I JUST CAME ACROSS NHTSA ACTION NUMBER : PE11025 AND WANTED TO MAKE YOU AWARE OF THE FOLLOWING: I PARKED MY CAR IN FRONT OF MY DAUGHTER'S DAY CARE CENTER (THE GODDARD SCHOOL, SUWANEE) ON THE MONDAY BEFORE EASTER IN 2010 (MARCH 29, 2010). WHEN I CAME OUT, I DISCOVERED THE CAR APPROXIMATELY 40 YARDS AWAY CRASHED INTO THE EMBANKM…
Read full complaint
I JUST CAME ACROSS NHTSA ACTION NUMBER : PE11025 AND WANTED TO MAKE YOU AWARE OF THE FOLLOWING: I PARKED MY CAR IN FRONT OF MY DAUGHTER'S DAY CARE CENTER (THE GODDARD SCHOOL, SUWANEE) ON THE MONDAY BEFORE EASTER IN 2010 (MARCH 29, 2010). WHEN I CAME OUT, I DISCOVERED THE CAR APPROXIMATELY 40 YARDS AWAY CRASHED INTO THE EMBANKMENT OF THE NEIGHBORING PARKING LOT, AT AN INCLINE OF APPROXIMATELY 45 DEGREES. MY CAR WAS DAMAGED, AS WAS THE LANDSCAPING AT THE CRASH SITE, HOWEVER, NO ONE WAS INJURED. IN RESPONSE TO MY INQUIRY, BMW INDICATED THAT THERE WERE NO RECALLS RELATED TO ISSUES SUCH AS THE ONE I EXPERIENCED. THE REPAIR SHOP WAS BAFFLED BY THE ISSUE AS WELL AND SAID IT MIGHT BE ATTRIBUTABLE TO A FAULTY PARKING BRAKE ACTUATOR. THE VEHICLE STILL GIVES OCCASIONAL TRANSMISSION FAULT ERROR MESSAGES AND INDICATORS. I HAD TO FILE AN INSURANCE CLAIM AND CAN CONTACT THE COMPANY FOR DETAILS. I ALSO STILL HAVE PICTURES SOMEWHERE IF SOMEONE WOULD LIKE TO VIEW THEM. THE REPAIRS (MECHANICAL AND BODY WORK) WERE COMPLETED AT GODWIN AUTOMOTIVE IN DULUTH/JOHNS CREEK, GEORGIA. THE MILEAGE STATED ABOVE IS BASED ON MEMORY AND MY NOT BE ACCURATE. *KB
NHTSA ODI #10429922
Mileage unknown · Oct 9, 2011
Electrical SystemPower Train
TRANSMISSION GOES INTO NEUTRAL WHEN I PUSH BUTTON TO STOP CAR,ALSO LOGIC 7 SOUND IS A PROBLEM. *TR
NHTSA ODI #10429261
106,112 miles · Aug 30, 2011
Power Train
TL* THE CONTACT OWNS A 2002 BMW 745 LI. THE CONTACT STATED THAT WHILE REVERSING, THE GEAR SHIFTED INTO NEUTRAL INDEPENDENTLY. THE FAILURE WAS EXPERIENCED INTERMITTENTLY. THE VEHICLE WAS NOT TAKEN TO THE DEALER TO BE DIAGNOSED OR REPAIRED. THE FAILURE MILEAGE WAS 106,112 AND THE CURRENT MILEAGE WAS 106,313.
