERIOUS ACCIDENT WHEN THE GRIND HAPPENS. I HAVE REPORTED MY PROBLEM TO GM CUSTOMER SERVICE AND HAVE NOT HEARD ANYTHING ABOUT WHAT THEY ARE GOING TO DO TO FIX THIS PROBLEM. THERE HAS NOT BEEN ANY CORRECTIVE ACTION BY GM. WHILE DRIVING I TAKE EXTRA PRECAUTION TO ENSURE THERE IS NO VEHICLES AROUND WHEN I TURN AT AN INTERSECTION OR WHEN MERGING INTO TRAFFIC ON THE HIGHWAY. I HAVE READ THAT THERE IS A SIMILAR PROBLEM WITH OTHER CAR MANUFACTURERS WITH THIS TRANSMISSION AND THEY HAVE CORRECTED THE PROBLEM OR ARE IN THE PROCESS OF CORRECTING THE PROBLEM ON THEIR VEHICLES. *TR

I HAVE A 2010 CAMARO WITH THE AY6 MANUAL TRANSMISSION AND V6 MOTOR. I HAD THE PRESSURE PLATE BOLTS REPLACED UNDER WARRANTY AFTER MY TRANSMISSION FAILED TO SHIFT INTO FIRST,SECOND,OR ANY OF THE OTHER GEARS SUDDENLY AFTER 14,000MILES OF ADULT DRIVEN NORMAL USE..THE TECH FROM GM TOLD ME THE BOLTS WERE NOT TORQUED DOWN FROM THE FACTORY(AISIN/WARNER) AND HAD BEEN REDESIGNED BY GM.....OK. AFTER RESEARCHING THIS MATTER FURTHER I'VE FOUND THAT HUNDREDS OF PEOPLE HAVE BEEN HAVING MULTIPLE PROBLEMS WITH THIS TRANSMISSION AND THE DEALERS AND GM ARE TRYING TO IGNORE THAT THE PROBLEM EXISTS. THIS TRANSMISSION HAS A FACTORY TORQUE RATING THAT IS 273 FT LBS AND THE GM 3.6 VVT MOTOR THAT IS IN OUR CAMAROS PUTS OUT 278 FT LBS FROM THE FACTORY.SO RIGHT OFF THE BAT THE TRANS IS DESTINED TO FAIL PREMATURELY FROM THIS OBVIOUS PROBLEM AND THEY ARE TRYING TO PASS THE COST OFF TO THE CUSTOMER IN ALOT OF CASES.I WAS ONE OF THE FORTUNATE ONES WHO HAD THE FIRST PROBLEM COVERED BUT NOW IM AFRAID TO DRIVE THE CAR LIKE A SPORTS CAR IN FEAR OF FACING THOUSANDS OF DOLLARS IN REPAIRS DUE TO GMS IRRESPONSIBLE ACTIONS BY PLACING AN INADEQUATE TRANSMISSION INTO AN AMAZING CAR.IM SURE YOUR AWARE OF THE PROBLEM FROM THE OTHER COMPLAINTS FILED BUT I KNOW FOR A FACT THAT NOT ALL HAVE WENT THIS FAR AS TO CONTACT YOU ON THIS SITUATION. THERE ARE FOUR TSBS OUT ON THIS PRESSURE PLATE ISSUE ALONE AS WELL AS OTHER MULTIPLE PROBLEMS THAT OTHERS ARE HAVING WITH THIS TRANSMISSION AND I TRULY FEEL THIS CAN BECOME A SERIOUS SAFETY ISSUE AND A PROBLEM THAT NEEDS TO BE ADDRESSED BY GENERAL MOTORS AND NOT AT THE EXPENSE OF THE PEOPLE WHO BELIEVED IN BUYING AN AMERICAN PRODUCT ONLY TO FIND OUT THAT THIS MAJOR FLAW IN PLANNING AND PURCHASING FROM AISIN/WARNER IS HAPPENING TO THE PUBLIC AND PEOPLE THROUGHOUT THE WORLD WHO PURCHASED THIS CAR. THANK YOU FOR YOUR HELP AND UNDERSTANDING AND I HOPE THIS HELPS IN RESOLVING THIS PROBLEM WITH GENERAL MOTORS. *TR