NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
21 reports131,992 miles · Jul 28, 2026
Visibility
The contact owns a 2019 BMW 430I. The contact stated that while driving approximately 55 MPH and switching lanes, there was a loud explosion. The contact was unable to determine the cause of the sound. The contact pulled over to the side of the road to inspect the tires and discovered that the sunroof had shattered upward. The d…
Read full complaint
The contact owns a 2019 BMW 430I. The contact stated that while driving approximately 55 MPH and switching lanes, there was a loud explosion. The contact was unable to determine the cause of the sound. The contact pulled over to the side of the road to inspect the tires and discovered that the sunroof had shattered upward. The dealer was notified of the failure. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 131,992.
NHTSA ODI #11753237
Mileage unknown · Jun 17, 2026
EngineFuel/propulsion System
The car has a plastic part in the oil housing component that cracks under heat usually between 50000 and 70000 miles causing a major loss of coolant onto highway and disables the engine
NHTSA ODI #11744815
116,758 miles · Feb 6, 2026
Engine And Engine Cooling
The contact owns a 2019 BMW 430I. The contact stated that there was a coolant leak. The contact stated that the engine overheated and the vehicle stalled while driving. The message "Engine Overheating - Stop Vehicle Immediately" was displayed. The vehicle was towed to the local dealer, where it was diagnosed, and it was determin…
Read full complaint
The contact owns a 2019 BMW 430I. The contact stated that there was a coolant leak. The contact stated that the engine overheated and the vehicle stalled while driving. The message "Engine Overheating - Stop Vehicle Immediately" was displayed. The vehicle was towed to the local dealer, where it was diagnosed, and it was determined that the coolant housing needed to be replaced. The vehicle was repaired, but the failure recurred. The vehicle was taken back to the local dealer, where it was determined that the coolant water pump needed to be replaced. The vehicle was repaired, but the failure persisted. The vehicle was taken to the same local dealer, where it was diagnosed, and it was determined that there was coolant leaking from the oil housing. The vehicle was not repaired. The manufacturer was contacted, a complaint was filed, and the contact was referred to the NHTSA Hotline. The failure mileage was approximately 116,758.
NHTSA ODI #11716146
Mileage unknown · Dec 3, 2025
Air BagsSeat BeltsUnknown Or Other
I am reporting a potential safety defect involving the seatbelt, airbag, and occupant detection system in my 2019 BMW 430i. At the time of purchase, the vehicle’s software had not been updated since 2018. Because the software was so outdated, multiple safety-related fault codes did not appear during the dealer’s pre-sale inspect…
Read full complaint
I am reporting a potential safety defect involving the seatbelt, airbag, and occupant detection system in my 2019 BMW 430i. At the time of purchase, the vehicle’s software had not been updated since 2018. Because the software was so outdated, multiple safety-related fault codes did not appear during the dealer’s pre-sale inspection or during initial diagnostic checks. During a later service appointment, the dealership informed me that they were unable to perform accurate diagnostics because the software was old and could interfere with sensor readings. After I paid for the software update, several safety-related codes appeared, including faults connected to the seatbelt/occupant classification system. None of these safety defects were disclosed to me prior to the sale. This raises concern that the vehicle had an existing safety defect at the time of sale, but the outdated software prevented the detection and reporting of these faults. If other vehicles are being sold without current software, this may result in safety-critical issues being hidden from consumers and inspectors. A malfunctioning seatbelt or occupant detection system significantly increases injury risk in a crash. If outdated vehicle software suppresses or fails to display safety-critical faults, consumers may unknowingly be operating unsafe vehicles.