NHTSA ODI #10422543
106,234 miles · Aug 30, 2011
Power Train
WHEN CAR PUT IN REVERSE; TRANSMISSION GOES INTO NEUTRAL ABRUPTLY. TRANS IN NEUTRAL CODE APPEARS ON DASH. *TR
NHTSA ODI #10422538
Mileage unknown · Nov 3, 2009
Power Train
TRANSMISSION SLAMS HARD WHEN ACCELERATING FROM FIRST GEAR TO SECOND GEAR. *TR
NHTSA ODI #10290839
69,000 miles · Oct 22, 2009
Power Train
TRANSMISSION JERKS AND GOES TO NEUTRAL. SOMETIMES IT GOES INTO A FAILSAFE MODE AND ONCE THE CAR IS RESTARTED RETURNS TO NORMAL.*TR
NHTSA ODI #10289392
Mileage unknown · Apr 10, 2003
Air BagsEquipmentPower Train
NAR 04/10/2003 THE CONSUMERS HAS EXPERIENCED NUMEROUS PROBLEMS WITH THERE VEHICLE. THE TRANSMISSION HAS CAUSED THE VEHICLE TO SKID TO A STOP WHEN ACCELERATING ON THE BRAKE, THE PASSENGER AIR BAGS LIGHT COMES ON FOR NO REASON, AND THE COMPUTER SYSTEM THAT CONTROL THE VEHICLE AND ALLOWS IT TO FUNCTION HAS BEEN REPAIRED AND REPROG…
Read full complaint
NAR 04/10/2003 THE CONSUMERS HAS EXPERIENCED NUMEROUS PROBLEMS WITH THERE VEHICLE. THE TRANSMISSION HAS CAUSED THE VEHICLE TO SKID TO A STOP WHEN ACCELERATING ON THE BRAKE, THE PASSENGER AIR BAGS LIGHT COMES ON FOR NO REASON, AND THE COMPUTER SYSTEM THAT CONTROL THE VEHICLE AND ALLOWS IT TO FUNCTION HAS BEEN REPAIRED AND REPROGRAMMED 3 SEPARATE OCCASIONS. THE CONSUMER IS REQUESTING IMMEDIATE ASSISTANCE IN RESOLVING THIS SITUATION. *CB
NHTSA ODI #10015661
Mileage unknown · Dec 27, 2002
Power TrainSteering
2002 BMW 745LI HIGH PITCH WHINE FROM TRANSMISSION, SIMILAR TO AIRCRAFT TURBINE ENGINE NOISE, WHILE DRIVING AT HIGHWAY SPEEDS. BMW, IT'S DEALER AND HEADQUARTERS HAVE KNOWN ABOUT THIS PROBLEM AND ARE UNABLE TO RESOLVE OR FIX IT. ADDITIONAL PROBLEM WITH THIS VEHICLE IS A SHIMMY FROM THE FRONT END OF THE VEHICLE.
ON CERTAIN PASSENGER VEHICLES, DUE TO A SOFTWARE ERROR, A DESYNCHRONIZATION OF THE VALVETRONIC MOTORS FOR ENGINE BANKS I AND II MAY OCCUR. IF THIS OCCURS, THE ENGINE COULD STALL.
Consequence & remedy
Consequence: IN THOSE CASES, THE DRIVER MAY NOT BE ABLE TO RESTART THE ENGINE. DEPENDING ON THE LEVEL OF ENGINE ROUGHNESS, OR STALLING, AS WELL AS TRAFFIC CONDITIONS AND THE DRIVER'S REACTIONS, THIS COULD LEAD TO A CRASH.
Remedy: DEALERS WILL REPROGRAM THE DIGITAL ENGINE MANAGEMENT CONTROL UNIT. OWNER NOTIFICATION BEGAN JULY 8, 2003. OWNERS SHOULD CONTACT BMW AT 1-800-831-1117.
ON CERTAIN PASSENGER VEHICLES, THE ELECTRIC FUEL PUMP RUNS AT A ROTATIONAL SPEED THAT COULD RESULT IN REDUCED LUBRICATION OF ITS INTERNAL COMPONENTS. OVER AN EXTENDED PERIOD OF TIME, WEAR-INDUCED INTERNAL DAMAGE TO THE FUEL PUMP COULD RESULT IN INSUFFICIENT FUEL SUPPLY TO THE ENGINE WHEN THE FUEL TANK CONTAINS ONE-THIRD OR LESS OF ITS MAXIMUM FUEL CAPACITY.
Consequence & remedy
Consequence: IF THIS WERE TO OCCUR, THE ENGINE COULD STALL AND NOT BE RESTARTED UNTIL MORE FUEL WAS ADDED TO THE FUEL TANK. THIS COULD OCCUR EVEN THOUGH THE FUEL GAUGE INDICATED THAT FUEL STILL REMAINED IN THE TANK.
Remedy: DEALERS WILL REPROGRAM THE FUEL PUMP CONTROL SYSTEM. OWNER NOTIFICATION BEGAN JUNE 28, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-332-4269.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2
EA12002 · Vehicle Rollaway
Opened Apr 10, 2012 · Closed Jan 24, 2013
Status: closed (inferred from source dates) · Electrical System; Electrical System:ignition; Electrical System:ignition:switch; Power Train:automatic Transmission
In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770
Additional source detail variants (4)
Electrical System
In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770
Electrical System:ignition
In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770
Electrical System:ignition:switch
In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770
Power Train:automatic Transmission
In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770
PE11025 · Vehicle Rollaway
Opened Aug 5, 2011 · Closed Apr 23, 2012
Status: closed (inferred from source dates) · Electrical System; Power Train:automatic Transmission
In response to the Office of Defects Investigation's (ODI) Information Request (IR) for PE11-025, BMW provided ODI with 1 complaint and 46 field reports relating to either incidents of unattended vehicle rollaway or vehicle movement after the driver expected the vehicle gearshift to automatically shift to park. ODI's analysis of the data provided by BMW identified 14 crashes and 5 alleged injuries. ODI has also identified 3 additional reports in its database alleging vehicle rollaway incidents of which 2 resulted in crashes.The subject vehicles are all equipped with push-buttons (Start/Stop button) to control starting/stopping the engine and Shift-by-Wire gearshift systems controlled by a column mounted selector lever behind the steering wheel. The Start/Stop button also controls switching the ignition and the radio ready state On and Off. Shift-by-wire systems replace the traditional mechanical connection (e.g., cable or linkage) between the gearshift and automatic transmission with an electronic connection controlled by a computer module. When parking the vehicle, the driver has the capability to manually shift the vehicle to park by pressing the Park button on the end of the electronic gearshift lever. However, the instructions for engine shutoff provided in the owner's manual state that pressing the Start/Stop button serves the dual function of switching off the engine and automatically shifting the transmission to Park.In response to ODI's information request for PE11-025, BMW described several circumstances where the subject vehicles may shift to neutral when the driver may expect it to automatically shift to park. First, for Comfort Access System (CAS) vehicles, if the transmission is in neutral when the key fob is in the ignition slot and the Start/Stop button is pressed to shut-off the engine, the transmission will remain in neutral. This is referred to as the Carwash mode and is a normal operating feature of the vehicles that is described in the owner's manual. BMW also described two circumstances that are not normal operating features and are not described in the owners' manual: (1) with the transmission in drive or reverse and the engine running, if the Start/Stop button is pushed 2 or 3 times within a 0.3 second to 0.5 second interval, the engine will stop and the transmission will shift to Neutral; and 2) if the Park button on the gearshift lever is pressed at the same time that the gearshift lever is actuated (i.e., toggled up or down) to select drive, reverse or neutral; the transmission will shift to neutral or remain in neutral.Beginning in model year (MY) 2005, BMW introduced CAS as an optional feature package for the subject vehicles.The key for CAS equipped vehicles is an electronic code that is sent to the engine control module by a remote transmitter (key fob). An optional docking port (key slot) is provided for driver convenience or to put the vehicle into Car Wash mode, which allows for engine shutoff in neutral. BMW sold approximately 45,000 subject vehicles with CAS and approximately 94 percent of the CAS equipped vehicles were produced from MY 2006 through 2008. Non-CAS subject vehicles were produced from MY 2002 through 2008 and require the remote control to be in the ignition slot located next to the Start/Stop button to start the engine.The 50 incidents identified by ODI's analysis of complaints and field reports include 18 involving CAS vehicles (39.6 incidents per 100,000 vehicles) and 32 involving non-CAS vehicles (42.0 incidents per 100,000 vehicles). Because the incidents are considered random events, the failure rates were also adjusted for vehicle exposure, resulting in rat
Additional source detail variants (2)
Electrical System
In response to the Office of Defects Investigation's (ODI) Information Request (IR) for PE11-025, BMW provided ODI with 1 complaint and 46 field reports relating to either incidents of unattended vehicle rollaway or vehicle movement after the driver expected the vehicle gearshift to automatically shift to park. ODI's analysis of the data provided by BMW identified 14 crashes and 5 alleged injuries. ODI has also identified 3 additional reports in its database alleging vehicle rollaway incidents of which 2 resulted in crashes.The subject vehicles are all equipped with push-buttons (Start/Stop button) to control starting/stopping the engine and Shift-by-Wire gearshift systems controlled by a column mounted selector lever behind the steering wheel. The Start/Stop button also controls switching the ignition and the radio ready state On and Off. Shift-by-wire systems replace the traditional mechanical connection (e.g., cable or linkage) between the gearshift and automatic transmission with an electronic connection controlled by a computer module. When parking the vehicle, the driver has the capability to manually shift the vehicle to park by pressing the Park button on the end of the electronic gearshift lever. However, the instructions for engine shutoff provided in the owner's manual state that pressing the Start/Stop