NHTSA owner reports · September 18, 2026 snapshot.
Electrical System complaints
6 reportsClear category filter84,000 miles · Jul 29, 2021
Electrical SystemExterior Lighting
The contact owns a 2009 BMW M3. The contact stated while operating the vehicle, the driver’s and passenger’s side turn signal failed to illuminate. Additionally, the headlights and dashboard lights would flicker on and off. Upon inspection, it was discovered that the electrical wiring insulation was frayed and damaged. The cause…
Read full complaint
The contact owns a 2009 BMW M3. The contact stated while operating the vehicle, the driver’s and passenger’s side turn signal failed to illuminate. Additionally, the headlights and dashboard lights would flicker on and off. Upon inspection, it was discovered that the electrical wiring insulation was frayed and damaged. The cause of the failure was not yet determined. The manufacturer and local dealer were not notified of the failure. The failure mileage was approximately 84,000.
NHTSA ODI #11427001
58,500 miles · May 23, 2017
Electrical System
VEHICLE WOULD NOT START AND ALL ELECTRICAL SYSTEMS WERE DEAD DESPITE A GOOD BATTERY. WAS SOLVED BY REMOVING GLOVE BOX AND FUS BOX AND PUSHING ON THE BATTERY CABLE THAT GOES INTO THE FUSE BOX TO GET A CONNECTION. THIS IS A KNOW ISSUE FOR BMW AND A RECALL WAS ISSUED ON OTHER 3-SERIES VEHICLES (2007 - 2011) WITH THE SAME PART NUM…
Read full complaint
VEHICLE WOULD NOT START AND ALL ELECTRICAL SYSTEMS WERE DEAD DESPITE A GOOD BATTERY. WAS SOLVED BY REMOVING GLOVE BOX AND FUS BOX AND PUSHING ON THE BATTERY CABLE THAT GOES INTO THE FUSE BOX TO GET A CONNECTION. THIS IS A KNOW ISSUE FOR BMW AND A RECALL WAS ISSUED ON OTHER 3-SERIES VEHICLES (2007 - 2011) WITH THE SAME PART NUMBERS, BUT WILL NOT COVER M3. THIS IS A SAFETY ISSUE AS LOSS OF POWER TO FUSE BOX WHILE DRIVING CAN SHUT DOWN THE CAR.
NHTSA ODI #10991274
36,800 miles · Mar 24, 2015
Electrical System
WHILE TRYING TO EXIT MY E92 2009 M3 FROM INSIDE THE VEHICLE BY DOUBLE PULLING THE HANDLE IT WOULD NOT UNLOCK THE CAR. THE LOCKING BOLT STICKS UP PARTIALLY WHEN YOU PULL THE HANDLE BUT DOESN'T UNLOCK. I HAD TO HIT THE LOCK BUTTON FROM THE DASHBOARD TO UNLOCK THE CAR. THIS IS A SAFETY CONCERN IF YOU ARE PANICKED AND CAN'T GET O…
Read full complaint
WHILE TRYING TO EXIT MY E92 2009 M3 FROM INSIDE THE VEHICLE BY DOUBLE PULLING THE HANDLE IT WOULD NOT UNLOCK THE CAR. THE LOCKING BOLT STICKS UP PARTIALLY WHEN YOU PULL THE HANDLE BUT DOESN'T UNLOCK. I HAD TO HIT THE LOCK BUTTON FROM THE DASHBOARD TO UNLOCK THE CAR. THIS IS A SAFETY CONCERN IF YOU ARE PANICKED AND CAN'T GET OUT OF THE VEHICLE UNDER HEAVY STRESS. *TR
NHTSA ODI #10701509
50,400 miles · Jan 21, 2014
Electrical System
400 MILES OUT OF WARRANTY, THE ELECTRICAL SYSTEM FAULT WARNING BEGAN TO COME ON. WHEN THIS HAPPENS ALL GAUGES BOTTOM OUT QUICKLY THEN RETURN TO NORMAL. SOMETIMES, THE RESTRAINT SYSTEM, EDC OR OTHER WARNINGS WILL START. I DON'T EXPERIENCE ANY PROBLEMS DRIVING THE VEHICLE. THE BATTERY HAS BEEN REPLACED AND ALTERNATOR HAS BEEN T…
Read full complaint
