NHTSA owner reports · September 18, 2026 snapshot.
Power Train complaints
4 reportsClear category filter52,000 miles · Jan 29, 2021
Electrical SystemEnginePower Train
I WAS DRIVING ON THE FREEWAY ACCELERATING WHEN I HIT APPROXIMATELY 75 MPH MY CAR WAS MAKING A LOUD REVVING SOUND AND METAL CLANKING SOUND IN MIDDLE AND SMOKE WAS COMING FROM THE FRONT AND BACK OF THE VEHICLE VERY THICK WHITE SMOKE ALL OF A SUDDEN MY CAR SLOWED DOWN AND ALL THE LIGHTS WERE BLINKING ON THE DASH ALMOST GOT INTO ACC…
Read full complaint
I WAS DRIVING ON THE FREEWAY ACCELERATING WHEN I HIT APPROXIMATELY 75 MPH MY CAR WAS MAKING A LOUD REVVING SOUND AND METAL CLANKING SOUND IN MIDDLE AND SMOKE WAS COMING FROM THE FRONT AND BACK OF THE VEHICLE VERY THICK WHITE SMOKE ALL OF A SUDDEN MY CAR SLOWED DOWN AND ALL THE LIGHTS WERE BLINKING ON THE DASH ALMOST GOT INTO ACCIDENTS WHILE CARS AVOID HITTING! MY CAR WASN'T GOING OVER 5 10 MPH THERE WAS SO MUCH SMOKE WAS GETTING WORRIED,SOME HOW I MANAGED TO EXIT THE FREEWAY AND PARKED I WAS TOLD MY ENGLISH WAS BLOWN! MAINTENANCE WAS UP-TO-DATE ONLY DROVE IT ON THE WEEKENDS ONLY HAD 52,000 MILES NIGHTMARE 2011 BMW M3
NHTSA ODI #11390611
44,000 miles · Nov 27, 2014
Electrical SystemEnginePower Train
2011 BMW DCT M3 ENGINE TURNS OFF BY IT SELF WHILE DRIVING THROUGH INTERSECTION. TRANSMISSION GOES INTO NEUTRAL. "N" POPS UP ON THE CENTER COCKPIT. STEERING WHEEL LOCK. BRAKES WORK. HAD TO MAINTAIN FOOT ON BRAKES. HAVE TO PUSH "ENGINE START" BUTTON. CAR STARTS UP AGAIN. ENGINE STALLING AND SHUTTING OFF IS A SAFETY HAZ…
Read full complaint
2011 BMW DCT M3 ENGINE TURNS OFF BY IT SELF WHILE DRIVING THROUGH INTERSECTION. TRANSMISSION GOES INTO NEUTRAL. "N" POPS UP ON THE CENTER COCKPIT. STEERING WHEEL LOCK. BRAKES WORK. HAD TO MAINTAIN FOOT ON BRAKES. HAVE TO PUSH "ENGINE START" BUTTON. CAR STARTS UP AGAIN. ENGINE STALLING AND SHUTTING OFF IS A SAFETY HAZARD, ESPECIALLY IF THE CAR IS IN MOTION. COULD CAUSE DEATH TO END USERS OR OTHER PEOPLE. CAN CAUSE PROPERTY DAMAGES AS WELL. THIS HAS HAPPEN TWICE WITHIN A 8 WEEK PERIOD. MOST RECENTLY ON NOV 26,2014 APPROXIMATELY 430PM BMW "AUTO START STOP FUNCTION" RULED OUT BECAUSE THE LED LIGHT ABOVE THE BUTTON IS LIT, FUNCTION IS DISABLE. *TR
NHTSA ODI #10661151
8,200 miles · Oct 8, 2012
Power TrainVehicle Speed Control
THE PROBLEM OCCURS WHEN YOU SLOW DOWN- LIKE FOR A TURN, BUT DO NOT COME TO A COMPLETE STOP. THE DCT TRANSMISSION SEEMS TO HAVE TROUBLE FIGURING OUT WHAT GEAR TO SELECT BECAUSE WHEN YOU STEP ON THE GAS TO ACCELERATE, THERE IS A VERY SIGNIFICANT DELAY IN THE ONSET OF POWER- UP TO 2-3 SECONDS. BY THIS TIME, THE DRIVER IS USUALLY RE…
Read full complaint
THE PROBLEM OCCURS WHEN YOU SLOW DOWN- LIKE FOR A TURN, BUT DO NOT COME TO A COMPLETE STOP. THE DCT TRANSMISSION SEEMS TO HAVE TROUBLE FIGURING OUT WHAT GEAR TO SELECT BECAUSE WHEN YOU STEP ON THE GAS TO ACCELERATE, THERE IS A VERY SIGNIFICANT DELAY IN THE ONSET OF POWER- UP TO 2-3 SECONDS. BY THIS TIME, THE DRIVER IS USUALLY REALLY DIGGING INTO THE THROTTLE. THE TRANSMISSION FINALLY PICKS A GEAR, WHICH RESULTS IN THE CAR SUDDENLY LURCHING FORWARD, SOMETIMES INVOKING THE ANTI-SKIP CONTROL. THE DANGER IN THIS BEHAVIOR OCCURS WHEN MAKING A TURN INTO ON-COMING TRAFFIC AFTER SLOWING DOWN TO AROUND 10-15 MPH. AFTER THE TURN, THE CAR IS POSITIONED IN THE TRAFFIC LANE, BUT YOU HAVE NO POWER TO ACCELERATE INTO THE FLOW OF TRAFFIC. THE ONCOMING CARS ARE NOW CLOSING IN ON YOUR CAR AT A FAST RATE, AND YOU'RE BASICALLY STUCK. THIS SITUATION IS MOST PRONOUNCED IN THE "AUTO" MODE OF THE DCT TRANSMISSION, BUT ALSO OCCURS TO A LESSER DEGREE WHILE IN THE MANUAL MODE WHEN YOU SELECT SECOND GEAR IN PREPARATION FOR THE TURN. IT IS ALSO VERY REPEATABLE IN BOTH MODES. THESE PROBLEMS STARTED OCCURRING AFTER A PREVIOUS RECALL ON THIS TRANSMISSION WHERE THE ENGINE WOULD STALL UNDER HARD BRAKING OR NOT SHIFT UNDER HARD BRAKING. THE RECALL FIXED THAT PROBLEM, BUT INTRODUCED THIS PROBLEM, WHICH OCCURS ALMOST EVERY DAY WHEREAS THE PREVIOUS PROBLEM ONLY OCCURRED DURING A SPECIFIC SITUATION. *TR
NHTSA ODI #10479293
10,000 miles · Dec 3, 2011
Power Train
CLUNKING NOISE AND VIBRATION WHEN TURNING RIGHT FROM A STOP IN COOLER TEMPERATURES. *TR
NHTSA ODI #10438472
Official recalls
4Jan 15, 2020
BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i xDrive and M3, 2009-2011 335D, 2006-2012 325xi, 328i, 328xi and 328i xDrive, 2010-2011 X6 ActiveHybrid, 2007-2013 328i, 335i, 335is, M3 Coupes, X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M, 2009-2013 X5 xDrive35d and 2008-2014 X6 xDrive35i, X6 xDrive50i and X6M vehicles equipped with non-desiccated driver frontal air bag inflators containing phase stabilized ammonium nitrate (PSAN) that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver air bag. On X5 and X6 vehicles, only the inflator will be replaced. All repairs will be performed free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.