button serves the dual function of switching off the engine and automatically shifting the transmission to Park.In response to ODI's information request for PE11-025, BMW described several circumstances where the subject vehicles may shift to neutral when the driver may expect it to automatically shift to park. First, for Comfort Access System (CAS) vehicles, if the transmission is in neutral when the key fob is in the ignition slot and the Start/Stop button is pressed to shut-off the engine, the transmission will remain in neutral. This is referred to as the Carwash mode and is a normal operating feature of the vehicles that is described in the owner's manual. BMW also described two circumstances that are not normal operating features and are not described in the owners' manual: (1) with the transmission in drive or reverse and the engine running, if the Start/Stop button is pushed 2 or 3 times within a 0.3 second to 0.5 second interval, the engine will stop and the transmission will shift to Neutral; and 2) if the Park button on the gearshift lever is pressed at the same time that the gearshift lever is actuated (i.e., toggled up or down) to select drive, reverse or neutral; the transmission will shift to neutral or remain in neutral.Beginning in model year (MY) 2005, BMW introduced CAS as an optional feature package for the subject vehicles.The key for CAS equipped vehicles is an electronic code that is sent to the engine control module by a remote transmitter (key fob). An optional docking port (key slot) is provided for driver convenience or to put the vehicle into Car Wash mode, which allows for engine shutoff in neutral. BMW sold approximately 45,000 subject vehicles with CAS and approximately 94 percent of the CAS equipped vehicles were produced from MY 2006 through 2008. Non-CAS subject vehicles were produced from MY 2002 through 2008 and require the remote control to be in the ignition slot located next to the Start/Stop button to start the engine.The 50 incidents identified by ODI's analysis of complaints and field reports include 18 involving CAS vehicles (39.6 incidents per 100,000 vehicles) and 32 involving non-CAS vehicles (42.0 incidents per 100,000 vehicles). Because the incidents are considered random events, the failure rates were also adjusted for vehicle exposure, resulting in rat
Power Train:automatic Transmission
In response to the Office of Defects Investigation's (ODI) Information Request (IR) for PE11-025, BMW provided ODI with 1 complaint and 46 field reports relating to either incidents of unattended vehicle rollaway or vehicle movement after the driver expected the vehicle gearshift to automatically shift to park. ODI's analysis of the data provided by BMW identified 14 crashes and 5 alleged injuries. ODI has also identified 3 additional reports in its database alleging vehicle rollaway incidents of which 2 resulted in crashes.The subject vehicles are all equipped with push-buttons (Start/Stop button) to control starting/stopping the engine and Shift-by-Wire gearshift systems controlled by a column mounted selector lever behind the steering wheel. The Start/Stop button also controls switching the ignition and the radio ready state On and Off. Shift-by-wire systems replace the traditional mechanical connection (e.g., cable or linkage) between the gearshift and automatic transmission with an electronic connection controlled by a computer module. When parking the vehicle, the driver has the capability to manually shift the vehicle to park by pressing the Park button on the end of the electronic gearshift lever. However, the instructions for engine shutoff provided in the owner's manual state that pressing the Start/Stop button serves the dual function of switching off the engine and automatically shifting the transmission to Park.In response to ODI's information request for PE11-025, BMW described several circumstances where the subject vehicles may shift to neutral when the driver may expect it to automatically shift to park. First, for Comfort Access System (CAS) vehicles, if the transmission is in neutral when the key fob is in the ignition slot and the Start/Stop button is pressed to shut-off the engine, the transmission will remain in neutral. This is referred to as the Carwash mode and is a normal operating feature of the vehicles that is described in the owner's manual. BMW also described two circumstances that are not normal operating features and are not described in the owners' manual: (1) with the transmission in drive or reverse and the engine running, if the Start/Stop button is pushed 2 or 3 times within a 0.3 second to 0.5 second interval, the engine will stop and the transmission will shift to Neutral; and 2) if the Park button on the gearshift lever is pressed at the same time that the gearshift lever is actuated (i.e., toggled up or down) to select drive, reverse or neutral; the transmission will shift to neutral or remain in neutral.Beginning in model year (MY) 2005, BMW introduced CAS as an optional feature package for the subject vehicles.The key for CAS equipped vehicles is an electronic code that is sent to the engine control module by a remote transmitter (key fob). An optional docking port (key slot) is provided for driver convenience or to put the vehicle into Car Wash mode, which allows for engine shutoff in neutral. BMW sold approximately 45,000 subject vehicles with CAS and approximately 94 percent of the CAS equipped vehicles were produced from MY 2006 through 2008. Non-CAS subject vehicles were produced from MY 2002 through 2008 and require the remote control to be in the ignition slot located next to the Start/Stop button to start the engine.The 50 incidents identified by ODI's analysis of complaints and field reports include 18 involving CAS vehicles (39.6 incidents per 100,000 vehicles) and 32 involving non-CAS vehicles (42.0 incidents per 100,000 vehicles). Because the incidents are considered random events, the failure rates were also adjusted for vehicle exposure, resulting in rat
2002 BMW 745LI Problems, Complaints & Recalls | Skip That Year
Illustration