Vehicle: 2016 BMW 528i xDrive (VIN: [XXX]) Safety Issue / Defect Description: Strong, hazardous raw gasoline fumes began entering the passenger cabin and trunk area. On XXX, the vehicle was brought to an authorized dealership (BMW of Sterling) for diagnostic evaluation. The dealership's technician conducted a multi-point inspe…
Read full complaint
Vehicle: 2016 BMW 528i xDrive (VIN: [XXX]) Safety Issue / Defect Description: Strong, hazardous raw gasoline fumes began entering the passenger cabin and trunk area. On XXX, the vehicle was brought to an authorized dealership (BMW of Sterling) for diagnostic evaluation. The dealership's technician conducted a multi-point inspection and produced video evidence documenting fluid leaking from the top of the plastic fuel tank. The dealership issued Repair Order Quote #$4,824.92 to "REPLACE FUEL TANK DUE TO FUEL LEAK" and declared the vehicle unsafe. Despite diagnosing a structural fuel tank leak that allows raw gasoline and fumes to migrate into the cabin—presenting an immediate fire, explosion, and toxic vapor risk—BMW of North America and the dealership have refused warranty coverage or goodwill assistance, claiming the tank is "not leaking actively enough" under Service Bulletin SI B01 03 22 (NHTSA ID: MC-10212779-9999). An uncontained raw fuel leak on a plastic fuel tank is a critical safety defect that requires immediate investigation. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11753570
Mileage unknown · Jul 20, 2026
Fuel/propulsion System
The vehicle developed a strong, toxic odor of raw gasoline inside the passenger cabin and trunk area. The vehicle was brought to an authorized franchise, BMW of Sterling, where technicians performed a multi-point inspection. The technician confirmed that the factory plastic fuel tank assembly is structurally defective and leakin…
Read full complaint
The vehicle developed a strong, toxic odor of raw gasoline inside the passenger cabin and trunk area. The vehicle was brought to an authorized franchise, BMW of Sterling, where technicians performed a multi-point inspection. The technician confirmed that the factory plastic fuel tank assembly is structurally defective and leaking raw fuel from the top weld seams. The dealer provided an official invoice quoting $4,824.92 to replace the tank due to the fuel leak, noting it is an active hazard, but refused to cover the failure under BMW’s active 15-year/150,000-mile extended warranty for N20 plastic fuel tanks (SI B01 03 22). Driving a vehicle with raw fuel pooling on the exterior of the tank and migrating into the cabin creates an immediate fire hazard and health risk to occupants."
NHTSA ODI #11751663
Mileage unknown · Apr 21, 2025
EngineFuel/propulsion System
Concern- smoke coming out of back exhaust at start up Cause - TAYLOR BMW (dealership) - possible needs updated oil line, turbo may be leaking internally Correction- dealership pulled faults to see if cat efficiency faults were present, saw none. Did verify smoke on startup. Doesn’t look like the turbo oil feed line has been cha…
Read full complaint
Concern- smoke coming out of back exhaust at start up Cause - TAYLOR BMW (dealership) - possible needs updated oil line, turbo may be leaking internally Correction- dealership pulled faults to see if cat efficiency faults were present, saw none. Did verify smoke on startup. Doesn’t look like the turbo oil feed line has been changed (updated with check valve). There is some oil encrusted on the body of turbo. Would replace all lines since turbo removal is required for any of them; however once cat is off and if the chamber inside is wet with oil, at that point it would need a turbo as well as the lines. The above is the written diagnosis from dealership and I was quoted a price ranging from $2600- 4600- In 2016, NHTSA issued a notice for certain models/ years regarding the turbocharger feed lines (extending warranty for that part to 10 years / 120k miles). My 2016 was CPO and has only 84k (all maintenance performed by BMW) and I believe it should fall under eligible vehicles. I have reached out to BMW customer care, spoken with a case manager , all to no avail.
NHTSA ODI #11655918
Mileage unknown · Feb 19, 2025
Electrical SystemEngineFuel/propulsion System
Leak error messages that cannot be removed until recall issue with fluid leak is fixed. Leak is corroding engine fuel lines and can cause a fire Will driving. The remedy is taking to long to be deployed. Need assistance with this issue.