Jun 19, 2019
BMW of North America, LLC (BMW) is recalling certain 2009 328i and 328xi, 2009-2011 335d, 2008-2012 M3 Coupe and M3 Convertible, and 2008-2011 M3 Sedan vehicles. The connection of the positive battery cable at the fuse box terminal may degrade, resulting in an intermittent loss of electrical power.
Consequence & remedy
Consequence: A loss of electrical power can cause the vehicle to stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace and secure the positive battery cable connector, free of charge. The recall began August 14, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of a previous recall, number 18V-314.
Additional source detail variants (3)
Electrical System:wiring:fuses And Circuit Breakers
BMW of North America, LLC (BMW) is recalling certain 2009 328i and 328xi, 2009-2011 335d, 2008-2012 M3 Coupe and M3 Convertible, and 2008-2011 M3 Sedan vehicles. The connection of the positive battery cable at the fuse box terminal may degrade, resulting in an intermittent loss of electrical power.
Consequence: A loss of electrical power can cause the vehicle to stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace and secure the positive battery cable connector, free of charge. The recall began August 14, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of a previous recall, number 18V-314.
Electrical SYSTEM:12V/24V/48V Battery:cables
BMW of North America, LLC (BMW) is recalling certain 2009 328i and 328xi, 2009-2011 335d, 2008-2012 M3 Coupe and M3 Convertible, and 2008-2011 M3 Sedan vehicles. The connection of the positive battery cable at the fuse box terminal may degrade, resulting in an intermittent loss of electrical power.
Consequence: A loss of electrical power can cause the vehicle to stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace and secure the positive battery cable connector, free of charge. The recall began August 14, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of a previous recall, number 18V-314.
Electrical System
BMW of North America, LLC (BMW) is recalling certain 2009 328i and 328xi, 2009-2011 335d, 2008-2012 M3 Coupe and M3 Convertible, and 2008-2011 M3 Sedan vehicles. The connection of the positive battery cable at the fuse box terminal may degrade, resulting in an intermittent loss of electrical power.
Consequence: A loss of electrical power can cause the vehicle to stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace and secure the positive battery cable connector, free of charge. The recall began August 14, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of a previous recall, number 18V-314.
Oct 25, 2017
BMW of North America, LLC (BMW) is recalling certain 2006-2011 323i, 325i, 325xi, 328i, 328xi, 330i, 330xi, 335i, 335xi and M3, 2007-2011 328i xDrive, 335i xDrive and 335is and 2009-2011 335d vehicles. The wiring and electrical connectors for the system that controls air flow for the heating and air conditioning system may overheat.
Consequence & remedy
Consequence: Wiring that overheats could cause the electrical connectors to melt, and increase the risk of a fire, even when the vehicle is unattended.
Remedy: BMW will notify owners, and dealers will replace the wiring and electrical connectors, free of charge. Interim letters were mailed on November 27, 2017. Owners will receive a second notice when the remedy becomes available. Owners may contact BMW customer service at 1-800-525-7417.
Feb 5, 2016
BMW of North America, LLC (BMW) is recalling certain model year 2008-2013 128i and 135i coupes and convertibles and 1 Series M coupes, 2006-2011 325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi, 335i, 335xi, 335i xDrive Sedans, 2009-2011 335d sedans, 2006-2012 325xiT, 328i and 328xi sports wagons, 2007-2013 328i, 328xi, 328i xDrive, 335i, 335xi, 335i xDrive, 335is and M3 Coupes and Convertibles, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i SAVs, 2007-2010 X3 xDrive30i SAVs, 2007-2013 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5 M SAVs, 2009-2013 BMW X5 xDrive35d SAVs, 2008-2014 X6 xDrive35i, X6 xDrive50i, and X6 M SACs, 2010-2011 BMW X6 xDrive50i SACs and 2008-2011 M3 Sedan vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's frontal air bag module or inflator depending on the vehicle model, free of charge. The recall began March 9, 2018. Owners may contact BMW customer service at 1-800-525-7417.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration