← New search

2003 BMW 745LI

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2003 BMW 745LI do not stand out strongly from the model-year median of 25.

About this comparison →

When problems were reported

Mileage at the reported incident

37 reports with mileage · 13 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 11 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Power Train. Review the 8 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 7 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

1 crash reports0 fire reports1 injury reports

Vehicle Speed Control complaints

5 reports
Clear category filter
Mileage unknown · Feb 29, 2016
Air BagsVehicle Speed ControlCrashInjury

TL* THE CONTACT OWNS A 2003 BMW 745LI. WHILE ATTEMPTING TO STOP THE VEHICLE WITH THE BRAKE PEDAL DEPRESSED, THE VEHICLE INDEPENDENTLY ACCELERATED. AS A RESULT, THE CONTACT CRASHED INTO THE DRIVER SIDE OF ANOTHER VEHICLE AND THEN INTO A BUILDING. THE AIR BAGS FAILED TO DEPLOY. THE CONTACT SUSTAINED LEG, BACK, AND NECK INJURIES TH…

Read full complaint

TL* THE CONTACT OWNS A 2003 BMW 745LI. WHILE ATTEMPTING TO STOP THE VEHICLE WITH THE BRAKE PEDAL DEPRESSED, THE VEHICLE INDEPENDENTLY ACCELERATED. AS A RESULT, THE CONTACT CRASHED INTO THE DRIVER SIDE OF ANOTHER VEHICLE AND THEN INTO A BUILDING. THE AIR BAGS FAILED TO DEPLOY. THE CONTACT SUSTAINED LEG, BACK, AND NECK INJURIES THAT REQUIRED MEDICAL ATTENTION. A POLICE REPORT WAS FILED. THE VEHICLE WAS TOWED FROM THE CRASH SCENE TO A DEALER WHO WAS UNABLE TO DIAGNOSE OR REPAIR THE VEHICLE. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS UNKNOWN.

NHTSA ODI #10838894

143,000 miles · Aug 16, 2012
EnginePower TrainVehicle Speed Control

TERRIBLE TRANSMISSION IN THIS CAR!!!WHILE DRIVING, THIS CAR JUMPS INTO GEAR. FEELS LIKE SOMEONE HIT ME FROM BEHIND WHENEVER I STOP. IT ALSO STARTED LEAKING TRANSMISSION FLUID. AFTER RESEARCHING THIS CAR, I HAVE FOUND OUT THE 745LI MODELS ARE KNOWN FOR TRANSMISSION PROBLEMS,AND LEAKS. THIS CAR SHOULD HAVE A RECALL ON IT,BECAUSE …

Read full complaint

TERRIBLE TRANSMISSION IN THIS CAR!!!WHILE DRIVING, THIS CAR JUMPS INTO GEAR. FEELS LIKE SOMEONE HIT ME FROM BEHIND WHENEVER I STOP. IT ALSO STARTED LEAKING TRANSMISSION FLUID. AFTER RESEARCHING THIS CAR, I HAVE FOUND OUT THE 745LI MODELS ARE KNOWN FOR TRANSMISSION PROBLEMS,AND LEAKS. THIS CAR SHOULD HAVE A RECALL ON IT,BECAUSE APPARENTLY BMW KNOWS THIS,AND HAS DONE NOTHING ABOUT IT. THEY SHOULD MAKE CONSUMERS AWARE THEY HAVE ONGOING PROBLEMS WITH THE TRANSMISSIONS. I WENT TO DROP CAR OFF FOR REPAIR,AND THERE WERE 4 OTHER 745LI'S NEEDING SAME REPAIR. BMW SHOULD BE MADE TO RECALL THESE CARS,AND PAY TO HAVE THEM REPAIRED,OR REIMBURSE US IF WE ALREADY HAD THIS FIXED. *TR

NHTSA ODI #10470881

109,606 miles · Aug 8, 2011
Engine And Engine CoolingVehicle Speed Control

11/09 DRIVERSIDE WINDOW REGULATOR REPLACED;CONSTANTLY REPLACING DRIVER SIDE TURN SIGNAL BULB; IN APPROX. MARCH 2010 CAR WOULD RANDOMLY NOT GO INTO REVERSE AND WHEN I WAS ABLE TO GET IT INTO DRIVE CAR WOULD FEEL SLUGGISH OR WHEN COMING TO A STOP FELT AS IF I WAS HIT FROM BEHIND OR CAR WOULD GO INTO FAILSAFE MODE AND I WOULD BE UN…

Read full complaint

11/09 DRIVERSIDE WINDOW REGULATOR REPLACED;CONSTANTLY REPLACING DRIVER SIDE TURN SIGNAL BULB; IN APPROX. MARCH 2010 CAR WOULD RANDOMLY NOT GO INTO REVERSE AND WHEN I WAS ABLE TO GET IT INTO DRIVE CAR WOULD FEEL SLUGGISH OR WHEN COMING TO A STOP FELT AS IF I WAS HIT FROM BEHIND OR CAR WOULD GO INTO FAILSAFE MODE AND I WOULD BE UNABLE TO ACCELERATE, HAD DIAGNOSED BY BMW WAS TOLD 10K+ TO HAVE TRANNY REPLACED ; FOUND A REBUILT TRANNY AND REPLACED IN APPROX. MAY 2010; HERE WE ARE IN AUGUST 2011 AND CAR AGAIN BEGAN TO NOT GO INTO REVERSE AND GIVE A FAILSAFE NOTIFICATION; ATTEMPTED TO START CAR TODAY 8/8 TO TAKE TO SHOP; HOWEVER CAR WOULD NOT GO INTO REVERSE AND WHEN IT FINALLY INDICATED IT WAS IN REVERSE; ACTUALLY WENT FORWARD BEGAN TO MAKE A WEIRD GRINDING NOISE SO I TURNED IT OFF AND THERE IT SITS IN MY DRIVEWAY LEAKING WHAT I PRESUME TO BE TRANSMISSION FLUID UNABLE TO BE DRIVEN. CURRENT MILEAGE 133K

NHTSA ODI #10418836

Mileage unknown · Dec 11, 2003
Vehicle Speed Control

WHILE WAITING AT AN INTERSECTION VEHICLE SUDDENLY ACCELERATED. CONSUMER WAS ABLE TO MAINTAIN CONTROL OF THE VEHICLE, AND DROVE THE VEHICLE TO DEALER FOR ANALYSIS. MECHANIC TOLD CONSUMER THAT THIS WAS A DESIGN DEFECT, AND COULD NOT RESOLVE THE PROBLEM. *AK

NHTSA ODI #10050445

Mileage unknown · Dec 11, 2003
Electronic Stability ControlVehicle Speed Control

REPETITIVE PROBLEMS WITH NAVIGATION, PHONE-- IDLING ISSUES THAT CAR VEHICLE TO SPUTTER AND OR LURCH FORWARD STABILITY CONTROL THAT SWITCHES ITSELF OFF WHILE VEHICLE IN MOTION. AK

NHTSA ODI #10049581

Official recalls

2

03V324000 · Engine And Engine Cooling

Aug 26, 2003

ON CERTAIN PASSENGER VEHICLES, THE ENGINE OIL FILTER DRAIN PLUG MAY BE INSUFFICIENTLY TIGHTENED. THIS COULD LEAD TO LOOSENING OF THE PLUG CAUSING AN INITIAL OIL SPRAY AND A SUBSEQUENT OIL LEAK.

Consequence & remedy

Consequence: IF A LARGE AMOUNT OF OIL LOSS OCCURS, ENGINE DAMAGE MAY RESULT. DEPENDING ON THE EXTENT OF THE DAMAGE, A CRASH COULD OCCUR.

Remedy: DEALERS WILL INSPECT THE TORQUE OF THE OIL FILTER DRAIN PLUG AND, IF NECESSARY, RETIGHTEN THE DRAIN PLUG WITH THE CORRECTLY SPECIFIED TORQUE. OWNER NOTIFICATION BEGAN ON SEPTEMBER 12, 2003. OWNERS SHOULD CONTACT BMW AT 1-800-831-1117.

03V240000 · Engine And Engine Cooling

Jul 1, 2003

ON CERTAIN PASSENGER VEHICLES, DUE TO A SOFTWARE ERROR, A DESYNCHRONIZATION OF THE VALVETRONIC MOTORS FOR ENGINE BANKS I AND II MAY OCCUR. IF THIS OCCURS, THE ENGINE COULD STALL.

Consequence & remedy

Consequence: IN THOSE CASES, THE DRIVER MAY NOT BE ABLE TO RESTART THE ENGINE. DEPENDING ON THE LEVEL OF ENGINE ROUGHNESS, OR STALLING, AS WELL AS TRAFFIC CONDITIONS AND THE DRIVER'S REACTIONS, THIS COULD LEAD TO A CRASH.

Remedy: DEALERS WILL REPROGRAM THE DIGITAL ENGINE MANAGEMENT CONTROL UNIT. OWNER NOTIFICATION BEGAN JULY 8, 2003. OWNERS SHOULD CONTACT BMW AT 1-800-831-1117.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

EA12002 · Vehicle Rollaway

Opened Apr 10, 2012 · Closed Jan 24, 2013

Status: closed (inferred from source dates) · Electrical System; Electrical System:ignition; Electrical System:ignition:switch; Power Train:automatic Transmission

In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770

Additional source detail variants (4)

Electrical System

In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770

Electrical System:ignition

In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770

Electrical System:ignition:switch

In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770

Power Train:automatic Transmission

In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770

PE11025 · Vehicle Rollaway

Opened Aug 5, 2011 · Closed Apr 23, 2012

Status: closed (inferred from source dates) · Electrical System; Power Train:automatic Transmission

In response to the Office of Defects Investigation's (ODI) Information Request (IR) for PE11-025, BMW provided ODI with 1 complaint and 46 field reports relating to either incidents of unattended vehicle rollaway or vehicle movement after the driver expected the vehicle gearshift to automatically shift to park. ODI's analysis of the data provided by BMW identified 14 crashes and 5 alleged injuries. ODI has also identified 3 additional reports in its database alleging vehicle rollaway incidents of which 2 resulted in crashes.The subject vehicles are all equipped with push-buttons (Start/Stop button) to control starting/stopping the engine and Shift-by-Wire gearshift systems controlled by a column mounted selector lever behind the steering wheel. The Start/Stop button also controls switching the ignition and the radio ready state On and Off. Shift-by-wire systems replace the traditional mechanical connection (e.g., cable or linkage) between the gearshift and automatic transmission with an electronic connection controlled by a computer module. When parking the vehicle, the driver has the capability to manually shift the vehicle to park by pressing the Park button on the end of the electronic gearshift lever. However, the instructions for engine shutoff provided in the owner's manual state that pressing the Start/Stop button serves the dual function of switching off the engine and automatically shifting the transmission to Park.In response to ODI's information request for PE11-025, BMW described several circumstances where the subject vehicles may shift to neutral when the driver may expect it to automatically shift to park. First, for Comfort Access System (CAS) vehicles, if the transmission is in neutral when the key fob is in the ignition slot and the Start/Stop button is pressed to shut-off the engine, the transmission will remain in neutral. This is referred to as the Carwash mode and is a normal operating feature of the vehicles that is described in the owner's manual. BMW also described two circumstances that are not normal operating features and are not described in the owners' manual: (1) with the transmission in drive or reverse and the engine running, if the Start/Stop button is pushed 2 or 3 times within a 0.3 second to 0.5 second interval, the engine will stop and the transmission will shift to Neutral; and 2) if the Park button on the gearshift lever is pressed at the same time that the gearshift lever is actuated (i.e., toggled up or down) to select drive, reverse or neutral; the transmission will shift to neutral or remain in neutral.Beginning in model year (MY) 2005, BMW introduced CAS as an optional feature package for the subject vehicles.The key for CAS equipped vehicles is an electronic code that is sent to the engine control module by a remote transmitter (key fob). An optional docking port (key slot) is provided for driver convenience or to put the vehicle into Car Wash mode, which allows for engine shutoff in neutral. BMW sold approximately 45,000 subject vehicles with CAS and approximately 94 percent of the CAS equipped vehicles were produced from MY 2006 through 2008. Non-CAS subject vehicles were produced from MY 2002 through 2008 and require the remote control to be in the ignition slot located next to the Start/Stop button to start the engine.The 50 incidents identified by ODI's analysis of complaints and field reports include 18 involving CAS vehicles (39.6 incidents per 100,000 vehicles) and 32 involving non-CAS vehicles (42.0 incidents per 100,000 vehicles). Because the incidents are considered random events, the failure rates were also adjusted for vehicle exposure, resulting in rat

Additional source detail variants (2)