NHTSA ODI #11643709
35,000 miles · Sep 26, 2020
Fuel/propulsion System
BMW 528I 2016 CAR THAT IS LITTLE OVER 4 YEARS LESS JUST HIT 35K MILEAGE LOST ALL ITS FUEL INJECTORS, COILS AND PLUGS. BELOW IS THE SUMMARY OF DIAGNOSIS. 35146 FUEL INJECTORS FAULTY. CONFIRMED SES LIGHT IS ON. DME STORED SOURCED FROM THE VEHICLE MISFIRE FAULTS ON MULTIPLE CYLINDERS. DME ALSO STORED FAULT 118002 "MIXTU…
Read full complaint
BMW 528I 2016 CAR THAT IS LITTLE OVER 4 YEARS LESS JUST HIT 35K MILEAGE LOST ALL ITS FUEL INJECTORS, COILS AND PLUGS. BELOW IS THE SUMMARY OF DIAGNOSIS. 35146 FUEL INJECTORS FAULTY. CONFIRMED SES LIGHT IS ON. DME STORED SOURCED FROM THE VEHICLE MISFIRE FAULTS ON MULTIPLE CYLINDERS. DME ALSO STORED FAULT 118002 "MIXTURE TOO RICH," WORKED THROUGH TEST PLAN. PERFORMED ENGINE TEST AND MANUFACTURER AND BACKED BY DETERMINED CYLINDERS 1, 2, AND 4 INJECTORS FAULTY. DIAGCODE: ITS LIMITED WARRANTY. D1350 00000000 01 002. REMOVED ALL SPARK PLUGS AND FOUND SPARK PLUGS 2, 3, AND 4 FUEL SOAKED. RECOMMEND REPLACE ALL 4 FUEL INJECTORS AND SPARK PLUGS. ALSO RECOMMEND REPLACE ALL 4 IGNITION COILS AS A PREVENTATIVE TOTAL COST ESTIMATED IS AROUND $4500; BMW NORTH AMERICA IS NOT ACKNOWLEDGED THERE IS AN ISSUE WITH CAR OR MODEL
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Engine And Engine Cooling:cooling System:pump
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2017 BMW 640i, 640i xDrive, 650i, 650i xDrive, M6, 535i, 535i xDrive, 430i, 430i xDrive, 440i, 440i xDrive, M4, X1 sDrive28i, X1 xDrive28i, i3, i8, Rolls-Royce Dawn, Mini Clubman Cooper, Clubman Cooper S, Cooper All4, Cooper S All4, Mini 4-Door Cooper, Cooper S, Mini 2-Door Cooper, Cooper S, John Cooper Works and 2016 BMW 528i, 528i xDrive, 535i, 535i xDrive, 550i, 550i xDrive, M5 and 535d vehicles. The affected vehicles have seat- mounted side air bag inflator initiators that may fail to ignite during a crash.
Consequence & remedy
Consequence: If the air bag inflator initiator fails to ignite, the seat-mounted air bag will not deploy, increasing the risk of injury.
Remedy: BMW will notify owners, and dealers will replace the air bag modules, free of charge. The recall began February 6, 2017. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2016-2017 X1 sDrive28i, X1 xDrive28i, MINI Hardtop 4 Door Cooper, Mini Hardtop 4 Door Cooper S, MINI Cooper Clubman, and Cooper S Clubman, 2017 Rolls-Royce Ghost, and 2016 528i vehicles. The vehicle-sensitive locking mechanism of the seat belt Emergency Locking Retractor (ELR) for the driver's seat may not lock as designed. As such, these vehicles fail to comply with the requirements of the Federal Motor Vehicle Safety Standard (FMVSS) number 209, "Seat Belt Assemblies."
Consequence & remedy
Consequence: In the event of a crash where heavy braking is applied, the Emergency Locking Retractor (ELR) may activate when the occupant is more forward in the seat, possibly increasing the risk of injury.
Remedy: BMW will notify owners, and dealers will replace the driver's seat belt assembly, free of charge. The recall began July 3, 2019. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2016 528i, 528i xDrive, 535i, 535i xDrive, 535d xDrive, M5, 550i, 550i xDrive, and 535d sedans. The affected vehicles have an inboard lower anchor for child restraints on the left rear seat that may have been bent downwards, preventing the child seat from fully engaging both lower anchors. As such, these vehicles may fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 225, "Child Restraint Anchorage Systems."
Consequence & remedy
Consequence: If the child seat is not properly attached to the lower anchors, it can increase the child's risk of injury in the event of a crash.
Remedy: BMW will notify owners, and dealers will inspect and, if necessary, repair the inboard lower anchor on the left rear seat, free of charge. The recall began on December 28, 2015. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Child Seat
BMW of North America, LLC (BMW) is recalling certain model year 2016 528i, 528i xDrive, 535i, 535i xDrive, 535d xDrive, M5, 550i, 550i xDrive, and 535d sedans. The affected vehicles have an inboard lower anchor for child restraints on the left rear seat that may have been bent downwards, preventing the child seat from fully engaging both lower anchors. As such, these vehicles may fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 225, "Child Restraint Anchorage Systems."
Consequence: If the child seat is not properly attached to the lower anchors, it can increase the child's risk of injury in the event of a crash.
Remedy: BMW will notify owners, and dealers will inspect and, if necessary, repair the inboard lower anchor on the left rear seat, free of charge. The recall began on December 28, 2015. Owners may contact BMW customer service at 1-800-525-7417.
Seats:mid/rear Assembly
BMW of North America, LLC (BMW) is recalling certain model year 2016 528i, 528i xDrive, 535i, 535i xDrive, 535d xDrive, M5, 550i, 550i xDrive, and 535d sedans. The affected vehicles have an inboard lower anchor for child restraints on the left rear seat that may have been bent downwards, preventing the child seat from fully engaging both lower anchors. As such, these vehicles may fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 225, "Child Restraint Anchorage Systems."
Consequence: If the child seat is not properly attached to the lower anchors, it can increase the child's risk of injury in the event of a crash.
Remedy: BMW will notify owners, and dealers will inspect and, if necessary, repair the inboard lower anchor on the left rear seat, free of charge. The recall began on December 28, 2015. Owners may contact BMW customer service at 1-800-525-7417.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
2016 BMW 528I Problems, Complaints & Recalls | Skip That Year
Illustration