NHTSA ODI #11702674
Mileage unknown · Oct 27, 2025
Electrical System
Rear window does not work. This car collects water from the windows which pools inside the window panel. Eventually, the pooled water damages the window motor and window regulator. Once the window stops working, the convertible top no longer works. This issue is reported all over youtube and google searches. The worse part is th…
Read full complaint
Rear window does not work. This car collects water from the windows which pools inside the window panel. Eventually, the pooled water damages the window motor and window regulator. Once the window stops working, the convertible top no longer works. This issue is reported all over youtube and google searches. The worse part is that to fix this, mechanics have to manually bring down the convertible top. Examples: [XXX] [XXX] [XXX] [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11695883
Mileage unknown · Oct 16, 2025
Air BagsCrash
The airbags did not deploy upon impact from head on collision into another vehicle. The vehicle was towed and the other vehicle’s airbags did deploy that was involved in the collision. There was a police report filed & the insurance company has picked up the vehicle for them to complete an inspection & evaluation.
NHTSA ODI #11693906
Mileage unknown · Aug 1, 2025
Engine
On my way home driving, my car dashboard and LCD screen give me a warning of overheating and engine oil pressure too low. Car stalled on stalled soon after, and started smoking. So I had the car towed and was told from bmw dealership, I had to get a new engine. I have kept up on my oil change and maintenance and never got these …
Read full complaint
On my way home driving, my car dashboard and LCD screen give me a warning of overheating and engine oil pressure too low. Car stalled on stalled soon after, and started smoking. So I had the car towed and was told from bmw dealership, I had to get a new engine. I have kept up on my oil change and maintenance and never got these warning signs until now. I did mr research and found out from Kelly blue book and other websites such Dealer Rater that bmw same year make and model have a few recalls including engine cooling and crankshaft sensor malfunction. The bmw mechanic advise the coolant and oil holder made of plastic melted down into the engine and engine needs to be replaced. However, there have been reports states that other have experience the same thing with bmw cars. This should not have happened when much warnings was not given and how ironic same year make and model had the same issue and recall was issued. I have screen shots to prove it.
NHTSA ODI #11677834
99,000 miles · Feb 10, 2025
Electrical SystemEngine And Engine Cooling
The contact owns a 2019 BMW 430I. The contact stated that while driving at an undisclosed speed, the "Coolant Low" message was displayed, prompting the contact to add coolant to the coolant reservoir. The vehicle returned to normal functionality, but the failure became a regular occurrence. The low coolant warning light was illu…
Read full complaint
The contact owns a 2019 BMW 430I. The contact stated that while driving at an undisclosed speed, the "Coolant Low" message was displayed, prompting the contact to add coolant to the coolant reservoir. The vehicle returned to normal functionality, but the failure became a regular occurrence. The low coolant warning light was illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 24V608000 (Engine and Engine Cooling, Electrical System), but the VIN was not included. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA hotline for assistance. The failure mileage was 99,000.
NHTSA ODI #11641817
86,000 miles · Sep 13, 2024
Air Bags
The contact owns a 2019 BMW 430I. The contact stated that after starting the vehicle and driving at an undisclosed speed, the “Air Bag Off” and “Service Air Bag” messages were displayed. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact related the failure to Special Coverage Adjustment:…
Read full complaint
The contact owns a 2019 BMW 430I. The contact stated that after starting the vehicle and driving at an undisclosed speed, the “Air Bag Off” and “Service Air Bag” messages were displayed. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact related the failure to Special Coverage Adjustment: 23520 Passenger Presence Sensor (PPS) Module; however, the VIN was not included in the Special Coverage Adjustment. The manufacturer was made aware of the failure. The failure mileage was approximately 86,000.