400 MILES OUT OF WARRANTY, THE ELECTRICAL SYSTEM FAULT WARNING BEGAN TO COME ON. WHEN THIS HAPPENS ALL GAUGES BOTTOM OUT QUICKLY THEN RETURN TO NORMAL. SOMETIMES, THE RESTRAINT SYSTEM, EDC OR OTHER WARNINGS WILL START. I DON'T EXPERIENCE ANY PROBLEMS DRIVING THE VEHICLE. THE BATTERY HAS BEEN REPLACED AND ALTERNATOR HAS BEEN TESTED AND IS PERFORMING AS IT SHOULD. WHEN CONNECTED TO THE BMW COMPUTER FOR ERROR CODES IT DOESN'T SHOW ANY CODES OR THAT THE WARNINGS HAVE GONE OFF. I HAVE DRIVEN IT FOR 18000 MILES TRYING TO FIND JUST ONE COMMON THING THAT WILL MAKE THIS HAPPEN. I HAVE FOUND NOTHING TO CAUSE THIS WARNING. IT MAY GO OFF CONSTANTLY ONE DAY AND NOT HAPPEN AGAIN FOR 2 WEEKS. SOMETIMES, AFTER GOING OFF FOR SEVERAL TIMES, THE GAUGES FOR RPM, TEMP WILL DROP TO THEIR LOWEST INDICATIONS AND THE SPEEDOMETER WILL STICK AT WHATEVER THE SPEED IS AT THE TIME. I HAVE EMAILED BMW OF NA AND THEY INFORMED ME THAT THE RECENT RECALL FOR THIS PROBLEM DOES NOT INCLUDE THE M SERIES. I WAS TOLD THAT IT COULD COST UP TOWARDS $5000 TO FIND A LOOSE WIRE. DIDN'T THINK I SHOULD HAVE TO PAY THAT MUCH SINCE IT WAS JUST 400 MILES OUT OF WARRANTY. I DON'T THINK THAT IT IS A LOOSE WIRE BECAUSE I WOULD HAVE NOTICED THAT AS A COMMON FACTOR, LIKE HITTING A BUMP IN THE ROAD. AFTER READING MANY BMW FORUMS, THIS SEEMS TO BE A PROBLEM ASSOCIATED WITH THE M3 AS WELL AS THE OTHER SERIES. *TR
NHTSA ODI #10560764
36,300 miles · Oct 6, 2011
Electrical SystemVehicle Speed ControlCrash
SHORTLY AFTER PURCHASING MY BMW 2009 M3, I NOTICED A RARE BUT VERY DISTURBING PATTERN ON TAKE OFF. I HAD CAR CHECKED IN DEALER AND I WAS TOLD IT WAS LIKELY SECONDARY TO MY DRIVING STYLE! THIS UNCONTROLLED TAKE OFF IS LIKE HI REV AND RAPID ACCELERATION PERIODICALLY ALTERNATING WITH DECELERATION FOR FEW SECONDS. I HAD THIS HAPPEN…
Read full complaint
SHORTLY AFTER PURCHASING MY BMW 2009 M3, I NOTICED A RARE BUT VERY DISTURBING PATTERN ON TAKE OFF. I HAD CAR CHECKED IN DEALER AND I WAS TOLD IT WAS LIKELY SECONDARY TO MY DRIVING STYLE! THIS UNCONTROLLED TAKE OFF IS LIKE HI REV AND RAPID ACCELERATION PERIODICALLY ALTERNATING WITH DECELERATION FOR FEW SECONDS. I HAD THIS HAPPEN PROB A DOZEN TIME SO FAR(36K ON CAR). ON DAY OF MY ACCIDENT, IN STOP AND GO TRAFFIC WITH SPEED LESS THAN 5 MILES PER HOUR, CAR LITERALLY WENT OFF ON ME. IT ACCELERATED TO HIT THE CAR IN FRONT AND THEN MANAGED TO PUSH THE CAR INTO ANOTHER 3 CARS IN FRONT, BEFORE IT CAME TO A STALL. I AM NOT SURE IF IT WAS EXACTLY LIKE MY PREVIOUS EPISODES BECAUSE THE DISTANCE BETWEEN MY CAR AND NEXT CAR WAS SHORT. WHAT I AM SURE IS THAT I HAD NO CONTROL ON CAR. *TR
NHTSA ODI #10428888
Mileage unknown · Apr 15, 2009
Electrical System
ON A 2002 BMW 325I TAIL LIGHT SOCKET OVER HEATS DUE TO IMPROPER GROUNDING AND BURNS OUT. CAUSES THE TAIL LIGHT AND BLINKERS TO MALFUNCTION. DEALERS CHARGING UPWARDS OF $600 (EACH SIDE ) TO FIX THE WIRING THAT CERTAINLY IS A SAFETY ISSUE. *TR
NHTSA ODI #10265523
Official recalls
5Jan 15, 2020
BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i xDrive and M3, 2009-2011 335D, 2006-2012 325xi, 328i, 328xi and 328i xDrive, 2010-2011 X6 ActiveHybrid, 2007-2013 328i, 335i, 335is, M3 Coupes, X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M, 2009-2013 X5 xDrive35d and 2008-2014 X6 xDrive35i, X6 xDrive50i and X6M vehicles equipped with non-desiccated driver frontal air bag inflators containing phase stabilized ammonium nitrate (PSAN) that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver air bag. On X5 and X6 vehicles, only the inflator will be replaced. All repairs will be performed free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.