Electrical System

In response to the Office of Defects Investigation's (ODI) Information Request (IR) for PE11-025, BMW provided ODI with 1 complaint and 46 field reports relating to either incidents of unattended vehicle rollaway or vehicle movement after the driver expected the vehicle gearshift to automatically shift to park. ODI's analysis of the data provided by BMW identified 14 crashes and 5 alleged injuries. ODI has also identified 3 additional reports in its database alleging vehicle rollaway incidents of which 2 resulted in crashes.The subject vehicles are all equipped with push-buttons (Start/Stop button) to control starting/stopping the engine and Shift-by-Wire gearshift systems controlled by a column mounted selector lever behind the steering wheel. The Start/Stop button also controls switching the ignition and the radio ready state On and Off. Shift-by-wire systems replace the traditional mechanical connection (e.g., cable or linkage) between the gearshift and automatic transmission with an electronic connection controlled by a computer module. When parking the vehicle, the driver has the capability to manually shift the vehicle to park by pressing the Park button on the end of the electronic gearshift lever. However, the instructions for engine shutoff provided in the owner's manual state that pressing the Start/Stop button serves the dual function of switching off the engine and automatically shifting the transmission to Park.In response to ODI's information request for PE11-025, BMW described several circumstances where the subject vehicles may shift to neutral when the driver may expect it to automatically shift to park. First, for Comfort Access System (CAS) vehicles, if the transmission is in neutral when the key fob is in the ignition slot and the Start/Stop button is pressed to shut-off the engine, the transmission will remain in neutral. This is referred to as the Carwash mode and is a normal operating feature of the vehicles that is described in the owner's manual. BMW also described two circumstances that are not normal operating features and are not described in the owners' manual: (1) with the transmission in drive or reverse and the engine running, if the Start/Stop button is pushed 2 or 3 times within a 0.3 second to 0.5 second interval, the engine will stop and the transmission will shift to Neutral; and 2) if the Park button on the gearshift lever is pressed at the same time that the gearshift lever is actuated (i.e., toggled up or down) to select drive, reverse or neutral; the transmission will shift to neutral or remain in neutral.Beginning in model year (MY) 2005, BMW introduced CAS as an optional feature package for the subject vehicles.The key for CAS equipped vehicles is an electronic code that is sent to the engine control module by a remote transmitter (key fob). An optional docking port (key slot) is provided for driver convenience or to put the vehicle into Car Wash mode, which allows for engine shutoff in neutral. BMW sold approximately 45,000 subject vehicles with CAS and approximately 94 percent of the CAS equipped vehicles were produced from MY 2006 through 2008. Non-CAS subject vehicles were produced from MY 2002 through 2008 and require the remote control to be in the ignition slot located next to the Start/Stop button to start the engine.The 50 incidents identified by ODI's analysis of complaints and field reports include 18 involving CAS vehicles (39.6 incidents per 100,000 vehicles) and 32 involving non-CAS vehicles (42.0 incidents per 100,000 vehicles). Because the incidents are considered random events, the failure rates were also adjusted for vehicle exposure, resulting in rat

Power Train:automatic Transmission

In response to the Office of Defects Investigation's (ODI) Information Request (IR) for PE11-025, BMW provided ODI with 1 complaint and 46 field reports relating to either incidents of unattended vehicle rollaway or vehicle movement after the driver expected the vehicle gearshift to automatically shift to park. ODI's analysis of the data provided by BMW identified 14 crashes and 5 alleged injuries. ODI has also identified 3 additional reports in its database alleging vehicle rollaway incidents of which 2 resulted in crashes.The subject vehicles are all equipped with push-buttons (Start/Stop button) to control starting/stopping the engine and Shift-by-Wire gearshift systems controlled by a column mounted selector lever behind the steering wheel. The Start/Stop button also controls switching the ignition and the radio ready state On and Off. Shift-by-wire systems replace the traditional mechanical connection (e.g., cable or linkage) between the gearshift and automatic transmission with an electronic connection controlled by a computer module. When parking the vehicle, the driver has the capability to manually shift the vehicle to park by pressing the Park button on the end of the electronic gearshift lever. However, the instructions for engine shutoff provided in the owner's manual state that pressing the Start/Stop button serves the dual function of switching off the engine and automatically shifting the transmission to Park.In response to ODI's information request for PE11-025, BMW described several circumstances where the subject vehicles may shift to neutral when the driver may expect it to automatically shift to park. First, for Comfort Access System (CAS) vehicles, if the transmission is in neutral when the key fob is in the ignition slot and the Start/Stop button is pressed to shut-off the engine, the transmission will remain in neutral. This is referred to as the Carwash mode and is a normal operating feature of the vehicles that is described in the owner's manual. BMW also described two circumstances that are not normal operating features and are not described in the owners' manual: (1) with the transmission in drive or reverse and the engine running, if the Start/Stop button is pushed 2 or 3 times within a 0.3 second to 0.5 second interval, the engine will stop and the transmission will shift to Neutral; and 2) if the Park button on the gearshift lever is pressed at the same time that the gearshift lever is actuated (i.e., toggled up or down) to select drive, reverse or neutral; the transmission will shift to neutral or remain in neutral.Beginning in model year (MY) 2005, BMW introduced CAS as an optional feature package for the subject vehicles.The key for CAS equipped vehicles is an electronic code that is sent to the engine control module by a remote transmitter (key fob). An optional docking port (key slot) is provided for driver convenience or to put the vehicle into Car Wash mode, which allows for engine shutoff in neutral. BMW sold approximately 45,000 subject vehicles with CAS and approximately 94 percent of the CAS equipped vehicles were produced from MY 2006 through 2008. Non-CAS subject vehicles were produced from MY 2002 through 2008 and require the remote control to be in the ignition slot located next to the Start/Stop button to start the engine.The 50 incidents identified by ODI's analysis of complaints and field reports include 18 involving CAS vehicles (39.6 incidents per 100,000 vehicles) and 32 involving non-CAS vehicles (42.0 incidents per 100,000 vehicles). Because the incidents are considered random events, the failure rates were also adjusted for vehicle exposure, resulting in rat