NHTSA ODI #11614401
Mileage unknown · Jul 31, 2024
EnginePower TrainUnknown Or Other
I purchased my vehicle October2023. May 23,2024, at 1:34 pm, my vehicle broke down due to a message on my dashboard stating “Drivetrain malfunction”. I was on the highway with no use of my gas pedal, which resulted in me rolling back all while being 5 months pregnant. June 18,2024, at 3:04pm ,my vehicle broke down again due to …
Read full complaint
I purchased my vehicle October2023. May 23,2024, at 1:34 pm, my vehicle broke down due to a message on my dashboard stating “Drivetrain malfunction”. I was on the highway with no use of my gas pedal, which resulted in me rolling back all while being 5 months pregnant. June 18,2024, at 3:04pm ,my vehicle broke down again due to the same message that previously popped up “Drivetrain malfunction”. I was also on the highway with no use of my gas pedal all while pregnant. July 18,2024, at 12:25 midnight, my vehicle broke down again due to the previous problem “Drivetrain malfunction” by the airport with no use of my gas pedal all while 6 months pregnant. Each time I my vehicle malfunction I almost got hit by other vehicles because I had no use of my gas pedals to get out of the way. There were no warning signs at all. When the message pops up on my dashboard the gas pedal completely becomes inoperable. This vehicle has put me and my soon to be baby in harms way multiple times. The dealership has had 3 times to fix the problem and still fail to do so. Having their opportunity to fix it three times just to tell me it’s because it doesn’t have gas in it when it did has put my in a situation where I’m constantly worried about it braking down again putting me and my unborn child in danger AGAIN, to where I am financing a car I can not use. Not including the 2 times I had to pay to get it towed from the airport because the police told me I couldn’t leave it there.
NHTSA ODI #11605588
Official recalls
3May 9, 2019
BMW of North America, LLC (BMW) is recalling certain 2019-2020 230i, 230i xDrive, M240i, M240i xDrive, M2 Competition Coupe, 430i, 430i xDrive, 440i, 440i xDrive, M4, and 2019 330i xDrive Sportswagon vehicles. The driver and passenger knee air bag assemblies may have been improperly folded and assembled.
Consequence & remedy
Consequence: An improperly folded and assembled air bag may not deploy as intended, increasing risk of injury.
Remedy: BMW will notify owners, and dealers will replace the knee air bag modules, free of charge. The recall began July 8, 2019. Owners may contact BMW customer service at 1-800-525-7417.
Aug 15, 2018
BMW of North America, LLC (BMW) is recalling one each of 2019 BMW 430i xDrive Gran Coupe, 440i xDrive Gran Coupe and 430i xDrive Convertible vehicles. The front passenger air bag inflator may have been incorrectly manufactured, potentially affecting the air bag deployment performance in the event of a crash.
Consequence & remedy
Consequence: If the front passenger air bag does not deploy properly in the event of a crash, the occupant has an increased risk of injury.
Remedy: All affected vehicles are still in dealer inventory. Dealers will replace the front passenger air bag module, free of charge.
Jul 11, 2018
BMW of North America, LLC (BMW) is recalling certain 2018 BMW 540d xDrive vehicles. The crankshaft sensor may be equipped with incorrect firmware, preventing the sensor from properly processing input from the crankshaft reluctor ring, possibly resulting in a vehicle stall. On September 12, 2018, BMW expanded the recall to a total of 5,309 vehicles including certain 2018-2019 BMW 540d xDrive, 230i M240i, M240i xDrive, X2 sDrive28i, X2 xDrive28i, X1 sDrive28i, X1 xDrive28i, 330i, 330i xDrive, 340i, 340i xDrive, 330i xDrive Gran Turismo, 530i, 530i xDrive, 540i, 540i xDrive, 530e, 530e xDrive, 640i xDrive Gran Turismo, 330e, 2019 430i Gran Coupe, 430i xDrive Gran Coupe, 440i Gran Coupe, 440i xDrive Gran Coupe, 430i, 430i xDrive, 440i, 440i xDrive, 740i, 740i xDrive, MINI Cooper, Cooper S, JCW, MINI Countryman (Cooper, Cooper All4, Cooper S, Cooper S All4, JCW All4), and MINI Clubman (Cooper, Cooper S, Cooper All4, Cooper S All4, JCW All4) vehicles.
Consequence & remedy
Consequence: A vehicle stall can increase the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the crankshaft sensor, free of charge. The recall began September 6, 2018. Owners may contact BMW customer service at 1-800-525-7417.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration