My 2015 BMW 328i xDrive (VIN [XXX] ) experienced an engine-compartment fire that began shortly after coolant sprayed from the front of the vehicle. This incident occurred before BMW’s official recall announcement for NHTSA Campaign 24V-608 / BMW 24V-608:474 (Safety: Engine Coolant Pump Electrical Connector). The fire originated …
Read full complaint
My 2015 BMW 328i xDrive (VIN [XXX] ) experienced an engine-compartment fire that began shortly after coolant sprayed from the front of the vehicle. This incident occurred before BMW’s official recall announcement for NHTSA Campaign 24V-608 / BMW 24V-608:474 (Safety: Engine Coolant Pump Electrical Connector). The fire originated near the coolant pump area, consistent with the recall’s described defect involving electrical shorting and overheating at the pump connector. The vehicle was declared a total loss by my insurance company. I believe this event was caused by the same defect identified in the recall and request that this incident be investigated and documented under campaign 24V-608. Supporting photos and insurance documentation are available upon request. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11695569
Mileage unknown · Sep 26, 2025
Power TrainService Brakes
Virtually all parking brake cable attachment clips fail on this BMW product years 2012 to 2019. Complaints are easy to find online. Upon failure, the parking brake cable drops down onto the drive shaft creating a safety hazard for the brake system as well as the drive shaft mechanism. The piece that fails (breaks) costs less tha…
Read full complaint
Virtually all parking brake cable attachment clips fail on this BMW product years 2012 to 2019. Complaints are easy to find online. Upon failure, the parking brake cable drops down onto the drive shaft creating a safety hazard for the brake system as well as the drive shaft mechanism. The piece that fails (breaks) costs less than $20, but replacement costs $1200 due to labor intensive access. I have repeatedly contacted BMW of North America, but they refuse to own this serious issue. Even the people at the BMW dealership here are surprised that there has been no recall. Please advise.
NHTSA ODI #11689985
Mileage unknown · Jun 21, 2025
EngineFuel/propulsion SystemPower Train
Engine coolant pump recall (August 2024) with no remedy to this day. Has caused major smoking issues from exhaust and engine. The turbocharger has been affected and deemed inoperable. Fluid leaks from chassis and engine bay. The car is inoperable. Prior to being unable to drive I was experiencing transmission issues, went for …
Read full complaint
Engine coolant pump recall (August 2024) with no remedy to this day. Has caused major smoking issues from exhaust and engine. The turbocharger has been affected and deemed inoperable. Fluid leaks from chassis and engine bay. The car is inoperable. Prior to being unable to drive I was experiencing transmission issues, went for a few repairs but would experience the car coming to a complete stop on its own at highway speeds. Experienced this on the bridge, being left stuck and almost causing a wreck. Made the bridge very unsafe for others. I had a “drive train malfunction” warning& check engine light that I thought was fixed with multiple mechanic trips but problems have only gotten worse. No inspections have been done in regards to the recall. The car has sat unable to drive for 2 full months now.
NHTSA ODI #11668307
Mileage unknown · Apr 3, 2025
Power Train
The parking brake cable bracket is a cheap piece of plastic that fails on every single BMW model like mine from this era, which means the parking brake cable comes in contact with the drive shaft. Mine has broken. Dealers charge $1,100 to replace with an equally cheap 30 dollar plastic bracket. Replacement is labor intensive whi…
Read full complaint
The parking brake cable bracket is a cheap piece of plastic that fails on every single BMW model like mine from this era, which means the parking brake cable comes in contact with the drive shaft. Mine has broken. Dealers charge $1,100 to replace with an equally cheap 30 dollar plastic bracket. Replacement is labor intensive which explains the high fee (I guess). BMW mechanics as well as BMW owner internet forums tell me that this fails on every single car. This is a real hazard, as it can cause parking brake failure and drive shaft damage. Owners are very upset with BMW for not taking care of this obvious design flaw. My car has all of 52,000 miles on the odometer. This needs to be a recall!! BMW refuses to take care of this, just as they have refused to take care of the existing water pump recall. Thanks in advance for taking care of this safety issue.
NHTSA ODI #11652662
Mileage unknown · Mar 7, 2024
Power Train
I own a 2015 BMW 328i xdrive with 86k miles. While reversing out of my driveway, onto a main road during rush hour, my vehicle unexpectedly stopped working with the message “drivetrain malfunction”. I had the car towed to a BMW dealership and was told there was a fault found in VANOS intake and that my car needed a timing chain …
Read full complaint
I own a 2015 BMW 328i xdrive with 86k miles. While reversing out of my driveway, onto a main road during rush hour, my vehicle unexpectedly stopped working with the message “drivetrain malfunction”. I had the car towed to a BMW dealership and was told there was a fault found in VANOS intake and that my car needed a timing chain replacement. I called BWM NA and was informed that there is a VANOS recall, but not for my car. They did however tell me that BMW would compensation for timing chain repairs for my 2015 328i if the car fell within certain parameters, low miles and within 7 years. While my car has low miles, I was told that my recall for the part had been “cleared” because I’m outside of the 7 year allotment for compensation on timing chain repairs. BMW will not help fix the timing chain nor compensate in anyway. I was informed they sent a letter in 2017, I purchased the car in 2017 and did not receive a letter. My vehicle had been serviced multiple times at BMW dealerships and I was never informed about a timing chain recall, not even in 2018 when my car was serviced at BMW for check engine light on. BWM has purposely avoided fixing a major vehicle flaw that they’ve known about.
NHTSA ODI #11576125
Mileage unknown · Nov 16, 2023
Power Train
My drivetrain malfunction light comes on and my vehicle stalls while I’m driving it.
NHTSA ODI #11555553
Mileage unknown · Aug 22, 2023
EnginePower TrainSuspension
After consulting many others that own or previously owned 328i bmw from around the same years (2015-2017); a common issue was found and assumed to be the timing belt. when i press on the accelerator moderately/ as per usual, my RPMs and speedometer hesitate for a solid second then it will catch up and start shaking. i suspect it…
Read full complaint
After consulting many others that own or previously owned 328i bmw from around the same years (2015-2017); a common issue was found and assumed to be the timing belt. when i press on the accelerator moderately/ as per usual, my RPMs and speedometer hesitate for a solid second then it will catch up and start shaking. i suspect its the timing belt.
NHTSA ODI #11540161
Mileage unknown · Sep 3, 2022
EnginePower Train
Driving to work and the engine oil pressure warning came up and the car began to decelerate and once completely stopped the power train malfunction warning popped up and I couldn’t restart the engine. Towed to BMW of Toledo and was Told the timing chain broke and destroyed the engine.
NHTSA ODI #11482766
Mileage unknown · May 18, 2022
Power TrainUnknown Or Other
The drivetrain malfunction light came on and my car stopped on the main highway while I was driving out and it wouldn’t start back so a wrecker tow it then maybe 5 days later it just crank again but then it started to do it again. There was a recall for this but it had expired before I bought the car
NHTSA ODI #11465134
Mileage unknown · Jan 14, 2022
Power TrainUnknown Or Other
Vehicle smells like gas. Drivetrain malfunction light comes on, car sputters and shakes, goes off after a couple of days and then comes back on and shakes 4 months or more later. Loses power or won’t accelerate while traveling more than 50 mph
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Engine And Engine Cooling:cooling System:pump
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, increasing the risk of injury or death.
Remedy: The driver's front air bag will be replaced, free of charge. Owner notification letters were mailed September 6, 2024. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2014-2015 2 Series Coupe (228i, 228i xDrive, M235i), 3 Series Sedan (320i, 320i xDrive, 328i, 328i xDrive, 335i, 335i xDrive, M3, 328d, 328d xDrive), 4 Series Coupe (428i, 428i xDrive, 435i, 435i xDrive, M4), and 2015 4 Series Gran Coupe (428i, 428i xDrive, 435i, 435i xDrive) vehicles. The head air bag inflator may fail at the weld joint, which can cause gas to leak from the inflator or result in an inflator rupture.
Consequence & remedy
Consequence: An inflator that ruptures may cause sharp metal fragments to enter or exit the vehicle, increasing the risk of injury. Additionally, an inflator that leaks gas may only partially inflate during a crash, increasing the risk of injury.
Remedy: Dealers will replace the head air bags, free of charge. Owner notification letters were mailed November 4, 2024. Owners may contact BMW customer service at 1-800-525-7417.
BMW North America, LLC (BMW) is recalling certain model year 2012-2015 320i, 320xi, 328i, 328xi, 335i, 335xi, and ActiveHybrid3 vehicles manufactured October 20, 2011, to June 22, 2015, 2014-2015 328xi Sports Wagon vehicles manufactured March 21, 2013, to March 17, 2015, 2014-2015 328d, 328xd vehicles manufactured June 28, 2013, to April 21, 2015, and 2014-2015 328xd Sports Wagon vehicles manufactured July 5, 2013, to April 21, 2015. The affected vehicles may have been programmed with new software that inadvertently makes the front side marker lights inoperative in conjunction with the parking lights or the headlights. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence & remedy
Consequence: If the side marker lights do not illuminate, the vehicle may be less visible at night, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will upload revised software to correct the issue, free of charge. The recall began on October 7, 2015. Owners may contact BMW customer service at 1-800-525-7417 or by email at CustomerRelations@bmwusa.com.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
2015 BMW 328I Problems, Complaints & Recalls | Skip That Year
Illustration