WHILE DRIVING BOTH IN REGULAR TRAFFIC AND HIGHWAY TRAFFIC THE CAR HAS WITHOUT WARNING GONE INTO A LIMP MODE SHUDDERING ALLOWING NO POWER AT ALL TO THE ACCELERATOR. A MESSAGE POPS UP "DRIVETRAIN MALFUNCTION MAXIMUM DRIVETRAIN OUTPUT NOT AT AVAILABLE. IF YOU GET PULLED OVER TURN THE VEHICLE OFF WAIT A COUPLE MINUTES TURN THE IGN…
Read full complaint
WHILE DRIVING BOTH IN REGULAR TRAFFIC AND HIGHWAY TRAFFIC THE CAR HAS WITHOUT WARNING GONE INTO A LIMP MODE SHUDDERING ALLOWING NO POWER AT ALL TO THE ACCELERATOR. A MESSAGE POPS UP "DRIVETRAIN MALFUNCTION MAXIMUM DRIVETRAIN OUTPUT NOT AT AVAILABLE. IF YOU GET PULLED OVER TURN THE VEHICLE OFF WAIT A COUPLE MINUTES TURN THE IGNITION BACK ON THE VEHICLE RUNS LIKE THAT NEVER HAPPENED. THIS IS EXTREMELY DANGEROUS IF THE VEHICLE GOES LIMP NO POWER WHILE ON THE FREEWAY IN FRONT OF A BIG 18 WHEELER IT HAPPENED TO ME THE OTHER VEHICLES DO NOT UNDERSTAND YOUR VEHICLE JUST DIED WHILE GOING 75 MPH.
NHTSA ODI #11415281
79,825 miles · Oct 9, 2020
Fuel/propulsion System
FUEL TANK SPLIT AT FACTORY SEAM CAUSING FUEL TO POUR OUT OF TANK WHEN FULL. THIS ISSUE HAPPENED AFTER FILLING TANK AND DRIVING A SHORT DISTANCE. WHEN I CAME OUT TO MY CAR WHICH WAS PARKED, I NOTICED A LARGE PUDDLE OF GAS UNDER THE DRIVER'S SIDE OF THE VEHICLE.
NHTSA ODI #11363582
113,000 miles · Jun 11, 2019
EngineFuel/propulsion System
WHILE DRIVING ON THE INTERSTATE OR OVER 50 MPH THE VEHICLE WILL NOT ALLOW ME TO GIVE IT GAS AND A "DRIVETRAIN MALFUNCTION" COMES ON. THE CAR THEN GOES INTO LIMP MODE AND THE ENGINE SHAKES. THE VEHICLE WILL NOT ALLOW ME TO GIVE IT GAS AND BEFORE THE "DRIVETRAIN MALFUNCTION" COMES ON YOU CAN FEEL THE GAS OR FUEL PUMP JERK. THEN I …
Read full complaint
WHILE DRIVING ON THE INTERSTATE OR OVER 50 MPH THE VEHICLE WILL NOT ALLOW ME TO GIVE IT GAS AND A "DRIVETRAIN MALFUNCTION" COMES ON. THE CAR THEN GOES INTO LIMP MODE AND THE ENGINE SHAKES. THE VEHICLE WILL NOT ALLOW ME TO GIVE IT GAS AND BEFORE THE "DRIVETRAIN MALFUNCTION" COMES ON YOU CAN FEEL THE GAS OR FUEL PUMP JERK. THEN I AM NO LONGER ABLE TO GIVE THE CAR GAS, LIMP BODE HAPPENS, ENGINE SHAKES, AND THE CAR PUTS ITSELF IN NEUTRAL. I HAVE TO FIND A WAY TO GET IN THE EMERGENCY LANE WITHOUT GETTING HIT AND TURN THE CAR OFF FOR A FEW MINUTES TO RESET THE LIGHTS. BUT THIS HAS HAPPENED ON MORE THAN ONE OCCASION. I HAVE TAKEN IT TO A BODY SHOP TWICE, STILL NOT FIXED.
NHTSA ODI #11219191
Mileage unknown · Dec 24, 2018
Fuel/propulsion SystemUnknown Or Other
MY CAR SMELLS LIKE GASOLINE AND IS LEAKING GAS
NHTSA ODI #11163277
17,000 miles · Aug 4, 2016
Fuel/propulsion System
WHILE IN MOTION ON AN INTERSTATE THE CAR SUDDENLY STARTED TO SPUTTER AND LOSE MOMENTUM. AT THE SAME TIME, A WARNING ALERTED US TO A "DRIVE TRAIN MALFUNCTION". LUCKILY, WE WERE IN THE LANE CLOSEST TO THE SIDE OF THE ROAD AND WE WERE ABLE TO LIMP OFF THE ROAD AND OUT OF TRAFFIC. THE CAR WAS TOWED TO THE NEAREST BMW DEALER IN LAS V…
Read full complaint
WHILE IN MOTION ON AN INTERSTATE THE CAR SUDDENLY STARTED TO SPUTTER AND LOSE MOMENTUM. AT THE SAME TIME, A WARNING ALERTED US TO A "DRIVE TRAIN MALFUNCTION". LUCKILY, WE WERE IN THE LANE CLOSEST TO THE SIDE OF THE ROAD AND WE WERE ABLE TO LIMP OFF THE ROAD AND OUT OF TRAFFIC. THE CAR WAS TOWED TO THE NEAREST BMW DEALER IN LAS VEGAS WHERE THE PROBLEM WAS DETERMINED TO BE A FAILED HIGH PRESSURE FUEL PUMP. THE CAR HAS LESS THAN 17,000 MILES. AFTER SOME RESEARCH, WE FOUND THAT BMW HAS A HISTORY OF FUEL PUMP RECALLS ALTHOUGH NONE FOR OUR MODEL YEAR. THIS INCIDENT WAS QUITE DANGEROUS CONSIDERING THE CAR SUDDENLY BEING INOPERABLE AT A HIGH RATE OF SPEED ON THE INTERSTATE. WERE WE NOT IN THE RIGHT HAND LANE, THE INCIDENT COULD HAVE BEEN DEADLY.
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Engine And Engine Cooling:cooling System:pump
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, increasing the risk of injury or death.
Remedy: The driver's front air bag will be replaced, free of charge. Owner notification letters were mailed September 6, 2024. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2014-2015 2 Series Coupe (228i, 228i xDrive, M235i), 3 Series Sedan (320i, 320i xDrive, 328i, 328i xDrive, 335i, 335i xDrive, M3, 328d, 328d xDrive), 4 Series Coupe (428i, 428i xDrive, 435i, 435i xDrive, M4), and 2015 4 Series Gran Coupe (428i, 428i xDrive, 435i, 435i xDrive) vehicles. The head air bag inflator may fail at the weld joint, which can cause gas to leak from the inflator or result in an inflator rupture.
Consequence & remedy
Consequence: An inflator that ruptures may cause sharp metal fragments to enter or exit the vehicle, increasing the risk of injury. Additionally, an inflator that leaks gas may only partially inflate during a crash, increasing the risk of injury.
Remedy: Dealers will replace the head air bags, free of charge. Owner notification letters were mailed November 4, 2024. Owners may contact BMW customer service at 1-800-525-7417.
BMW North America, LLC (BMW) is recalling certain model year 2012-2015 320i, 320xi, 328i, 328xi, 335i, 335xi, and ActiveHybrid3 vehicles manufactured October 20, 2011, to June 22, 2015, 2014-2015 328xi Sports Wagon vehicles manufactured March 21, 2013, to March 17, 2015, 2014-2015 328d, 328xd vehicles manufactured June 28, 2013, to April 21, 2015, and 2014-2015 328xd Sports Wagon vehicles manufactured July 5, 2013, to April 21, 2015. The affected vehicles may have been programmed with new software that inadvertently makes the front side marker lights inoperative in conjunction with the parking lights or the headlights. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence & remedy
Consequence: If the side marker lights do not illuminate, the vehicle may be less visible at night, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will upload revised software to correct the issue, free of charge. The recall began on October 7, 2015. Owners may contact BMW customer service at 1-800-525-7417 or by email at CustomerRelations@bmwusa.com.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
2015 BMW 328I Problems, Complaints & Recalls | Skip That Year
Illustration