Jun 19, 2019
BMW of North America, LLC (BMW) is recalling certain 2009 328i and 328xi, 2009-2011 335d, 2008-2012 M3 Coupe and M3 Convertible, and 2008-2011 M3 Sedan vehicles. The connection of the positive battery cable at the fuse box terminal may degrade, resulting in an intermittent loss of electrical power.
Consequence & remedy
Consequence: A loss of electrical power can cause the vehicle to stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace and secure the positive battery cable connector, free of charge. The recall began August 14, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of a previous recall, number 18V-314.
Additional source detail variants (3)
Electrical System:wiring:fuses And Circuit Breakers
BMW of North America, LLC (BMW) is recalling certain 2009 328i and 328xi, 2009-2011 335d, 2008-2012 M3 Coupe and M3 Convertible, and 2008-2011 M3 Sedan vehicles. The connection of the positive battery cable at the fuse box terminal may degrade, resulting in an intermittent loss of electrical power.
Consequence: A loss of electrical power can cause the vehicle to stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace and secure the positive battery cable connector, free of charge. The recall began August 14, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of a previous recall, number 18V-314.
Electrical SYSTEM:12V/24V/48V Battery:cables
BMW of North America, LLC (BMW) is recalling certain 2009 328i and 328xi, 2009-2011 335d, 2008-2012 M3 Coupe and M3 Convertible, and 2008-2011 M3 Sedan vehicles. The connection of the positive battery cable at the fuse box terminal may degrade, resulting in an intermittent loss of electrical power.
Consequence: A loss of electrical power can cause the vehicle to stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace and secure the positive battery cable connector, free of charge. The recall began August 14, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of a previous recall, number 18V-314.
Electrical System
BMW of North America, LLC (BMW) is recalling certain 2009 328i and 328xi, 2009-2011 335d, 2008-2012 M3 Coupe and M3 Convertible, and 2008-2011 M3 Sedan vehicles. The connection of the positive battery cable at the fuse box terminal may degrade, resulting in an intermittent loss of electrical power.
Consequence: A loss of electrical power can cause the vehicle to stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace and secure the positive battery cable connector, free of charge. The recall began August 14, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of a previous recall, number 18V-314.
Oct 25, 2017
BMW of North America, LLC (BMW) is recalling certain 2006-2011 323i, 325i, 325xi, 328i, 328xi, 330i, 330xi, 335i, 335xi and M3, 2007-2011 328i xDrive, 335i xDrive and 335is and 2009-2011 335d vehicles. The wiring and electrical connectors for the system that controls air flow for the heating and air conditioning system may overheat.
Consequence & remedy
Consequence: Wiring that overheats could cause the electrical connectors to melt, and increase the risk of a fire, even when the vehicle is unattended.
Remedy: BMW will notify owners, and dealers will replace the wiring and electrical connectors, free of charge. Interim letters were mailed on November 27, 2017. Owners will receive a second notice when the remedy becomes available. Owners may contact BMW customer service at 1-800-525-7417.
Feb 5, 2016
BMW of North America, LLC (BMW) is recalling certain model year 2008-2013 128i and 135i coupes and convertibles and 1 Series M coupes, 2006-2011 325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi, 335i, 335xi, 335i xDrive Sedans, 2009-2011 335d sedans, 2006-2012 325xiT, 328i and 328xi sports wagons, 2007-2013 328i, 328xi, 328i xDrive, 335i, 335xi, 335i xDrive, 335is and M3 Coupes and Convertibles, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i SAVs, 2007-2010 X3 xDrive30i SAVs, 2007-2013 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5 M SAVs, 2009-2013 BMW X5 xDrive35d SAVs, 2008-2014 X6 xDrive35i, X6 xDrive50i, and X6 M SACs, 2010-2011 BMW X6 xDrive50i SACs and 2008-2011 M3 Sedan vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's frontal air bag module or inflator depending on the vehicle model, free of charge. The recall began March 9, 2018. Owners may contact BMW customer service at 1-800-525-7417.
Nov 14, 2008
BMW IS RECALLING 2,500 MY 2008-2009 M3 PASSENGER VEHICLES WITH AN OPTIONAL DOUBLE CLUTCH TRANSMISSION. THE PROBLEM INVOLVES THE DOUBLE CLUTCH GEARBOX. IN A SITUATION OF RAPID VEHICLE DECELERATION, THE TRANSMISSION SOFTWARE MAY PERFORM A MULTISTAGE DOWNSHIFT.
Consequence & remedy
Consequence: IN THAT SITUATION, AT LOW VEHICLE SPEEDS, IT IS POSSIBLE FOR THE ENGINE TO STALL INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL REPROGRAM THE ENGINE AND TRANSMISSION ELECTRONIC CONTROL UNIT WITH UPDATED SOFTWARE FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 3, 2008. OWNERS MAY CONTACT BMW AT 1-800-831-1117.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration